1. technology and computing
2. hardware

Area Lighting Poles
Phone: (866) 474-7200 • Fax: (817) 924-7049
American Lite Pole reserves the right to change any portion of this publication without notice in order
to promote product improvement and allow for material availability.
10
Area Lighting Poles
Design
The selection of the correct pole design is predicated on the specific loading requirements of each application. The poles
located in the steel pole chart are designed to withstand dead loads and theoretical dynamic loads developed by sustained
winds of 80 MPH through 100 MPH times the 1.3 gust factor. The combined EPA and the weight of the luminaire, light support brackets, and any other attachments cannot exceed the rated EPA or allowable weight on that pole.
Welding
All welds shall be of the highest quality and performed by American Welding Society certified welders conforming to the
latest version of the American Welding Society specification AWS D1.1.
Finish
All poles and mounting brackets are furnished with a coating of either red oxide/zinc primer, factory painted, powder coated
or hot-dip galvanized in accordance with ASTM A-123. Miscellaneous hardware will be galvanized to ASTM A-153. Exterior
finish top-coatings are available by request.
Ordering Logic
RTS - 30 - 90 - 11 - AB - PCDB - DM28 - BC
Height
Wall Thick
10 = 10 ft
20 = 20 ft
30 = 30 ft
Etc...
11 = 0.1196 in
7 = 0.1793 in
3 = 0.2391 in
G
PC
GP
P
-
Base Dia.
66 = 6.6 in
70 = 7.0 in
90 = 9.0 in
Etc...
Options
Finish
Galvanized
Powder Coat
Galvanized & Paint
Primed
Colors
DB = Dark Bronze
BL = Black
WH = White
GR = Gray
SP = Special
BC
SBC
NC
FES
DMP
=
=
=
=
=
Base Cover (Plastic)
Base Cover (Steel)
Nut Covers
Festoon Box
Vibration Damper
Base Design
AB
DE
LAB
= Anchor Base
= Embedded
= Less Anchor Bolts
Fixture Mount
Series
RTS
RNS
SNS
STS
SNSHG
STSHG
-
Round Tapered Steel
Round Non-tapered Steel
Square Non-tapered Steel
Square Tapered Steel
Square Non-tapered Steel (Hinged)
Square Tapered Steel (Hinged)
DM19
DM28
DM32
DM39
DM49
T20R
T25R
T30R
-
Drill One @ 90°
Drill Two @ 180°
Drill Three @ 120°
Drill Three @ 90°
Drill Four @ 90°
Tenon Round 2⅜ O.D.
Tenon Round 2⅞ O.D.
Tenon Round 3½ O.D.
Custom designs and aluminum poles are also available.
Please contact factory for details.
11
Phone: (866) 474-7200 • Fax: (817) 924-7049
American Lite Pole reserves the right to change any portion of this publication without notice in order
to promote product improvement and allow for material availability.
Area Lighting Poles - Round Tapered
Base
Pole
Bolt
Weight
Shaft
Plate
Height
Guage
Circle
(lbs)
Size (in) Width
(ft)
Dia. (in)
(in)
Catalog
Number
Anchor Bolts
(in)
Max Loading Capacities
80 (mph) 90 (mph) 100 (mph)
Dia x Len x Hook
Projection EPA Wt. EPA Wt. EPA Wt.
