EQUIPMENT LIFTING w w w. K O I A U T O...

LIFTING
LIFTING
EQUIPMENT
EQUIPMENT
KOI Auto Parts.
Great Brands.
Great Service.
w w w. K O I A U T O PA R T S . c o m
•
1-800-354-0408
LIFTING EQUIPMENT
SERVICE JACKS
HWAHW93652
HWAHW93642
HWAHW93652
3 Ton SUV Service Jack
• Heavy duty frame for rugged applications
• Longer chassis ideal for truck’s & SUV’s
• One piece “T” handle for easy positioning and
less lifting effort
• Foam handle pad protects the vehicle
• U-joint release mechanism for precise load control
HWAHW93642
2 Ton Heavy Duty Service Jack
•
•
•
•
•
•
•
•
One-piece handle
Flanged side plates increase strength
In-line pump provides efficient pumping operation
Full swivel rear casters for easy positioning
Sealed hydraulic pump for durability
Pressure relief valve prevents overloading
Cast iron lift arm for heavy duty loads
U-joint release mechanism for precise load control
HWAHW93660
HWAHW93657
4 Ton Manual Hydraulic Service Jack
•
•
•
•
•
WLMW1617
Handle adjusts to three pumping positions
Extra long chassis reaches under low overhangs
“T” handle permits easier maneuvering
Automatic valve prevents overloading
Low height 5-1/4", High height 26"
HWAHW93660
10 Ton Manual Hydraulic Service Jack
WLMW1617
3 Ton Service Jack
•
•
•
•
• 6,000 lb. capacity
• Max. height 21-1/4"
• Steel lifting saddle with 360° swivel
Chassis and handle reach under long, low overhangs
Large handle knob provides fine load release control
Handle adjusts to three pumping positions
Forged steel hydraulic unit base is sealed for
long life and reliability
• Automatic valve prevents overloading
• Low height 5-7/8", High height 26"
OTC1505B — 5 Ton Service Jack
OTC1510B — 10 Ton Service Jack
HWAHW93662
HWAHW93662
10 Ton Air/Manual Hydraulic
Service Jack
OTC1505B
OTC1510B
• Operates manually or with air.
• Patented “Speed Pak” eliminates
handle pumping, saves lift times
— the air does the work.
• Loads moved into position
hydraulically. Air hose may be
disconnected for other uses.
Specifications:
Capacity:
Lifting Range:
Saddle Diameter:
Overall Reach:
Frame Height:
Handle Length:
Floor Space:
Weight:
OTC1739
Two-Speed, 3 Ton Jack
• Padded jack handle is angled back, allowing you to
easily extended the jack without banging the handle
against the bumper.
• At load in just one stroke.
• Positioning under air dams is easy, thanks to the 48"
long handle and the jack’s 30-1/2" chassis length.
• Specially designed square saddle provides a safe
and secure lifting platform.
• The largest power unit in its class, with a massive,
sealed cylinder that prevents contamination from dirt
and moisture, ensuring a long life.
• Conforms to ANSI PALD Part 10
Specification:
Capacity:
Lifting range:
Saddle square:
Overall reach:
Frame height:
Handle length:
Floor space:
2
OTC1739
3 Tons
4" to 24-1/2"
6-1/2"
27"
7"
48"
30-1/2" x 15-3/4"
• A built-in safety overload prevents using
the jack beyond its rated capacity.
• Convenient foot pedal speeds the lifting
operation. Handle lock and release control
are located on top of the handle. Handle
can be locked into any position from
vertical to horizontal.
• Spring-loaded 40" handle.
OTC1505B
OTC1510B
5 Ton
6" to 22"
5-1/8"
47"
7-3/4"
43"
14-3/4" to 56"
232 lbs.
10 Ton
5-3/4" to 22"
6"
51"
9-3/4"
43-1/4"
18" to 60"
412 lbs.
AIR JACKS
HERAJ2
HERAJ3
HERAJ2, HERAJ3
AJ-2 & AJ-3 Air Jacks
Use wherever jacks are needed including frame
machines, wheel removal, brake and tire work.
• 6-1/2" to 23-3/16" positions with 4500 lbs. capacity
www.koiautoparts.com
LIFTING EQUIPMENT
FLOOR JACKS
WLMW1620
WLMW1630
WLMW1620
1-1/2 Ton Aluminum Floor Jack
• 3,000 lb. capacity
• 3-1/2" to 17-1/2" Lift Range
• Rubber saddle prevents marring,
rotates 360°
• 37 lb. GSW
WLMW1614
WLMW1614
2 Ton Floor Jack
• 4,000 lb. capacity
• Maximum height 15"
• Swivel casters for easy positioning
WLMW1630
1-1/2 Ton Rapid Lift
Aluminum Floor Jack
•
•
•
•
3-5/8" to 17-1/2" Lift range
47-3/4" Cushion grip handle
3 Pumps to maximum height
360° Swivel saddle with
rubber cushion
WLMW1618
2-1/2 Ton High Lift Floor Jack
WLMW1618
• Designed for SUVs and other high
ground clearance vehicles
• 5-3/8" to 21" Lift range
• 5,000 lb. capacity
• Heavy duty construction
WLMW1616
WLMW1612
WLMW1612
2-1/2 Ton Commercial Floor Jack
•
•
•
•
5,000 lb. capacity
Maximum height 19-1/4"
Heavy duty construction
84 lb. GSW
WLMW1616
3 Ton Rapid Lift Floor Jack
• 6,000 lb. capacity
• 4-5/8" to 19-3/4" Lift Range
• Rapid lift feature allows you to quickly raise
jack into position under the vehicle
AXLE JACKS
OTC1788A
22 Ton Capacity Under-Axle Jack
OTC5012A
25 Ton Capacity Under-Axle Hydraulic Jack
and Accessories
• Self-retracting, air-driven ram uses standard
shop air. Release valve automatically applies
air to retract ram.
