1. business and industrial
2. energy
3. oil

(Brick Stencilled Concrete)
ABN 35 051 984 993
The Beauty
of Brick...
The Strength
o f C o n c re t e !
The Ultimate In Decorative
Concrete Systems
Adding style to your home
is the Australian Slate-Crete
way.
Now the grace and elegance
of brick, tile and stone can
be enjoyed for a fraction
of
its
traditional
cost.
BRICK-Crete has
the
strength and durability of
concrete with the beauty and
charm of old world masonry
craftsmanship.
With well over 1 million square
metres laid annually, BRICKCRETE is a proven winner
with homeowners, builders,
developers, architects and
councils alike.
Any
qualified
concrete
contractor can use BRICKCRETE, so demand it by
name...
BRICK-CRETE the ultimate
in decorative concrete.
www.australianslate-crete.com.au
HERRINGBONE / MARIGOLD
We at Australian SlateCrete Supplies have
developed a unique,
specially formulated
product, with a
difference.
A PRODUCT THAT:
• Providesexcellent results in hot
and cold conditions.
• Providesone product for all
finishes.
• Prevents premature wearing.
Whether you are
looking for:
• Slate Finished Concrete
• Textured Brick Stencilled Concrete
• Pattern Paving
RUNNINGBOND/BRICK RED
EUROPEAN FAN/BEIGE
• or just plain coloured Concrete
with over 30 exciting colours to choose
from, we have something for you.
Whether installing decorative concrete
for domestic or commercial purposes,
an Australian Slate-Crete™ product
will beautify your environment and
enhance the value of your property.
Advantages:
• Exceptionally hard wearing surface
• No more weeds
• C
ost effective (one product for all finishes)
• E
xciting colours to beautify your project
• A
finish that is stronger than
concrete itself
• Slip resistant
• Non fading colours
• Low maintenance
OCTAGON TILE/TERRA RED
Application:
• Driveways
• Paths
• Patios
• Roadway
• Public thoroughfares
• o
r anywhere there is a need for concrete
Australian Slate-Crete™ Supplies
– Quality of Product, Quality of
Service, Export Quality.
BASKETWEAVE/MARIGOLD
HERRINGBONE/GREY
Displays
HERRINGBONE (Stencil) GREY
EUROPEAN FAN (Stencil) SALMON
10” REGAL (Stencil) BURNT RED
265mm TILE (Stencil) MARIGOLD
COBBLE BRICK EDGE & TILE EDGE (Stencil)
16” REGAL (Stencil) GREY
COBBLE STONE (Stencil) BLUESTONE
RANDOM BLUESTONE (Stencil) MARIGOLD
RUNNING BOND (Stencil) DARK CORAL
RUNNING BOND (Stencil) TERRA COTTA
COBBLE FAN (Stencil) TAN
HERRINGBONE (Stencil) BRICK RED
BUSH ROCK EDGE & BRICK EDGE (Stencil)
10” REGAL (Stencil) BLUESTONE
BUSHROCK (Stencil) TAN
8” TILE (Stencil) MARIGOLD
8" TILE/SANDSTONE
HERRINGBONE/BRICKRED
BUSHROCK/FAUN
w w w. a u s t r a l i a n s l a t e - c r e t e . c o m . a u
Displays
HERRINGBONE (Stencil) TERRA RED
8” TILE (Stencil) TERRA COTTA
10” REGAL (Stencil)TAN
RANDOM BLUESTONE (Stencil) BLUESTONE
COBBLE BRICK (Stencil) CHARCOAL
BUSH ROCK (Stencil) LIGHT BROWN
265mm TILE (Stencil) SALMON
8” TILE (Stencil) BUFF
CONVICT ROCK (Stencil) BLUESTONE
COBBLE BRICK (Stencil) BURGUNDY
265mm TILE (Stencil) SLATE GREEN
CONVICT ROCK EDGE &
SOLDIER COURSE (Stencil)
RUNNING BOND (Stencil) FAUN
COBBLESTONE (Stencil) BURNT RED
BASKETWEAVE (Stencil) CHOC BROWN
ROSETTES
RUNNINGBOND/TERRA COTTA
265MM TILE/BLUESTONE
BUSHROCK/CHARCOAL
w w w. a u s t r a l i a n s l a t e - c r e t e . c o m . a u
Stencil Patterns
RUNNING BOND
BASKET WEAVE
8” (200mm) TILE
10” (250mm) REGAL
