1. science
2. weather

Product Data Sheet
MOORSHIELD® NANO
THERMO/ COOL ELASTIC PAINT
503
Thermo insulating, high reflective elastic paint based on
innovative Nanotechnology. Uses new technology reflecting
and heat insulating microspheres. The special formulation of
the paint provides energy savings of the building. It has
specifications as a Cool Paint. Provides a breathable, mildew
resistant film. It has exceptional weather and UV resistant
properties.
Performance Features
•
•
•
•
•
Thermo insulating high reflective paint based on innovative
Nanotechnology.
It provides heat insulation and waterproofing using new technology
reflecting microspheres.
Provides energy savings of the buildings.
Excellent weather and UV resistant properties.
Provides a breathable, mildew resistant film.
Colors : White and Pastel Base which offers over 1.200 pastel
and medium colors available from the Moor-O-Matic Color
System.
Toxicity: Formulated without lead or mercury
Gloss Level: 0 - 3 at 60o viewing angle.
FLAT
I
0
GLOSS
I
3
I
100
THERMO INSULATING PROPERTIES
Thermal Conductivity
0,12 W / (mK) ISO 8302 (EN 12664 : 2004)
Solar Reflectance (SR)
0,87 (ASTM E 903-96 & ASTN G 159-98)
Infrared Emittance
0,84 ± 2% (ASTM E 408-71)
Solar Reflectance Index (SRI)
109 (ASTM E 1980-01)
Above measurements are verified by the National & Kapodestrian University of Athens, Physics Faculty and the Centre of Renewable
Energy Sources and Saving (C.R.E.S.) certifying that 503 MOORSHIELD NANO Thermo/Cool Paint is in category Cool Paint.
Performance Guide:
Weather Resistance
Excellent resistance to weather.
Environmental Resistance
Good resistance to concrete carbonation
Water Resistance
Excellent resistance to rain and condensation.
Abrasion Resistance
Fair resistance to abrasion.
VOC (Volatile Organic Compounds): 503 MOORSHIELD NANO Thermo/Cool Elastic Paint : belongs to the category A/c WB
(exterior walls of mineral substrate) is under the EU VOC Limits of: 40g/l (2010).
Spreading Rate
Weight Solids
Wet Film Thickness
Dry Film Thickness
8-9 m²/L per coat
65%
125 micrometres
69 micrometres
Dry Time at 20°C
Flexibility
Thinning
For Application By
1 hour to touch
5-6 hours to recoat
Passes 6 mm mandrel
Thin 5% with water
Brush, Roller , Spray
Surface Preparation
Surface to be painted must be free of all loose material such as flaking and peeling paint, dust, dirt, concrete salts and heavy chalk. The
surface must be clean with all traces of grease, oil, form oils and mildew removed. Remove loose material by scraping and sanding. Sand
glossy surfaces to a dull finish. Apply 2 or 3 coats 503 MOORSHIELD NANO after priming as outlined below.
New Concrete and Plaster: Prime with 182 SUPER SPEC. Stabilizing Primer or 181 SUPER SPEC Acrylic Alkali- Resisting Primer, thinned
according to label directions. Unpainted and Weathered Concrete, Brick: Prime with one coat of 182 SUPER SPEC Stabilizing Primer
thinned according to label directions. Previously Painted Surfaces: Prime with 182 SUPER SPEC or 192 Aqua Grip Micronized Primer.
New wood: Prime with 570 MOORESTYLE Alkyd Multi- primer or 023 FRESH START.
Application
Stir paint thoroughly before use. Apply by roller, brush, or airless spray. Thin 5% with clean water. Do not apply at temperatures below 10OC.
Drying: Dries in 1 hour. Recoat in 5-6 hours. Drying times are longer under cool/moist conditions.
Clean Up:
Clean equipment in warm, soapy water.
Precautions Health and Safety:
• Skin contact: Wash skin thoroughly with soap and water. • Eye contact: Treat immediately with water.• Get medical
attention.• If swallowed: Get medical attention without delay. • For further information, see the Health and Safety
Data Sheet for this product. • Keep out of reach of children. • Protect from freezing.
Packaging and Storage
Sizes :
1 litre, 3 litres, 10 litres
Flash Point:
none
Storage:
not hazardous, no special requirements
For Advising – Technical Services call: 2106620713-5, [email protected]