1. technology and computing
2. technical support

April/14/2015
errata_c17w15_21
S1C17 Family Technical Manual Errata
ITEM
The operation when “Display Off” is selected
Object manual
Document code
Object item
Page
S1C17M01 Technical Manual
412361701
17.5.2 Display On/Off
17-6
S1C17W22/W23 Technical Manual
412690402
18.5.2 Display On/Off
18-7
S1C17W15 Technical Manual
412645702
17.5.2 Display On/Off
17-6
S1C17W14/W16 Technical Manual
412910300
18.5.2 Display On/Off
18-6
(Error)
When “Display off” is selected, the drive voltage supply stops and the LCD driver pin outputs are all set to VSS
level.
Since “All on” and “All off” directly control the driving waveform output by the LCD driver, data in the display
data RAM is not altered. The common pins are set to dynamic drive for “All on” and to static drive for “All off.”
This function can be used to make the display flash on and off without altering the display memory.
(Correct)
When “Display off” is selected, the drive voltage supply stops and the LCD driver pin outputs are all set to VSS
level.
Since “All on” and “All off” directly control the driving waveform output by the LCD driver, data in the display
data RAM is not altered. The common pins are set to dynamic drive for “All on” and to static drive for “All off.”
This function can be used to make the display flash on and off without altering the display memory.
Note:
When “Display off” is selected, VC4 ( or VC3)’s electric charge must be discharged with the procedure shown
below.
<Using Internal Generation Mode>
1.
Set the LCD8PWR.VCEN bit to 0. (Disable LCD voltage regulator)
2.
Set the LCD8PWR.HVLD bit to 1. (Enable heavy load protection mode)
3.
When CLK_LCDxx is stopped, it must be stopped after VC4 ( or VC3 )’s electric potential became less
than VDD – 1V.
<Using External Voltage Application Mode>
1.
Disable the external voltage.
2.
Set the LCD8PWR.HVLD bit to 1. (Enable heavy load protection mode)
3.
When CLK_LCDxx is stopped, it must be stopped after VC4 ( or VC3 )’s electric potential became less
April/14/2015
errata_c17w15_21
than VDD – 1V.
When “Display on” is selected again, it should be in a reverse procedure of the above description.
Nov/14/2014
errata_c17w15_20
S1C17 Family Technical Manual Errata
ITEM
Slave Operation in 10-bit Address Mode
Object manual
Document code
Object item
Page
S1C17M01 Technical Manual
412361700
Slave Operations in 10-bit Address
13-14
Mode
S1C17F13 Technical Manual
412486300
Slave Operations in 10-bit Address
12-14
Mode
S1C17W22/W23 Technical Manual
412690401
Slave Operations in 10-bit Address
14-14
Mode
S1C17W15 Technical Manual
412645701
Slave Operations in 10-bit Address
14-14
Mode
(Error)
Figure：Example of Data Transfer Starting Operations in 10-bit Address Mode(Slave Mode)
(Correct)
Figure： Example of Data Transfer Starting Operations in 10-bit Address Mode(Slave Mode)
Nov/14/2014
errata_c17w15_19
S1C17 Family Technical Manual Errata
ITEM
CLG OSC3A Control Register
Object manual
Document code
Object item
Page
S1C17M01 Technical Manual
412361700
Overview, Input Pin
10-1
S1C17F13 Technical Manual
412486300
Overview, Input Pin
9-1
S1C17W22/W23 Technical Manual
412690401
Overview, Input Pin
11-1
S1C17W15 Technical Manual
412645701
Overview, Input Pin
11-1
(Error)
Overview
Figure：Configuration of a T16 Channel
(Correct)
Overview
Figure：Configuration of a T16 Channel
Nov/14/2014
errata_c17w15_19
(Error)
Input Pin
(Correct)
Nov/14/2014
errata_c17w15_18
S1C17 Family Technical Manual Errata
ITEM
16-bit Timers (T16)
Object manual
Document code
Object item
Page
S1C17M01 Technical Manual
412361700
Control Registers
10-5
S1C17F13 Technical Manual
412486300
Control Registers
9-5
S1C17W22/W23 Technical Manual
412690401
Control Registers
11-5
S1C17W15 Technical Manual
412645701
Control Registers
11-5
(Error)
T16 Ch.n Mode Register ： Bit0
TRMD
This bit selects the T16 operation mode.