Brick Size 195 x 100mm
Brick Size 200 x 90mm
Tile Size 200 x 200mm
Paver Size 265 x 145mm
265 TILE
HERRINGBONE
BRUSHROCK
16” (400mm) REGAL
Tile Size 265 x 265mm
Brick Size 195 x 90mm
Average Size 230 x 90mm
Paver Size 400 x 215mm
COBBLESTONE
CONVICT ROCK
COBBLE BRICK
EUROPEAN FAN
Average Size 187 x 140mm
Average Size 197 x 140mm
Average Brick Size 230 x 140mm
Average Size 100 x 130mm
COBBLE FAN
RANDOM BLUESTONE
OCTAGON TILE
Average Size 130 x 130mm
Average Size 195 x 140mm
Brick Size 200 x 200mm
ROSETTE (Brick)
.9m, 1.4m, 1.6m, 2.0m & 2.2m
ROSETTE (Cobble)
STAR COMPASS
DIAMOND
0.9m, 1.6m & 2.2m
0.9m & 1.6m
1.25m
SOLDIER COURSE
CONVICT ROCK EDGE
TILE EDGE
Brick Size 200 x 100mm
Average Size 160 x 187mm
195 x 200mm
BRUSHROCK EDGE
BRICK EDGE
COBBLE BRICK EDGE
Average Size 160 x 187mm
Brick Size 225 x 100mm
Average Size 200 x 125mm
w w w. a u s t r a l i a n s l a t e - c r e t e . c o m . a u
Colour Chart
SLATE-CRETE ™ (Slate finished concrete)
BRICK-CRETE ™ (Brick stencilled concrete)
AUSTSPRAY-ON-CRETE (Texture on existing concrete)
ABN 35 051 984 993
SANDSTONE
Hardener......
TERRACOTTA Hardener, RELEASE
PEACH
Hardener......
LIGHT GREEN
Hardener......
BUFF
Hardener......
TERRA RED
Hardener, RELEASE
SALMON
Hardener......
SLATE GREEN
Hardener......
ALMOND
Hardener......
BURNT RED
Hardener......
MARIGOLD
YELLOW
Hardener......
BRICK RED
Hardener......
LIGHT BROWN Hardener, RELEASE
BEIGE
CARAMEL
Hardener......
DARK CORAL
Hardener......
CHOC BROWN Hardener, RELEASE
FAUN
KHAKI
Hardener......
BURGUNDY
Hardener, RELEASE
DARK BROWN Hardener, RELEASE
TAN
OFF WHITE
Hardener......
BLUESTONE
Hardener, RELEASE
CHARCOAL
BLACK
Hardener, RELEASE
GREY
Hardener, RELEASE
Hardener, RELEASE
Hardener, RELEASE
DARK GREEN Hardener, RELEASE
Hardener......
Hardener, RELEASE
Hardener......
IMPORTANT
The sample colours illustrated are simulated to match the actual
product as close as modern printing methods will allow. Some
variation in shading may occur, depending on the job conditions and
finishing practices utilised by your concrete contractor.
BLUE GUM
Hardener......
w w w. a u s t r a l i a n s l a t e - c r e t e . c o m . a u
1. The concrete is poured to a
minimum thickness of 100mm.
A paper stencil is then laid on
top of the concrete.
2. Colour Hardener is then applied
to the surface of the concrete
and trowelled in.
3. After the concrete has been
left to dry sufficiently, the paper
stencil is removed to reveal the
required pattern.
4. Finally, a sealer is applied
to protect the surface from
staining and to give you an
attractive and durable finish.
AUSTRALIAN SLATE CRETE SEALERS – HOW TO SEAL
FIRST TIME SEALING CONCRETE
RESEALING CONCRETE
SURFACE PREPARATION
SURFACE PREPARATION
It is very important to clean new concrete before applying an A.S.C. sealer. The
best method is to high pressure water blast (>1500 Psi) to remove concrete salts
(efflorescence) and dust, dirt and contaminants. On smooth concrete and hardened
surfaces it is also necessary to acid etch the surface to improve surface porosity
(absorption). A mixture of up to 1 litre of Hydrochloric Acid to 10 litres of clean water
is broomed over concrete to etch the surface. Thoroughly flush the surface with 1 part
A.S.C. Concrete Degreaser to 80 parts water to neutralise the acid solution, then rinse
well with water. Surface must be completely dry before sealing.
