1. home and garden
2. home improvement and repair
3. roofing

The Leader in the Manucacture of Environmentally-safe
Roofing & Waterproofing Systems.
Hurricane Tested
Roofs • Walls • Decks • basements • wood
Brick & Masonry • Stucco • Underground Applications
Hydro-Stop LLC
1465 Pipefitter Street
Charleston, SC 29405
(800) 739-5566
(843) 745-9600
www.hydro-stop.com
United Coatings
19011 E. Cataldo Ave
Spokane Valley, WA 99016
(800) 541-4383
(509) 926-7143
www.unitedcoatings.com
We Can
Waterproof
Almost
Anything
United Coatings
6760 S. Clementine Ct.
Tempe, AZ 85283
(800) 835-9673
(480) 966-8999
www.unitedcoatings.com
Sustainability For The Life Of Your Building
900 Day
TERRA COTTA
• Metal roof waterproofing
and cooling
• Parapet wall waterproofing
• Low-sloped roof
waterproofing
• Flashing of all types
• Concrete waterproofing
• Plywood waterproofing
• Deck waterproofing
• Exterior wall waterproofing
• Sustainable roofing system that saves expensive
removal and disposal cost.
• Ultraviolet and Infrared resistant for added
durability.
• High Albedo reduces heat and lowers energy costs.
• Resistant to acid rain and chemical pollutants,
which protect roof or wall from fallout damage.
• Won’t spread flame over noncombustible surfaces.
• 100 % adhesion of system to substrate
• Wide range of colors provides beautiful
architectural finish.
• Meets V.O.C. emissions regulations to eliminate
facility downtime during application.
• Nontoxic formulation is safe to install.
• Easy application and cleanup.
• No special equipment required to install.
• 10-year extendable warranty available for roofs,
which means system never has to be torn off.
Factory Mutual approval recognition over insulation board, new built-up, existing built-up, metal,
and concrete. Please contact technical department for assistance with specifications.
®
PREMIUMCOAT SYSTEM
highest quality roofing and waterproofing systems available. It is made of the best raw
materials to form a flexible, U.V. resistant elastomeric compound and is fully reinforced
with a tough nonwoven polyester fabric which has been designed for roofing and flashing
applications of all types. PREMIUMCOAT® is easy to apply, safe to work with and requires no
special equipment.When the system is properly installed, by a certified applicator, a 10 year
warranty is available for specific roofing applications. The warranty can then be extended
every 10 years under a proper maintenance schedule.
ADVANTAGES & BENEFITS
TECHNICAL DATA
Product
Shelf life and storage conditions
Roof Temperature, Black Asphalt
1600
DESERT SAND
WHITE
Reinforced Acrylic Elastomeric System
18 months if unopened and stored
between 40°F (4°C) & 90°F (32°C)
Density
12.1 lb/gal
Application temperature
min = 40°F (4°C) to 105°F (41°C) (Ambient)
min =36°F (2°C) to 130°F (51°C) (Surface)
Drying time (Touch Dry)
1-4 hours at 77°F (25°C) / 40% humidity
Full cure
7 days
Total thickness
40-45 mils
Peak Tensile strength of system (ASTM D-412)
2210 psi (15.24mPa)
Elongation: of cured system
> 53%
Water vapor permeability: (ASTM D-1653)
(ASTM D-6083) 3-5 perms
Fungus resistance: (ASTM-G21)
No growth supported
Algae resistance: (ASTM G-29)
No growth supported
Flammability: (ASTM E-108)
Class A over noncombustible deck
Salt spray test: (ASTM B-117)
No effects noted
Percent solids
66.9%
Low temperature flexibility (ASTM D-522)
180° flexibility; bend at -15°
Substrates
Uplift Pressure Resistance
Wind uplift
Concrete
6,098 psf (292kPa)
Protocol (PA 114)
Uplift pressure resistance
Polyisocyanurate
1,189 psf (56.9kPa)
Smooth surface BUR
2,261 psf (108.3kPa)
Granule surface Cap sheet
1,753 psf (83.9kPa)
Accelerated weathering (ASTM G-26)
Meets PA 129
protocol for 3,600 hours.