1 (R/W): One-shot mode
0 (R/W): Repeat mode
For detailed information on the operation mode, refer to “Operations in One-shot Mode” and
“Operations in Repeat Mode.”
(Correct)
T16 Ch.n Mode Register ： Bit0
TRMD
This bit selects the T16 operation mode.
1 (R/W): One-shot mode
0 (R/W): Repeat mode
For detailed information on the operation mode, refer to “Operations in One-shot Mode” and
“Operations in Repeat Mode.”
Note: When one-shot mode is set, the T16_nTR.TR[15:0] bits should be set to a value equal to or
greater than 0x0001.
Nov/14/2014
errata_c17w15_17
S1C17 Family Technical Manual Errata
ITEM
16-bit Timers (T16)
Object manual
Document code
Object item
Page
S1C17M01 Technical Manual
412361700
Overview, Input Pin
10-1
S1C17F13 Technical Manual
412486300
Overview, Input Pin
9-1
S1C17W22/W23 Technical Manual
412690401
Overview, Input Pin
11-1
S1C17W15 Technical Manual
412645701
Overview, Input Pin
11-1
(Error)
Overview
Figure：Configuration of a T16 Channel
(Correct)
Overview
(Error)
Input Pin
Figure：Configuration of a T16 Channel
Nov/14/2014
errata_c17w15_17
If the port is shared with the EXCLm pin and other functions, the EXCLm input function must be
assigned to the port before using the event counter function. The EXCLm signal can be input through
the chattering filter. For more information, refer to the “I/O Ports” chapter.
(Correct)
Input Pin
If the port is shared with the EXCLm pin and other functions, the EXCLm input function must be
assigned to the port before using the event counter function. For more information, refer to the “I/O
Ports” chapter.
Nov/14/2014
errata_c17w15_16
S1C17 Family Technical Manual Errata
ITEM Electrical Characteristics
EXOSC external clock input characteristics
Object manual
Document
Object item
Page
code
S1C17W22/W23 Technical Manual
412690401
23.5
Clock
Generator
(CLG)
23-6
Generator
(CLG)
20-6
Characteristics
S1C17W15 Technical Manual
412645701
20.5
Clock
Characteristics
(Error)
(Correct)
Nov/14/2014
errata_c17w15_16
ITEM Electrical Characteristics
R/F Converter (RFC) Characteristics
Object manual
Document
Object item
Page
code
S1C17W22/W23 Technical Manual
412690401
23.13
R/F
Converter
(RFC)
23-16
Converter
(RFC)
20-16
Characteristics
S1C17W15 Technical Manual
412645701
20.13
R/F
Characteristics
(Error)
(Correct)
Nov/14/2014
errata_c17w15_16
ITEM
Electrical Characteristics
Object manual
Input/Output Port (PPORT) Characteristics
Document
Object item
Page
23.7 Input/Output Port (PPORT)
23-7
code
S1C17W22/W23 Technical Manual
412690401
Characteristics
S1C17W15 Technical Manual
412645701
20.7 Input/Output Port (PPORT)
20-7
Characteristics
Page
23-7
S1C17W22/W23 Technical Manual
23.7 Input/Output Port (PPORT) Characteristics
(Error)
(Correct)
Page
20-7
S1C17W15 Technical Manual
20.7 Input/Output Port (PPORT) Characteristics
Nov/14/2014
errata_c17w15_16
(Error)
(Correct)
Nov/7/2014
errata_c17w15_15
S1C17 Family Technical Manual Errata
ITEM
Mounting Precautions
Object manual
Document code
Object item
Page
S1C17M01 Technical Manual
412361700
Mounting Precautions
AP-C-1
S1C17F13 Technical Manual
412486300
Mounting Precautions
AP-C-1
S1C17W22/W23 Technical Manual
412690401
Mounting Precautions
AP-C-1
S1C17W15 Technical Manual
412645701
Mounting Precautions
AP-C-1
(Error)
VPP pin
Connect CVPP to this pin if the VPP voltage is not stable.
(Correct)
VPP pin
If fluctuations in the Flash programming voltage VPP is large, connect a capacitor CVPP between the VSS
and VPP pins to suppress fluctuations within VPP ± 1 V. The CVPP should be placed as close to the VPP
pin as possible and use a sufficiently thick wiring pattern that allows current of several tens of mA to
flow.