Prior to resealing it is important to thoroughly clean existing concrete to remove
oil, grease, dirt and contaminants. This can be achieved by using an A.S.C.
Concrete Degreaser in conjunction with a high pressure water blaster (>1500Psi)
and acid if required. Then allow to dry thoroughly.
APPLICATION – New or unsealed concrete
• Whilst the solvent is softening the second area, go back to the first, and with a
First Coat • Dilute the first coat by 15-25% using an A.S.C. Solvent to assist penetration into
the concrete. Stir thoroughly.
NOTE: During the warmer months, where the surface temperature is hotter,
additional solvent may need to be added to the sealer to assist penetration.
• Apply first coat evenly by broom or roller at a rate of approx. 4-7m2 per litre.
On very porous concrete diluting of the first coat may not be required.
Second Coat • Ensure the first coat has dried before resealing.
• A llow a minimum of 1 hour between coats in hot weather and considerably longer
in cold weather. For best results allow 24 hours between coats.
• A pply second coat neat or slightly diluted using A.S.C. Solvent (approx. 5%), by
broom or roller ensuring the application is as even as possible. In hot weather
more solvent may need to be added.
• It is recommended that the addition of one pack of A.S.C. Slip Resistant Powder
per 20 litres of sealer (stir well), will reduce slipping and improve pedestrian
safety. The Slip Resistant Powder will slightly thicken the sealer. Dilute with
A.S.C. Solvent to suite. The sealing of very steep and smooth concrete is NOT
recommended.
Difficult Areas For old concrete surfaces that have never been sealed, but have been contaminated
with oil, the following steps are required before sealer can be applied.
• Dilute 1 litre of A.S.C. Degreaser to 10 litres of water and apply to concrete floor
and scrub floor with a broom to soften any oil and dirt.
• Pressure clean concrete floor with water blaster (>1500Psi), to wash away residue.
• If concrete floors are clean then follow steps “New or Unsealed Concrete”
• For hard to remove oil or grease in concrete (eg. Garage floors) apply generous
amounts of A.S.C. Solvent to the area, and by scrubbing well, this will soften most
oil and grease. Immediately apply A.S.C. Concrete Degreaser (full strength) onto
affected area, scrub in then use high water pressure blaster to remove oil residue.
If clean then follow steps for “New or Unsealed Concrete”
WHEN AND WHEN NOT TO SEAL
Do not apply Sealer early morning or late in the day, as a risk of damage caused by
moisture, condensation and dampness increases. A.S.C. sealer affected by moisture
can lose gloss and adhesion properties and may turn milky in appearance. In
hot weather the first coat of sealer may be applied the day after it is poured.
However during winter, the concrete surface can remain damp longer, therefore we
recommend early afternoon sealing to ensure maximum dryness.
Note: If salting (Efflorescence) occurs, do not seal. Wash area thoroughly with water.
Allow to dry, then seal if no salt appears. If salt reappears then repeat the process.
Beware: Chalking or dusty concrete surfaces should not be sealed. If sealed you risk
the sealer peeling. Further information contact Australian State-Crete Supplies.
Maintenance: To keep your concrete surface looking its best we recommend that
every 5-6 months you scrub the surface with A.S.C Concrete Degreaser (see label
for dilution with water) and water pressure blaster if you have one.
Note: You cannot keep recoating the surface indefinitely with sealer. After 5-6 coatings
the sealer may need to be stripped with the new sealer process to start all over again.
APPLICATION
• Apply A.S.C Solvent to the sealed surface in approx. 1 metre x 1 metre square.
• Before working solvent into the surface apply solvent to the next section.
broom, start scrubbing the surface. Whilst scrubbing, the sealer will soften and
become tacky. Broom enough solvent onto the sealer to ensure that you have
softened all layers of the sealer, back to the bare concrete surface.
• The next section is ready to be worked on, but before you do, again apply
solvent.
• Repeat this process until all the sealer has been worked on. When surface
becomes touch dry you can then apply a coat of sealer. This process is
recommended to ensure maximum adhesion.
Note: Before resealing old existing sealer, which has good adhesion, the
compatibility of the two coatings should be tested in an area.
For very old sealer with problem or delaminating surfaces, (which may appear
milky in colour) the surface should be thoroughly scrubbed with A.S.C. Solvent at
least 24 hours prior to resealing. (See above)
Note: It is recommended before sealing that a small area be tested using this
method and left to weather for at least 4-6 weeks. If the test area fails, that is if
it discolours and again appears milky in appearance, then the sealer will have to
be removed. You will then need to apply a Sealer Stripper to remove the problem
sealer. Once all sealer has been removed then follow the procedures for “New or
Unsealed Concrete”. (See over page).
