EMBARKED TETRA CAB RADIO FROM AEG Belgium ‐ AEG TCR100 The AEG TCR 100 is an universal telecommunica on on‐board equipment, based on TETRA technology, desig‐ ned for voice and data communica on to be installed in the driver cabins of metros, trams and trains. It enables high quality and reliable voice communica ons between drivers and control centers and controllers in the field. It enables also the recep on and transmi on of various data such as alarms from/to management servers and external systems. The ICR 100 is integrated in one box IP20 where all the electronics is placed. The radio module is mounted inside the box. The ICR 100 itself is mounted in a 19 inch rack as seen on the pictures. This rack is a standard 3U rack, with a width of 183 mm (36 TE). The ICR100 box is mounted in the rack with a quick release mechanism and a heavy duty floa ng connector for railways applica ‐ ons. This allows to exchange the interface within less than 5 minutes. Other kinds of supports all including this quick release mechanism are also available. The AEG Tetra Cab Radio TCR 100 design is modular and flexible‐minded. All the func ons can be customized according to specific needs. It integrates a state‐of‐the art hardware and so ware pla orm with Ethernet in‐ terfaces and Linux embedded opera ng system. The AEG TCR 100 standard configura on includes: TETRA Mobile Radio MR X (X= Sepura; Cassidian; Motorola etc) An interface card ICR100 with interfaces to: A handset (micro telephone) Loudspeaker(s) PA – UIC 568 Internet interface to on board network Processor card Driver Machine Interface – MMI (op onal) An antenna system Interconnec on cables Installa on accessories Tél. : +32 (0) 2 529 62 11 AEG Belgium S.A.‐N.V. Quai de Biestebroeckkaai 300 1070 Brussels [email protected] www.aegtranzcom.com EMBARKED TETRA CAB RADIO FROM AEG Belgium — AEG TCR100 The Radio interface unit has the following interfaces: 4 digital inputs with optocoupler 4 poten al free digital outputs 1 maintenance Ethernet connector connected on the front 1 Ethernet port to be connected to the vehicle Ethernet bus 1 interface for encoder plug with vehicle address and specific data. 1 microphone input 1 speaker output 1 interface for handset; 1 public address output 4 leds on the front for status and diagnos cs 1 power input with igni on with the ability to delayed switch off All the signals are isolated with 1500 Volts AC and protected against transients, inversion and overcurrent and are compliant with the EN50155 norm over the full range of the power supply voltage. The TETRA Cab Radio TCR 100 Implements following func onal‐ i es: Audio management: ambiance microphone in idle mode for ambiance listening calls; rou ng of income call to cab‐ in loudspeaker. Signalling for incoming duplex calls; use of handset, gooseneck microphone, footswitch; volume se ngs etc; full duplex call; emergency calls Messaging: statuses and text messages; Group management; TETRACabRadioTCR100 Dimensions Weight Operating temperature Power supply Power consumption Certification Applicable norms and certificates Protection 325 (depth) x 183 (width) x 133 (height) mm (including 19 inch rack) 2,5 kg -25°C to +70°C (EN 50155 T3) 24 Vdc, 72 Vdc or 110 Vdc 20 W in idle, up to 50 W max (depending on radio power and network conditions) EN50155, EN 45545-2, NF 16-101 and NF 16-102 EN55011 group 1 class A, CISPR 25 E dir 2004/104/CE (24 V only), EN61000 -4-2, EN61000-4-3, EN 61000-4-4, EN 61000-4-5, EN61000-4-6, EN 60068-21, EN60068-2-2, EN60068-2-14, EN60068-2-30, EN60068-2-27, EN61373, EN60068-2-14, EN ETS 300019-2-5 class 5M3EN61373, EN60068-2-64 IP20 Tél. : +32 (0) 2 529 62 11 AEG Belgium S.A.