V PP pin connection example
Pin
V PP
CVPP
V SS
Pin
V PP
CVPP
V SS
Nov/7/2014
errata_c17w15_14
S1C17 Family Technical Manual Errata
ITEM
Basic External Connection Diagram
Object manual
Document code
Object item
Page
S1C17W22/W23 Technical Manual
412690401
Basic External Connection Diagram
24-3
S1C17W15 Technical Manual
412645701
Basic External Connection Diagram
21-2
(Error)
Symbol
Name
Recommended components
…
…
…
X’tal3
Crystal resonator
CA-301 (1 MHz) manufactured by Seiko Epson Corporation
…
…
…
(Correct)
Symbol
Name
Recommended components
…
…
…
X’tal3
Crystal resonator
CA-301 (4 MHz) manufactured by Seiko Epson Corporation
…
…
…
Nov/7/2014
errata_c17w15_13
S1C17 Family Technical Manual Errata
ITEM
Supply Voltage Detector (SVD)
Object manual
Document code
Object item
Page
S1C17M01 Technical Manual
412361700
Operations, Control Registers
9-3, 9-7
S1C17F13 Technical Manual
412486300
Operations, Control Registers
8-3, 8-7
S1C17W22/W23 Technical Manual
412690401
Operations, Control Registers
10-3, 10-7
S1C17W15 Technical Manual
412645701
Operations, Control Registers
10-3, 10-7
(Error)
Reading detection results
The following two detection results can be obtained by reading the SVDINTF.SVDDT bit:
• Power supply voltage (VDD or EXSVD) ≥ Comparison voltage when SVDINTF.SVDDT bit = 0
• Power supply voltage (VDD or EXSVD) < Comparison voltage when SVDINTF.SVDDT bit = 1
Before reading the SVDINTF.SVDDT bit, wait for at least SVD circuit enable response time after 1 is
written to the SVDCTL.MODEN bit (refer to “Supply Voltage Detector Characteristics, SVD circuit enable
response time tSVDEN” in the “Electrical Characteristics” chapter). After the SVDCTL.SVDC[4:0] bits
setting value is altered to change the comparison voltage when the SVDCTL.MODEN bit = 1, wait for at
least SVD circuit response time before reading the SVDINTF.SVDDT bit (refer to “Supply Voltage
Detector Characteristics, SVD circuit response time tSVD” in the “Electrical Characteristics”chapter).
(Correct)
Reading detection results
The following two detection results can be obtained by reading the SVDINTF.SVDDT bit:
• Power supply voltage (VDD or EXSVD) ≥ SVD detection voltage VSVD when SVDINTF.SVDDT bit = 0
• Power supply voltage (VDD or EXSVD) < SVD detection voltage VSVD when SVDINTF.SVDDT bit = 1
Before reading the SVDINTF.SVDDT bit, wait for at least SVD circuit enable response time after 1 is
written to the SVDCTL.MODEN bit (refer to “Supply Voltage Detector Characteristics, SVD circuit enable
response time tSVDEN” in the “Electrical Characteristics” chapter). After the SVDCTL.SVDC[4:0] bits
setting value is altered to change the SVD detection voltage VSVD when the SVDCTL.MODEN bit = 1,
wait for at least SVD circuit response time before reading the SVDINTF.SVDDT bit (refer to “Supply
Voltage Detector Characteristics, SVD circuit response time tSVD” in the “Electrical
Characteristics”chapter).
(Error)
Bit 8 SVDDT
The power supply voltage detection results can be read out from this bit.
Nov/7/2014
errata_c17w15_13
1 (R): Power supply voltage (VDD or EXSVD) < comparison voltage
0 (R): Power supply voltage (VDD or EXSVD) ≥ comparison voltage
(Correct)
Bit 8 SVDDT
The power supply voltage detection results can be read out from this bit.
