1. No category

List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
This list identifies works approved by Lloyd’s Register Group Limited (LR) for refining and
the manufacture of aluminium alloy plates, sections, bars and castings in accordance with
the requirements of LR's Rules for the Manufacture, Testing and Certification of Materials,
Chapter 8.
The information listed for each works is a summary of the product, grade and maximum
thickness (for round bar, maximum diameter and for castings, maximum weight)
Where required further information should be obtained from the current certificate of
approval issued to the manufacturer by LR.
Works designated "MQS Approved" are also approved under the Materials Quality Scheme
in accordance with LR's Rules for the Manufacture, Testing and Certification of Materials,
Chapter 1 Section 2.
Approval only covers the manufacturing location listed, it does not extend to other works
owned by the same company.
The local LR surveying office is also listed.
Lloyd's Register Group Limited, its affiliates and subsidiaries and their respective officers,
employees or agents are, individually and collectively, referred to in this clause as 'Lloyd's
Register'. Lloyd's Register assumes no responsibility and shall not be liable to any person
for any loss, damage or expense caused by reliance on the information or advice in this
document or howsoever provided, unless that person has signed a contract with the
relevant Lloyd's Register entity for the provision of this information or advice and in that
case any responsibility or liability is exclusively on the terms and conditions set out in that
contract.
As at 11 February 2015
© Lloyd’s Register Group Limited 2015. All rights reserved.
This is a copy of an electronic document. In the event of any conflict or ambiguity between the copy and the electronic document,
which is retained and published by Lloyd's Register, the original electronic and certified version shall always prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Name and Address
Category
Grades
Sections
Bars
6082-T5, 6082-T6
6082-T5, 6082-T6
Max Thickness/Diameter
(mm)
Office
Australia
CAPRAL LIMITED
22.00
22.00
Melbourne
151, Barry Road
CAMPBELLFIELD
VIC 3061
Tel: +61 (0)3 9358 8138 Fax: +61 (0)3 9357 9952
Email to: [email protected] Web: http://www.capral.com.au
Certificate # MD00/4126/0001/6a Expiry date: 27/02/2016
Austria
AMAG ROLLING GmbH
Refining & Semi Finished 3003*
Plates
5083-H116, 5086-H116
5083-H321
Coils
3003-H14*
Vienna
63.50
76.20
7.00
A-5282 Ranshofen
P.O. 32
tel: +43 7722 801 3697 fax: +43 7722 809 511
E-Mail mailto:[email protected] Web http://www:amag.at
*Approved applications only.
Certificate # MD00/3189/0005/6a Expiry date: 17/09/2014
Belgium
SAPA RC PROFILES NV/SA
Kortemarkstraat 52.
BE-8810
Lichtervelde
Sections
6005A-T6, 6082-T6
10.00
Antwerp
Castings
Al-Si7Mg
75.00
Vancouver BC
Tel: +32 51 72 98 11 Fax: +32 51 72 54 41
Email: [email protected]
Web: http//:www.sapagroup.com
Certificate Number: MD00/3856/0002/6a Expiry date: 07/11/2016
Canada
HASTINGS BRASS FOUNDRY LTD.
236 Clark Drive
Vancouver, BC
V5L 3H3
Tel: +1 604 253 2811 Fax: +1 604 253 3133 Email to: [email protected]
Approval includes ASTM B26/B26M-12 Grade 356
Certificate Number: MD00/4325/0001/6a Expiry date: 28/05/2017
China, People's Republic of
ALERIS ALUMINUM (ZHENJIANG) Co., Ltd.
Refining & Semi Finished 5083, 5086
Plates
5083-O, 5083-H116, 5083-H112,
5086-H116
Nanjing
50.00
No. 1 Cai Jia Road,
Jing Kou Industrial Park
Zhenjiang, Jiangsu, 212141
Tel : +86 511 85307347
E-Mail : [email protected]
Web: http://www.aleris.com
Certificate #: MD00/4332/0001/6a
Expiry date: 06/06/2017
LONGKOU CONGLIN ALUMINUM CO., LTD.
Refining & Semi Finished Al-Mg-Si grades
Sections
6005A-T6, 6061-T6, 6082-T5, 6082-T6
555.00
43.00
Qingdao
Conglin Industry District
Longkou City
Shandong Province 265705
Tel: +86 535 8562517
Fax: +86 535 8563202
Certificate #: MD00/4430/0001/6a
Email to: [email protected]
Web: http://www.conglin.com.cn
Expiry date: 03/02/2018
Page
© Lloyd’s Register Group Limited 2015. All rights reserved.
2
As at 11 February 2015
This is a copy of an electronic document. In the event of any conflict or ambiguity between the copy and the electronic document,
which is retained and published by Lloyd's Register, the original electronic and certified version shall always prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Name and Address
Category
Grades
SOUTHWEST ALUMINIUM (GROUP) CO., LTD.
Plates
5083-O, 5754-O
5083-H321
5083-H112, 5754-H112
2618-T6
Forgings*
Max Thickness/Diameter
(mm)
Office
5.00
20.00
30.00
500.00
Wuhan
20.00
Prague
116.00
Prague
Xipeng
Jiou Long-po District,
Chongqing City
Chongqing City,
Grade 5754 plate is acceptable for approved applications not in direct contact with seawater,
*Accepted for approved applications. Note: Forgings supplied as blanks in the non-heat treated condition.
Tel: +86 (23) 65808767 Fax: +86 23 65808767
Email: [email protected]
web: www.cqswa.cn
Certificate #: MD00/2921/0005/6a Expiry date: 12/10/2017
Czech Republic
ALCAN STROJMETAL ALUMINIUM FORGING s.r.o.
Ringhofferova 66,
251 68 Kamenice
Forgings*
7022-T6, 2618A-T6
Castings
Al-Si10Mg
Tel: +420 204 672 302 Fax: +420 204 672 028
Certificate #: MD00/3898/0002/6a Expiry date: 23/03/2017
SLEVARNA A MODELARNA NOVE RANSKO, s.r.o.