‐N.V. Quai de Biestebroeckkaai 300 1070 Brussels [email protected] www.aegtranzcom.com EMBARKED TETRA CAB RADIO FROM AEG Belgium — AEG TCR100 Main advantages of the AEG TETRA Cab Radio solu on: It can integrate all types of Tetra Radio Modules (Transceivers). Possibility to integrate other mo‐ bile radio technologies like DMR or Nexedge. Automa c detec on of mobile radio type. It is compliant with the Railways norms EN 50155 and also with the norms applicable to road ve‐ hicles such as public transport busses. It has a modular and flexible design allowing different configura ons and func onal customiza on according to specific needs. It integrates a state‐of‐the art hardware and so ware pla orm with a high performance on‐ board computer, Ethernet interfaces and Linux embedded opera ng system. It integrates a DSP audio interface for audio management (level adjustment, speakers, micropho‐ nes, receivers and their hook, p or full duplex calls, ...) easy to adapt to existant audio devices. It integrates interfaces to other on‐board equipment: I/O interfaces; RS485; front panel Ethernet for maintenance; rear pannel Ethernet to the vehicle; etc A code plug located in the front plate containing all the radio and vehicle specific parameters stored in non vola le memory. MMI applica on runs on the cab radio as web applica on – fully customizable according to spe‐ cific requirements. This allows also integra on with exis ng on board computers. It is available in 24 Volts DC, 72 Volts DC and 110 Volts DC Maintenance tools allow remote configura on and diagnos cs: Maintenance PC with embedded Web server and monitoring server Tests tools level 1 & level 2 are available Very easy installa on and service with very low MTTR. AEG TranzCom core business is public transport : know-how of transport market, vehicles environment, standards and certification process Own capacity of software and hardware development – design, development, manufacturing, testing, supply and after-sales services. Worldwide market leader in the supply of TETRA Cab Radios (more than 7000 units supplied) Tél. : +32 (0) 2 529 62 11 AEG Belgium S.A.‐N.V. Quai de Biestebroeckkaai 300 1070 Brussels [email protected] www.aegtranzcom.com EMBARKED TETRA CAB RADIO FROM AEG Belgium — AEG TCR200 The AEG TCR 200 is an universal telecommunica on on‐board equipment, based on TETRA technology, desig‐ ned for voice and data communica on to be installed in busses. The TCR 200 The AEG Tetra Cab Radio design is modular and flexible‐minded. All the func ons can be custom‐ ized according to specific needs. It integrates a state‐of‐the art hardware and so ware pla orm with Ethernet interfaces and Linux embedded opera ng system. The TCR 200 consists of two units integrated in two separated IP 20 box as follows: 1 B‐MR TETRA Mobile Radio MR X (X= Sepura; Cassidian; Motorola etc) An audio card B‐ICR100 with interfaces to: A handset (micro telephone) Loudspeaker(s) PA Internet interface to on board network Processor card Driver Machine Interface – MMI (op onal) An antenna system Interconnec on cables The Tetra Cab Radio integrates audio management interfaces (level adjustment, speakers, microphones, receivers and their hook, p or full duplex calls, ...), and can be connected depending on the type of vehicle to: new or exis ng audio peripherals; The control unito of the radio AEG Tetra MMI or an exis ng MMI Other electronic equipment on‐board through ethernet and RS485 interfaces. Tél. : +32 (0) 2 529 62 11 AEG Belgium S.A.‐N.V. Quai de Biestebroeckkaai 300 1070 Brussels [email protected] www.aegtranzcom.com EMBARKED TETRA CAB RADIO FROM AEG Belgium — AEG TCR200 Following interfaces to on‐board systems are available: 4 digital inputs / 4 outputs 1 RS485 bus 1 maintenance Ethernet bus connected on the front 1 Ethernet bus connected to the vehicle on the rear connector 1 interface for encoder plug with vehicle address and specific data. 2 microphone inputs 2 speaker outputs 4 leds on the front 1 power inputs with igni on and delayed shut down The TETRA Cab Radio TCR 100 Implements following func onali es: Emergency call—send of SDS to the control center Radio faults sent to the maintenance center Messages SDS sent by other systems on‐board Detec on of the driver’s cabin ac ve volume se ngs etc; Group calls ; emergency calls; Messaging: statuses and text messages; Simultaneous voice and SDS management Ethernet Interface to on‐board bus equipment TETRACabRadioTCR200 Dimensions Weight Operating temperature Power supply Power consumption Certification Protection 325 (depth) x 183 (width) x 133 (height) mm (including 19 inch rack) 2,5 kg -25°C to +70°C (EN 50155 T3) 24 Vdc 20 W in idle, up to 50 W max (depending on radio power and network conditions) EN50155, EN 45545-2, NF 16-101 and NF 16-102 IP20 Tél. : +32 (0) 2 529 62 11 AEG Belgium S.A.