1. No category

PRO Grain Extractor
Manufactured by Arc Alloy Welding (1984)
Colonsay, Sask. S0K 0Z0
www.arcalloy.ca
Owner’s Guide to Use
1610 Model
Safety Warnings
NOTE:
Before operating extractor, familiarize yourself with all safety decals
and their locations on the PRO Extractor.
IMPORTANT SAFETY WARNING
Roller handle
Roller handle is NOT detented
DO NOT use bungee cord to hold handle
Refer to our website www.arcalloy.ca for extractor video
Set up Instructions
Set up Extractor
1. Attach the tractor draw bar to the extractor hitch with 1 1/8” draw pin. Hook up safety chains.
2. Attach the PTO and make sure it is locked.
3. Connect hydraulic hoses. Lift extractor high enough to remove transport stop (Image 1) and
replace with 3” stop (Image 2).
4. Lift the support leg (image 3) up and pin in temporary position (image 3A). Release the
transport pin (image 4) that holds bag roller and swing roller into working position.
5. Replace the support leg and pin the bag roller in place (image 5).
6. Pivot the bag knife (image 6) from the storage position to the operating position shown in
(image 7). Pin in place.
7. Raise the top of the auger into working position.
Image 1
Image 3
Image 2
Image 3A
.
Image 4
Image 6
Roller transport pin
Roller pin
Image 7
Image 5
Installing the bag onto PRO Grain Extractor
1. To begin make a horizontal cut just before the grain in the loose part of the bag. Then cut
towards the tractor from the horizontal cut splitting the bag down the center. Do not cut the
part of the bag that is under tension. See dwg 1
2. Back extractor up to the end of the bag with the bag between the wheels and cross augers are
inside the bag. The main auger should go into the cut in the top of the bag.
3. Make sure the roller is stationary and hooks are toward the bag. Starting from the center
of the bag, hook the bag onto the roller. Ensure all personnel are well clear of the roller.
Rotate the roller one or more turns until bag is completely wrapped around the roller.
4. Lower the extractor on to 3” stop (image 2). The cross auger should be approximately 3” off
the ground.
dwg 1
Image 2
Extracting the grain
1
Roll up the bag until cross augers are into the grain. The cutting knife should line up with
the cut in the top of the bag.
2
Ensure the unloading auger is lifted into position and the grain truck/cart is in position
ready to load. After first making sure the tractor is in neutral, slowly engage the PTO.
Once augers are engaged start the bag roller, adjust roller speed so cross augers stay full of
grain.
3
PTO speed can be increased to 540 once grain is flowing.
Removing the bag from the Extractor
1
To remove the bag from the roller, raise the extractor into transport position. Rotate the
handles on the roller drive plate until they disengage. See image 12
2
Slowly drive the tractor and extractor forward until the bag is fully unrolled.
Image 12
Notes:
Raise and lower upper auger at least three times to pump hydraulic cylinder.
1
7
13
10
2
13
12
4&8
6
10
13 3 & 8
9
11
Parts list—see following pages for part numbers and descriptions
Extractor Parts list
# 1 Main Drive
Part #
SA208-24
F208
8820L PWL
80BB12H3/4NTL
H80 1 rl
H80cl & H80os
242 26726-35R
Description
208-24 bearing locking collar 1 1/2"
208-4-bolt flange
sprocket #80 x 20 tooth
Idler sprocket # 80
#80 heavy chain
#H80 connector & off set link
Large PTO
# 2 Main drive line
SA208-24
F208
5018 1 1/2" NTL
5018 1 3/8" NTL
5018 2 rl chain
208-24 bearing locking collar 1 1/2"
208-2-bolt flange
Sprocket 50 x 18 tooth
Sprocket 50 x 18 tooth
Double roller chain #50
# 3 Lower Auger Drive
ST4190-11L
ST4190-11T
5018 1 1/2"
5018 1 3/8"
5018 2rl chain
50cl & 50os
ZEL059
ZEL060
90* gear box
"T" gear box
Sprocket 50 x 18 tooth
sprocket 50 x 17 tooth
Double roller chain #50
50 connector & off set link
1 1/2" x 25 1/4" shaft
1 1/2" x 22 5/8" shaft
# 4 Cross Auger Drive
3500 Series or 8 series
903-10355
PTO
1 3/8" -6 spline pump adapter
# 5 Lower auger flighting drive
Part #
H80Q23
Q1 2
H80P14
P 1 1/2
2" UHMW rod
H80 Chain
UCHA210-200D1LLJ
F210D
SA208-24
F208
Description
#80 Q 23 tooth sprocket
2" dia taper lock type hub
#80P14 tooth sprocket
Taper lock type hub
2" nylon chain tightner
#80 chain 40" long
Bearing special - NTN triple seal
Flange 210D ductile
Bearing 208-24 lock collar
F208 flange 4 bolt
Part #
Description
# 6 Main auger hangar bearing
KML-UCHA 210-32
Bearing with hangar type flange
# 7 Main auger top bearing
SA207-20
F207
# 8 Cross auger drive
SA207-20
PF207
60B25HF 1 1/4"
60B15HF 1 1/4"
60 1 rl chain 29"
207-20 bearing 1 1/4"
207- 4 bolt flange
RH 9" x 9" x 1-7/8 x 3/16
LH9" x 9" x 1-7/8 x 3/16
207-20 bearing 1 1/4
207 flangettes for 2" bearing
#60 - 25 tooth sprocket
#60 - 15 tooth sprocket
#60 chain
1/4" x 2" roll pin
Right hand flighting 5' long
Left hand flighting 5' long
# 9 Cross auger bearing
SA206-20
FL206
206-20 (1 1/4") bearing
206 - 2 bolt flange
# 10 Roller drive & bearings
SA210-32
F210D SPE3499
Q1 2 NTL
210 - 32 bearing 2"
210 - 4 bolt flange ductile
Split taper bushing
# 11 Roller Chain Drive
H50B13F 1" kw2SS
#50 1 rl chain 50"
50B70F
H50B15F 1 1/2" kw 2SS
#50 1 rl chain 61"
H60B13F 1 1/2" kw 2ss
60B96X2PB-brg 2"
#60 1 rl chain 90 3/4"
#60 cl & #60 os
S210-A113
HA220-1
50B13 1" hole
#50 reg chain
50B70 1 1/2" hole
50B15 1 1/2" hole
#50 reg chain
60B13 1 1/2" hole
60B96 2" hole
#60 reg chain
#60 connector & off set link
Spindle
Hub and caps
# 12 Axle
Part #
42655UC1
R50642
ST235-80/R16
Description
Hub
#42 Spindle
Tires
# 13 Misc
Q45-4E-FISN
F1020-S
BMR50-H4CS
40AGU08-10HYS
25 AGU24-10
F52-140080
S1018D
S1018J
2" x 5' strap c/w hook
4 Bank valve
Flow control
Motor
4X8 Cylinder
2 1/2 X 24 Cylinder
8K topwind dropleg jack
1/2" plug
1 1/4" plug
Roller straps
# 14 Hoses
T2SN6C20FJ90CFJC
T2SN6C118FJCFJ45C
T2SN6C124FJCFJ45C
T2SN6C110FJCFJC
T2SN6C82FJCFJC
T2SN8C240MPDFJ90D
T2SN6C48FJCFJC
20" Hose
118" Hose
124" Hose
110" Hose
82" Hose
240" Hose
48" Hose
Lower & upper auger flighting
14OD x 14 pitchx 3 1/2ID x 1/4 ga Flighting Length 74" lower
Roller drive cover
44-09602
44-09802
Adjustable cover center latch 6.4"
Striker for 44-09602