Nove Ransko 234
582 63 †dírec nad Doubravou
Tel No +420 569 669 480 Fax No. +420 569 669 487
Email [email protected]
Web www.slevarna.cz
Certificate #: MD00/4186/0001/6a Expiry date: 23/06/2016
France
CONSTELLIUM FRANCE
Refining & Semi Finished Al-Mg grades
Plates
5086-H116, 5086-H321
5086-O, 5086-H111, 5086-H112
5083-H116
5383-H116, 5383-H321
5083-O, 5083-H111, 5083-H112,
5083-H321, 5383-O, 5383-H111,
5383-H112
Lyon
30.00
40.00
50.00
80.00
170.00
Flat Rolled Products
BP 42
63502 Issoire Cedex
Tel: +33 4 7355 5050
Fax: +33 4 7355 5090
Email: mailto:[email protected]
Materials Quality Scheme approved - MQS 037
Certificate #: MD00/1241/0009/6a Expiry date: 26/02/2016
FORGES DE BOLOGNE
39 rue des Forges
BP 82138 BOLONGE
52310 BOLOGNE
Tel: +33 3 25 32 80 13
Forgings*
7175-T6
220.00
Lyon
5083
200.00
Lyon
Fax: +33 3 25 32 39 21 Email to: [email protected]
Certificate #: MD00/4324/0001/6a Expiry date: 27/05/2017
L'UNION DES FORGERONS
12 Rue De La Pierre Follège
BP 16 - Z.A.
91660 Méréville
Forgings*
Tel: +33 (0) 1 64 95 02 25 Fax: +33 (0) 1 64 95 09 89
Email: mailto:[email protected]
Web: http://www.union-des-forgerons.fr
Certificate #: MD00/3229/0003/6a Expiry date: 24/03/2015
SABART SAS - Tarascon sur Ariege
Refining & Semi Finished 7175-O*
Page
© Lloyd’s Register Group Limited 2015. All rights reserved.
3
Marseille
As at 11 February 2015
This is a copy of an electronic document. In the event of any conflict or ambiguity between the copy and the electronic document,
which is retained and published by Lloyd's Register, the original electronic and certified version shall always prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Name and Address
Category
Grades
Max Thickness/Diameter
(mm)
Sections
6082-T6
130.00
Office
BP 29,
09400 Tarascon sur Ariege
Tel no: +33 561 024 004
Fax no: +33 561 024 011
Email [email protected]
Web:www.constellium.com
Certificate no. MD00/4351/0001/6a
Expiry Date 28/06/2017
Appproved supplier to Forges de Bologna
*7175 included in this scope of approval
* for approved appplications only
Germany
ALERIS EXTRUDED PRODUCTS GERMANY GMBH
WERK BITTERFELD
Devillestrasse 2
06749 Bitterfeld
Dortmund
Tel: +49 (0) 3493 75475 Fax: +49 (0) 3493 75477
Email: [email protected]
Web: http://www.aleris.com
Mechanical testing is carried out by approved test house.
Certificate: MD00/3781/0002/6a Expiry date: 27/04/2016
ALERIS EXTRUDED PRODUCTS GERMANY GMBH WERK BONN
Refining & Semi Finished Al-Mg-Si grades, Al-Mg grades
Sections
5083-O, 5083-H112, 5083-H321,
5086-O, 5086-H112, 5086-H321,
6082-T6
Bars
5083-O, 5083-H112, 5083-H321,
5086-O, 5086-H112, 5086-H321,
6082-T6
Dortmund
60.00
60.00
Friedrich Wöhler Straße 2
D-53117 Bonn
Tel: +49 (0) 228 558 2755 Fax: +49 (0) 228 558 2874 Email:mailto:[email protected]
Web:http://www.aleris.com
Including ingots with a maximum diameter of 400 mm.
Certificate No. MD00/1623/0007/6a Expiry date: 03/02/2016
ALERIS ROLLED PRODUCTS GERMANY GMBH
Refining & Semi Finished Al-Mg-Si grades, Al-Mg grades
Plates
5083-H116
5059-O, 5059 H111, 5059 H116, 5059
H321, 5083-O, 5083-H111,
5083-H112, 5083-H321, 5086-O,
5086-H112, 5086-H321, 6061-T6,
6082-T6
Sections
5083-O, 5083-H111, 5083-H112,
5083-H321, 5086-O, 5086-H112,
5086-H321, 6061-T6, 6082-T6
Bars
5083-O, 5083-H111, 5083-H112,
5083-H321, 5086-O, 5086-H112,
5086-H321, 6061-T6, 6082-T6
Dortmund
70.00
250.00
250.00
250.00
Carl-Spaeter-Straße 10
D-56070 Koblenz
Tel: +49 (0)261 891-7527 Fax: +49 (0)261 891 9 7527 Email: mailto:[email protected] Web:www.aleris.com
Certificate No. MD00/0697/0010/6a Expiry date: 19/04/2016
ALERIS ROLLED PRODUCTS GERMANY GmbH
Refining & Semi Finished All Grades
Dortmund
Schleusenstr. 11
D-46562 Voerde
Tel: +49 0281 9421 Fax: +49 0281 94212 26 Email: [email protected] Web http://www.voerdal.com
Approval is for round vertical cast billets 202 to 348 mm diameter, maximum weight 2000 Kgs for alloy's series 5xxx and 6xxx, also alloy's series 3xxx and 7xxx
for approved applications.
Certificate: MD00/3665/0003/6a Expiry date: 24/08/2015
ALUMINIUM WERKE GMBH VILLINGEN
Goldenbühlstraße 14
78048 Villingen-Schwenningen
Castings
Al-Si10Mg, AlSi7Mg0,3*, AlSi9Mg*
234.00
Hamburg
* For Approved Applications.
Tel: +49 7721 846031 Fax: +49 7721 846051
Email: mailto:[email protected]
Web : www.agvs.de
Certificate No. MD00/3355/0003/ 6a Expiry date: 13/07/2016
ALUMINIUMWERK UNNA AG
Refining & Semi Finished Al-Mg-Si grades, Al-Mg grades
Sections
5083-O, 5083-H111, 5083-H112,
5086-O, 5086-H111, 5754-O,
5754-H111, 6061-T5, 6061-T6,
6082-T5, 6082-T6
Bars
5083-O, 5083-H111, 5083-H112,
5086-O, 5086-H111, 5754-O,
5754-H111, 6061-T5, 6061-T6,
Page
© Lloyd’s Register Group Limited 2015. All rights reserved.
