24-Port Gigabit, Enterprise-Class, Fully Managed Switch

S24P8
24-Port Gigabit, Enterprise-Class, Fully Managed
Switch with 8 Power-over-Ethernet Ports
Quick Start Guide – Version 1.0
Table of Contents
Introduction ................................................................................................................................................................................................... 3
Quick Switch Overview .............................................................................................................................................................................. 3
Preparing to Install the Switch .................................................................................................................................................................... 5
Installation ..................................................................................................................................................................................................... 5
Configuration Methods .............................................................................................................................................................................. 6
Configuring the Switch Using the Web Interface ................................................................................................................................ 6
Changing the IP Address of the Switch ...............................................................................................................................................9
Setting the Default Gateway IP Address ...........................................................................................................................................10
Configuring VLANs .............................................................................................................................................................................. 11
Power Cycling PoE Ports ..................................................................................................................................................................... 17
Configuring the Switch Using the Supplied Console Cable ............................................................................................................. 19
Resetting the IP Address of the Switch .............................................................................................................................................. 21
Resetting the Switch to Factory Default ............................................................................................................................................. 2
2
Troubleshooting & Support ........................................................................................................................................................................ 23
Figures
Figure 1: S24P8 Front Panel ........................................................................................................................................................................3
Figure 2: S24P8 Rear Panel ........................................................................................................................................................................4
Figure 3: Login Web Interface (Windows 7) ............................................................................................................................................7
Figure 4: S24P8 Web Interface .................................................................................................................................................................8
Figure 5: IP Address of Switch ....................................................................................................................................................................9
Figure 6: Default Gateway .........................................................................................................................................................................10
Figure 7: S24P8 Switch Setup Example with Pakedge’s K62 Kit .........................................................................................................12
S24P8 QUICK START GUIDE
1
Figure 8: VLAN Configuration ..................................................................................................................................................................13
Figure 9: Correct VLAN Port Configuration for WAP ...........................................................................................................................14
Figure 10: Wired VLAN Tagging ............................................................................................................................................................15
Figure 11: VLAN Information ....................................................................................................................................................................16
Figure 12: PoE Power Control ..................................................................................................................................................................17
Figure 13: Console Connection in Terminal Window ...........................................................................................................................19
Tables
Table 1: LED Light Explanation ...................................................................................................................................................................3
Table 2: S24P8 Rear Panel Port Description ..............................................................................................................................................4
Table 3: Port Configuration Key .................................................................................................................................................................11
Table 4: Default Serial Port Settings for Console Connection ...............................................................................................................18
S24P8 QUICK START GUIDE
2
1. INTRODUCTION
This guide has been written to help you get up-and-running quickly with the Pakedge S24P8 Power over Ethernet
(PoE) switch, with a few assumptions in mind:
a. You have a working knowledge of networking hardware configurations
b. You have a working knowledge of PC operations
QUICK SWITCH OVERVIEW
This Quick Start Guide has been written for the S24P8 Gigabit PoE switch. The Front Panel of the S24P8 (shown in
Figure 1) has several LEDs to display the status of the switch ports. The explanations of the lights are found in Table1.
Figure1: S24P8 Front Panel
LabelFunction
PWR
Description
Power indicator light
When lit, indicates that unit has power.
Indicator lights when Ethernet link is normal.
Link/Act Link and Act Indicator of each port
Indicator blinks when data is sent or received.
PoE (Ports
PoE
Indicator
of
PoE
port
Indicator
lights when PoE is being provided on this port.
1-8)
SFP
Speed Indicator of SFP port
Indicator is lit when the port is in using fiber connection.
Table 1: LED Light Explanation
S24P8 QUICK START GUIDE
3
The rear panel (Figure 2) is where the connection ports to power and other equipment are located.
Table 2 describes each port and its function.
Figure 2: S24P8 Rear Panel
NameExplanation
AC connector
AC110 ~ 260V
Grounding bar
Please ground as needed.
