Download Report

Dataflex Telemetry for Remote
Tank Monitoring HYC-DF
Jr1113
DATAFLEX
WEB-ENABLED REMOTE MONITORING
HYCONTROL DATAFLEX
The Hycontrol DATAFLEX range of controllers provide easy, efficient and reliable data acquisition over a wide
range of level control applications. These units can be installed on a new or existing site to operate with any
Hycontrol level controller and can be configured either locally or remotely via a PC with the aid of DATAFLEX
software.
This system is suitable for numerous applications including remote level monitoring of liquids and solids in any tank,
vessel or silo and with the option for alarm relays to trigger external telemetry systems in remote areas.
APPLICATION FLEXIBILITY
• Remotely monitor virtually any instrumentation from any manufacturer
from any location.
• Monitors LEVEL, PRESSURE, FLOW, TEMPERATURE, PH,
CONDUCTIVITY
• Multiple users can access the same information and a choice of options
Allows different levels of security access.
ADVANTAGES OF DATAFLEX
Affordable and Flexible
Hycontrol’s Dataflex enables you to quickly and easily address a range of
remote monitoring and alarming applications using low cost hardware.
Four Configurable Inputs
The 4 inputs can work with a range of sensors, meters and other signals
giving a high degree of flexibility.
Integral Display
The integral back lit display means the device can be used to show the
readings locally, as well providing an easy way for the user to easily
configure and interrogate the unit.
Self Powered
Hycontrol’s Dataflex can operate from it’s own internal battery, even
providing power to the sensors, or you can connect an external power
source such as a solar cell.
Low Cost Operation
The quad-band GSM modem gives global operation and low cost GPRS
data transfer.
Low Installation Costs
It’s quick and easy to install and there’s no need for qualified electricians.
Data Logging
The unit can store 1,500 readings each with a time and data stamp
Expandable
The unit has an in-built expansion port - Different options are available
including a 5 channel pulse/digital board.
4 Configurable Inputs
USB-B port, Battery Powered
& Solar Powered
Quad-band GSM/GPRS modem
APPLICATIONS FOR ALL INDUSTRIES
QUARRY
WATER & WASTE
PROCESS
2
CHEMICAL
FOOD
3 WAYS TO POWER DATAFLEX SYSTEM
SOLAR POWER SYSTEM
· Connect up to 2 solar cells
· Intelligent regulation, maximising battery life
·
Temperature compensated
· Easy interface for sensors
· Option to monitor battery voltage on input 4
· Pulse charging to help recover from low battery voltages
· LED indication of status
· Simple battery replacement
MAINS POWER SYSTEM
· 110 to 230 Vac input
· Battery back
· Option to monitor supply voltage on input 4, therefore
Capable of providing 'mains fail' alarm
· Easy interface for sensors
·
Simple battery replacement
EXTERNALLY POWERED SYSTEM
· 6 to 24 Vdc input
· Battery back
· Option to monitor supply voltage on input 4
POWER REGULATOR BOARD FOR USE WITH A DATAFLEX
This circuit board provides flexibility allowing the Dataflex be easily connected to solar cells, external power sources and
mains power supplies (when used in conjunction with additional parts). It ensures efficient and intelligent battery charging,
helping you get the most out of your solar system.
Inputs:
2 x solar cells (max of 10 watt each)
12Vdc from external power source
(Not to be used in conjunction with solar cell)
Screw terminals for 4 input connections (for the Dataflex inputs)
Outputs: To 6 volt lead acid battery with intelligent charging capabilities
Power to the Dataflex (6 volts maintained (for Dataflex)).
3
· Connect either solar cells or external power
sources
· Maximise battery life and solar charging
potential
· Pre-charge conditioning if the battery is in
poor condition it helps to bring the battery
back to life
· Temperature compensation the charge rate
is adjusted according to the temperature of
the battery. This means the battery is always
charged at he toptimal rate, maximising the
battery life.
· Ability to monitor battery voltage on input4 of
the Dataflex switch selectable.
· LED indication (with test pushbutton) for
battery status and DC in.