If there are no sealer problems then follow procedures for “Resealing Concrete”
(See above).
APPLICATION
Sealer can be applied by a soft bristle broom, roller or sprayer. If use sprayer
we recommend brooming immediately after spraying for evenness and to assist
penetration.
CURING TIME
Curing time is dependant on temperature. At 25 Degrees Celsius an A.S.C. Sealer
will touch dry in approx. 20 minutes. Allow a minimum of 1 hour between coats
in hot weather and considerably longer in cooler weather. The colder the weather
the longer you wait to reseal. For the best results allow 24 hours between coats.
Full curing time will be achieved within 7 days at ambient temperature. Avoid
parking vehicles for several days in cold weather and 3-4 days in very hot weather.
DO NOT park vehicles, with hot tyres, on freshly sealed concrete for at least 7 days.
TYRE MARKS
To remove black tyre marks from the sealer surface, apply a generous amount
of A.S.C. Solvent to the tyre marks. Broom or brush the affected area until the
sealer becomes tacky. With a cloth, lightly wipe the tyre mark from the sealer.
Apply more A.S.C. Solvent to the surrounding area to even out the softened
sealer. Reseal same area if necessary.
SAFETY DIRECTIONS
Please ensure adequate ventilation and avoid breathing vapours. Do not use
Australlian Slate-Crete Supplies Concrete and Paver Sealer whilst smoking
or near naked light or flame. Remove all non-canned foods from the area if
adequate ventilation is not possible during application or drying.
AVOID CONTACT WITH SKIN OR EYES
Should irritation occur please seek Medical advice.
w w w. a u s t r a l i a n s l a t e - c r e t e . c o m . a u
P ro d uct
I nformation
Colour Hardener (20kg Bag)
Coverage Approx. 10sqm per 20kg bag
Strength In the vicinity of 93MPa strength after 28 days.
Colours 30 exciting colours from gentle pastel to strong
earthy colours to choose from. Only the best
oxides available are used.
Same Day Seal A special formulated sealer (UV stable), which
can be applied to fresh concrete. Enhances curing and protects
job from early marking. Ideal as a first coat, with later sealing by
either Standard Gloss, HiGloss or Hard Seal Sealers.
Coloured Sealer
S
ealer specially tinted to match A.S.C.
colour chart.
Visual Effect The ability to create excellent mouldings for
slate and beautiful scratch finish for stencil.
Packaging 4 litre, 10 litre, or 20 litre drums.
Clear – 20 litre drum approx. 80m2
Conditions Provides excellent results in hot and cold
conditions.
Coverage Colour Sealer – 20 litre drum approx. 80m2
Flexibility The first genuine quality multi purpose product
on the market. No need to store different
products for different finishes. One product for
all finishes.
ACRYLIC SEALERS
Standard Gloss (Clear) To enhance the appearance and protect
concrete from oil, grease, dirt and weather. Recommended two
coats for all finishes. (UV stable)
Cleaning Sealer can be removed from tools and
equipment by using A.S.C. Solvent.
Note: If efflorescence (salting) occurs Do Not Seal, wash
thoroughly, allow to dry, then seal if no salt reappears.
Slip Resistant Powder – 300grms: For all smooth trowelled
concrete surfaces, we strongly recommend that A.S.C. Slip
Resistant powder be added to the sealer. This will aid in reducing
the slip factor.
HiGloss Regular strength sealer (UV stable) with a high gloss
finish, ideal on all concrete finishes.
Hard Seal A superior strength high gloss sealer, which is more
abrasive resistant, ideal for heavy traffic and vehicular areas. Is
UV stable and is ideal for all concrete finishes, even in a marine
environment.
Note: Hard Seal & Hi Gloss Sealers can only be applied to a cured
surface, or used as a second coat.
Epping Store
12 Yale Drive
Epping Victoria 3076
Ph: 61 3 9408 7722
Fax:61 3 9408 9034
Narre Warren Store
Unit 11, 4-6 Len Thomas Place
Narre Warren Victoria 3805
Ph: 61 3 9705 7766
Fax:61 3 8790 1299
w w w. a u s t r a l i a n s l a t e - c r e t e . c o m . a u