min / max (ft2) (lbs) (ft2) (lbs) (ft2) (lbs)
RTS-20-65-11-AB
20
160
11
6.5 x 3.7
10.5
9.0 - 10.0
1 x 36 x 4
4.75 / 5.75 24.2 605 19.3 482 15.6 390
RTS-25-59-11-AB
25
155
11
5.9 x 2.4
10
8.5 - 9.5
1 x 36 x 4
4.75 / 5.75 12.5 312
RTS-25-70-11-AB
25
200
11
7.0 x 3.5
11
9.5 - 10.5
1 x 36 x 4
4.75 / 5.75 20.3 507 16.2 405 13.1 327
RTS-30-66-11-AB
30
200
11
6.6 x 2.4
10.5
9.0 - 10.0
1 x 36 x 4
4.75 / 5.75 11.7 292
RTS-30-80-11-AB
30
265
11
8.0 x 3.8
11.5 10.5 - 11.5
1 x 36 x 4
4.75 / 5.75 18.9 472 14.9 373 12.0 300
RTS-35-85-11-AB
35
315
11
8.5 x 3.6
12
11 - 12
1 x 36 x 4
4.75 / 5.75 18.9 472 15.1 377 12.2 305
RTS-39-90-11-AB
39
355
11
9.0 x 3.5
12.5
12 - 13
1 x 36 x 4
4.75 / 5.75 17.2 430 13.5 338 10.8 270
RTS-39-90-7-AB
39
515
7
9.0 x 3.5
12.5
12 - 13
1.25 x 42 x 6
5.50 / 6.50 28.5 715 23.0 575 19.0 475
9.9
9.3
247
232
8.0
7.5
200
187
Pole Shaft
The pole shall be a one section design fabricated from standard 11 gauge (0.1196”) or 7 gauge (0.1793”) steel. Each section
shall be fabricated from high strength low alloy steel conforming to ASTM A-572, with minimum yield strength of 55,000 psi. Each
pole will have a full-length longitudinal weld and will be cylindrical in cross-section having a uniform taper rate of 0.14” of diameter
change per foot of length.
Base Plate
The base plate is fabricated from a structural quality hot rolled carbon steel plate that meets or exceeds ASTM A-36 with a minimum yield of strength of 36,000 psi. The base plate telescopes the pole shaft and is circumferential welded top and bottom. The
base plate has slotted bolt holes.
Hand Hole
A reinforced hand hole, having a nominal 3” x 5” or 4” x 6.5” opening, will be installed 18” above the base plate on all poles. A hand
hole cover and attaching hardware is included with each hand hole assembly. A ground lug will be welded either on the hand hole
frame or on the inside of the pole opposite the hand hole depending on the design.
Anchor Bolts
Anchor bolts are fabricated from a commercial quality hot rolled carbon steel bar that meets or exceeds minimum yield strength
of 55,000 psi. Anchor bolts are sized according to each pole design and are furnished with 2 galvanized heavy hex nuts and 2
galvanized flat washers. Anchor bolts shall be galvanized a minimum of 4” on the threaded end in accordance with ASTM A-153.
Anchor bolts will ship with the poles unless otherwise specified.
Pole Top
Each pole will be provided with either a removable pole cap or 2-3/8” O.D. x 4” tenon top (other sizes available).
Welding
All welds shall be of the highest quality and performed by American Welding Society certified welders conforming to the latest
version of the American Welding Society specification AWS D1.1.
Finish
All poles, mounting brackets and platforms are furnished with a coating of either red oxide/zinc primer, factory painted, powder
coated or hot-dip galvanized to ASTM A-123. Miscellaneous hardware will be galvanized to ASTM A-153. Exterior finish coatings
are available by request.
Note
Anchor bolt patterns are subject to change. Please consult factory prior to construction.
Bolt Circle
Anchor Bolt
Projection
Width
Base Plate
Slotted
Holes
Base Detail
Phone: (866) 474-7200 • Fax: (817) 924-7049
American Lite Pole reserves the right to change any portion of this publication without notice in order
to promote product improvement and allow for material availability.