4
Dortmund
160.00
160.00
As at 11 February 2015
This is a copy of an electronic document. In the event of any conflict or ambiguity between the copy and the electronic document,
which is retained and published by Lloyd's Register, the original electronic and certified version shall always prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Name and Address
Category
Grades
Max Thickness/Diameter
(mm)
Office
Germany
6082-T5, 6082-T6
Uelzener Weg 36
D-59425 Unna
Includes approval for pipes and tubes with 250 mm outer diameter (max.) and 40 mm wall thickness (max).
Tel: +49 2303 206 148 Fax: +49 2303 206 117
Email: mailto:[email protected]
Web: http://www.alunnatubes.com
Certificate No. MD00/3152/0007/6a Expiry date: 16/03/2017
ANALYTIK NORD GmbH
Castings
Al-Mg3, Al-Si12, Al-Si10Mg,
Al-Si7Mg, Al-Si5Cu*, Al-Si9Cu*,
Al-Si(Cu)*
150.00
Hamburg
350.00
Hamburg
600.00
Dortmund
Hermannstrasse 35a
D-25421 Pinneberg
Tel: +49 4101 374 570 Fax: +49 4101 374 5719 email: mailto:[email protected] Web:http://www.analytiknord.de
Certificate No. MD00/2630/0005/6a Expiry date: 01/01/2015
C.F. MAIER LEICHTGUSSWERK GMBH & CO. KG
Königsbronn
Postfach 1165
D-89548 Königsbronn
Castings
Al-Si10Mg, Al-Si7Mg
Tel: +49 (0)7328 81152 Fax: +49 7328 81193 EMail: mailto:[email protected] Web http://www.c-f-maier.de
Certificate No. MD00/2037/0006/6a Expiry date: 12/07/2016
CONSTELLIUM SINGEN GmbH
Sections
5083-O, 5083-H111, 5083-H112,
5086-O, 5086-H111, 5086-H112,
6005A-T6, 6061-T6, 6082-T6
5083-O, 5083-H111, 5083-H112,
5086-O, 5086-H111, 5086-H112,
6005A-T6, 6061-T6, 6082-T6
Bars
600.00
Alusingen Platz 1
D-78224 Singen
Tel: +49 7731 80 2917 Fax: +49 7731 80 2224 Email: mailto:[email protected] Web:http://www.alcan-singen.com
Certificate No. MD00/2654/0005/6a Expiry date: 17/03/2015
HAL ALUMINIUMGUSS LEIPZIG GMBH
Gutenbergstraße 20
04178 Leipzig
Castings
Al-Si10Mg, Al-Si7Mg
510.00
Dortmund
10.00
Dortmund
10.00
Hamburg
Tel: +49 341 453 40 50 Fax: +49 341 453 40 90 Email: mailto:[email protected] Web: http://www.hal-gruppe.de
Certificate No. MD00/3363/0003/6a Expiry date: 01/08/2016
HYDRO ALUMINIUM ROLLED PRODUCTS GmbH
Coils
5083-O, 5083-H111, 5083-H112,
5083-H116, 5083-H321
Aluminiumstraße 1
D-41515 Grevenbroich
Tel: +49 (0)2181 66 1381 Fax: +49 (0)2181 661864
Email: [email protected]
Web: http://www.hydro.com
Certificate No. MD00/0095/0007/6a Expiry date: 20/01/2018
HYDRO ALUMINIUM ROLLED PRODUCTS GmbH
Plates
Coils
5083-H112, 5083-H321, 5086-O,
5086-H111, 5086-H112, 5086-H321
5083-O, 5083-H111
3003-O*, 3003-H111*
Castings
Al-Si10Mg, Al-Si7Mg
Castings
Al-Si7Mg
12.00
5.00
Aluminiumstraße
21129 Hamburg
Tel:- +49 (0)40 74011-417 Fax:- +49 (0)40 74011-244
EMail: mailto:[email protected]
Web: www.hydro-aluminium.com
Certificate No. MD00/2218/0008/6a Expiry date: 13/06/2016
METALLGIEßEREI GUTSCHERA GmbH
Industriestraße 4
D-59379 Selm
750.00
Dortmund
1200.00
Dortmund
Tel: +49 (0) 2592/1538 Fax: +49 (0) 2592/20826
Email:mailto:[email protected]
Web: http://www.gutschera.de
Certificate No. MD00/2269/0006/6a Expiry date: 19/11/2016
METALLGUSS SEIFERT GMBH
Boschstraße 8 - 10
D-56457 Westerburg / Sainscheid
Tel: 0049 (0) 2663 91540 Fax: 0049 (0) 2663 915429
Email:mail to: [email protected]
Web Page: www.metallguss-seifert.de
Certificate No. MD00/3449/0003/6a Expiry date: 20/11/2015
Page
© Lloyd’s Register Group Limited 2015. All rights reserved.
5
As at 11 February 2015
This is a copy of an electronic document. In the event of any conflict or ambiguity between the copy and the electronic document,
which is retained and published by Lloyd's Register, the original electronic and certified version shall always prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Max Thickness/Diameter
(mm)
Name and Address
Category
Grades
Metallgießerei an der Mulde GmbH
Castings
Al-Mg3, Al-Si12, Al-Si10Mg,
Al-Si7Mg, Al-Si5Cu*, Al-Si9Cu*,
Al-Si8Cu3*, Al-Si(Cu)*, Al-Cu4Ti*,
Al-Mg5(Si)*, Al-Zn10Si8Mg*,
Al-Zn15Si8*
Office
750.00
Dortmund
500.00
Dortmund
Muldenhütten
D-09627 Hilbersdorf
Tel: +49 (0) 3731 39690 Fax: +49 (0) 3731 39693 Email: mailto:[email protected]
* accepted for approved applications.
