1. No category

Patriotic Pop Set
Wall Quilt
47" x 47"
Table Runner
19" x 50½"
Placemat
14" x 18"
Set Designed By: Sue Harvey & Sandy Boobar of Pine Tree Country Quilts
Finished Block Sizes: 9" x 9" for wall quilt and runner and 12" x 12" for placemats
Number of Blocks: 16 for wall quilt, 5 for runner, and 4 for placemats
www.quiltingtreasures.com
1
Patriotic Pop Set
QUILT FABRIC
REQUIREMENTS
Design:
22750 N
22754 Z
22751 N
22755 N
22752 B
22755 R
22753 N
22751 B
WALL QUILT
Yards
22750 N
1
22751 N
⅝
22752 B
½
22753 N
¼
22754 Z
¾
22755 N
1¼
22755 R
⅔
22751 B
(Backing only)
3¼
22755 R: Red Texture
• Cut (7) 2¾" x WOF strips; recut into (64) 2¾" G squares
and (16) 2¾" x 5" H rectangles
Cutting Directions
WOF = Width of fabric from selvedge to selvedge. Label all
pieces with the letters/numbers given in the cutting list.
These letters are used to identify the pieces throughout the
instructions.
22751 B: Flag Print (Backing Only)
• Cut (2) 55" x WOF pieces for backing
Navy Star Blocks
Note: Use a ¼" seam allowance for all stitching.
22750 N: Ribbon/Star Print
• Cut (1) 5" x WOF strip; recut into (8) 5" A squares
• Cut (5) 5" x WOF strips for outer border
1. Draw a diagonal line on the wrong side of each navy
C square.
22751 N: Flag Print
• Cut (3) 2¾" x WOF strips; recut into (32) 2¾" E squares
• Cut (2) 3⅛" x WOF strips; recut into (16) 3⅛" squares,
then cut in half diagonally to make 32 J triangles
2. Place a marked C square right sides together on one end
of a white B rectangle. Stitch on the marked line. Trim
seam allowance to ¼". Press the navy triangle to the
right side. Repeat with a second C square on the
remaining end of the B rectangle to complete (1) B unit.
Repeat to make (16) B units total. Repeat with the
remaining marked C squares and blue D rectangles
to make (16 D) units.
22752 B: Blue Paisley Print
• Cut (4) 2¾" x WOF strips; recut into (32) 2¾" x 5" D
rectangles
22753 N: Zigzag Stripe
• Cut (1) 5" x WOF strip; recut into (8) 5" F squares
22754 Z: White Dot
• Cut (5) 2¾" x WOF strips; recut into (16) 2¾" x 5" B
rectangles and (32) 2¾" I squares
• Cut (2) 3⅛" x WOF strips; recut into (16) 3⅛" squares,
then cut in half diagonally to make 32 K triangles
Make 16
22755 N: Navy Texture
• Cut (5) 2¾" x WOF strips; recut into (64) 2¾" C squares
• Cut (4) 1½" x WOF strips; recut into (2) 1½" x 36½"
strips and (2) 1½" x 38½" strips for inner border
• Cut (5) 2¼" x WOF strips for binding
www.quiltingtreasures.com
Make 16
3. Sew a B unit to opposite sides of each ribbon/star A
square to make (8) center rows. Press seams toward the
A squares.
4. Stitch a flag E square to each end of the D units to make
(16) top/bottom rows. Press seams toward the E squares.
2
Patriotic Pop Set
5. Sew a center row between (2) top/bottom rows to
complete (1) 9½" x 9½" navy star block. Press seams
toward the center row. Repeat to make (8) blocks total.
5. Sew an H unit to opposite sides of each F unit to make
(8) center rows. Press seams toward the H units.
6. Stitch a JK unit to each end of the D units to make (16)
top/bottom rows. Press seams toward the D units.
7. Sew a center row between (2) top/bottom rows to
complete (1) 9½" x 9½" red star block. Press seams
toward the top/bottom rows. Repeat to make (8) blocks
total.
Make 8
Red Star Blocks
1. Draw a diagonal line on the wrong side of each red G
square and white I square.
Make 8
2. Use marked G squares and blue D rectangles to make
(16) D units referring to step 2 for navy star blocks.
Repeat with the marked I squares and red H rectangles
to make (16) H units.
Make 16
Quilt Assembly:
Note: Refer to the exploded quilt diagram on page 4
throughout the following steps.
1. Join (2) red star blocks and (2) navy star blocks to make
a row. Press seams toward the navy Star blocks. Repeat
to make (4) rows total.