• Low 8" minimum working height enables jack
to get under any truck in the shop.
• Positioning jack is easy, even under vehicles
with set-back axles, thanks to a 53" handle
that locks into any of three positions, from
vertical to horizontal.
• Maximum lift is 21" when used with the 3"
lifting extension (included).
• Covered by the OTC Lifetime Marathon
Warranty®. Exceeds ANSI PALD standards.
• Weight: 117 lbs.
• Includes No. 220972 Lifting extension. (3" long
and a 1" diameter. Wt., 3 lbs., 4 oz.)
OTC5012A
1-800-354-0408
Specifications:
Lifting range:
with screw retracted:
Lifting range:
with screw extended:
Cylinder stroke:
Extended screw Length:
PSI range:
8" min. height
13-1/8" max. height
12-7/8" min. height
18" max. height
5-1/8"
4-7/8"
100-200
OTC1788A
• Self-retracting, spring return feature.
• Long 50" T-handle lets you easily position
jack under vehicles with long overhangs.
• One pull of the handle activates the selfretracting 22 ton capacity ram without
having to crawl underneath the vehicle.
• Jack has large rubber-tired wheels.
• Lifting range:
Screw Extd. – 8" min./17" max. ht. w/adpt.
Screw Retd. – 8" min./12-1/2" max. ht.
• Cylinder stroke, 4-3/4"; extended screw
length, 5"; PSI range, 90-145.
• Weight: 102 lbs.
HWAHW93733
20 Ton Air Operated Hydraulic Service Jack
Low Height Pick-Up
•
•
•
•
•
Powerful, compact, portable design
Large 8" rubber wheels for easy maneuverability
Low height allows lifting from axles or suspension
Automatic valve prevents overloading
Rapid two-speed air-hydraulic action quickly
advances ram to load
• Chrome plated plunger for extended jack life
• Built-in overload valve
• Low height 9", High height 19-3/4"
HWAHW93733
3
LIFTING EQUIPMENT
JACK STANDS AND LIFTS
OTC1590
10 Ton Capacity Air Lift Jack for Trucks and Trailers
HWAHW93690
10 Ton Air Actuated End Lift
• Three-way heavy duty brass air valve provides fine control
when lifting or lowering a vehicle
• Safety latch design provides six different automatic safety
lock positions to prevent unintentional lowering of load
• Heavy duty wide base for stability and strength
• Two front swivel caster wheel and two 12" diameter
semi-pneumatic rear tires provide easy maneuvering
• Adjustable lifting arm can be extended to desired position
• Three-way heavy duty brass air valve provides fine control
when lifting or lowering a vehicle
Specifications:
Capacity:
10 Ton
Minimum Height: 12-1/2"
Maximum Height: 50-1/2"
Power Raise:
28"
Saddle Spread:
25" to 53"
Minimum PSI for Rated Load: 200
HWAHW93690
Specifications:
Capacity:
10 tons (at 200 PSI air)
Air pressure:
100 to 200 PSI
Lifting range: 13" to 52"
Saddle width: 29" to 41-3/4"
OTC1590
Height:
67-1/2"
Width:
41"
Length:
36"
Weight:
697 lbs.
Distance from lift arm to floor support: 12-1/2"
OTC1784C
Ratchet-Style Jack Stands
HWAHW93503, HWAHW93506
3 & 6 Ton Jack Stands
• Saddle column provides ratchet action
height adjustment
• Dual purpose handle serves as carry
handle and saddle column release
• Multi position ratchet bar provides
strength and durability
• Formed base adds stability and helps
reduce sinkage into pavement
HWAHW93503
HWAHW93506
WLMW41021, WLMW41022, WLMW41023
Jack Stands
• Ratcheting style for easy adjustments
WLMW41021—2 Ton, 10-3/8" to 16-3/8" Range
WLMW41022—3 Ton, 12" to 17-1/4" Range
WLMW41023—6 Ton, 15-1/2" to 23-1/2" Range
BOTTLE JACK
Hydraulic Bottle Jack
• Adjustable top screw and
a Heavy duty base
WLMW1621 — 2 Ton
WLMW1623 — 4 Ton
WLMW1625 — 6 Ton
WLMW1628 — 8 Ton
WLMW1632 — 12 Ton
WLMW1633 — 20 Ton
4
• Just roll it under a load, adjust the lifting saddles, connect
an air line, and actuate. That’s all it takes to lift the end of a
truck or trailer. Lifting range is 13" to 52" with a 14" reach.
• Develops 10 tons of lift at 200 PSI air pressure. An
automatic mechanical safety catch engages in five height
positions; it must be manually released to lower the load.
• Two large swivel casters and pneumatic tires make it easy
to maneuver, even on loose gravel.
• Pair of 12 ton jack stands
• Formed and welded steel base for strength;
self-locking ratchet handle cannot be released
under load. Durable baked enamel finish
resists corrosion.
• Stands conform to ANSI PALD-4 load rating
standard; factory tested before shipment.
• Base: 12-5/8" x 11-3/8"
• Height range: 19-1/2" to 30-3/4"
OTC1784C
PRH66000
Mid Rise Lift
* Trolley supports the pump and maneuvers the lift from one area of the
shop to another
* Scissors lift design to provide greater stability and support
* Twin cylinder design to help raise load constantly from low to high height
* Screw adapters and swivel lifting pads included with lift
* 4" low height for easy drive on and off
* Safety catch release-in case of hose damage or pump malfunctions, lift
will still support vehicle
* Electronic stop switch prevents electrical system from being damaged
* Sliding arms make it easy to conform to vehicle lift positions
Specifications:
Lift Range:
Low 4"
High 45"
Overall Length: 82"
Overall Width: 41"
Table Length: 61"
Hose Length; 10' (Feet)
Cable Length: 13' (Feet)
Weight:
949 lbs.