Certificate Number: MD00/2745/0004/6a Expiry: 05/10/2015
OHM & HÄNER METALLWERK GMBH & CO. KG
Web: http://www.m-adm.de
Castings
Al-Si10Mg, Al-Si7Mg, AlSi9Mg*
Im Grüntal 1
D-57462 Olpe
Tel: +49 02761/921-457 Fax: +49 02761/921-555
Email: mailto:[email protected]
Web:http://www.ohmundhaener.de
Certificate No. MD00/2257/0006/6a Expiry date: 25/09/2016
OTTO FUCHS KG
Refining & Semi Finished Al-Mg-Si grades, Al-Mg grades
Sections
5083-O, 5086-O, 6061-T6, 6082-T6
Bars
5083-O, 5086-O, 6061-T6, 6082-T6
Forgings*
5083-O, 5083-F, 5083-H321, 5086-O,
5086-F, 5086-H321, 6061-T6, 6082-T6
Dortmund
260.00
160.00
2000.00
Derschlager Straße 26
D-58540 Meinerzhagen
Tel. 49(0)2354 73 897 Fax 49(0)2354 73 201
EMail:[email protected]
Web page http://www.otto-fuchs.com
* accepted for approved applications
Certificate No. MD00/0553/0006/6a Expiry date: 06/03/2017
SECO GmbH
Castings
Al-Si12, Al-Si10Mg,
Al-Si12CuMgNi*
0.35
Dortmund
250.00
250.00
Dortmund
Gross Orden 23
D-06484 Quedlinburg
Tel: +49 (0) 3946 9079250 Fax: +49 (0) 3946 9079215
Email mailto: [email protected] Web http://www.secogmbh.de
Certificate #: MD00/3525/0003/6a Expiry date: 25/06/2017
WESERALU GmbH & Co. KG
Sections
Bars
6061-T6, 6082-T6
6061-T6, 6082-T6
Am Osthafen 5
D-32423 Minden
Tel +49 (0)571 38705 22
Fax +49 (0)571 38705 55
Certificate #: MD00/1664/0007/6a Expiry date: 12/08/2017
WIELAND-WERKE AG
Graf-Arco-Strasse 36
D-89079 Ulm
Email: mailto: [email protected]
Extrusions
Web:http://www.weseralu.de
Al-Mg-Si Grades
76.00
Hamburg
Tel: +49 731 944 2508 Fax: +49 731 944 4208 Email: [email protected] Web: http://www.wieland.de
The scope of approval is for extruded finned tubes only with a maximum 5mm wall thickness in grades AlMn1 and AlMgSi0.5 supplied in the as extruded
condition, accepted for approved applications.
Certificate Number: MD00/3216/0003/6a Expiry: 28/01/2015
Greece
ANOXAL S.A.
3rd km Inofita-Agios Thomas Road,
32011, Agios Thomas,
Viotia,
Refining & Semi Finished 6005A, 6061, 6082, Al-Mg-Si grades
230.00
Piraeus
5.00
40.00
Piraeus
Tel: +30 226 205 3569 Mob: +30 697 440 3569
email: [email protected]
Certificate No: MD00/4357/0001/6a Expiry date: 03/07/2017
Approval includes grades EN AW 6060 and 6063. Grades not covered by LR Rules are accepted for approved applications only.
COSMOS PROFIL S.A.
Sections
Bars
6082-T6
6082-T6
Page
© Lloyd’s Register Group Limited 2015. All rights reserved.
6
As at 11 February 2015
This is a copy of an electronic document. In the event of any conflict or ambiguity between the copy and the electronic document,
which is retained and published by Lloyd's Register, the original electronic and certified version shall always prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Name and Address
Category
Grades
Max Thickness/Diameter
(mm)
Office
8th km National Road Larissa - Athens,
Larissa,
Tel No: +30 2410 567567 Fax No: +30 2410 567510
Email: [email protected] or [email protected]
Web: www.cosmosaluminium.gr
Certificate No: MD00/4306/0001/6a Expiry Date 06/04/2017
Approval includes bars of square, rectangular, round and hexagonal shapes and section profiles of various shapes (flat or hollow) up to 5mm in thickness
Sections within Circumscribed Circle Diameter maximum 250mm x 5mm thickness.
Bars within Circumscribed Circle Diameter maximum 250mm x 40 mm thickness
ELVAL HELLENIC ALUMINIUM INDUSTRY S.A.
Plates
5083-O, 5083-H111, 5083-H116,
5083-H321, 5086-O, 5086-H111,
5086-H116
12.70
Piraeus
Refining & Semi Finished Al-Mg-Si grades, 3103*
203.00
Piraeus
Extrusions
5.00
130.00
Piraeus
57 km Athens Lamia National Road
GR-32011 Inofyta-Viotia
Tel: +30 22620 53600 Fax: +30 22620 31347
Email: mailto:[email protected]
Web: http://www.elval.gr
Certificate No. MD00/2990/0007/6a Expiry date: 02/09/2015
EPALME S.A.
Inofita, Viotia
32011
Tel: +30 22620 30806 Fax: +30 22620 56300
email: [email protected] Web http://www.epalme.gr
Certificate No. MD00/4303/0001/6a Expiry date: 02/04/2017
ETEM SA
6082-T5, 6082-T6
6005A-T6, 6005A-T5
1,Iroon Polytechniou Street
Magoula
19018
Tel: +30210 4898 525 Fax: +30210 4898510
email [email protected] Web http://www.etem.gr
Certificate No. MD00/3581/0003/6a Expiry date: 06/04/2015
India
HINDALCO INDUSTRIES LTD
Refining & Semi Finished Al-Mg-Si grades, Al-Mg grades
Plates
5083-O, 5083-H112, 5086-O,
6061-T6, 6082-T6
Sections
5083-O, 5083-H112, 5086-O,
5086-H112, 6061-T6, 6082-T5,
6082-T6
Bars
5083-O, 5083-H112, 5086-O,
5086-H112, 6061-T6, 6082-T5,
6082-T6
Calcutta
12.50
25.00
50.00
P.O. Renukoot
Dist. Sonbhadra 231217
Uttar Pradesh
Tel: +91 5446 252077-79 Fax: +91 5446 252107/252427
Email: mailto: [email protected]
Web: http://www.hindalco.com
Certificate No. MD00/0674/0007/6a Expiry date: 03/04/2016
VULKAN Technologies Pvt. Limited
Castings
Al-Si7Mg
Al-Si12, Al-Si10Mg
12.50
64.00
Mumbai
GAT No. 539B
Village Kasar Amboli
Pirangut Industrial Area, Tal-Mulashi
Dist. Pune 412115, Maharashtra
Tel: +91 20 6676 5541 Fax: +91 20 6676 5551 Email mailto:[email protected]
Certificate Number: MD00/3051/0005/6a Expiry: 20/01/2016
Page
© Lloyd’s Register Group Limited 2015. All rights reserved.