12
Area Lighting Poles - Round Non-Tapered
Catalog
Number
Base
Pole
Bolt
Weight
Shaft
Plate
Height
Guage
Circle
(lbs)
Size (in) Diameter
(ft)
Dia. (in)
(in)
Anchor Bolts
(in)
Max Loading Capacities
80 (mph) 90 (mph) 100 (mph)
Dia x Len x Hook
Projection EPA Wt. EPA Wt. EPA Wt.
min / max (ft2) (lbs) (ft2) (lbs) (ft2) (lbs)
RNS-10-40-11-AB
10
70
11
4.0
10.5
7.0 - 9.0
0.75 x 17 x 3
4.00 / 5.00 19.1 480 15.0 375 12.2 305
RNS-15-40-11-AB
15
100
11
4.0
10.5
7.0 - 9.0
0.75 x 17 x 3
4.00 / 5.00 9.6
250
7.4
185
5.9
150
RNS-20-40-11-AB
20
120
11
4.0
10.5
7.0 - 9.0
0.75 x 17 x 3
4.00 / 5.00 6.0
150
4.5
150
3.5
125
RNS-25-40-11-AB
25
145
11
4.0
10.5
7.0 - 9.0
0.75 x 17 x 3
4.00 / 5.00 2.9
100
2.0
75
1.4
75
RNS-25-50-11-AB
25
180
11
5.0
10.5
7.0 - 9.0
0.75 x 17 x 3
4.00 / 5.00 7.3
180
5.5
150
4.3
150
RNS-25-50-7-AB
25
260
7
5.0
10.5
7.0 - 9.0
0.75 x 17 x 3
4.00 / 5.00 12.1 300
9.4
250
7.5
200
RNS-30-50-11-AB
30
210
11
5.0
10.5
7.0 - 9.0
0.75 x 17 x 3
4.00 / 5.00 4.2
150
3.0
125
2.3
100
RNS-30-50-7-AB
30
305
7
5.0
10.5
7.0 - 9.0
0.75 x 17 x 3
4.00 / 5.00 8.0
200
6.5
160
4.8
125
Pole
ole Shaft
The
he pole shall be a one section design fabricated from standard 11 gauge (0.1196”) or 7 gauge (0.1793”) steel. Each section shall
be
e fabricated from high strength low alloy steel conforming to ASTM A
A-500
500 grade B
B, with minimum yield strength of 42
42,000
000 psi
psi. Each
pole will have a full-length longitudinal weld and will be cylindrical in cross-section.
Base Plate
The base plate is fabricated from a structural quality hot rolled carbon steel plate that meets or exceeds ASTM A-36 with a minimum
yield of strength of 36,000 psi. The base plate telescopes the pole shaft and is circumferential welded top and bottom. The base
plate has slotted bolt holes.
Hand Hole
A reinforced hand hole, having a nominal 2.5” x 5” opening, will be installed 18” above the base plate on all poles. A hand hole cover
and attaching hardware is included with each hand hole assembly. A ground lug will be welded either on the hand hole frame or on
the inside of the pole opposite the hand hole depending on the design.
Anchor Bolts
Anchor bolts are fabricated from a commercial quality hot rolled carbon steel bar that meets or exceeds minimum yield strength of
55,000 psi. Anchor bolts are sized according to each pole design and are furnished with 2 galvanized heavy hex nuts and 2 galvanized flat washers. Anchor bolts shall be galvanized a minimum of 4” on the threaded end in accordance with ASTM A-153. Anchor
bolts will ship with the poles unless otherwise specified.
Pole Top
Each pole will be provided with either a removable pole cap or 2-3/8” O.D. x 4” tenon top (other sizes available).
Welding
All welds shall be of the highest quality and performed by American Welding Society certified welders conforming to the latest version of the American Welding Society specification AWS D1.1.
Finish
All poles, mounting brackets and platforms are furnished with a coating of either red oxide/zinc primer, factory painted, powder
coated or hot-dip galvanized to ASTM A-123. Miscellaneous hardware will be galvanized to ASTM A-153. Exterior finish coatings
are available by request.
Note
Anchor bolt patterns are subject to change. Please consult factory prior to construction.
