1. No category

AURVTG008 Cut and process flat laminated glass
AURVTG008
Application
Cut and process flat laminated glass
This unit describes the performance outcomes required to measure, mark, cut
and process flat laminated glass for installation into vehicles and equipment.
It applies to those working in an automotive glazing and body repair environment
and involves application of skills and knowledge to prepare measure and cut flat
laminated glass.
Competency Field
Unit Sector
ELEMENT
Licensing, legislative, regulatory or certification requirements may apply to this
unit in some jurisdictions. Users are advised to check with the relevant
regulatory authority.
Vehicle Body
Technical - Glazing
PERFORMANCE CRITERIA
Elements describe the essential
outcomes
Performance criteria describe the performance needed to demonstrate achievement of
the element. Where bold italicised text is used, further information is detailed in the
range of conditions section
1
Prepare for work
2
Fabricate templates and
patterns
1.1
1.2
1.3
1.4
2.1
2.2
3
Measure, mark and cut glass
3.1
3.2
4
Process glass edges
4.1
4.2
5
Complete work processes
5.1
5.2
5.3
5.4
5.5
Work order and work instruction is used to determine job requirements
Laminated glass is selected according to work order and job specification
Glass cutting equipment is identified and checked for safe operation
Cutting plan is prepared to minimise off cuts
Suitable materials are selected to fabricate templates and patterns
Template and pattern are marked out and fabricated according to work
order and work health and safety (WHS) requirements
Glass is measured, marked and cut out according to measurements,
template and pattern
Glass cutting is completed according to workplace procedures and without
causing personal injury and damage to the glass being cut
Arris and bevel glass edges is completed within established workplace
procedures
All edge processing activities are carried out according to WHS safety
requirements
Report work outcome to supervisor
Off cut glass sections are collected and stored or discarded depending on
size
Scrap glass sections are removed following workplace procedure
Tools, equipment and work area are cleaned, maintained and faulty
equipment is reported according to workplace procedures
Workplace documentation is completed according to workplace procedures
FOUNDATION SKILLS
This section describes those language, literacy, numeracy and employment skills that are essential to performance and are not
explicit in the performance criteria.
Skills
Reading skills to
Writing skills to
Oral Communication skills to
Numeracy skills to
Auto Skills Australia
Description
 interpret work order and work instruction
 interpret glass cutting plan
 identify work instructions.
 legibly complete cutting plan
 legibly complete workplace documents.
 report work outcomes and equipment faults to supervisor
 communicate with fellow workers and customers.
 accurately mark glass sections
 correctly measures templates, patterns and laminated glass components to
specifications
 calculate glass requirements.
Page 1 of 3
AURVTG008 Cut and process flat laminated glass
AURVTG008
Planning and Organising skills to
Problem Solving skills to
Technology skills to
RANGE OF CONDITIONS
Cut and process flat laminated glass
 use personal protection equipment (PPE) requirements to cut flat laminated
glass
 follow work order and work instructions
 prepare flat glass for customer use
 prepare and layout of work area and cutting equipment.
 identify glass surface defects.
 use workplace glass cutting equipment.
This section specifies work environments and conditions that may affect performance. Essential operating conditions that may be
present (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional
contexts) are included. Bold italicised wording, if used in the performance criteria, is detailed below.
Work health and safety (WHS)
must include
Unit Mapping Information
Links


glass handling and scrap glass disposal
use of PPE required to cut flat laminated glass.
Implementation Guide
http://www.asacompanionvolumes.com.au/aur-implementation-guide
Assessment Requirements
Assessment requirements for AURVTG008 Cut and process flat laminated glass
Performance Evidence
Before competency can be determined, individuals must demonstrate they can
perform the following according to the standard defined in this unit’s elements,
performance criteria and foundation skills:

Knowledge Evidence
mark, cut and process three different flat laminated glass section, including;
o arris and bevel cut glass edges.
Individuals must be able to demonstrate knowledge of:

Assessment Conditions
types and use of personal protection equipment (PPE) required to cut
laminated glass
 workplace procedures to cut laminated glass
 glass handling and storage processes
 templates and patterns
 glass cutting methods and techniques
 use of glass cutting and arising equipment
 template and pattern fabrication
 glass cutting and processing procedures
 workplace glass cutting quality standards.
Assessors must satisfy SNR/AQTF assessor requirements.
Competency is to be assessed in the workplace or a simulated environment that
accurately reflects performance in a real workplace setting.
Where assessment of competency includes third party evidence, individuals
must provide evidence that links them to the laminated glass that they prepared
and cut, e.g. work orders.
Assessors must verify performance evidence through questioning on skills and
knowledge to ensure correct interpretation and application.
The following resources must be made available:
Auto Skills Australia
Page 2 of 3
AURVTG008 Cut and process flat laminated glass
Assessment requirements for AURVTG008 Cut and process flat laminated glass







Links
automotive glazing workplace location or simulated workplace
PPE required to cut laminated glass
glass handling and storage procedures
work orders and work instructions
job specifications
materials required to produce templates and patterns
flat laminated glass sections
 tools and equipment required to cut and process flat laminated glass.
Implementation Guide
http://www.asacompanionvolumes.com.au/aur-implementation-guide
Assessment Strategies Guide
http://www.asacompanionvolumes.com.au/aur-assessment-strategies-guide
Auto Skills Australia
Page 3 of 3