Web: http://www.vulkanindia.com
7
As at 11 February 2015
This is a copy of an electronic document. In the event of any conflict or ambiguity between the copy and the electronic document,
which is retained and published by Lloyd's Register, the original electronic and certified version shall always prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Name and Address
Category
Grades
Max Thickness/Diameter
(mm)
Office
Italy
ALCOA TRASFORMAZIONI S.r.l.
Refining & Semi Finished Al-Mg grades
Plates
5083-H128
5083-H116, 5083-H321
5083-O, 5083-H111, 5083-H112
Venice
8.00
40.00
60.00
Stabilimento di Fusina
Via dell' Elettronica 31
30176 Malcontenta
Loc. Fusina, Venezia
Tel: +39 041 2917254
Fax: +39 041 2917212
EMail mailto:[email protected] Web page http://www.alcoa.com
MATERIALS QUALITY SCHEME APPROVED - MQS 046
Certificate No. MD00/2605/0011/6a Expiry date: 14/06/2015
BODEGA G. & C. S.P.A.
Via Binda di Sopra 1
24034 Cisano Bergamasco (BG)
Sections
6082-T5, 6082-T6
50.00
Milan
Castings
Al-Si7Mg
90.00
Ravenna
Sections
6005A-T5, 6005A-T6, 6082-T5,
6082-T6
30.00
Milan
65.00
Venice
700.00
Kobe
Tel: +39 035 438366 Fax: +39 035 4382300 Email: mailto:[email protected]
web: http://www.bodega.it
Certificate No. MD00/3112/0004/6a Expiry date: 24/10/2016
F.A.M. S.r.l.
Via Pasolini, 38-39
48018 GRANAROLO FAENTINO (RA)
Tel +39 0546 41494 Fax +39 0546 41441 email:
[email protected] web: www.fonderiafam.com
Certificate No. MD00/3288/0004/6a Expiry date: 27/11/2015
METRA S.P.A.
Via Stacca, 1
25050 Rodengo Saiano
Brescia
Tel: +39 030 6819205 Fax: +39 030 6810260 Email: mailto:[email protected]
Certificate No. MD00/2975/0004/6a Expiry date: 05/05/2015
SA & BAR S.r.l
Via A. Boldrini, 26
Frazione Quarto Inferiore
40057 Granarolo Dell'Emilia (BO)
Web: http://www.metra.it
Castings
Al-Si7Mg
Castings
Al-Si12, Al-Si7Mg
Tel: +39 051 767022 Fax: +39 051 0547900
Certificate No. MD00/3949/0002/6a Expiry date: 18/09/2017
Japan
FUKUTATSU ALLOY MFG. CO., LTD.
15, 1, 3 - Chome
Takatsukadai
Nishi-ku
Kobe
Tel +81 78 991 2201 Fax +81 78 991 1523
Email mailto:[email protected]
Web: www.fukutatsu.com
Certificate No. MD00/0556/0006/6a Expiry date: 05/08/2016
KOBE STEEL LTD.
Refining & Semi Finished Al-Mg grades
Sections
5083-O, 5086-O, 5154A*
Bars
5083-O, 5086-O, 5154A*
Nagasaki
150.00
150.00
Chofu Plant
14-1, Minato-Machi
Chofu, Shimonoseki City,
Yamaguchi Pref. 752-0953
Tel: +81 83 246 1810 Fax: +81 83 346 1710
Email to:[email protected]
Web http://www.kobelco.co.jp
* accepted for approved applications
Certificate No. MD00/1947/0006/6a Expiry date: 11/11/2014
KOBE STEEL LTD.
Forgings*
5083-F
5083-O, 5083-H112
Page
© Lloyd’s Register Group Limited 2015. All rights reserved.
8
370.00
2055.00
Kobe
As at 11 February 2015
This is a copy of an electronic document. In the event of any conflict or ambiguity between the copy and the electronic document,
which is retained and published by Lloyd's Register, the original electronic and certified version shall always prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Name and Address
Category
Grades
Sections
5083-O, 5083-H112
Max Thickness/Diameter
(mm)
Office
Daian Plant
1100, Umedo
Daian-cho
Inabe-city
Mie-ken,
Tel: +81 594 77 2202 Fax: +81 594 77 2249
Email: [email protected]
* accepted for approved applications
Certificate No. MD00/2087/0009/6a Expiry date: 10/04/2017
LIGHT METALS EXTRUSION DEVELOPMENT CO., LTD.
2-2, 2 chome, Higashi Ogoso
Yokkaichi
Mie-ken
20.00
Kobe
420.00
Yokohama
1200.00
Kobe
300.00
Kobe
Tel: +81 593 45 4775 Fax: +81 593 47 0355 Email: mailto:[email protected]
Includes approval for pipes and tubes with 280mm outer diameter and 20mm wall thickness (max)
Certificate No. MD00/0930/0007/6a Expiry date: 02/06/2017
MIURA CO., LTD.
20-1 Kamitsuru, Aza
Imaizumi,
Sukagawa-city,
Fukushima 962- 0301
Castings
Al-Si7Mg
Castings
Al-Mg3, Al-Si12, Al-Si10Mg,
Al-Si7Mg
Forgings*
5083-O
Tel No: +81 248 76 2662 Fax No: +81 24876 2663
Email: [email protected]
Web: www.miura1.co.jp
Certificate No: MD00/4136/0001/6a
Expiry Date 02/04/2016
RYOSAN INDUSTRY CORPORATION
57 Eibara Nagao-cho
Kita-ku
Kobe
Tel: +81 (0)78 986 6617 Fax: +81 (0)78 986 4472
Email: mailto:[email protected]
Web: http://www.ryosan-ind.co.jp
Certificate No. MD00/1257/0007/6a Expiry date: 01/12/2017
SEO KOATSU KOGYO CO., LTD.