High Albedo
Cool Reflective
Less Than
1000
BROWN
CHARLESTON GREEN
BATTLESHIP GREY
DOVE GREY
PATINA GREEN
CHARCOAL
PREMIUMCOAT® SYSTEM
PREMIUMCOAT ® sustainable roofing and waterproofing system is one of the
USES
TINNERS RED
3
2
Colors represented are approximate. Please consult your technical representative for specific color samples.
PREMIUMCOAT SYSTEM
METAL ROOFS
®
Metal roofs exhibit most of their leaking problems at laps, seams, skylights, fasteners and other penetrations.
The PREMIUMCOAT® system is used extensively to repair and waterproof commercial, industrial, and historic standing-seam metal roofs.
The PREMIUMCOAT® system bonds with any metal surface, providing a permanent watertight solution to any metal roof leakage problem.
PREMIUMCOAT® system installed for waterproofing and cooling of metal roof and newly installed skylights at moving and storage facility in Hawaii.
PREMIUMCOAT® being installed at paper company to reduce roof temperature and waterproof in Mississippi.
During
After
Factory Mutual approval recognition
over insulation board, new built-up,
existing built-up, metal, and concrete.
Please contact technical department for
assistance with specifications.
STABLERUST primer installed over rust and PREMIUMCOAT® system being installed over laps, seams and fasteners to waterproof
commercial metal roof in Alabama.
Above: Waterproofing of a commercial metal roof.
Completed PREMIUMCOAT® system in Tinners Red at Air Force base in Alabama.
Removal of shingles from old standing-seam metal roof.
4
Above: PREMIUMCOAT® waterproofing and cooling industrial roof at major chemical plant.
PREMIUMCOAT® waterproofing system installed over fiberglass skylight on metal roof.
Application of FOUNDATIONCOAT and fabric to roof.
Above: Before, during and after preparation and waterproofing of historic standing-seam metal roof.
Historic standing-seam metal roof finished in Tinners Red.
5
Before
During
•
•
2
1
PREMIUMCOAT® system installed over existing built-up roofing at school in Georgia.
PREMIUMCOAT® FOUNDATIONCOAT system being installed.
®
PREMIUMCOAT SYSTEM
The greatest enemy for a built up roof is the sun. The sun’s powerful infrared and ultraviolet rays cause heat aging of the built-up system
resulting in the leaching of oils, causing the roof to prematurely dry out and crack. The PREMIUMCOAT® system is used on both new
and existing built-up and modified roofs providing a protective barrier between the substrate and the sun’s damaging rays.
Built-up roof, before PREMIUMCOAT® system.
Installation of PREMIUMCOAT® FOUNDATIONCOAT over existing built-up.
•
•
After
4
3
After: Completed PREMIUMCOAT® system installed over existing built-up roof at school system in Georgia.
Application o f FOUNDATIONCOAT and fabric over expansion joint and roof deck.
Roof and skylights waterproofed with FOUNDATIONCOAT and awaiting application of finish coat.
Above: PREMIUMCOAT® system installed over modified Bitimun for cooling and
prevention of ultraviolet breakdown in Miami, Florida.
PREMIUMCOAT® SYSTEM
BUILT-UP / MODIFIED BUILT-UP ROOFING
Completed PREMIUMCOAT® system installed over built-up roofing at Marine Base in North Carolina.
6
Above: PREMIUMCOAT® system being installed as a cap sheet over a new built-up roof to provide protection from
the sun and heat aging at military base in Alabama.
Above: New built-up roofs with PREMIUMCOAT® as a protective cap sheet built-up roof.