Make 16
3. Place a marked G square right sides together on
opposite corners of a stripe F square. Stitch on the
marked lines. Trim seam allowances to ¼". Press the
red corners to the right side. Repeat on the remaining
corners of the F square to complete (1) F unit. Repeat to
make (8) F units total.
2. Join the rows to complete the 36½" x 36½" quilt center,
turning every other row end for end. Press seams in one
direction.
3. Sew the 1½" x 36½" navy texture strips to opposite
sides and the 1½" x 38½" strips to the top and bottom.
Press seams toward the strips.
4. Sew the 5" ribbon/star border strips short ends together
to make a long strip. Press seams to one side. Cut into
(2) 38½" strips and (2) 47½" strips. Sew the 38½" strips
to opposite sides and the 47½" strips to the top and
bottom to complete the quilt top. Press seams toward the
strips.
Make 8
4. Stitch a flag J triangle to a white K triangle on the long
diagonal edges to make a JK unit. Press seam toward the
J triangle. Repeat to make (32) JK units total.
5. Remove the selvedge edges from the backing pieces.
Join the pieces on the long edges with a ½" seam
allowance. Press seam open. Trim the side edges to
make a 55" x 55" backing piece.
Make 32
www.quiltingtreasures.com
3
Patriotic Pop Set
6. Layer, quilt, and bind using your favorite methods and
the navy texture binding strips to complete the quilt.
Exploded Quilt Diagram
www.quiltingtreasures.com
4
Patriotic Pop Set
TABLE RUNNER
FABRIC REQUIREMENTS
Design:
22750 N
22754 Z
22751 N
22755 N
22752 B
22755 R
22753 N
22751 B
TABLE RUNNER
Yards
22750 N
⅝
22751 N
⅜
22752 B
¼
22753 N
¼
22754 Z
½
22755 N
⅞
22755 R
⅜
22751 B
(Backing only)
1⅔
22751 B: Flag Print (Backing Only)
• Cut (2) 27" x WOF pieces for backing
Cutting Directions
Navy and Red Star Blocks
Note: Use a ¼" seam allowance for all stitching.
WOF = Width of fabric from selvedge to selvedge. Label all
pieces with the letters given in the cutting list. These letters
are used to identify the pieces throughout the instructions.
1. Refer to steps 1 and 2 of the navy star blocks section
(page 2) for the Wall Quilt to make (10) B units and (6)
D units. Set (4) B units aside for Runner assembly.
22750 N: Ribbon/Star Print
• Cut (1) 5" x WOF strip; recut into (3) 5" A squares
• Cut (4) 2½" x WOF strips for outer border
22751 N: Flag Print
• Cut (2) 2¾" x WOF strips; recut into (20) 2¾" E squares
• Cut (1) 3⅛" x WOF strip; recut into (10) 3⅛" squares,
then cut in half diagonally to make 20 J triangles
Make 10
Make 6
2. Refer to steps 3, 4, and 5 (page 2) to make (3) 9½" x
9½" navy star blocks.
22752 B: Blue Paisley Print
• Cut (2) 2¾" x WOF strips; recut into (10) 2¾" x 5"
D rectangles
22753 N: Zigzag Stripe
• Cut (1) 5" x WOF strip; recut into (2) 5" F squares
22754 Z: White Dot
• Cut (3) 2¾" x WOF strips; recut into (10) 2¾" x 5"
B rectangles and (20) 2¾" I squares
• Cut (1) 3⅛" x WOF strip; recut into (10) 3⅛" squares,
then cut in half diagonally to make 20 K triangles
Make 3
3. Refer to steps 1, 2, 3, and 4 of the red star blocks
section (page 3) for the Wall Quilt to make (4) D units,
(10) H units, (2) F units, and (20) JK units. Set (6) H
units and (12) JK units aside for Runner assembly.
22755 N: Navy Texture
• Cut (3) 2¾" x WOF strips; recut into (32) 2¾" C squares
• Cut (3) 1¼" x WOF strips for inner border
• Cut (4) 2¼" x WOF strips for binding
22755 R: Red Texture
• Cut (3) 2¾" x WOF strips; recut into (16) 2¾" G squares
and (10) 2¾" x 5" H rectangles
www.quiltingtreasures.com
5
Make 4
Make 10
Make 2
Make 20
Patriotic Pop Set
4. Refer to steps 5, 6, and 7 (page 3) to make (2) 9½" x
9½" red star blocks.
3. Join the navy star and red star sections to complete the
14" x 45½" runner center. Press seams to one side.
4. Sew the 1¼" navy texture strips short ends together to
make a long strip. Press seams to one side. Cut into (2)
45½" strips and (2) 15½" strips. Sew the 45½" strips to
the long sides and the 15½" strips to the short ends of
the runner center. Press seams toward the strips.