Ichikawa Works
869-20 Kanzaki Ichikawa-cho
Kanzaki-gun
Hyogo-pref
Tel: +81 790 28 0590 Fax: +81 790 28 1140
* accepted for approved applications
Certificate No. MD00/1338/0006/6a Expiry date: 11/11/2016
UACJ CORPORATION
Refining & Semi Finished Al-Mg grades
Plates
5083-H116
5083-O, 5083-H321
Yokohama
35.00
200.00
FUKAYA WORKS
1351, Uwanodai
Fukaya City
Saitama Pref.
366-8511
Tel +81 485 72 1316 Fax +81 485 73 5228
Email: [email protected]
Web http://www.uacj.co.jp
The scope of approval includes for the manufacture of alloy 3003 supplied to ASAHI CHEMICAL INDUSTRY CO. LTD for use for transition joints.
Certificate Number: MD00/1277/0009/6a Expiry: 11/03/2015
UACJ Corporation
Nagoya Works
3-1-12, Chitose
Minato-ku
Nagoya
455-8670
Plates
5083-O
160.00
Kobe
Sections
Bars
5083-O
5083-O
120.00
600.00
Kobe
Tel: +81 52 654 1186 Fax: +81 52 654 0039
Email: mailto:[email protected]_lm.co.jp
Web: http://www.sumitomo-lm.co.jp
Certificate No. MD00/1453/0007/6a Expiry date: 15/06/2015
UACJ Corporation
UACJ Extrusion Nagoya Corporation
Nagoya Works,
3-1-12 Chitose,
Minato-ku,
Nagoya 455-8670
Tel No: +81 52 654 1186 Fax no: +81 52 654 0039
Email: [email protected]_im.co.jp
Web: www.sumitomo_im.co.jp
Certificate No: MD00/4047/0003/6a Certificate Expiry 15/06/2015
Page
© Lloyd’s Register Group Limited 2015. All rights reserved.
9
As at 11 February 2015
This is a copy of an electronic document. In the event of any conflict or ambiguity between the copy and the electronic document,
which is retained and published by Lloyd's Register, the original electronic and certified version shall always prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Name and Address
Category
Grades
UACJ Corporation
Plates
3003-O**
5083-H321
5083-O
Max Thickness/Diameter
(mm)
15.00
80.00
200.00
Office
Kobe
Fukui Works
21-1 Kurome Mikuni-cho
Sakai City,
Fukui-Pref.,
913 - 8588
Tel No:
Email:
Web:
+81 776 82 5843
Fax No:
+81 776 82 5854
Materials Quality Scheme Approved - Approval No. MQS010
Certificate No: MD00/ 4230/ 0002/6a Expiry Date: 16/10/2015
* For thickness 29mm and above self annealing 5083 denoted as 5083(SA)
** accepted for approved applications only
UACJ Extrusion OYAMA Corporation
Refining & Semi Finished Al-Mg grades
Sections
5083-O
Bars
5083-O
Yokohama
20.00
200.00
560 Dotou
Oyama City,
Tochigi Pref.
323-0812
Tel no; +81 285 23 2113
Fax No: +81 285 25 0567
Email mailto: [email protected]
Web xxxxxxxxxxxxxxxx
Accepted for approved applications
Certificate No:MD00/4261/0009/6a Expiry date 15/0/2015
UACJ Foundry & Forging Corporation
Forgings*
2618-T6
5083-O
1000.00
2000.00
Yokohama
Forgings*
5083-O
100.00
Kobe
Sections
Bars
5083-O
5083-O
6061-T6
30.00
50.00
120.00
Changwon
Castings
Al-Si7Mg
50.00
Seoul
544.00
Ulsan
Foundry and Forging Works
560, Dotou,
Oyama City,
Tochigi 323-0812
Tel No: +81 285 24 3611
Fax +81 285 22 2884
Email mailto: takashima. [email protected] group.com
Web http://www.uaccj.co.jp
Certificate number MD00/4267/ 0001/6a
Expiry date 13/02/2015
YAMASHITA TANZOSHO CO., LTD.
43-1 Ikuno
6 Chome Katano
Osaka pref.
Tel: (0)72 891 1421 Fax (0)72 892 2126
* Accepted for approved applications
Certificate No. MD00/3249/0003/6a Expiry date: 22/07/2015
Korea
ALCOA KOREA Ltd.
54, Sungju-dong,
Sungsan-gu,
Changwon,
Gyeongnam,
Tel. +82 55 269-9585 Fax +82 55 269-9501
Web: http://alcoa.com/korea/en/home.asp
Certificate No. MD00/2078/0007/6a Expiry date: 01/04/2015
KOREA LOST-WAX CO., LTD.
#74, Gongdan 1-Daero 363 Beon-Gil,
Siheung-Si,
Gyeonggi-Do, 429-450
Tel: +82 31 499 8485 Fax: +82 31 431 6091
email: [email protected] web: www.lostwax.co.kr
Certificate No. MD00/2664/0004/6a Expiry date: 10/03/2017
* Investment castings in alloy A357 accepted for approved applications.
POONGSAN CORPORATION
Forgings*
2618-T6
Page
© Lloyd’s Register Group Limited 2015. All rights reserved.