Swivel Pads:
High: 6-1/4" x 5" x 4-1/2"
Low: 2" x 5" x 4-1/2"
PRH66000
www.koiautoparts.com
LIFTING EQUIPMENT
LIFTS AND STANDS
OTC1585
Power Train Lift with Tilting Plate
• 1,250 lb. Capacity
• For easy removal and installation of
engine/transaxle assemblies on FWD
vehicles. Also handy for pulling rear
ends, leaf springs, and more.
• Your shop air supply is the only thing
you need to get the precise control
offered by this OTC power train lift.
• Width between wooden support blocks
is adjustable from 0-29". Load is
secured with a tough nylon strap.
WLMW41035
Motorcycle Lift
•
•
•
•
•
•
OTC1585
1,500 lb. capacity
Lift range 4-1/2" to 16-1/2"
Two safety bolts ensure stability
Three position locking levers
Non-slip rubber foot pedal
Easy to roll steel swivel casters
WLMW41035
OTC1545
Motorcycle/ATV Lift
• 1,500 lb. capacity
• Large, 17" long skids will lift the largest,
widest cruisers
• Lowest clearance available, 3-1/2" at lowest
level, with a lift range of 3-1/2" to 16-3/4"
• Removable handle makes for easy
movement around load
• Features also include foot pedal release,
locking rear casters, automatic
safety lock, and two ratcheting
tie down straps for safety
• Weight: 74 lbs.
OTC1545
PAICDOLLY
Steel Car Dolly Set
This steel car dolly set lets you slip your car into the tightest
storage spaces. Just slip them under the wheels and slide
your car where it needs to go.
• Swivel wheels that let you
slide your car into the
tightest of storage spots
• Durable steel construction;
1,000 lb. capacity on each dolly
• Quality swivel ball-bearing
casters for easy movement
• Weight: Approximately
25 lbs. each
PAICDOLLY
CLKGE2002
CLKGE2001
CLKGE2001
10 Piece Garage Kit
CLKGE2002
4 Piece Garage Kit
Contents:
• 2 Ton Hydraulic Floor Jack
• 2 Ton Jack Stands (pair)
• Creeper
• Tire iron / filter wrench
• Wheel chocks
• Magnetic parts bowl / oil basin
Jack Specifications:
• Castors, and Carry Handle
• Min. Ht.: 5.3"; Max. Ht.: 13"
• Swivel Saddle (white for visibility in low light)
• Ht. Adjustable: 10-3/8" to 16-3/8"
Creeper Specifications:
• Oil resistant back and head rest
• 2" swivel castors
Built to ANSI standards
Contents:
• 2 Ton Hydraulic Floor Jack
• 2 Ton Jack Stands (pair)
• Creeper
Jack Specifications:
• Castors, and Carry Handle
• Minimum Height: 5.3"
• Maximum Height: 13"
• Swivel Saddle (white for visibility in low light)
• Height Adjustable: 10-3/8" to 16-3/8"
Creeper Specifications:
• Oil resistant back and head rest
• 2" swivel castors
Built to ANSI standards
1-800-354-0408
5
LIFTING EQUIPMENT
ENGINE STANDS
WLMW41029
2 Ton Folding Engine Crane
WLMW41024
750 lb. Engine Stand
• 3 wheel design with heavy duty swivel casters
for easy maneuvering
• Head assembly rotates 360° and locks in six
positions
• Securely holds most foreign and domestic
engine blocks
• Fully adjustable mounting head assembly
• Rugged, heavy gauge tubular steel construction
• 4000 lb. capacity
• Adjustable boom with chain
and hook
• Legs fold up for easy storage
• PATENTED
WLMW41024
WLMW41029
WLMW41025
1,000 lb. Engine Stand
WLMW41025
HWAHW93808
2 Ton Crane
• 4 wheel design
• Securely holds most foreign and domestic
engine blocks
• Head rotates 360° and locks in six positions
• Fully adjustable mounting head assembly
• Rugged, heavy gauge tubular steel
construction
WLMW41031
1,250 lb. Engine Stand
HWAHW93808
WLMW41031
OTC2015A
1,500 lb. Capacity Underhoist Stand
• Stable four wheel design
• Head rotates 360° and
locks in six positions
• Sturdy metal parts tray
• Lifting height of 54-1/4" to 80-3/4"
• Saddle measures 5-1/4" x 1-1/4"
• 11-7/8" diameter base
OTC2018A
2 Ton Capacity Underhoist Tripod Stand
WLMW41030
3/4 Ton Engine Leveler
•
•
•
•
• Drop forged steel construction
• Heat treated chain and hooks
• Fully adjustable with threaded rod
and 3-position chain mount holes
WLMW41030
Weight: 40 lbs.
