PARTS LIST SOLENOID VALVE ASSEMBLY

PARTS LIST
||||||||||||||||||||||||||||||||||||||||||||||||||||||||
||||||
||||||
| | | | | | | | | | | | | | | | | ||||||||| || | | | | | | | | | | | | | || ||| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | || || || | | | | | | |
| | | | | ||| | | | || | |
||||| |
||||| ||||
|
|||| | | | | | | | |
|||
|||||||||||||
|||||||||||
||||||||
|| |
|||||
||
| ||||
||
||||
|||||||||||||
||| | | | |
|||||||
|||||
| | | | | | || | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | ||||||||||||||||||||||||||||||
|||||||
| | | | | | | | | ||||||
|||||
| | || || | | | |
|
| || || | |
|
||
|||||||||||
|| | |
||||||||
| | | | | | | | | | || | | | | | | | | | | | | | | | | | | | | |
|||||||||||
|||||||||||||| | | | | | | |
| | | | | | | | | | | | | | | | ||| || | | | | | | | | | | | | | | | | | | | | | | | || | | | | | | | | | | | | | | | | | | | | | | | | | |
| | ||||||||||||
| | || | | | | |
||||||||||
| | |||||||
Solenoid Valve Assembly Water and Data
• Identify and locate water & power sources, ideally
within several feet of each other. Refer to the System
Layout.
|||| |
| | | | | | | | | | | | | | | | | | || | | | | | | | | |
||
|
||||
| | | | | | | | | ||||
| |||||||
BEFORE YOU START
| | | || | | | | | | |
| | | || ||| | | | | | | | | | | | | | || || || || | | | | |
|||| | |
||||
SYSTEM LAYOUT
|||
Water Data
Cable Assembly
Bowl Data &
Quick Discon-
• Identify the bowl location.
NOTE: The bowl must be no more than 12 feet from
the water and power sources.
MAX DISTANCE: 4'
• We provide three options for installation. You will
ONLY use one.
Bowl
Solenoid Valve
Assembly (SVA)
MAX DISTANCE: 12'
Optional Installs
Single kit,
two configuration options
(supplied)
90° Elbows
3/8” Faucet
Adapter
1/2” Faucet
Adapter
Power Supply &
SVA Power Plug
Tie Wraps
& Mounts
||||||||||||||||||||||||||||||||||||||||
Existing
Water
Supply
||||||||||||
|||||||||
|||||||
||||||
|||||
|||||
||||
||||
||||
||
||||
||||||
|||||
||||
||||
Standard Install
Kit 1/4” Polyethylene*
• If you have any questions, please check our website for
additional information, or contact your favorite handy
person.
Water Filter
*Polyethylene is a rigid plastic tubing, typically known as ‘ice maker line’.
SOLENOID VALVE ASSEMBLY MOUNTING
INSTALLATION KITS
• NOTE: We provide three options for installation. You
will ONLY use one.
Data Jack
• For Standard Install - 1/4” Polyethylene* Accessory
Line, refer to Standard Install.
Water Filter Inlet
• For Optional Install - 3/8” Compression Fittings, refer
to Optional Install 1.
Power Jack Solenoid Valve
Outlet
2. One easy way to accomplish this is to use the enclosed
8” Tie Wrap and adhesive backed Tie Wrap Mount.
OPTIONAL INSTALL 1
1/4” Polyethylene Accessory Supply Line
Faucet Adapter - 3/8” Compression
Configuration
NOTE: We provide three options for installation. You will ONLY
use one. This page is typical for 1/4” water line hookup.
NOTE: We provide three options for installation. You will ONLY
use one.
Existing
Water
Line
• For Optional Install - 1/2” Pipe Thread Fittings, refer
to Optional Install 2.
*Polyethylene is a rigid plastic tubing, typically known
as ‘ice maker line’.
1. Mount Solenoid Valve Assembly such that the
four access points to the water, power, and data
connections are maintained.
STANDARD INSTALL
1. Locate a convenient spot to tap into your
1/4” Polyethylene Accessory Supply Line. It
should be within 5’ of where you mounted the
Solenoid Valve Assembly. Refer to the System
Layout.
2. Turn off Water Source. Carefully cut the
Supply Line with a razor blade or scissors.
Make the cut as perpendicular as possible to
the Supply Line. Insert each cut end into the
opposed ends of the ‘T’ fitting, pressing firmly
until they bottom out.
3. Using the 5’ piece of tubing provided, insert
one end into the Shutoff Valve and the other
end into the Water Filter Inlet, pressing firmly
until they bottom out. You may use the entire
5’ of tubing or cut it if desired.
The piece
of tubing
between
Shutoff
Valve and
Filter may
be up to
5 feet long.