SPECIFICATION DETAILS
General
Enclosure
Communications
Electrical
Analogue Input Channels
Antenna
Display
General
Expansion Card
Number of input channels
Connectors
Warranty
Environmental
Dimensions
Operating frequency
Output power
Power supply (N)
Excitation Supply (to sensors)
Input types
Resolution
Accuracy
40 x 40mm, 128 x 128pixels
Number of input channels
Connectors
Number of input channels
Input types
Maximum pulse frequency
x4
4 x 3 Pin 3.81mm pitch for sensors, 1 x 2 PIN for power
24 Months RTB. Does not cover above or incorrect installation
IP67 Rated
125 x 75 x 65 (mm)
850/900/1800/1900Mhz
Class 4 (2W) 850/900 Mhz
Class 1 (1W) 1800/1900 Mhz
Check
the type
of Dataflex
you have.
3.6, or 6 to 24 V DC @ 0.5A - Please ensure supply is clean.
smooth
. Check
the type
of Dataflex
you have.
3.6 v (unregulated), 5 v or 21.6 v. 31.25mA maximum
Digital or Analogue
10 bit (1024 Increments)
0.25%
is 0.25%
Internal or external (via SMA connector)
Backlit
x4
x4
4 x 3 Pin 3.81mm pitch for sensors, 1 x 2 PIN for power
x5
x5
Digital or Pulse
10Hz
VMI VENDOR MANAGED INVENTORY
Inventory monitoring on site or from remote locations offers many advantages for both suppliers and users of bulk
products. Ensuring that product arrives in a timely way is essential to modern JIT manufacturing. For the supplier of
the bulk products the emphasis is on the delivery logistics. For the user however it is imperative to maintain adequate
stock to satisfy production demand. When connected to Hycontrol level Instrumentation Dataflex provides reliable
inventory monitoring which can provide significant cost savings for both suppliers and customers alike. Typical
advantages of using Dataflex are :
• Improved response times for deliveries • Continuity of supply
• Improved vehicle and driver utilisation
• Improved delivery logistics
• Better delivery scheduling
• Reduction in product returns
• Better utilisation of company resources
• Reduced Wastage
POWER SUPPLIES AND CONSUMPTION
The choice of power source needs to suit your application. You can either use an internal lithium battery, an external
5 to 24 V DC power source, it could be solar, wind or a 110/230 V AC to 6-24V DC power supply. The supply needs to
be regulated and capable of delivering a peak of 0.5A.
The power consumption will vary depending on how the unit is programmed. If powering from the internal battery
then be sure to configure the ‘modem power scheme’ as ‘power off between transmit events.’
Please consult Hycontrol for advice on how long the battery will last in your application.
4
HYCONTROL LEVEL TECHNOLOGIES
(2)
(1)
(3)
Product Range For Solids :-
(4)
(5)
(1) TDR Radar For Solids
(2) Ultrasonic, ‘Through Air’
(2) 2 Wire Ultrasonic Transmitter
(6)
(3) FMCW 2 Wire Radar
(4) Continuous ‘Servo’ Level Indicator
(7)
(5) FMCW 2 Wire Radar
(8)
(6) Capacitance Level Switch
(9)
(9)
(7) Vibrating Probe Level Switch
(8) Rotating Paddle Level switch
(9) Microwave Level Switch
(10)
(10) Doppler Flow Switch
Product Range For Liquids :-
(4)
(1) By-Pass Level Indicator With Radar
(2)
(2) TDR Radar For Liquids
(3) 2 Wire Ultrasonic Transmitter
(3)
(5)
(6)
(7)
(1)
(4) FMCW ‘Horn’ Radar 2 Wire
(5) Magnetic Float Switches
(8)
(6) FMCW 2 Wire Radar
(9) (10)
(7) Foam Level Switch
(11)
(8) Capacitance Level Switch
(9) RF Admittance Level Switch
(11)
(10) Side Mounting 316 SS Float Switch
(11) Tuning Fork Level Switch
(11) Tuning Fork Level Switch
(12) Ultrasonics ‘Through Wall’
(13)
(12)
(13) Mini Magnetic Float Level Switch
Hycontrol Ltd, Larchwood House, Orchard Street, Redditch, Worcestershire, England, B98 7DP
Tel : 01527 406800, Fax : 01527 406810, [email protected], www.hycontrol.com