Anchor Bolt
Bolt Circle
Projection
Width
Slotted
Holes
Base Plate
13
Base Detail
Phone: (866) 474-7200 • Fax: (817) 924-7049
American Lite Pole reserves the right to change any portion of this publication without notice in order
to promote product improvement and allow for material availability.
Area Lighting Poles - Square Non-Tapered
Catalog
Number
Base
Pole
Bolt
Weight
Shaft
Plate
Height
Guage
Circle
(lbs)
Size (in) Width
(ft)
Dia. (in)
(in)
Anchor Bolts
(in)
Dia x Len x Hook
Max Loading Capacities
80 (mph) 90 (mph) 100 (mph)
Projection EPA Wt. EPA Wt. EPA Wt.
min / max (ft2) (lbs) (ft2) (lbs) (ft2) (lbs)
SNS-10-40-11-AB
10
75
11
4.0
8.25
8.0 - 9.0
0.75 x 17 x 3
4.00 / 5.00 30.6 765 23.8 595 18.9 472
SNS-15-40-11-AB
15
115
11
4.0
8.25
8.0 - 9.0
0.75 x 17 x 3
4.00 / 5.00 17.2 430 13.2 330 10.0 250
SNS-20-40-11-AB
20
140
11
4.0
8.25
8.0 - 9.0
0.75 x 17 x 3
4.00 / 5.00 9.6
167
4.5
112
SNS-20-40-7-AB
20
185
7
4.0
8.25
8.0 - 9.0
0.75 x 17 x 3
4.00 / 5.00 15.0 375 11.0 275
9.0
225
SNS-20-50-11-AB
20
185
11
5.0
11
10 - 12
0.75 x 17 x 3
4.00 / 5.00 17.7 442 12.7 317
9.4
235
SNS-25-40-11-AB
25
170
11
4.0
8.25
8.0 - 9.0
0.75 x 17 x 3
4.00 / 5.00 4.8
120
2.6
65
1.0
25
SNS-25-40-7-AB
25
245
7
4.0
8.25
8.0 - 9.0
0.75 x 17 x 3
4.00 / 5.00 10.8 270
7.7
192
5.4
135
SNS-25-50-11-AB
25
225
11
5.0
11
10 - 12
0.75 x 17 x 3
4.00 / 5.00 9.8
6.3
157
3.7
92
SNS-25-50-7-AB
25
360
7
5.0
11
10 - 12
0.75 x 17 x 3
4.00 / 5.00 18.5 462 13.3 3332 9.5
237
SNS-30-40-7-AB
30
291
7
5.0
8.25
8.0 - 9.0
0.75 x 17 x 3
4.00 / 5.00 6.7
167
65
SNS-30-50-11-AB
30
265
11
5.0
11
10 - 12
0.75 x 17 x 3
4.00 / 5.00 4.7
117
2.0
50
--
--
SNS-30-50-7-AB
30
380
7
5.0
11
10 - 12
0.75 x 17 x 3
4.00 / 5.00 10.7 267
6.7
167
3.9
97
SNS-30-60-7-AB
30
520
7
6.0
12.5
11 - 13
1 x 36 x 4
4.75 / 5.75 19.0 475 13.2 330
9.0
225
SNS-35-50-7-AB
35
440
7
5.0
11
10 - 12
0.75 x 17 x 3
SNS-35-60-7-AB
35
540
7
6.0
12.5
11 - 13
SNS-39-60-7-AB
39
605
7
6.0
12.5
11 - 13
4.00 / 5.00 5.9
240
245
6.7
4.4
110
2.6
147
2.5
62
--
--
1 x 36 x 4
4.75 / 5.75 12.4 310
7.6
190
4.2
105
1 x 36 x 4
4.75 / 5.75 7.2
3.0
75
--
--
180
Pole Shaft
The pole shall be a one section design fabricated from standard 11 gauge (0.1196”) or 7 gauge (0.1793”) steel. Each section shall
be fabricated from high strength low alloy steel conforming to ASTM A500 Grade B, with minimum yield strength of 46,000 psi. Each
pole will have a full-length longitudinal weld and will be square in cross-section.