‐N.V. Quai de Biestebroeckkaai 300 1070 Brussels [email protected] www.aegtranzcom.com EMBARKED TETRA CAB RADIO FROM AEG Belgium — AEG TCR200 Main advantages of the AEG TETRA Cab Radio solu on: It can integrate all types of Tetra Radio Modules (Transceivers). Possibility to integrate other mobile radio like PMR. Automa c detec on of mobile radio type. It is compliant with the Railways norms EN 50155 and also with the norms applicable to road vehicles such as public transport busses. It has a modular and flexible design allowing different configura ons and func onal customiza‐ on according to specific needs. It integrates a state‐of‐the art hardware and so ware pla orm with a high performance on‐ board computer, Ethernet interfaces and Linux embedded opera ng system. It integrates an interface audio DSP for audio management (level adjustment, speakers, micro‐ phones, receivers and their hook, p or full duplex calls, ...) easy to adapt to existant audio devi‐ ces. It integrates interfaces to other on‐board equipment: I/O interfaces; RS485; front panel Ether‐ net for maintenance; hear pannel Ethernet to the vehicle; etc A code plug located in the front plate containing all the radio and vehicle specific parameters stored in non vola le memory. MMI applica on runs on the cab radio as web applica on – fully customizable according to specific requirements. It is available in 24 Volts DC Maintenance tools allow remote configura on and diagnos cs: Maintenance PC with embed‐ ded Web server and monitoring server Tests tools level 1 & level 2 are available Very easy installa on and service with very low MTTR. AEG TranzCom core business is public transport : know-how of transport market, vehicles environment, standards and certification process Own capacity of software and hardware development – design, development, manufacturing, testing, supply and after-sales services. Worldwide market leader in the supply of TETRA Cab Radios (more than 7000 units supplied) Tél. : +32 (0) 2 529 62 11 AEG Belgium S.A.‐N.V. Quai de Biestebroeckkaai 300 1070 Brussels [email protected] www.aegtranzcom.com EMBARKED TETRA CAB RADIO FROM AEG Belgium AEG TCR100/TCR 200 TEST EQUIPMENT The AEG TCR 100 / TCR 200 is an universal telecommunica on on‐board equipment, based on TETRA technology, designed for voice and data communica on to be installed in the driver cabins of Metro, RER, busses and trams. Various tes ng tools will be provided to test the AEG TETRA Cab Radio TCR100/TCR200: The level 1 test tools allow to test: Wiring and devices (HP, Micro, PTT, Satellite) The func oning of devices and the PE in the TETRA system (test OK or KO) The parameter checking and diagnosis of PE in real me Benchmarks level 2 tools that allow to: Perform tests on the TCR cab radio to detect the faulty circuit board Qualify new devices Tél. : +32 (0) 2 529 62 11 AEG Belgium S.A.‐N.V. Quai de Biestebroeckkaai 300 1070 Brussels [email protected] www.aegtranzcom.com The state of the art software and hardware platforms of the AEG TETRA Cab Radios TCR100 and TCR200 allows easily implementation of applications integrated to other on-board systems. AEG development team is happy to support you in designing the optimal integrated application solution to increase operating efficiency AEG TETRA Cab Radio TCR200— Applica ons on‐board Data applica ons Innova ve data applica ons will be decisive in increasing the efficiency in the services provided by the mass public transport companies. Some examples: Vehicle sensors: how much diesel is le in a par cular bus; alarms, cri cal diagnos cs problems etc. update passenger informa on system—problems on the line; Manage fleet flow: if two buses are all together the central control can ask one bus to slow down; Automa c Vehicle Loca on Doors opened/closed METROS/ Commu ng Trains As train is progressing on the track the talk groups change as there are different talk groups for the different sec ons of the track Passenger alarm calls; Tél. : +32 (0) 2 529 62 11 AEG Belgium S.A.‐N.V. Quai de Biestebroeckkaai 300 1070 Brussels [email protected] www.aegtranzcom.com
© Copyright 2024