10
As at 11 February 2015
This is a copy of an electronic document. In the event of any conflict or ambiguity between the copy and the electronic document,
which is retained and published by Lloyd's Register, the original electronic and certified version shall always prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Name and Address
Angang Plant
2222-2, Sandae-Ri
Angang-Oup
Kyungji-Si
Kyungbu
Angang-Oup
Kyungju-Si, Kyungbuk
Kyungju-Si, Kyungbuk
Category
Grades
Max Thickness/Diameter
(mm)
Office
Tel: +82 54 760 6692 Fax:P +82 54 760 6690 Email: mailto:[email protected]
* For Approved Applications
Certificate No. MD00/3250/0004/6a Expiry date: 25/07/2015
New Zealand
FLETCHER ALUMINIUM
30-32 Bowden Road
Mt Wellington
Extrusions
6061-T5, 6061-T6
190.00
Auckland
250.00
Auckland
Tel: +64 09 574 1500 Fax: +64 09 573 0418 email: [email protected] Web: http://:www.fletcheraluminium.co.nz
Certificate No. MD00/3077/0004/6a Expiry date: 07/04/2016
ULLEXCO
Extrusions
6061-T5, 6061-T6, 6082-T5, 6082-T6,
6005A-T6, 6261-T6*, 6005A-T5,
6261-T5*
A Division of Ullrich Aluminium
39-45 Maui Street
Pukete Industrial Estate
Hamilton
Tel: +64 (07) 849 5095 Fax: +64 (07) 849 4453 Email mailto:[email protected] Web: http://www.ulrich-aluminium.co.nz
* accepted for approved applications.
Certificate Number: MD00/3071/0004/6a Expiry: 06/03/2016
Norway
ALCOA MOSJØEN AS
8655 Mosjøen
Refining & Semi Finished 5083, 5086
Oslo
Tel: +47 751 79100 Fax: +47 751 71887 Email: mailto:[email protected]
Web: http://www.alcoa.com
Approval for semi finished products covers rolling ingots to 630mm max thickness, 2930mm max width and 8600mm max length.
Certificate No. MD00/3358/0003/6a Expiry date: 21/07/2016
BENTELER ALUMINIUM SYSTEMS NORWAY AS
Fabrikkveien
Cast House, Building 123,
2830 Raufoss
Refining & Semi Finished Al-Mg-Si grades
305.00
Oslo
20.00
Oslo
405.00
Stavanger
Tel: +47 81 15 60 00 Fax: +47 61 15 94 87
web: www.benteler.com
Certificate No: MD00/3995/0002/6a Expiry date: 19/10/2017
HYDAL ALUMINIUM PROFILER AS
Sections
6005A-T4*, 6005A-T6, 6061-T6,
6082-T4*, 6082-T6
Raufoss Industripark,
Fabrikkveien, Bygn. No. 232 (vestsiden),
N-2830 Raufoss
Tel: +47 61 15 30 00 Fax: +47 61 15 3062 Email mailto:[email protected] Web: www.hydro.com
Certificate No. MD00/3054/0007/6a Expiry date: 29/01/2016
HYDRO ALUMINIUM A.S. KARMØY
Hydroveien 160
4265 HÅVIK
Refining & Semi Finished Al-Mg-Si grades
Tel no: +47 528 54000 Fax no: +47 528 54380 Mob +47 48028973
Email [email protected]
Web: www.hydro.com
Certificate No: MD00/4328/0001/6a
Expiry date 28/05/2017
Approval includes SFP ingot up to 405mm diameter x 7000mm in length
mechanical testing out sourced
Page
© Lloyd’s Register Group Limited 2015. All rights reserved.
11
As at 11 February 2015
This is a copy of an electronic document. In the event of any conflict or ambiguity between the copy and the electronic document,
which is retained and published by Lloyd's Register, the original electronic and certified version shall always prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Name and Address
Category
Grades
Max Thickness/Diameter
(mm)
Forgings*
7022-T6
7.60
Katowice
40.00
Moscow
Office
Poland
ZAKLAD OBROBKI PLASTYCZNEJ Sp. z o.o.
ul. Kuznicza 13
21- 045 Swidnik
Tel No: +48 81 7515008 Fax No: +48 81 4680911 Mob No: +48 504204770
Email: [email protected] or [email protected]
Web: www.kuznia-zop.pl
Certificate no: MD00/4313/0001/6a Expiry date: 01/05/2017
*For Approved Applications
Raw material supply restricted to Grupa Kety SA.
Russia
J.S.C. KAMENSK URALSKY METALLURGICAL WORKS
Plates
5083-O, 5083-H111, 5086-O,
5086-H111, 5754-O, 5754-H111
6061-T6, 6082-T6
6061-T5, 6061-T6, 6082-T5, 6082-T6
5083-O, 5086-O, 5754-O
6005A-T5, 6005A-T6, 6061-T5,
6061-T6, 6082-T5, 6082-T6
Sections
Bars
76.00
330.00
250.00
406.00
KUMW J.S.Co.
5, Zavodskaya St
Kamensk Uralsky
Sverdlovsk Region
623405 Russia
Tel: +7 3439 395 145 Fax: +7 3439 395 068
Email: mailto:[email protected]
Web: http://www.kumz.ru
Certificate No. MD00/2917/0004/6a Expiry date: 30/09/2014
South Africa
HULAMIN LIMITED
Refining & Semi Finished 5083, 5086, 6061, 6082
Plates
5083-O, 5083-H116, 5083-H112,
5083-H321, 5086-O, 5086-H112,
6061-T6, 6082-T6
5083-H111
Sections
5083-O, 5086-O, 6061-T6, 6082-T6
Durban
25.00
30.00
190.00
(Rolled Products)
Moses Mabhida Road
Pietermaritzburg
3200
Tel: +33 396 6911 Fax +33 395 6469 Email mailto:[email protected] Web http://www.hulamin.co.za
Certificate No. MD00/3277/0006/6a Expiry: 11/10/2015
Sweden
SAPA PROFILER AB
Sections
Bars
6082-T6
6082-T6
30.00
70.00
Stockholm
Box 72
S-612 22 Finspång
Tel: +46 (0)122 795090
Email: mailto:[email protected]
Web:http://www.sapagroup.com
Certificate No. MD00/1270/0006/6a Expiry date: 21/03/2015
SAPA PROFILER AB
Refining & Semi Finished Al-Mg-Si grades
Sections
6082-T6
Bars
6082-T6
Gothenburg
30.00
30.00
Remelt / Press P2
Sjunnen Works SE-574 81
SE- 57481 Vetlanda
Tel: +46 383 94169 Fax: +46 383 15435
Email: [email protected] Web: http://www.sapagroup.com
Certificate Number: MD00/3422/0004/6a Expiry date: 28/01/2017
Approval covers for semi finished products as vertically cast ingots up to 317mm diameter and nominal 7000mm length supplied in the homogenised condition.