5. Sew the 2½" ribbon/star print strips short ends together
to make a long strip. Press seams to one side. Cut into
(2) 47" strips and (2) 19½" strips. Sew the 47" strips to
the long sides and the 19½" strips to the short ends to
complete the runner top. Press seams toward the strips.
Make 2
Runner Assembly
Note: Refer to the exploded runner diagram (below, right)
throughout the following steps.
6. Remove the selvedge edges from the backing pieces.
Join the pieces on the 27" edges with a ½" seam allowance. Press seam open. Trim the ends to make a 27" x
59" backing piece.
1. Sew a JK unit to each end of the remaining H units to
make (6) pieced strips. Press seams toward the JK units.
Sew a pieced strip to opposite sides of each navy Star
block to make (3) 9½" x 14" navy star sections. Press
seams toward the navy star blocks.
7. Layer, quilt, and bind using your favorite methods and
the navy texture binding strips to complete the runner.
Make 3
2. Stitch a flag E square to each end of the remaining B
units to make (4) pieced strips. Press seams toward the
B units. Sew a pieced strip to opposite sides of each red
star block to make (2) 9½" x 14" red star sections. Press
seams toward the pieced strips.
Exploded Runner Diagram
Make 2
www.quiltingtreasures.com
6
Patriotic Pop Set
PLACEMATS
FABRIC REQUIREMENTS
Design:
22750 N
22754 Z
22751 N
22755 N
22752 B
22755 R
22751 B
PLACEMATS
22750 N
⅓
22751 N
½
22752 B
⅜
22754 Z
⅝
22755 N
1
22755 R
½
22751 B
(Backing only)
1½
Navy Star Blocks
Note: Use a ¼" seam allowance for all stitching.
Cutting Directions
WOF = Width of fabric from selvedge to selvedge. Label all
pieces with the letters given in the cutting list. These letters
are used to identify the pieces throughout the instructions.
1. Refer to steps 1 and 2 (page 2) of the Navy Star Blocks
section for the Wall Quilt to make (8) B units and (8) D
units. Use red H rectangles and white I squares to make
(8) H units. Set H units aside for Placemat assembly.
22750 N: Ribbon/Star Print
•Cut (1) 6½" x WOF strip; recut into (4) 6½" A squares
22751 N: Flag Print
• Cut (2) 3½" x WOF strips; recut into (16) 3½" E squares
• Cut (1) 3⅞" x WOF strip; recut into (8) 3⅞" squares,
then cut in half diagonally to make 16 J triangles
Make 8
Make 8
Make 8
2. Refer to steps 3, 4, and 5 (page 2) to make (4) 12½" x
12½" navy star blocks.
22752 B: Blue Paisley Print
• Cut (2) 3½" x WOF strips; recut into (8) 3½" x 6½"
D rectangles
22754 Z: White Dot
• Cut (3) 3½" x WOF strips; recut into (8) 3½" x 6½" B
rectangles and (16) 3½" I squares
• Cut (1) 3⅞" x WOF strip; recut into (8) 3⅞" squares,
then cut in half diagonally to make (16) K triangles
22755 N: Navy Texture
• Cut (3) 3½" x WOF strips; recut into (32) 3½" C squares
• Cut (8) 2¼" x WOF strips for binding
Make 4
22755 R: Red Texture
• Cut (2) 3½" x WOF strips; recut into (8) 3½" x 6½"
H rectangles
• Cut (4) 1½" x WOF strips; recut into (8) 1½" x 18½"
border strips
22751 B: Flag Print (Backing Only)
• Cut (2) 24" x WOF strips; recut into (4) 20" x 24"
backing pieces
www.quiltingtreasures.com
Yards
7
Patriotic Pop Set
Placemat Assembly
Note: Refer to the exploded placemat diagram (below)
throughout the following steps.
1. Sew a J triangle to a K triangle on the long diagonal
edges to make a JK unit. Press seam toward the J
triangle. Repeat to make (16) JK units total.
Make 16
2. Sew a JK unit to each end of the H units to make (8)
pieced strips. Press seams toward the JK units. Sew a
pieced strip to opposite sides of each navy star block to
make (4) 12½" x 18½" placemat centers. Press seams
toward the navy star blocks.
3. Sew a 1½" x 18½" red texture border strip to the long
sides of each placemat center to complete the tops. Press
seams toward the border strips.
4. Layer, quilt, and bind using your favorite methods and
the flag print backing pieces and the navy texture
binding strips to complete the placemats.
Exploded Placemat Diagram
While all possible care has been taken to ensure the accuracy of this
pattern, we are not responsible for printing errors or the way in which
individual work varies.
www.quiltingtreasures.com
8
Not For Resale/Winter 2013