1. No category

Hotel room control host
HDL-MHRCU.433
Parameters
Overview
Electric Parameters:
Working Voltage
DC20－30V
Static current
60mA/DC24V
Dynamic current
300mA/DC24V
Buspro connector
HDL Buspro, RJ45，INNER Buspro
RJ45 connection
UDP/IP network Interface
TRIAC
16A TRIAC, minimum load is 30w
Buspro terminal
0.75-0.85mm single-core cable
Environmental Conditions:
Working temperature
0℃~45℃
HDL-MHRCU.433 is the hotel room controller which is the core
Working relative humidity
Up to 90%
of the hotel system, it has mix controller, doorbell status dis-
Storage temperature
-20℃~+60℃
play, 24-channel dry contact and LED output. Hotel controller
Storage relative humidity
Up to 93%
has 48 channels. From the hotel management software, it can
Approved:
be programmed for parameters, control and monitor doorbell
CE
panel, curtain, lights, fan and A/C.
RoHS
Production Information:
Dimension
216×90×56（mm）
Weight
725g
Housing material
Nylon
Installation
35mm DIN rail installation
Protection degree
IP20
HDL Buspro Definition for Cable
Functions
The host control functions
■
It has 48 channels, each channel has parameters for
lower limit, the higher limit, the maximum limit.
■
Total is 99 scenes, each scene’s running time is 0250s.
■
Each channel has protection delay time (0-60mins).
Buspro
HDL Buspro/KNX cable
■
Each channel can delay turn ON time (0-250s).
COM
Black
■
Can run the scene according to the status of
DATA－
White
DATA+
Yellow
DC24V
Red
card
master.
■
Hotel host has RJ45 port for connection with another
room and reception or management center. With hotel
management software, this module can integrate with
Important Notes
third-party management software.
Mix control functions
■
Installation - Distribution box (DB )
■
Channel 1 to 13 is relay output ,each channel is 5A.
■
Buspro cable - CAT5E or HDL Buspro/KNX cable, 0.8mm single-
■
Channel 14 to 17 is relay output, each channel is 10A.
core copper cable.
■
Channel 18 to 21 is dimming output, each channel is
■
Buspro connection - Series connection (hand-in-hand).
■
RJ45 cable - CAT5E.
■
Make sure the IP address and IP MAC address are unique in IP
1A.
■
Channel 22 is relay of doorbell, it can control the doorbell status.
network.
Dry contract
■
Fuse must be aR type, and current should not exceed 10A.
■
■
When you replace the fuse, you should turn off
the power.
24-channel dry contract inputs.(The control target
should be set in the hotel management software.)
Door bell function
■
5-channel LED outputs. (it shows the doorbell status of
the third-party)
LED output function
■
Professional Home and Building Automation
www.hdlautomation.com
6-channel common switch indicator outputs.
Do you need help? Contact with us
[email protected]
1/ 2
www.hdlchina.com
酒店客房控制主机
HDL-MHRCU.433
Dimensions and Wiring
56
5CH LED indicators, it can connect with third56
party doorbell.
Universal switch for 1-5:
1. Wait, universal switch number is 19.
2. DND, universal switch number is 20.
3. Clean/laundry, universal switch number is 21.
90
4. Number, universal switch number is 22.
5. Bell, universal switch number is 23.
216
5CH LED indicators
Doorbell control
The resistor is between 1kΩ and 5k
Ω, it depends on the voltage of LED Lig
ht
6CH common switch LED
display
Indicator of fuse
24CH
dry contacts
Fuse socket
RJ45
Button and Indicator: Flickers
in green color when the module is working properly.
Keep pressing for 2s, you can
set the start channel.
Keep pressing for 10S, it will
turn red, the module will be
Default setting parameters：
reset to factory setting.
IP: 192.168.10.250
Router IP:192.168.10.1 Port: 6000
The network segment of the module should
be same as the PC.
Safety Attention
■
The screw down strength should not exceed 0.4 Nm.
■
Power cable: AC in: 2.5mm2 ~4mm2, load: 1.5mm2 ~2.5mm2.
■
Do not make wrong connection on Bus interface, it will damage the Bus interface of this module.
■
Do not get AC voltage into Bus wire , it will damage all devices in the system.
■
Ensure good ventilation.
■
Avoid contact with the liquids and aggressive gases.
Professional Home and Building Automation
www.hdlautomation.com
Do you need help? Contact with us
[email protected]
2/ 2