Base Plate
The base plate is fabricated from a structural quality hot rolled carbon steel plate that meets or exceeds ASTM A-36 with a minimum
yield of strength of 36,000 psi. The base plate telescopes the pole shaft and is circumferential welded top and bottom. The base plate
has slotted bolt holes.
Hand Hole
A reinforced hand hole, having a nominal 3” x 5” opening, will be installed 18” above the base plate on all poles. A hand hole cover
and attaching hardware is included with each hand hole assembly. A ground lug will be welded either on the hand hole frame or on
the inside of the pole opposite the hand hole depending on the design.
Anchor Bolts
Anchor bolts are fabricated from a commercial quality hot rolled carbon steel bar that meets or exceeds minimum yield strength of
55,000 psi. Anchor bolts are sized according to each pole design and are furnished with 2 galvanized heavy hex nuts and 2 galvanized flat washers. Anchor bolts shall be galvanized a minimum of 4” on the threaded end in accordance with ASTM A-153. Anchor
bolts will ship with the poles unless otherwise specified.
Pole Top
Each pole will be side-drilled with a removable pole cap or have a 2-3/8” O.D. x 4” tenon top (other sizes available).
Welding
All welds shall be of the highest quality and performed by American Welding Society certified welders conforming to the latest version
of the American Welding Society specification AWS D1.1.
Finish
All poles, mounting brackets and platforms are furnished with a coating of either red oxide/zinc primer, factory painted, powder coated
or hot-dip galvanized to ASTM A-123. Miscellaneous hardware will be galvanized to ASTM A-153. Exterior finish coatings are available by request.
Note
Anchor bolt patterns are subject to change. Please consult factory prior to construction.
Bolt Circle
Anchor Bolt
Projection
Width
Slotted
Holes
Base Plate
Base Detail
Poles should be monitored frequently
for signs of harmonic vibration, which
may cause structural fatigue. Consult
factory for a damping device that can
help minimize the effects of vibration.
Phone: (866) 474-7200 • Fax: (817) 924-7049
American Lite Pole reserves the right to change any portion of this publication without notice in order
to promote product improvement and allow for material availability.
14
Area Lighting Poles - Square Tapered
Catalog
Number
Pole
Weight
Height
Guage
(lbs)
(ft)
Shaft
Size (in)
Base
Bolt
Plate
Circle
Width
Dia. (in)
(in)
STS-20-525-11-AB
20
155
11
5.25 x 3.05 10.75
STS-25-600-11-AB
25
205
11
6.00 x 3.25
STS-30-641-11-AB
30
260
11
STS-30-641-7-AB
30
375
7
STS-35-681-11-AB
35
305
11
STS-35-713-7-AB
35
475
7
STS-39-718-11-AB
39
345
STS-39-713-7-AB
39
500
Anchor Bolts
(in)
Dia x Len x Hook
Max Loading Capacities
80 (mph) 90 (mph) 100 (mph)
Projection EPA Wt. EPA Wt. EPA Wt.
min / max (ft2) (lbs) (ft2) (lbs) (ft2) (lbs)
10.75
1 x 36 x 4
4.5 / 5.5
18.0 450 13.8 345 10.7 267
12
1 x 36 x 4
4.5 / 5.5
16.8 420 12.6 315
9.5
237
6.41 x 3.11 11.88
12.5
1 x 36 x 4
4.5 / 5.5
13.6 340
7.0
175
6.41 x 3.11 11.88
12.5
1 x 36 x 4
4.5 / 5.5
23.6 590 17.9 447 13.7 342
6.81 x 2.96 12.25
13
1 x 36 x 4
4.5 / 5.5
10.7 267
7.13 x 3.28 12.63
13.5
1 x 36 x 4
4.5 / 5.5
23.4 585 17.4 435 13.0 325
11
7.18 x 2.92 12.63
13.5
1 x 36 x 4
4.5 / 5.5
8.6
7
7.13 x 2.87 12.63
13.5
1 x 36 x 4
4.5 / 5.5
19.3 482 14.2 355 10.4 260
11.5
215
9.8
7.3
5.4
245
182
135
4.8
3.0
120
75
Pole Shaft
The pole shall be a one section design fabricated from standard 11 gauge (0.1196”) or 7 gauge (0.1793”) steel. Each section shall be
fabricated from high strength low alloy steel with minimum yield strength of 50,000 psi. Each pole will have a full-length longitudinal
weld and will be square in cross-section with a uniform taper of 0.11 inches per foot of length.