Lifting height of 58-7/8" to 91-5/8"
Saddle measures 3-1/4" x 3-1/4"
24" x 24" x 24" tripod base
OTC2015A
OTC2018A
WLMW41032
Engine Lifting Chain
WLMW41033
Engine Lift Plate
PRH40001
1-1/2 Ton Tripod Stand
• 1,000 lb. maximum load
• 24" chain, 28" overall length
• 1,000 lb. Maximum load
• Fits most 2 and 4 barrel intakes
• Lifts engine by intake manifold
• Adjustment pin attached to the stand
secures the support column at six
height positions
• Quick adjust spin handle with thrust
bearing eliminates wear and provides
case of turning under load
• 1" diameter threaded screw has
6-1/2" of travel for fine adjustment
• 3-1/8" x 4-1/2" thick saddle pad
WLMW41032
6
• Legs extend for grater stability
• Four ball bearing casters with
steel wheels
• Four boom positions
WLMW41033
PRH40001
www.koiautoparts.com
LIFTING EQUIPMENT
TRANSMISSION JACKS
OTC1521A
1,000 lb. Capacity Low-Lift Transmission Jack
• Universal mounting head, with adjustable brackets, tilts front to back
and side to side for easy transmission alignment.
• With a height range of 6-1/2" to 29-1/2", it is ideal for today’s groundhugging cars.
• Safety chains hold the load securely, even while moving about the shop.
• Wide, stable wheel base with four swivel casters, and two handle grips
make it easy to position under the vehicle.
• Safety overload prevents jack from being used beyond its rated capacity.
• Pump handle rotates a full 360° for use in any position.
• Flash-chromed ram inhibits rust from entering the hydraulic system.
Cap.
(tons)
1/2
Overall
Length
34-1/2"
Overall
Width
19-3/8"
Max.
Height
29-3/4"
Min.
Height
7-1/2"
OTC1521A
——— Tilt ———
Side Front Back
Weight
30° 60° 17° 128 lbs.
OTC1728
Air-Assisted 1,000 lb. Capacity High-Lift Transmission Jack
OTC1728
• Unique foot pedal design gives you complete control over the airdriven first stage to rapidly raise the mounting head to the
transmission; second stage is hydraulically actuated, permitting
precise operator control during removal and installation.
• Transmission mounting head features four ratcheting brackets that
adjust to fit a wide range of transmissions. Four-wheel base with
locking swivel casters provides stability and portability.
• Safety bypass prevents damage caused by a system overload.
Max.
Cap.
(lbs.)
1000
Overall
Height
(low pos.)
34-1/2"
Leg
Width
41"
Tilt (Maximum)
Side Front Back
10° 50° 20°
Weight
117 lbs.
HWAHW93716
1/2 Ton Floor Style
Transmission Jack
OTC1791
• Universal mounting head provides wide fore and aft tilt range,
making alignment of transmission easier.
• Foot pump and pedal release mechanism gives precise control
when positioning or removing a transmission.
• Adjustable nylon tie-down strap safely secures load.
• Two-stage hydraulic cylinder design speeds lifting of transmission
into position for installing.
Overall
Height
Max.
(low pos.) Height
36"
73-1/2"
Leg
Width
40"
Tilt (Maximum)
Side Front Back
14° 50° 38°
HWAHW93716
• For shops with in-ground or above-the-floor vehicle hoists.
• Low height of 41-1/2" allows transmission to be rolled out from
under bus or other vehicle’s frame.
• Metered, foot-operated air pump allows effortless lifting of the
transmission into place, controlling the load precisely during
removal and installation.
• Operation is twice as fast as other jacks powered by a hand pump.
• A dedicated adapter that fits the popular Allison 500 and 600
series automatic transmissions is included with OTC5078.
• Safety bypass prevents damage caused by a system overload.
Overall
Height
(low pos.)
41-1/2"
1-800-354-0408
Max.
Height
65"
Leg
Width
46"
Tilt (Maximum)
Side Front Back
14° 50° 38°
• Four adjustable load support arms
• Wide steel frame
• Dual handle allows jack to operate
from either side
• Release valve easily
accessible for sensitive load
• Load-restraining chain is vital
for raising and lowering safely
Weight
118 lbs.
HWAHW93718
1 Ton Hydraulic Transmission Jack
OTC5078
Air-Assisted 2,000 lb. Capacity High-Lift Transmission Jack
for Trucks and Buses
Max.
Cap.
(lbs.)
2000
• Foot operated pump leaves both
hands free to maneuver transmission
• Safety overload valve prevents
overloading beyond rated capacity
• Fully adjustable universal saddle
with adjustable corner brackets
and safety chain
• Hand release valve lever aids in
making minor adjustments in raising
and lowering transmission jack
• Open style foot pumping pedal
prevents foot from slipping off pedal
while pumping hydraulic unit
• Extra wide leg base to provide
stability when moving transmission
from vehicle to work bench
Lifting Height:
Low 35-1/2"
High 72-1/2"
Base Size:
33-3/8" x 37-1/2"
Shipping Weight:
139 lbs.
PRH68000
Max.
Height
75"
OTC1791
1,000 lb. Capacity High-Lift Transmission Jack
Max.
Cap.
(lbs.)
1000
PRH68000
Telescopic Transmission Jack
1/2 Ton Capacity Single Pump
Weight
254 lbs.
OTC5078
• Wide stance tubular steel frame equipped with
four ball bearing 360° swivel casters
• Two heavy cast adjustable mounting plates
• Built in relief valves prevent overloading
• Load restraint chain is included
• Four wedges to support the load
• Forward tilt 40°
• Rearward tilt 15°
• Sideways tilt 10°
• Low height 10"
• High height 44"
• Power raise 34"
• Overall length 48"
• Overall width 29-7/8"
• Overall height 9-1/2"
HWAHW93718
7
LIFTING EQUIPMENT
SURFACE MOUNTED LIFTS
EQUVLXS10 and EQUVLXS7
Rotary® Low-Rise Lifts
• 7,000 and 10,000 lbs. capacity models are available.
• Drive-over ramps and side rails provide the width to support
wider vehicles during approach.
