1. No category

C 015E-R
RF
PROFESSIONAL MICROPHONE SYSTEMS
The C015
5E-RF combin
nes the slim lines and func
ctionality of the
t
S140 micrrophone
stand, with the sonic quality and robust
r
housin
ng of the C011E-RF microp
phone.
SPECIFIC
CATIONS
C015E-RF
Type:
ndenser (Blac
ck Electret)
Con
ern:
Polar Pate
Om
mni-directiona
al
Frequenc
cy
Response
e:
50Hz - 20KHz
Sensivity::
- 42db ± 3db @ 1 KHz (0db = 1VPa)
Impedanc
ce:
200
0 Ohms
S/N Ratio
o:
58d
db (A)
Switching
g:
Pro
ogrammable for
f
PTT, PTM & Latching
Power
Requirem
ments:
V Phantom Power
48V
Terminatiion:
5Pin XLR with remote
r
switch
h ability
Optional 3Pin XLR
X
Variant
PI
IN 1 = Ground
d
PIN
N 2 = Controll Input (activ
vated in progrram 4
optio
on 2)
PIN
N 3 = PHASE –
PIN
N 4 = Switch Out (Logic lo
ow when swittch
press
sed)
PIN
N 5 = PHASE +
Finish:
Sattin black
'RF Friendly' technolog
gy offering
dio
immunity from GSM rad
frequency interference
e
Dimensio
ons:
Len
ngth
Width
h
Height
120
0mm
(4..8")
mm
100m
(3.94")
30mm
(1.18")
Witth Microphon
ne, Height: 45
5mm (1.77")
Weight:
Programm
ming options
Program mode
m
(P
Press numberr of times
fo
or selection required)
r
1
2
3
Switch Ty
ype
Switch Action
Activation Tone
4
Control Mute
M
5
6
Switchable
S
10
0dB Pad
Bass roll Off
Descriptiion
604
4g (21.3oz)
Option
n1
(Press Once)
O
Option
2
(Prress Twice)
Momenttary
PTT (Norma
ally Off)
Off
n—Microphone muted at
On
base. LED indiicates live
microphone
0dB
100Hz
L
Latching
PTM (
(Normally On)
On
Off---Mic
crophone mu
uted
externally. LED indicates
s Logic
low
-10dB
400Hz
Switch Progrramming Insttructions
1)
Apply
y power with switch press
sed.
2)
Unit gives regular
r flash for 2 seconds
s
on LE
ED to show se
et up mode en
ntered.
3)
Press
s switch the number
n
of tim
mes of the pro
ogramming mode
m
you wis
sh to check orr change. The
e
interrval between key presses must
m
be less than 1 secon
nd.
4)
Afterr the mode ha
as been selec
cted the LED will
w flash the number of times of the op
ption currenttly set.
5)
Press
s the switch the
t
number of
o times of the
e option requ
uired. The intterval betwee
en key presse
es must
be le
ess than 1 sec
cond.
6)
The LED
L
will flash
h the number of times of th
he option alre
eady set.
7)
The unit
u
then retu
urns to stage 2, ready for setting more options.
8)
The unit
u
will retur
rn to normal operation aftter 5 seconds
s if the key is not pressed.