Up to 24 10/100/1000M ports
Speed: 10/100/1000 M auto-sense; cable: MDI/MDIX,
UTP (RJ45) interface with LINK/ACT, PoE indicator (Ports 1-8)
Up to 8 10/100/1000M PoE ports
PoE: IEEE 802.3af, Speed: 10/100/1000 M auto-sense
Up to 4 SFP Ports
Speed: 10/100/1000M auto-sense; cable: Fiber Optic
CONSOLE
Implement Switch Local management. Speed: 38400bps,
RJ45 interface
Table 2: S24P8 Rear Panel Port Description
S24P8 QUICK START GUIDE
4
PREPARING TO INSTALL THE SWITCH
Installing the S24P8 is similar to installing any other PoE Switch. If you have installed an Ethernet switch
before, the process will be very similar.
Tools Required:
•Phillips Screwdriver (if using rack-mount brackets)
•PC or Laptop with Ethernet Interface and a web browser (an integrated DB-9 port or USB-to-Serial
adapter may be necessary if you would like to use the console interface)
•Ethernet Cable
INSTALLATION
1.Open box and remove unit.
2. OPTIONAL: If mounting the switch in a standard 19” AV rack, attach the rack-mounting brackets that
come with the S24P8 to the sides. If not rack-mounting, ensure that the switch is physically mounted near
power and network connections. (i.e., backbone switch or firewall/router).
3.Connect power to the device.
4.Connect an Ethernet cable from your computer to any port on the switch.
5.You are now ready to configure the switch to an IP address that matches your network.
S24P8 QUICK START GUIDE
5
CONFIGURATION METHODS
There are two ways to complete the initial configuration of the S24P8 switch – either by using the standard
IP address and a web browser or the console cable and a terminal emulation program such as PuTTY or
HyperTerminal.
IMPORTANT NOTE: This Quick Start Guide only provides instructions for resetting the IP Address of the
switch and restoring it back to Factory Default with the console cable. Please reference the User’s Manual on
our website for additional CLI commands.
CONFIGURING THE SWITCH USING THE WEB INTERFACE
1.Connect the switch to power. Power LED will light up and switch fans will start.
2.Connect a PC or laptop to any standard Ethernet Port on the switch.
3.Configure the PC with the Static IP address of 192.168.1.10, and subnet mask of 255.255.255.0 and
then open any web browser. Internet Explorer, Mozilla, and Chrome browsers all work for configuring the
S24P8, but Internet Explorer is preferred.
4.In the browser, enter the switch’s default IP address of 192.168.1.205 into the Address Bar and press
<ENTER>.
5.A window similar to the one in Figure 3 (p.7) will appear, prompting you for a username and password.
Enter admin for the username and leave the password field blank. Then, click “OK” to log into the web
administration portal.
6.Once you have logged into the switch, you will see the web interface as pictured in Figure 4 (p.8).
S24P8 QUICK START GUIDE
6
Figure 3: Login Web Interface (Windows 7)
Once you have access to the web GUI of the switch, you can customize the configuration to your
environment. We have included common configurations in the next sections for your convenience. To access
the full spectrum of configurations, please refer to the User’s Manual on our website.
S24P8 QUICK START GUIDE
7
Figure 4: S24P8 Web Interface
S24P8 QUICK START GUIDE
8
CHANGING THE IP ADDRESS OF THE SWITCH
To change the default IP Address of the switch, please follow these instructions:
1.Open the “IP Configuration” folder in the GUI and click on “IP Address Configuration.”
2.Under “Line Item” select “1.” Your page will reset and you can now enter the new IP Address under
“IP Address / Subnet Prefix.”
3.Once you are done, click on “Create/Modify IP Address” and your new IP will be saved as seen in
Figure 5.
Figure 5: IP Address of the Switch
S24P8 QUICK START GUIDE
9
SETTING THE DEFAULT GATEWAY IP ADDRESS
To set a default gateway on the switch in order to access it from anywhere on the network, please follow
these instructions:
1. Open the “IP Configuration” folder in the GUI and click on “Host Static Router Configuration.”
2. Enter “0.0.0.0/0” under “Target Address/Subnet Prefix.”
3. Enter the router’s IP address in the “Next Hop” field.
4.Click “Apply” and you should see a page that resembles Figure 6.