• Dual lifting cylinders provide the power required to lift a 10,000 lbs. vehicle.
• Includes four heat-resistant non-slip pads which provide a great contact
surface for adapters or vehicle pick-up points.
• VLXS series VersaLifts come standard with a
three-position wheel spotting dish for
accurate spotting of vehicles.
EQUVLXS10 Adapters
The new three-position adapters have rubber contact pads on
three sides increasing the positioning capabilities. The height
added by these adapters excels the versatility of the lift. The
adapters can be laid flat for 4-5/16" (110mm) additional height
or on the side for 6-5/16" (160mm). Achieve maximum extension
by laying the adapter on end and allowing an additional 8-9/16"
(218mm) of height. The VLXS10 also comes with a set of four
1-1/2" rubber block adapters for low-profile vehicles.
EQUVLXS7 Adapters
The 7,000 lb. capacity low-rise lift comes standard with a set of
rubber blocks for quick access to lower profile and unibody
frame vehicles. Blocks are 1-1/2" and 3" in height.
Model Specifications:
Rise High Step:
Rise Mid Step:
Rise Low Step:
Rise Short Pad:
Rise Flat:
Length Overall:
Width Overall:
Lift Capacity:
EQUVLXS7
24-3/4"
N/A
N/A
23-1/4"
21-3/4"
90-1/2"
78-1/2"
7,000 lbs.
EQUVLXS10
30-5/16"
28-1/16"
26-1/16"
23-1/4"
21-3/4"
90-1/2"
78-1/2"
10,000 lbs.
EQUSL210i
Rotary® Inground SmartLifts®
• Removable non-skid cover plate with a leak resistant seal allows easy access
to interior system. Fully contained polymer composite housing with
SMARTGUARD® Protection protects the entire unit from the environment. A
flexible entry boot keeps moisture from seeping between the PVC chase and
entry. Also includes a containment access hole for visual inspection.
• New patent pending LDS signals the user if moisture accumulates in the
containment and helps prevent the accumulation of water.
• Patent pending air actuated air cylinder uses stainless steel and polymer
construction for maximum corrosion resistance and service life. Locks
engage at multiple locking positions. The latch release control is conveniently
located on the easy touch control panel.
• EasyAccess™ cylinder design does not require bleeding and can be removed
for servicing while other components remain in place. All hose connections
can be accessed from floor level. (Patent Pending)
• Three-position flip-up adapters on 10,000 lb. lifts and stackable pad adapters
for 12,000 lb. lifts are perfect for cars, vans and trucks.
• Compact, low-profile super-structure features a non-skid coating for easy
drive over capability.
• Three-position wheel spotting dish.
• 8-1/2" (216 MM) guide pistons with SMARTGUARD® coating.
• Stainless steel hose fittings on equalizer bar.
SmartLift Features
• Capacities: 10,000 to 12,000 lbs
• Saves space — 11 SmartLifts fit in the
space of 10 surface lifts
• Low-profile arms great for vehicles with
low ground clearance
• No hard piping between the lift and its
power source
• Without columns, risk of vehicle damage
is eliminated, shop appearance and
employee workspace is improved.
• 60 gallons less oil than old
low-pressure inground lifts
8
Model EQUSL210i Specifications:
Rise:
81-1/4"
Width Overall:
93-1/4"
Lift Capacity:
10,000 lbs.
Drive Thru Clearance:
84-1/2"
Min. Bay Size:
11" x 24"
www.koiautoparts.com
LIFTING EQUIPMENT
SURFACE MOUNTED LIFTS
NEW
1/2" steel cable for
greater lifting capacity
Filter/regulator/lubricator for clean,
lubricated air which will extend the
life of your lift and air powered tools
Stainless steel turning
radius gauges standard
14,000 lbs. Capacity
Four-Post Lifts
A dual function Sentinel Lock™
system features a patented (U.S.
Patent No. 6,446,757) slack cable
guide arm that stays “on guard” to
manage the lock latch.
Adjustable latch bars
ensure the runways are
level when resting on the
latch bars at any of the
multiple locking positions
NEW
Longer slip plate redesigned
to accommodate four wheel
alignments up to 158"
NEW
Redesigned runways to handle
higher capacity vehicles and
longer wheelbases up to 212-1/2"
EQUSMO14
Rotary® Four-Post Surface Mounted Lifts
Specifications:
General Service
Alignment
• Adjustable latch bar ensures the runways are level
Model:
SM14
SMO14
AR14
ARO14
when resting on the latch bar at any of the multiple
locking positions.
14,000 lbs. capacity
•
•
•
•
• Molded yoke cap covers that keep debris away from
Filter/regulator/lubricator
•
•
•
•
yoke sheaves.
• Non-welded track to accommodate rolling jacks and
Open-end design
•
•
drain pans.
1/2" diameter steel cable
•
•
•
•
• Dual function sentinel lock system features a patent
Cylinder located under the runway
•
•
•
•
pending slack cable guide arm that stays “on guard”
Dual
function
Sentinel
Lock™
System
•
•
•
•
to manage the lock latch. In a slack cable situation,
Accommodates up to 212-1/2" wheelbase
•
•
•
the lock system kicks the lock into position. Fewer
parts, less opportunity for service issues and more
Stainless steel radius gauges standard
•
•
piece of mind.
Two rolling jacks standard
•
•
• Rotary® four-post general service lifts can be
Compatible with the new technology
•
•
equipped with bolt on alignment equipment.
alignment systems on the market today
All Rotary® alignment equipment is fully compatible
Optional bolt-on alignment kit available*
•
•
with the new technology alignment systems on the
*
Bolt-on
alignment
equipment
is
compatible
with
the
new
technology
alignment
equipment
on
the market today.
market today.