1 (R): Power supply voltage (VDD or EXSVD) < SVD detection voltage VSVD
0 (R): Power supply voltage (VDD or EXSVD) ≥ SVD detection voltage VSVD
Sep/11/2014
errata_c17w15_12
S1C17 Family Technical Manual Errata
ITEM
OSC3 oscillator circuit characteristics
Object manual
Document
Object item
Page
code
S1C17W22/W23 Technical Manual
412690401
23 Electrical Characteristics
23-6
S1C17W15 Technical Manual
412645701
20 Electrical Characteristics
20-6
(Error)
(Correct)
0x3
0x3
0x2
0x2
0x1
0x1
0x0
0x0
Sep/11/2014
errata_c17w15_11
S1C17 Family Technical Manual Errata
ITEM
I/O Cell
Object manual
Document
Object item
Page
1.3.3 Pin Descriptions
1-9
code
S1C17W15 Technical Manual
412645701
(Error)
Over voltage tolerant fail-safe type I/O cell ports:
P0[6:4], P1[7:0], P2[7:0], P3[7:0](except S1C17V07), PD[2:0]
Standard I/O cell ports:
P0[3:0], PD[4:3]
(Correct)
Over voltage tolerant fail-safe type I/O cell ports:
P2[7:0]
Standard I/O cell ports:
P0[6:0], P1[7:0], P3[7:0](except S1C17V07) , PD[4:0]
Sep/11/2014
errata_c17w15_10
S1C17 Family Technical Manual Errata
ITEM
Supply Voltage Detector (SVD) Characteristics
Object manual
Document
Object item
Page
code
S1C17W22/W23 Technical Manual
412690401
23 Electrical Characteristics
23-9
S1C17W15 Technical Manual
412645701
20 Electrical Characteristics
20-9
(Error)
(Correct)
SVDCTL.SVDC[4:0]
0x1e
Aug/28/2014
errata_c17w15_9
S1C17 Family Technical Manual errata
ITEM: Port Input / Output Control
Object manuals
Document codes
Items
Pages
S1C17M01 Technical Manual
412361700
6.4.2 Port Input / Output Control
P.6-5
S1C17F13 Technical Manual
412486300
6.4.2 Port Input / Output Control
P.6-5
S1C17W22/W23
412690401
6.4.2 Port Input / Output Control
P.6-5
412645701
6.4.2 Port Input / Output Control
P.6-5
Technical Manual
S1C17W15 Technical Manual
(Error)
Reading input data from a GPIO port
The data (1 = high input, 0 = low input) input from the Pxy pin can be read out from the
PxDAT.PxINy bit.
(Correct)
Reading input data from a GPIO port
The data (1 = high input, 0 = low input) input from the Pxy pin can be read out from the
PxDAT.PxINy bit.
Note: PxDAT.PxINy bits retain the input port state before 1 CLK that CPU reads
(Error)
Chattering filter function
(Skip)
2
Input sampling time = ———————————————— [second] (Eq.6.2)
CLK_PPORT frequency [Hz]
(Correct)
Chattering filter function
(Skip)
2~3
Input sampling time = ———————————————— [second] (Eq.6.2)
CLK_PPORT frequency [Hz]
July/30/2014
errata_c17w15_8
S1C17 Family Technical Manual errata
ITEM:
PWG2 Auto mode operations
Object manuals
S1C17W22/W23
Technical
Document codes
Items
Pages
412690401
2.1.3 Operations
2-3
412645701
2.1.3 Operations
2-3
Manual
S1C17W15 Technical Manual
(Error)
4. When the slp instruction is executed in normal mode (only OSC1 operates during SLEEP)
After a lapse of 1 ms from transition to SLEEP mode, the hardware switches from normal mode to economy
mode and sets the PWGINTF.MODCMPIF bit to 1.
(Correct)
4. When the slp instruction is executed in normal mode (only OSC1 operates during SLEEP)
After a lapse of 1 ms from transition to SLEEP mode, the hardware switches from normal mode to economy
mode and sets the PWGINTF.MODCMPIF bit to 1.
Note: The IC does not enter economy mode if a clock source other than OSC1 is active when the
slp instruction is executed. Therefore, stop clock sources other than OSC1 before executing
the slp instruction.