Figure 6: Default Gateway
S24P8 QUICK START GUIDE
10
CONFIGURING VLANs
The S24P8 switch has an advanced web interface that allows you to configure each port on the switch to
the desired VLAN. It is important to configure the ports on the switch with the correct VLAN settings to reflect
what you are trying to accomplish on the network. This Quick Start Guide provides instructions for configuring
the ports of the switch when using a Wireless Access Point or a wired connection with VLAN tagging.
Switch
VLAN
Device Connected Required Port Configuration
S24P8*
802.1Q Trunk (All VLANs) Wireless Access Point Hybrid Mode
S24P8*
VLAN 2
VOIP Phones
Specific ports set to Access Mode
VLAN 3
Security Cameras
Specific ports set to Access Mode
S24P
VLAN 4
Automation Devices
All ports set to Access Mode
SW24-GB
VLAN 5
Home Computers
Trunk port (Default)
* The port connected to the router needs to be set in Hybrid Mode to work properly.
Table 3: Port Configuration Key
Table 3 and Figure 7 provide a network configuration example that you may use as a guide to properly
configure the switches on your network.
S24P8 QUICK START GUIDE
11
Figure 7: S24P8 Switch Setup Example with Pakedge’s K62 Kit
S24P8 QUICK START GUIDE
12
Figure 8: VLAN Configuration
CONFIGURING HYBRID
PORTS FOR WIRELESS ACCESS
POINTS
If you are connecting a
Wireless Access Point
(WAP) to a port, please
follow these steps:
1.The first thing to do inside
the switch is to create
the VLANs. Start by
expanding the “VLAN
Configuration” folder and then click on “VLAN Configuration.” In the VID field, enter the
number of the VLAN you want to create and then click “Apply.” You can repeat this process to
create the desired number of VLANs as shown in Figure 8.
2.Next, configure the port to allow the VLANs to pass through. Click on “VLAN Port
Configuration” and under the Port dropdown select the port you are connecting the WAP to.
Under the model dropdown select “Hybrid,” under “Current VLAN” highlight “vlan1” and then
click “Default VLAN.” (Make sure vlan1 is an untagged member of the port).
S24P8 QUICK START GUIDE
13
Figure 9: Correct VLAN Port
Configuration for WAP
3.Now click on the next VLAN
in the list under “Current
VLAN,” and then click on
“tagged.” You will need
to do this for all remaining
VLANs in the “Current
VLAN” list that you want to
use with this port. You can
also highlight all the VLANs at once and click “tagged” to make them all members of the port. The
end result should look something like Figure 9.
4.You may repeat this process to configure any necessary ports the same way in the switch.
NOTE:
The port which will be used to connect to the router must be configured as a “Hybrid” port.
S24P8 QUICK START GUIDE
14
Figure 10: Wired VLAN
Tagging
CONFIGURING ACCESS
PORTS FOR VLAN TAGGING
1.Click and open the “VLAN
Configuration” folder.
2.Select the port you want
to change under the
Port column, then select
“Access” under Model.
Select the desired VLAN
under “Current VLAN” and click on “Default VLAN.” The configuration should look like Figure
10.
3.Once the port is configured this way, any device that plugs into that port will receive the assigned
VLAN tag.
S24P8 QUICK START GUIDE
15
Figure 11: VLAN Information
NOTE:
To check your current
configuration, you can go to
“VLAN Information” and see
a summary of which ports are
configured to which VLANs.
See Figure 11.
NOTE:
The switch will save every
configuration you perform automatically and load it the next time the switch is rebooted. You DO NOT
need to hit the save button after every change.
S24P8 QUICK START GUIDE
16
Figure 12: PoE Power Control
POWER CYCLING PoE PORTS
The S24P8 switch allows the user to
power cycle each port from the GUI
screen of the switch. This feature is
very useful if you have devices that
are located in hard-to-reach places
and need to be power-cycled for
any reason.
NOTE: Only the devices that are powered on through PoE will be affected by the power cycle.
Please follow these instructions to power cycle PoE devices:
1. Within the GUI of the switch, expand the “PoE Power Control” folder and click on “PoE Power
Control.” You should see a screen similar to Figure 12.