• Controls are mounted on the front column for
Model EQUSM014 Specifications:
technician convenience.
Rise:
73-3/4"
• Rotary® power unit located on the front column for more efficient performance.
Length Overall:
19' 2"
• Cylinder under runway eliminates any opportunity for vehicle door or mirror damage.
Width Overall:
11' 7"
• Non Skid Surface allows sure grip of tires and a “sure foot” for technicians standing on the lift.
Lift Capacity:
14,000 lbs.
• Protective strips on ramp ends eliminate floor gouging.
• More Rise — A full 73-3/4" of rise, the highest in the industry.
• Movable and replaceable rolling jack stops are made of “conveyor belt strength” rubber, giving the
technician full flexibility to limit the travel of 1 or 2 jacks.
• Cable inspection port allows a view of 100% length of the cable, an ANSI requirement.
• Filter/lubricator/regulator for clean, lubricated air which will extend the life of your lift and air powered tools.
• Automatic ramp chocks engage when the lift is raised.
1-800-354-0408
9
LIFTING EQUIPMENT
SURFACE MOUNTED LIFTS
Rotary® Twin-Post Surface Mounted Lifts
Technician Productivity Features:
• Adjustable height option on two-post
column extensions gives you flexibility
during installation to maximize the vehicles
you can service with each lift.
• The patented “Double S” (US Patent No.
5,009,287) single piece construction
column design provides a channel for the
bearings to travel that maximizes the
strength of the column and surface contact
area of the bearing.
• Slider block bearings of Tivar® 1000
polyethylene are self-lubricating and
maintenance free.
• Arm restraints make positioning of arms
easy. They engage when the lift is raised
and automatically disengage when the lift is
fully lowered.
• High-pressure cylinders in each column
provide maximum lifting force and smooth
operation.
• Overhead padded switch bar to prevent
damaging a vehicle from being raised too
high.
• Standard three-position flip-up adapters
allow for quick and easy contact with
pickup points on a variety of vehicles. We
offer the highest standard adapter reach in
the industry, often avoiding the need for
additional adapters. Low profile arm design
on all 10,000 lbs. capacity models (4" from
floor to flip-up adapter min. height)
accommodate more vehicles.
Three-Stage/Front and Two-Stage/Rear arms:
The three-stage arm increases overall arm
sweep and minimum arm reach to precisely
lift vehicles that have:
• Uni-body construction
• Visually marked pick-up points on the
vehicle
• Wider wheelbase and lower profile
• A short or long wheelbase
EQUA10i_EQUSPOA10
Rotary® Two-Post Surface Mounted Lift
10,000 lbs. Capacity
True Asymmetrical Lifts
• Columns are rotated 30°
• Places the approximate center of gravity
of the vehicle in line with the optimum
load capability of the column
• Allows maximum door opening on
passenger cars for improved access to
vehicle interior and under the dash
Operating Controls and
Power Unit Configuration —
EQUSPOA10:
• Conventional two-hand operation
• Power unit down
• Manual two-handed release locking system
EQUA10i:
inbay® Features:
• One touch controls on each column
• Power unit up and out of the way
• Integrated air/electric connections
• Tool storage rack
• Electronic locks
Model Specifications:
Rise:
78"
Overall Height: 11' 8-1/2"
Width Overall:
11' 5-1/2"
Lift Capacity:
10,000 lbs.
Drive Thru Clearance:
95-1/4"
Ceiling Height Required: 12'
Raptor lifts are manufactured to high-quality standards for years of dependable
service at a reasonable cost.
Features:
• Automatic arm restraint gears
• Large pad adapters with adapter extensions are standard. Includes four each of the
following extensions:
1.5"(38mm), 3"(76mm) and 6"(152mm)
• Durable powder coat finish
• Overhead padded switch bar to avoid vehicle damage from being raised too high
• Can lift passenger cars, trucks, and vans up to 10,000 lbs.
• Position vehicle doors in front of columns or behind to avoid door damage
• Top mounted pull design hydraulic cylinder. The rod is protected behind the
carriage to prevent damage
• Re-setting safety locks in each column
• Two full-stroke cylinders with overhead cable for equalization
• Available in blue with yellow arms and adapters
Specifications:
Model Number:
Lifting Capacity:
Rise:
Height Overall:
Width Overall:
Drive-Thru Clearance:
Width Inside Columns:
Ceiling Height Required:
Max Load Per Arm:
Min. Bay Size:
10
EQURP10
10,000 lbs.
77"
143-1/8"
133"
99"
111-3/4"
144-1/8"
2,500 lbs.