July/30/2014
errata_c17w15_7
S1C17 Family Technical Manual Errata
ITEM
16-bit PWM Timers(T16B)
Object manual
T16B Ch.n Compare/Capture m Data Register
Document
Object item
Page
15 16-bit PWM Timers(T16B)
15-30
Appendix A List of Peripheral
AP-A-16
Circuit Control Registers
AP-A-17
code
S1C17W22/W23 Technical Manual
412690401
AP-A-18
AP-A-19
S1C17W15 Technical Manual
412645701
15 16-bit PWM Timers(T16B)
15-30
Appendix A List of Peripheral
AP-A-15
Circuit Control Registers
AP-A-16
AP-A-17
(Error)
15.6 Control Register
(Correct)
15.6 Control Register
(Error)
Appendix A
(Common)
July/30/2014
errata_c17w15_7
(S1C17W23 only)
(Correct)
Appendix A
(Common)
(S1C17W23 only)
July/30/2014
errata_c17w15_6
S1C17 Family Technical Manual Errata
ITEM
OSC3 oscillator circuit characteristics
Object manual
Document
Object item
Page
code
S1C17W22/W23 Technical Manual
412690401
23 Electrical Characteristics
23-5
S1C17W15 Technical Manual
412645701
20 Electrical Characteristics
20-5
(Error)
OSC3 oscillator circuit characteristics
(Correct)
OSC3 oscillator circuit characteristics
July/30/2014
errata_c17w15_5
S1C17 Family Technical Manual Errata
Item
Watchdog Timer (WDT) NMI function
Object Manual
Document Code
Object Item
Page
S1C17W15 Technical Manual
412645701
8.1 Overview
8-1
S1C17W22/W23 Technical Manual
412690401
8.1 Overview
8-1
S1C17M01 Technical Manual
412361700
7.1 Overview
7-1
S1C17F13 Technical Manual
412486300
7.1 Overview
7-1
(Error)
WDT restarts the system if a problem occurs, such as when the program cannot be executed normally.
The features of WDT are listed below.
• Includes a 10-bit up counter to count NMI/reset generation cycle.
• A counter clock source and clock division ratio are selectable.
• Counter overflow generates a reset or NMI.
Figure 8.1.1 shows the configuration of WDT.
(Correct)
WDT restarts the system if a problem occurs, such as when the program cannot be executed normally.
The features of WDT are listed below.
• Includes a 10-bit up counter to count NMI/reset generation cycle.
• A counter clock source and clock division ratio are selectable.
• Counter overflow generates a reset or NMI.
Internal data bus
Figure 8.1.1 shows the configuration of WDT.
Clock
Generator
WDT
WDTRUN[3:0]
WDTCNTRST
CLK_WDT
CLKSRC[1:0]
CLKDIV[1:0]
DBRUN
10-bit counter
Reset
request
July/30/2014
errata_c17w15_5
Object Manual
Document Code
Object Item
Page
S1C17W15 Technical Manual
412645701
8.3.1 WDT Control
8-2
S1C17W22/W23 Technical Manual
412690401
8.3.1 WDT Control
8-2
S1C17M01 Technical Manual
412361700
7.3.1 WDT Control
7-2
S1C17F13 Technical Manual
412486300
7.3.1 WDT Control
7-2
(Error)
WDT should be initialized and started up with the procedure listed below.
1. Write 0x0096 to the MSCPROT.PROT[15:0] bits.
(Remove system protection)
2. Configure the WDT operating clock.
3. Configure the WDTCTL.NMIXRST bit.
(Select NMI or reset mode)
4. Write 1 to the WDTCTL.WDTCNTRST bit.
(Reset WDT counter)
5. Write a value other than 0xa to the WDTCTL.WDTRUN[3:0] bits.
(Start up WDT)
6. Write a value other than 0x0096 to the MSCPROT.PROT[15:0] bits.
(Set system protection)
(Correct)
WDT should be initialized and started up with the procedure listed below.
1. Write 0x0096 to the MSCPROT.PROT[15:0] bits.
(Remove system protection)
2. Configure the WDT operating clock.
3. Configure the WDTCTL.NMIXRST bit.
3. Write 1 to the WDTCTL.WDTCNTRST bit.
(Select NMI or reset mode)
(Reset WDT counter)
4. Write a value other than 0xa to the WDTCTL.WDTRUN[3:0] bits.
(Start up WDT)
5. Write a value other than 0x0096 to the MSCPROT.PROT[15:0] bits.
(Set system protection)
July/30/2014
errata_c17w15_5
Object Manual
Document Code
Object Item
Page
S1C17W15 Technical Manual
412645701
8.3.1 WDT Control
8-2
S1C17W22/W23 Technical Manual
412690401
8.3.1 WDT Control
8-2
S1C17M01 Technical Manual
412361700
7.3.1 WDT Control
7-2
S1C17F13 Technical Manual
412486300
7.3.1 WDT Control
7-2
(Error)
WDT generates a system reset (WDTCTL.NMIXRST bit = 0) or NMI (WDTCTL.NMIXRST bit = 1) when the
counter overflows. To avert system restart by WDT, its embedded counter must be reset periodically via software
while WDT is running.
(Correct)
WDT generates a system reset (WDTCTL.NMIXRST bit = 0) or NMI (WDTCTL.NMIXRST bit = 1) when the
counter overflows. To avert system restart by WDT, its embedded counter must be reset periodically via software
while WDT is running.