2. Next to the “PoE Port” drop down menu, select the port you wish to power cycle.
3. In the “PoE Power Status” drop down menu, select “disable” and click “Apply.” You have now
successfully turned off power to that port.
4. To turn power back on, select the port you wish to turn on and choose “enable” in the “PoE Power
Status” field. Then click “Apply” and your port will begin sending power to the device.
5. Wait 2-3 minutes for your device to start working properly. You should then have access to it if
everything is working properly on the network.
S24P8 QUICK START GUIDE
17
CONFIGURING THE SWITCH USING THE SUPPLIED CONSOLE CABLE
Configuring the switch using the console cable method is more involved. However, this method is helpful if the
Ethernet interfaces are not functioning properly or the incorrect IP address was accidentally set on the switch,
rendering it inaccessible through the web interface.
1.In order to connect to the switch, you must first have a PC with a DB-9 serial port or a USB-to-Serial
adapter. In addition, you need to use software such as HyperTerminal or PuTTY (available for free on the
Internet) to connect to the switch’s command line console.
2.Once you have located the serial port on your computer, plug the supplied Console Cable into the
computer and the switch (DB9 end to the computer and
Baud Rate
38400
RJ-45 end into the switch’s “Console” port).
Character Size 8
3.When your physical connection is set up, configure your
terminal software to connect to the switch. You should
Parity Code None
already know which COM port your PC uses for a serial
Stop Bits 1
port (COM1 or COM2 on most computers, COM1
Flow Control None
through COM10 if using a USB-to-Serial adapter).
Table 4: Default Serial Port Settings for
4.In addition to the COM port number, Table 4 shows
Console Connection
the necessary settings that must be set in the terminal
communications software in order to make a successful
connection.
5.Once the connection is properly established, you should see a screen similar to Figure 13 (p.19).
S24P8 QUICK START GUIDE
18
Figure 13: Console Connection
in Terminal Window
S24P8 QUICK START GUIDE
19
RESETTING THE IP ADDRESS OF THE SWITCH
To configure your switch back to the default network IP address of 192.168.1.205 with a subnet of
255.255.255.0, complete the following steps:
1.Establish a connection with the switch using the instructions previously listed. You will see a screen
similar to the one in Figure 13. Once this screen appears, type enable and hit <ENTER>. You will see
the prompt change from Switch> to Switch#.
2.Type conf t and press <ENTER>.
3.Type interface vlan1 and press <ENTER>.
4.Type ip address 192.168.1.205/24 and press <ENTER>.
5.Press <CTRL> Z.
6.Type write (you will see Building and writing configuration ...).
7.Type copy run start (you will see Building and writing configuration ...).
8.Your switch should now be accessible from the network.
S24P8 QUICK START GUIDE
20
RESETTING THE SWITCH TO FACTORY DEFAULT
NOTE: RESETTING THE SWITCH TO FACTORY DEFAULT WILL DELETE ALL OF YOUR
CONFIGURATIONS.
1.Establish a connection with the switch using the console cable. You will see a screen similar to the
one in Figure 13 (p.19). Once this screen appears, type enable and hit <ENTER>. You will see the
prompt change from Switch> to Switch#.
2.Type delete startup-config and press <ENTER>
3.When you see: Do you wish to continue? [Y/N] – press <Y>
4.Now, type reset and press <ENTER>, then press <Y>
5.The switch will automatically reboot and will be restored to factory default.
S24P8 QUICK START GUIDE
21
TROUBLE SHOOTING & SUPPORT
If you are unable to get the S24P8 switch functional using these steps, you can refer to the User’s Manual on
our website or contact the Technical Support Team for help.
CONTACT INFORMATION:
Website: www.pakedge.com
Email: [email protected]
Phone: 650.385.8703
Please be prepared to provide your product’s model and serial number when contacting Pakedge Support.
Your model and serial numbers are printed on a label located on the electronic housing.
S24P8 QUICK START GUIDE
22
1163 Triton Drive
Foster City, CA 94404
U.S.A.
© Pakedge Device & Software Inc. 2011 – All Rights Reserved