12' x 24'
www.koiautoparts.com
LIFTING EQUIPMENT
SURFACE MOUNTED LIFTS
Professional Automotive Service Two-Post Models
EQUSPOA7LC
EQUSPOA10
EQUSPO12
EQUS18i
•
•
•
•
• 10,000 lbs. Capacity
• Asymmetric Two-Post lift
• Conventional controls located
on power unit
• Two stage arms with three
position flip-up adapters
• 12,000 lbs. Capacity
• Symmetric Two-Post Lift
• Conventional controls located
on power unit
• Stackable adapters
• 18,000 lbs. Capacity
• inbay® controls and additional
features
• Adjustable height:
13'6" to 16'6"
EQUS12i
EQUTLO7
• 10,000 lbs. Capacity
• Asymmetric Two-Post lift
• inbay® controls and additional
features
• Two stage arms with three
position flip-up adapters
• 12,000 lbs. Capacity
• Symmetric two-post lift
• inbay® controls and additional
features
• Stackable adapters
• Download written specifications
and cad drawings
• 7,000 lbs. Capacity
• Symmetric two-post lift
• Conventional controls located
on power unit
• Designed to lift three and four
wheel turf maintenance
vehicles
EQUSPO10
EQUSPO15
High Capacity Four-Post Lifts
• 10,000 lbs. Capacity
• Symmetric Two-Post Lift
• Conventional controls located
on power unit
• Two stage arms with three
position flip-up adapters
• 15,000 lbs. Capacity
• Conventional controls
EQUSM18
7,000 lbs. Capacity
Asymmetric Two-Post lift
Low ceiling application
Conventional controls located
on power unit
• Two stage arms with three
position flip-up adapters
EQUA10i
EQUSPOA7LC-RA
•
•
•
•
7,000 lbs. Capacity
Asymmetric Two-Post lift
Low ceiling application
Conventional controls located
on power unit
• Includes rubber adapters
EQUSPOA82
•
•
•
•
7,000 lbs. Capacity
Asymmetric Two-Post lift
Pad contact lift
Conventional controls located
on power unit
EQUA7Pi
•
•
•
•
7,000 lbs. Capacity
Asymmetric Two-Post lift
Pad contact lift
inbay® controls and additional
features
• Two stage arms with three
position flip-up adapters
EQUS10i
• 10,000 lbs. Capacity
• Symmetric two-post lift
• inbay® controls and additional
features
• Two stage arms with
three position flip-up adapters
Axle Jacks
HWAHW93733 . . . . 3
OTC1788A . . . . . . . 3
OTC5012A . . . . . . . 3
Bottle Jacks
WLMW1621 . . . . . . 4
WLMW1623 . . . . . . 4
WLMW1625 . . . . . . 4
WLMW1628 . . . . . . 4
WLMW1632 . . . . . . 4
WLMW1633 . . . . . . 4
1-800-354-0408
Engine Stands
HWAHW93808 . . . . 6
OTC2015A . . . . . . . 6
OTC2018A . . . . . . . 6
PRH40001 . . . . . . . 6
WLMW41024 . . . . . 6
WLMW41025 . . . . . 6
WLMW41029 . . . . . 6
WLMW41030 . . . . . 6
WLMW41031 . . . . . 6
WLMW41032 . . . . . 6
WLMW41033 . . . . . 6
Floor Jacks
WLMW1612 . . . . . . 3
WLMW1614 . . . . . . 3
WLMW1616 . . . . . . 3
• 15,000 lbs. Capacity
• inbay® controls and additional
features
• Adjustable height:
13'6" to 16'6"
EQUSPO18
• 18,000 lbs. Capacity
• Conventional controls
• 18,000 lbs. Capacity
• Wheel base max:
194" to 230"
EQUSM300
• 30,000 lbs. Capacity
• 3 Models
• Wheel base max:
235" to 307"
PART NUMBER INDEX
MANUFACTURER KEY
Buffalo Tools – PAI
Clarke – CLK
Hein-Werner Automotive – HWA
Herkules – HER
OTC – OTC
Performance Tool/Wilmar – WLM
Professional Hydraulic Jacks – PRH
Raptor – EQU
Rotary Lifts – EQU
Air Jacks
HERAJ2 . . . . . . . . . 2
HERAJ3 . . . . . . . . . 2
EQUS15i
Cincinnati, OH
1-800-354-0408
www.koiautoparts.com
WLMW1618 . . . . . . 3
WLMW1620 . . . . . . 3
WLMW1630 . . . . . . 3
Garage Sets
CLKGE2001 . . . . . . 5
CLKGE2002 . . . . . . 5
PAICDOLLY . . . . . . . 5
Jack Stands
HWAHW93503 . . . . 4
HWAHW93506 . . . . 4
OTC1784C . . . . . . . 4
WLMW41021 . . . . . 4
WLMW41022 . . . . . 4
WLMW41023 . . . . . 4
Lifts
HWAHW93690 . . . . 4
OTC1545 . . . . . . . . 5
OTC1585 . . . . . . . . 5
OTC1590 . . . . . . . . 4
PRH66000 . . . . . . . 4
WLMW41035 . . . . . 5
Service Jacks
HWAHW93642 . . . . 2
HWAHW93652 . . . . 2
HWAHW93657 . . . . 2
HWAHW93660 . . . . 2
HWAHW93662 . . . . 2
OTC1505B . . . . . . . 2
OTC1510B . . . . . . . 2
OTC1739 . . . . . . . . 2
WLMW1617 . . . . . . 2
Surface Mounted Lifts
EQUA10i. . . . . 10, 11
EQUA7Pi . . . . . . . 11
EQURP10 . . . . . . . 10
EQUS10i . . . . . . . 11
EQUS12i . . . . . . . 11
EQUSL210i. . . . . . . 8
EQUSM014 . . . . . . 9
EQUSP0A10 . . 10, 11
EQUSPO10 . . . . . . 11
EQUSPO12 . . . . . . 11
EQUSPOA7CL . . . . 11
EQUSPOA7LC-RA . 11
EQUSPOA82 . . . . . 11
EQUTLO7 . . . . . . . 11
EQUVLXS10 . . . . . . 8
EQUVLXS7 . . . . . . . 8
Transmission Jacks
HWAHW93716 . . . . 7
HWAHW93718 . . . . 7
OTC1521A . . . . . . . 7
OTC1728 . . . . . . . . 7
OTC1791 . . . . . . . . 7
OTC5078 . . . . . . . . 7
PRH68000 . . . . . . . 7
11
KOI STORE LOCATIONS
For Complete Up To Date Listing Visit
KENTUCKY
Alexandria
Bellevue Refinish
Burlington
Carrollton
Crescent Springs Refin.