Approval for sections does not include closed profile sections.
Page
© Lloyd’s Register Group Limited 2015. All rights reserved.
12
As at 11 February 2015
This is a copy of an electronic document. In the event of any conflict or ambiguity between the copy and the electronic document,
which is retained and published by Lloyd's Register, the original electronic and certified version shall always prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Name and Address
Category
Grades
Max Thickness/Diameter
(mm)
Office
Switzerland
ALU MENZIKEN EXTRUSION AG
Refining & Semi Finished 3003*
Extrusions
3003-O*
307.00
30.00
Dortmund
Hauptstrasse 35
CH-5737 Menziken
Tel: +41 62 765 29 07 Fax: +41 62 765 27 47
Email :[email protected]
Web: www.alu-menziken.com
Certificate No. MD00/3325/0003/6a Expiry date: 10/03/2016
CONSTELLIUM VALAIS SA
Refining & Semi Finished Al-Mg grades, Al-Si grades
Plates
5083-H321, 5086-H321
5083-O, 5083-H111, 5083-H112,
5086-O, 5086-H111, 5086-H112,
6061-T6, 6082-T6
Sections
5083-O, 5083-H111, 5083-H112,
5086-O, 5086-H111, 5086-H112
6005A-T6, 6061-T6, 6082-T6
Bars
5083-O, 5083-H111, 5083-H112,
5086-O, 5086-H111, 5086-H112
6061-T6, 6082-T6
Hamburg
8.00
150.00
600.00
720.00
600.00
720.00
PO Box
CH 3960 Sierre
Tel: +41 27 457 67 70
Email: [email protected]
Web: www.constellium.com
Certificate No. MD00/2608/0006/6a Expiry date: 03/08/2017
The Netherlands
NEDAL ALUMINIUM B.V.
Sections
Bars
6005A-T6, 6061-T6, 6082-T6
6005A-T6, 6061-T6, 6082-T6
50.00
50.00
Amsterdam
6082-T6
63.00
Newcastle upon Tyne
25.00
Southampton
P.O. Box 2020
3500 GA Utrecht
Tel: +31 302925819 Fax: +31 302939512 Email: [email protected]
Web: www.nedal.nl
Certificate No. MD00/3429/0003/6a Expiry date: 23/06/2015
United Kingdom
SAPA EXTRUSIONS UK
Birtley Plant
Durham Road
Birtley
Chester-le-Street
County Durham, DH3 2AH
Extrusions
Tel: +44 (0)191 301 1226 Fax: +44 (0)191 301 1234 Email: [email protected] Website: www.sapagroup.com
Certificate No. MD00/3832/0003/6a
Expiry date: 21/09/2016
SAPA EXTRUSIONS UK
Bedwas Plant
Pantglas Industrial Estate
Bedwas
CF83 8DR
Sections
6082-T6
Tel: +44 (0)29 2085 4600 Fax: +44 (0)29 2086 5229 Email: [email protected] Web: www.sapagroup.com
Certificate No.: MD00/3848/0002/6a Expiry Date: 13/10/2016
SAPA PROFILES UK LTD.
Refining & Semi Finished Al-Mg-Si grades
Sections
6005A-T5, 6005A-T6, 6061-T5,
6061-T6, 6082-T5, 6082-T6
6005A-T5, 6005A-T6, 6061-T5,
6061-T6, 6082-T5, 6082-T6
Bars
Coventry (UK Ind.
Operations)
25.00
75.00
Tibshelf Plant
Sawpit Lane
Tibshelf
Derbyshire DE55 5NH
Tel: +44 1773 549296
Email: [email protected]
Web: http://www.sapagroup.com
Certificate No. MD00/1261/0008/6a Expiry date: 07/09/2017
Page
© Lloyd’s Register Group Limited 2015. All rights reserved.
13
As at 11 February 2015
This is a copy of an electronic document. In the event of any conflict or ambiguity between the copy and the electronic document,
which is retained and published by Lloyd's Register, the original electronic and certified version shall always prevail.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Name and Address
Max Thickness/Diameter
(mm)
Category
Grades
Office
Castings
Al-Si7Mg
1800.00
Chicago
Castings
Al-Si7Mg
73.00
Vancouver BC
United States of America
A & B FOUNDRY AND MACHINING LLC.
N 835 Main Street,
Franklin OH,
45005,
Tel: +1 937-746-3634 Fax: +1 937-736-3635
email: [email protected] web: www.abfoundry.com
Certificate No: MD00/4090/0001/6a Expiry Date: 08/11/2015
NU-CAST, INC.
29, Grenier Field Road,
Londonderry,
NH 03053
Tel No +1 603 432 1600
Fax No +1 603 432 0724
Email [email protected]
Web www. nu-cast.com
Certificate No MD00/ 3986/ 0001/6a
Expiry Date 08/02/2015
Page
© Lloyd’s Register Group Limited 2015. All rights reserved.
14
As at 11 February 2015
This is a copy of an electronic document. In the event of any conflict or ambiguity between the copy and the electronic document,
which is retained and published by Lloyd's Register, the original electronic and certified version shall always prevail.
Lloyd's Register Group Limited, its affiliates and subsidiaries and their respective
officers, employees or agents are, individually and collectively, referred to in this
clause as ‘Lloyd's Register’. Lloyd's Register assumes no responsibility and shall
not be liable to any person for any loss, damage or expense caused by reliance on
the information or advice in this document or howsoever provided, unless that
person has signed a contract with the relevant Lloyd's Register entity for the
provision of this information or advice and in that case any responsibility or liability
is exclusively on the terms and conditions set out in that contract.
© Lloyd’s Register Group Limited 2015. All rights reserved.
© Lloyd’s Register Group Limited 2015. All rights reserved.
This is a copy of an electronic document. In the event of any conflict or ambiguity between the copy and the electronic document,
which is retained and published by Lloyd's Register, the original electronic and certified version shall always prevail.