July/30/2014
errata_c17w15_5
Object Manual
Document Code
Object Item
Page
S1C17W15 Technical Manual
412645701
8.3.1 WDT Control
8-2
S1C17W22/W23 Technical Manual
412690401
8.3.1 WDT Control
8-2
S1C17M01 Technical Manual
412361700
7.3.1 WDT Control
7-2
S1C17F13 Technical Manual
412486300
7.3.1 WDT Control
7-2
(Error)
A location should be provided for periodically processing this routine. Process this routine within the tWDT
cycle. After resetting, WDT starts counting with a new NMI/reset generation cycle.
If WDT is not reset within the tWDT cycle for any reason, the CPU is switched to interrupt processing by NMI
or reset, the interrupt vector is read out, and the interrupt handler routine is executed.
If the counter overflows and generates an NMI without WDT being reset, the WDTCTL.STATNMI bit is set to 1.
(Correct)
A location should be provided for periodically processing this routine. Process this routine within the tWDT
cycle. After resetting, WDT starts counting with a new NMI/reset generation cycle.
If WDT is not reset within the tWDT cycle for any reason, the CPU is switched to interrupt processing by NMI
or reset, the interrupt vector is read out, and the interrupt handler routine system reset is executed.
If the counter overflows and generates an NMI without WDT being reset, the WDTCTL.STATNMI bit is set to 1.
July/30/2014
errata_c17w15_5
Object Manual
Document Code
Object Item
Page
S1C17W15 Technical Manual
412645701
8.3.2 Operations in HALT and SLEEP Modes
8-2
S1C17W22/W23 Technical Manual
412690401
8.3.2 Operations in HALT and SLEEP Modes
8-2
S1C17M01 Technical Manual
412361700
7.3.2 Operations in HALT and SLEEP Modes
7-2
S1C17F13 Technical Manual
412486300
7.3.2 Operations in HALT and SLEEP Modes
7-2
(Error)
During HALT mode
WDT operates in HALT mode. HALT mode is therefore cleared by an NMI or reset if it continues for more than the
NMI/reset generation cycle and the NMI or reset handler is executed. To disable WDT in HALT mode, stop WDT by
writing 0xa to the WDTCTL.WDTRUN[3:0] bits before executing the halt instruction. Reset WDT before resuming
operations after HALT mode is cleared.
During SLEEP mode
WDT operates in SLEEP mode if the selected clock source is running. In this case SLEEP mode is cleared by an NMI
or reset if it continues for more than the NMI/reset generation cycle and the NMI or reset handler is executed.
Therefore, stop WDT by setting the WDTCTL.WDTRUN[3:0] bits before executing the slp instruction.
If the clock source stops in SLEEP mode, WDT stops. To prevent generation of an unnecessary NMI or reset after
clearing SLEEP mode, reset WDT before executing the slp instruction. WDT should also be stopped as required
using the WDTCTL.WDTRUN[3:0] bits.
(Correct)
During HALT mode
WDT operates in HALT mode. HALT mode is therefore cleared by an NMI or reset if it continues for more than the
NMI/reset generation cycle and the NMI or reset handler is executed. To disable WDT in HALT mode, stop WDT by
writing 0xa to the WDTCTL.WDTRUN[3:0] bits before executing the halt instruction. Reset WDT before resuming
operations after HALT mode is cleared.
During SLEEP mode
WDT operates in SLEEP mode if the selected clock source is running. In this case SLEEP mode is cleared by an NMI
or reset if it continues for more than the NMI/reset generation cycle and the NMI or reset handler is executed.
Therefore, stop WDT by setting the WDTCTL.WDTRUN[3:0] bits before executing the slp instruction.
If the clock source stops in SLEEP mode, WDT stops. To prevent generation of an unnecessary NMI or reset after
clearing SLEEP mode, reset WDT before executing the slp instruction. WDT should also be stopped as required
using the WDTCTL.WDTRUN[3:0] bits.