Crestwood
Crittenden
Cynthiana
Eminence
Falmouth
Florence
Frankfort
Georgetown
8328 East Main St
40 Donnermeyer Dr
2878 Washington St
1303 Highland Ave
611 Western Reserve
6606 W Hwy 22
203 North Main St
110 West Pleasant St
4872 Main St
135 Ridgeway Ave
7232 Burlington Pk
573 East Main St
404 North Broadway
(859) 635-2131
(859) 655-6764
(859) 586-5630
(502) 732-6961
(859) 341-6000
(502) 241-9411
(859) 428-2118
(859) 234-6710
(502) 845-2155
(859) 654-6971
(859) 371-4820
(502) 226-4400
(502) 863-1940
Independence
Lexington AE
Lexington
Lexington Refinish
Lexington Southside
Louisville
Louisville - Dixie Hwy
Mt. Sterling
Newport
Nicholasville
Owenton
Paris
Warsaw
Williamstown
11399 Taylor Mill Rd
117 Westhampton Dr
1105 Winchester Rd
1141 Commercial Dr
211 Rosemont Garden
4001 Produce Rd
6801 Dixie Hwy
537 Maysville Rd
412 Central Ave
1038 N. Main St
318 North Main St
1470 South Main St
502 East Main St
1003 North Main St
(859) 356-1500
(859) 233-2199
(859) 252-6111
(859) 231-8359
(859) 278-0574
(502) 969-5300
(502) 937-7317
(859) 498-4400
(859) 431-0309
(859) 881-3000
(502) 484-3423
(859) 987-5318
(859) 567-5551
(859) 824-4451
3218 Marshall Dr
122 East Main St
11180 Luschek Dr
127 North Main St
1417 Central Pkwy
3500 Harrison Ave
8282 Colerain Ave
8270 Colerain Ave
4301 Montgomery Rd
5101 Crookshank Rd
2200 Valley St.
7557 Brandt Pike
4901 Dixie Hwy
11843 Kemper Springs
1291 East 2nd St
624 Maple Ave
611 Maple Ave
980 Main St
(513) 753-5332
(937) 783-2444
(513) 530-0072
(419) 358-4000
(513) 241-7542
(513) 661-2400
(513) 741-0060
(513) 741-7474
(513) 458-3300
(513) 921-6000
(937) 233-5481
(937) 236-0100
(513) 829-1800
(513) 648-3020
(937) 746-3613
(513) 896-4000
(513) 887-2468
(513) 869-7044
Harrison
Lebanon
Lima
Lockland
Loveland
Mariemont
Middletown
Middletown Refinish
Milford
Mt. Carmel
Mt. Carmel Refinish
Mt. Washington
New Carlisle
Pisgah
Seven Hills
Sharonville Refinish
Springfield
St. Marys
Toledo
1378 Stone Rd
650 Columbus Ave
700 North Main St
105 Mill St
209 Loveland Madeira
4300 Plainville Rd
1426 Central Ave
2445 North Verity Pkwy
919 State Rt. 28
665 Batavia Pike
665 Batavia Pike
7109 Salem Rd
2432 S Dayton Lakeview
8120 Regal Lane
2222 Seven Hills Dr
11598 Lebanon Rd
622 West Main St
302 East Spring St
5411 Roan Road
(513) 367-5500
(513) 932-6065
(419) 228-1221
(513) 761-9494
(513) 683-1793
(513) 271-0343
(513) 422-5525
(513) 424-1801
(513) 248-0660
(513) 528-7050
(513) 528-7072
(513) 231-6883
(937) 849-1578
(513) 777-7754
(513) 825-2203
(513) 769-4500
(937) 323-5585
(419) 394-4156
(419) 824-2143
721 Main St
601 Saint Clair St
2528 Craigmont Ave
129 South 8th Street
(765) 647-4121
(812) 537-2335
(812) 273-1501
(765) 962-9546
OHIO
Amelia
Blanchester
Blue Ash
Bluffton
Cincinnati
Cincinnati - Cheviot
Cincinnati - Colerain Ref
Cincinnati - Colerain
Cincinnati - Norwood
Cincinnati - West. Hills
Dayton
Dayton - Huber Heights
Fairfield
Forest Park
Franklin
Hamilton
Hamilton Refinish
Hamilton Westside
INDIANA
Brookville
Lawrenceburg
Madison
Richmond
Proud Member of
Federated Auto Parts
www.KOIAUTOPARTS.com
WEST VIRGINIA
Charleston
1430 Pennsylvania Ave
(304) 342-9920
IMPORT • COLLISION • TOOL • ACCESSORIES • MOBILE
KOI Accessories
Collision/Bumper Recon
Equipment & Tool
KOI Import Parts
AE
GROUP
AUTOMOTIVE
PARTS SERVICE
2701 Spring Grove
3300 Spring Grove
3300 Spring Grove
11574 Gondola St
HAMLET
AUTO PARTS
(513) 357-2599
(513) 287-7500
(513) 542-4800
(513) 771-7777
JOHNS
AUTO PARTS
KENTUCKY
MOTOR SERVICE
Battery Truck
Chemical Truck
Detail Truck
Tool Truck
SAVAGE
AUTO PARTS
2701 Spring Grove Ave.
1330 Arlington Ave.
1330 Arlington Ave.
1330 Arlington Ave.
SIFERD
HOSSELLMAN CO.
(513) 505-3610
(513) 476-6635
(513) 310-1429
(513) 310-3590
SPRINGFIELD
AUTO PARTS
“The Official Auto Parts Store of The Cincinnati Reds“
w w w. KO I AU TOPARTS.com • 1-800-354-0408
WILCOX
AUTO PARTS