Base Plate
The base plate is fabricated from a structural quality hot rolled carbon steel plate that meets or exceeds ASTM A-36 with a minimum
yield of strength of 36,000 psi. The base plate telescopes the pole shaft and is circumferential welded top and bottom. The base plate
has round bolt holes.
Hand Hole
A reinforced hand hole, having a nominal 3” x 5” opening, will be installed 18” above the base plate on all poles. A hand hole cover
and attaching hardware is included with each hand hole assembly. A ground lug will be welded either on the hand hole frame or on
the inside of the pole opposite the hand hole depending on the design.
Anchor Bolts
Anchor bolts are fabricated from a commercial quality hot rolled carbon steel bar that meets or exceeds minimum yield strength of
55,000 psi. Anchor bolts are sized according to each pole design and are furnished with 2 galvanized heavy hex nuts and 2 galvanized flat washers. Anchor bolts shall be galvanized a minimum of 4” on the threaded end in accordance with ASTM A-153. Anchor
bolts will ship with the poles unless otherwise specified.
Pole Top
Each pole will be side-drilled with a removable pole cap or have a 2-3/8” O.D. x 4” tenon top (other sizes available).
Welding
All welds shall be of the highest quality and performed by American Welding Society certified welders conforming to the latest version
of the American Welding Society specification AWS D1.1.
Finish
All poles, mounting brackets and platforms are furnished with a coating of either red oxide/zinc primer, factory painted, powder coated
or hot-dip galvanized to ASTM A-123. Miscellaneous hardware will be galvanized to ASTM A-153. Exterior finish coatings are available by request.
Note
Anchor bolt patterns are subject to change. Please consult factory prior to construction.
Bolt Circle
Anchor Bolt
Projection
Width
Bolt Holes
Base Plate
15
Base Detail
Phone: (866) 474-7200 • Fax: (817) 924-7049
American Lite Pole reserves the right to change any portion of this publication without notice in order
to promote product improvement and allow for material availability.
Area Lighting Poles - Square Hinged
Catalog
Number
Pole
Weight
Height
Guage
(lbs)
(ft)
Shaft
Size (in)
Base
Bolt
Plate
Circle
Width
Dia. (in)
(in)
Anchor Bolts
(in)
Max Loading Capacities
80 (mph) 90 (mph) 100 (mph)
Dia x Len x Hook
Projection EPA Wt. EPA Wt. EPA Wt.