July/30/2014
errata_c17w15_5
Object Manual
Document
Object Item
Page
Code
S1C17W15 Technical Manual
S1C17W22/W23
Technical
412645701
412690401
Manual
S1C17M01 Technical Manual
S1C17F13 Technical Manual
412361700
412486300
8.4 Control Registers
8-3, 8-4,
Appendix A
P-AP-4
List of Peripheral Circuit Control Registers
8.4 Control Registers
8-3, 8-4
Appendix A
P-AP-4
List of Peripheral Circuit Control Registers
7.4 Control Registers
7-2
Appendix A
P-AP-4
List of Peripheral Circuit Control Registers
7.4 Control Registers
7-3, 7-4
Appendix A
P-AP-3
List of Peripheral Circuit Control Registers
(Error)
Bits 15–10
Reserved
Bit 9
NMIXRST
This bit sets the WDT operating mode.
1 (R/WP): NMI mode
0 (R/WP): Reset mode
This bit is used to select whether an NMI signal or a reset signal is output when WDT has not been
reset within the NMI/reset generation cycle.
Bit 8
STATNMI
This bit indicates that a counter overflow and NMI have occurred.
1 (R): NMI (counter overflow) occurred
0 (R): NMI not occurred
When the NMI generation function of WDT is used, read this bit in the NMI handler routine to confirm
that WDT was the source of the NMI.
The STATNMI set to 1 is cleared to 0 by resetting WDT.
Bits 7–5
(Correct)
Register name
WDTCTL
Bits 15-5
Reserved
Bit
Bit name
Initial
Reset
R/W
15-5
4
3-0
WDTCNTRST
WDTRUN[3:0]
0x000
0
0xa
H0
H0
R
WP
R/WP
Reserved
Remarks
Always set to 0
Always read as 0
-
July/30/2014
errata_c17w15_5
Object Manual
Document Code
Object Item
Page
S1C17W15 Technical Manual
412645701
1.1 Features
1-1
S1C17W22/W23 Technical Manual
412690401
1.1 Features
1-1
S1C17M01 Technical Manual
412361700
1.1 Features
1-1
S1C17F13 Technical Manual
412486300
1.1 Features
1-2
(誤)
(正)
Timers
Watchdog Timer (WDT)
Generates NMI or watchdog timer reset.
July/30/2014
errata_c17w15_5
Object Manual
Document Code
Object Item
Page
S1C17W15 Technical Manual
412645701
2.4.2 Transition between Operating Modes
2-15
S1C17W22/W23 Technical Manual
412690401
2.4.2 Transition between Operating Modes
2-15
S1C17M01 Technical Manual
412361700
2.4.2 Transition between Operating Modes
2-11
S1C17F13 Technical Manual
412486300
2.4.2 Transition between Operating Modes
2-12
(Error)
Canceling HALT or SLEEP mode
The conditions listed below generate the HALT/SLEEP cancelation signal to cancel HALT or SLEEP mode and
put the CPU into RUN mode. This transition is executed even if the CPU does not accept the interrupt request.
• Interrupt request from a peripheral circuit
• NMI from the watchdog timer
• Debug interrupt
• Reset request
(Correct)
Canceling HALT or SLEEP mode
The conditions listed below generate the HALT/SLEEP cancelation signal to cancel HALT or SLEEP mode and
put the CPU into RUN mode. This transition is executed even if the CPU does not accept the interrupt request.
• Interrupt request from a peripheral circuit
• NMI from the watchdog timer
• Debug interrupt
• Reset request
July/30/2014
errata_c17w15_5
Object Manual
Document Code
Object Item
Page
S1C17W15 Technical Manual
412645701
5.1 Overview
5-1
S1C17W22/W23 Technical Manual
412690401
5.1 Overview
5-1
S1C17M01 Technical Manual
412361700
5.1 Overview
5-1
S1C17F13 Technical Manual
412486300
5.1 Overview
5-1
(Error)
(Correct)
July/30/2014
errata_c17w15_5
Object Manual
Document Code
Object Item
Page
S1C17W15 Technical Manual
412645701
5.2 Vector Table
5-1
S1C17W22/W23 Technical Manual
412690401
5.2 Vector Table
5-1
S1C17M01 Technical Manual
412361700
5.2 Vector Table
5-1
S1C17F13 Technical Manual
412486300
5.2 Vector Table
5-1
(Error)
(Correct)
2 (0x02)
TTBR + 0x08
NMI
-
4
July/30/2014
errata_c17w15_5
Object Manual
Document Code
Object Item
Page
S1C17W15 Technical Manual
412645701
5.2 Vector Table
5-3
S1C17W22/W23 Technical Manual
412690401
5.2 Vector Table
5-3
S1C17M01 Technical Manual
412361700
5.2 Vector Table
5-3
S1C17F13 Technical Manual
412486300
5.2 Vector Table
5-3
(Error)
*2 Either reset or NMI can be selected as the watchdog timer interrupt with software.