1. Turn off the Water Source to the faucet.
2. Using a wrench, loosen and remove the
Cold Water Supply Line from the Water
Source.
3. Install the Brass Fitting on the right side
of the Faucet Adapter as shown and
tighten with wrenches.
4. Install the Faucet Adapter onto the Water
Source and tighten with a wrench.
5. Install the Cold Water Supply Line to
the Faucet Adapter and tighten with a The piece of tubing
between Shutoff
wrench.
Valve and Filter may
6. Using the 5’ piece of tubing provided, be up to
insert one end into the Shutoff Valve and 5 feet long.
the other end into the Water Filter Inlet,
pressing firmly until they bottom out. You may use the entire 5’
of tubing or cut it if desired.
7. Proceed with Water/Data Cable Assembly - Bowl Connections.
OPTIONAL INSTALL 2
WATER/DATA CABLE ASSEMBLY - BOWL
Faucet Adapter - 1/2” Pipe Thread Configuration
NOTE: We provide three options for installation. You will ONLY
use one.
1. Turn off the Water Source to the faucet.
2. Using a wrench, loosen and remove the
Cold Water Supply Line from the Water
Source.
3. Install the Brass Fitting on the left side
of the Faucet Adapter as shown and
tighten with wrenches.
4. Install the Faucet Adapter onto the Water
Source and tighten with a wrench.
5. Install the Cold Water Supply Line to
the Faucet Adapter and tighten with a The piece of tubing
between Shutoff
wrench.
Valve and Filter may
6. Using the 5’ piece of tubing provided, be up to
insert one end into the Shutoff Valve and 5 feet long.
the other end into the Water Filter Inlet,
pressing firmly until they bottom out. You may use the entire 5’
of tubing or cut it if desired.
7. Proceed with Water/Data Cable Assembly - Bowl Connections.
PRESSURIZING THE WATER SYSTEM
1. Turn on the Water Source.
Standard Install Kit:
1/4" Polyethylene
Optional Install Kit:
3/8” Compression
Connections to Bowl
1. Place the bowl in desired
location, upside down.
• NOTE: We provide three options for installation. You
will ONLY use one.
2. Set your Shutoff Valve to approximately 45° as
indicated above.
3. Verify all connections remain dry.
4. Insert SVA Power Plug from Power Supply into
Power Jack on the Solenoid
Valve Assembly.
Safely route the Water/Data Cable Assembly from the
Bowl to the Solenoid Valve Assembly.
In cable locations prone to accidental impact - cabinet
toe kick area, pot and pan cabinet storage, cleaning
supply under sink storage - be sure to securely locate
Water/Data Cable Assembly against a wall or shelf
where the cable cannot be disturbed.
2. Insert the
Data Plug
into the
Data Jack.
3. Secure the
Quick Disconnect
Coupler to the
Quick Disconnect
Insert.
One option provided is the Tie Wraps and Tie Wrap
Mounts.
No kinks in the water line:
• Avoid bending the Water/Data Cable Assembly too
sharply.
4. To separate the Quick
Disconnect, press release button
with your fingertip. Valves
in both sides will
close to prevent
leakage.
• If a sharp bend is required:
– S eparate the Water Line from the Split Wrap
Tubing where the bend is required.
–C
ut the tubing and install one of the 90° Elbows
provided.
–D
o NOT cut the Data Cable.
ACTIVATING THE BOWL
1. Plug Wall Mount Power Supply into a regular 120 volt
outlet.
Optional Install Kit:
1/2” Pipe
ROUTING THE
WATER/DATA CABLE ASSEMBLY
LEDS
LED Indications
Condition
Red LED
Green LED
2. Use the Shutoff Valve to adjust
the water pressure as shown
to the right.
Power Off
Off
Off
Power On
On
Off
Water Off
On
Off
3. The water pressure shown here
is too low. The water is barely
coming out.
Water On
On
On
Auto Learn
On
Flashing
Auto Learn Error
Flashing
On
Power Outage Error
Flashing
Off
Timeout Error
Flashing
Flashing
3
4. The water pressure shown here
is too high. The water is splashing
against the opposite wall of the
bowl.
5. The water pressure shown here
is set properly. The water drops
down midway across the bowl.
4
5
WATER/DATA CABLE ASSEMBLY - SVA
Connections To Solenoid Valve Assembly
1. After routing the Water/
Data Cable Assembly from
the Bowl to the Solenoid
Valve Assembly, remove the
protective cap from the Water
Line.
2. Insert the Water Line into the
Solenoid Valve Outlet,
denoted by the tip of
the arrow on the white
plastic part of the
Solenoid Valve.
3. Insert the Data Plug
into the Data Jack.
The Data Jack
and Power
Jack are
different
and cannot
be mixed up.