min / max (ft2) (lbs) (ft2) (lbs) (ft2) (lbs)
SNSHG-20-40-7-AB
20
300
7
4.0
9.75
8.5 - 10.0
0.75 x 17 x 3
4.25 / 5.25 11.6 217 8.5 217 6.2 217
SNSHG-25-40-7-AB
25
370
7
4.0
9.75
8.5 - 10.0
0.75 x 17 x 3
4.25 / 5.25
7.1 160 4.8 160 3.1 160
SNSHG-30-40-7-AB
30
435
7
4.0
9.75
8.5 - 10.0
0.75 x 17 x 3
4.25 / 5.25
4.0 120 2.1 120 0.8 120
STSHG-25-641-11-AB
25
355
11
6.41 x 3.60 11.88
12.5
1 x 36 x 4
4.75 / 5.75 18.0 254 13.0 254 9.3 254
STSHG-30-641-11-AB
30
440
11
6.41 x 3.10 11.88
12.5
1 x 36 x 4
4.75 / 5.75 12.5 230 8.3 230 5.1 230
STSHG-35-718-11-AB
35
540
11
7.18 x 3.30 12.63
13.5
1 x 36 x 4
4.75 / 5.75
STSHG-35-713-7-AB
35
700
7
7.13 x 3.30 12.63
13.5
1 x 36 x 4
5.00 / 6.00 22.0 155 16.9 155 12.1 155
STSHG-39-718-11-AB
39
555
11
7.18 x 2.90 12.63
13.5
1 x 36 x 4
4.75 / 5.75
STSHG-39-713-7-AB
39
740
7
7.13 x 2.84 12.63
13.5
1 x 36 x 4
5.00 / 6.00 19.5 110 13.5 110
7.1 160 3.2 160
4.3 135
--
--
--
--
--
--
9.2
110
Pole Shaft
The pole shall be a one section design fabricated from standard 11 gauge (0
(0.1196”)
(0.1196
1196”)) or 7 gauge (0.1793”)
(0
(0.1793
1793”)) steel.
steel Each section shall
be fabricated from high strength low alloy steel conforming to ASTM A500 Grade B, with minimum yield strength of 46,000 psi for
non-tapered poles and 50,000 psi for tapered poles. Each pole will have a full-length longitudinal weld and will be square in crosssection. Tapered poles will have a uniform taper of 0.11 inches per foot of length.
Base Plate
The base plate is fabricated from a structural quality hot rolled carbon steel plate that meets or exceeds ASTM A-36 with a minimum
yield of strength of 36,000 psi. The base plate telescopes the pole shaft and is circumferential welded top and bottom. The base plate
has slotted bolt holes.
Hand Hole
A reinforced hand hole, having a nominal 3” x 5” opening, will be installed 18” above the base plate on all poles. A hand hole cover
and attaching hardware is included with each hand hole assembly. A ground lug will be welded either on the hand hole frame or on
the inside of the pole opposite the hand hole depending on the design.
Anchor Bolts
Anchor bolts are fabricated from a commercial quality hot rolled carbon steel bar that meets or exceeds minimum yield strength of
55,000 psi. Anchor bolts are sized according to each pole design and are furnished with 2 galvanized heavy hex nuts and 2 galvanized flat washers. Anchor bolts shall be galvanized a minimum of 4” on the threaded end in accordance with ASTM A-153. Anchor
bolts will ship with the poles unless otherwise specified.
Pole Top
Each pole will be side-drilled with a removable pole cap or have a 2-3/8” O.D. x 4” tenon top (other sizes available).
Welding
All welds shall be of the highest quality and performed by American Welding Society certified welders conforming to the latest version
of the American Welding Society specification AWS D1.1.
Finish
All poles, mounting brackets and platforms are furnished with a coating of either red oxide/zinc primer, factory painted, powder coated
or hot-dip galvanized to ASTM A-123. Miscellaneous hardware will be galvanized to ASTM A-153. Exterior finish coatings are available by request.
Note
Anchor bolt patterns are subject to change. Please contact factory prior to construction.
Top Shaft
Anchor Bolt
Wire
Protection
Shroud
Projection
Hinge Pin
Bottom Shaft
Winch Detail
Base Detail
Hinge Detail
Bolt Circle
Width
Bolt Holes
or Slotted
Holes
Poles should be monitored frequently
for signs of harmonic vibration, which
may cause structural fatigue. Consult
factory for a damping device that can
help minimize the effects of vibration.
Base Plate
Phone: (866) 474-7200 • Fax: (817) 924-7049
American Lite Pole reserves the right to change any portion of this publication without notice in order
to promote product improvement and allow for material availability.
16