(Correct)
*2 Either reset or NMI can be selected as the watchdog timer interrupt with software.
July/30/2014
errata_c17w15_5
Object Manual
Document Code
Object Item
Page
S1C17W15 Technical Manual
412645701
5.5 NMI
5-4
S1C17W22/W23 Technical Manual
412690401
5.5 NMI
5-4
S1C17M01 Technical Manual
412361700
5.5 NMI
5-4
S1C17F13 Technical Manual
412486300
5.5 NMI
5-4
(Error)
The watchdog timer embedded in this IC can generate a non-maskable interrupt (NMI). This interrupt takes precedence
over other interrupts and is unconditionally accepted by the CPU.
For detailed information on generating NMI, refer to the “Watchdog Timer” chapter.
(Correct)
This IC cannot generate non-maskable interrupt (NMI).
Jul/4/2014
errata_c17w15_4
S1C17 Family Technical Manual Errata
ITEM
Unused pins
Object manual
Document
Object item
Page
Appendix C Mounting Precautions
AP-C-2
code
S1C17W15 Technical Manual
412645701
(Error)
Unused pins
(4) CV1–2 pins
If super economy mode is not used, these pins should be left open.
(Correct)
Unused pins
(4) CV1–2 and VD2 pins
If super economy mode is not used, the CV1 and CV2 pins should be left open. In this case, CPW3 can be
omitted by connecting between the VDD and VD2 pins directly. When these pins are not short-circuited,
CPW3 is required even if super economy mode is not used.
Mar/12/2014
errata_c17w15_3
S1C17 Family Technical Manual Errata
ITEM
SYSCLK switching function at wake-up
Object manual
Document code
Object item
Page
S1C17W15 Technical Manual
412645701
2.6 Control Register
2-18
(Addition)
Addition to the Explanation of WUPMD bit
Note: ・When the CLGSCLK.WUPMD bit = 1, the clock source enable bits (CLGOSC.EXOSCEN,
CLGOSC.OSC1EN, CLGOSC.IOSCEN) except for the SYSCLK source selected by the
CLGSCLK.CLKSRC[1:0] bits will be cleared to 0 to stop the clocks after a system wake-up.
However, the enable bit of the clock source being operated during SLEEP mode by setting
the CLGOSC.****SLPC bit retains 1 after a wake-up.
・When the CLGSCLK.WUPMD bit = 1, Setting the same CLGSCLK.WUPSRC[1:0] bits and
CLGSCLK.WUPDIV[1:0] bits as CLGSCLK.CLKSRC[1:0] bits and CLGSCLK.WUPDIV[1:0]
is prohibited. When you set same wakeup clock source and division ratio as
before SLEEP mode, set CLGSCLK.WUPMD bit to 0
Feb/28/2014
errata_c17w15_2
S1C17 Family Technical Manual Errata
ITEM
POR Characteristics
Object manual
Document
Object item
Page
20.4 System Reset Controller (SRC)
20-4
code
S1C17W15 Technical Manual
412645701
Characteristics
(Error)
(Correct)
Jan/29/2014
errata_c17w15_1
S1C17 Family Technical Manual Errata
ITEM
Wakeup Clock Source
Object manual
Document code
Object item
Page
S1C17M01 Technical Manual
412361700
2.6 Control Register
2-13
S1C17F13 Technical Manual
412486300
2.6 Control Register
2-14
S1C17W15 Technical Manual
412645701
2.6 Control Register
2-18
(Error)
Bits 9–8
WUPSRC[1:0]
These bits select the SYSCLK clock source for resetting the CLGSCLK.CLKSRC[1:0] bits at wake-up.
When a currently stopped clock source is selected, it will automatically start oscillating or clock input
at wake-up. However, this setting is ineffective when the CLGSCLK.WUPMD bit = 0.
(Correct)
Bits 9–8
WUPSRC[1:0]
These bits select the SYSCLK clock source for resetting the CLGSCLK.CLKSRC[1:0] bits at wake-up.
When a currently stopped clock source is selected, it will automatically start oscillating or clock input
at wake-up. However, this setting is ineffective when the CLGSCLK.WUPMD bit = 0.
Notes： ・Do not select the clock source that has stopped. When selecting it, set the enable bit of the
clock source to 1 before the slp instruction.