7
DECKS
PLYWOOD AND
INSULATION BOARD
PREMIUMCOAT® is a high-performance, sustainable system for plywood and insulation board. Its superior adhesion characteristics and its inherent ultraviolet and
infrared resistance make it ideally suited for the harshest environments.
During
Decks are most often roofs that you walk on. The PREMIUMCOAT® system is ideal for waterproofing decks because of its ability to flash from deck to
wall junctions, railings and post. The system is renewable by recoating every five years and if it is damaged it can easily be repaired. TRAFFICCOAT
abrasion resistant coating can be applied over the system to provide a tough, easy-to-clean surface.
After
Above & below: PREMIUMCOAT® system being installed over roof deck, parapet walls and transitions at lumber company.
APPLICATION GUIDELINES
Above: PREMIUMCOAT® system and TRAFFICCOAT providing a waterproof traffic surface at beach house.
Surface Preparation
Power wash and clean all surfaces to be waterproofed.
Priming
Chalking surfaces should be primed with SureBond Primer.
Rusty surfaces should be primed with StableRust Primer.
Concrete surfaces should be primed with BarrierGuard®.
Black EPDM surfaces should be primed with CleanAct Primer.
All other surfaces do not require priming..
Application
Install cant strips at all internal corners.
Apply a 6” or 12” wide strip of PremiumCoat® FoundationCoat, Fabric, and
FoundationCoat over cant strips, cracks and joints such as plywood and insulation
board.
Apply the FoundationCoat, Fabric and FoundationCoat all in one step to the area
to be waterproofed making sure there are no wrinkles or air pockets. Overlap fabric
by 4 inches.
Apply the FinishCoat to the treated area in two coats.
Coverage
FoundationCoat = 200 square feet per 5 gal.
Fabric 40”= 1000 square feet
Finish Coat = 350 square feet per 5 gal. (Includes 2 coats)
CONCRETE ROOFS
above. Installation over plywood roof and decks at Dewees Island Nature Preserve (PREMIUMCOAT® selected
for its environmentally friendly formulation, sustainability and hurricane-proof uplift resistance).
Questions? Call Hydro-Stop, Inc. or your Hydro-Stop Representative.
During
8
Installation of PREMIUMCOAT® FOUNDATIONCOAT system over polysaturate insulation board at military base housing in Guam.
The largest concern with waterproofing structural concrete is finding a system which will remain permanently bonded even in hurricane conditions.
PREMIUMCOAT® is a fluid applied, fully adhered, breathable system. It is excellent for waterproofing structural concrete, and its bonding ability to both substrates
is many times greater than even the most stringent roofing standards. PREMIUMCOAT® forms a monolithic system which will mold to any type of surface and is
therefore an excellent means of extending the waterproofing membrane onto any curb, penetration, or parapet wall.
After
Completed PREMIUMCOAT® system installed over insulation board military base housing in Guam.
Installation of PREMIUMCOAT® system over structural concrete roof at family housing project in Puerto Rico.
Above: PREMIUMCOAT® system installed over concrete on
hotel roof deck in South Beach, Miami, Florida.
9
retaining walls and moisture-retaining structures such as gutters, cisterns, and concrete shrubbery boxes. Mixed with water and
Portland cement, and fully reinforced with BARRIERGUARD® fabric, it forms a hard-wearing, flexible compound. It is also resistant to
standing water and ideal for subterranean waterproofing.
Surface Preparation
Remove any loose or flaking particles, scale, dirt, rust or scale. Masonry
surfaces need to be dampened first to prevent moisture loss from slurry.
USES
TECHNICAL DATA
• Abrasion-resistant layer for decks
and walkways
• Waterproofing foundation walls
• Waterproofing basements
• Lining water-retaining structures
• Waterproofing shrubbery boxes
• Waterproofing shower floors
Storage conditions................................................................................40°F (4°C) to 95°F (35°C)
Shelf life....................................................................................12 months in unopened containers
Potlife.................................................................................................20-30 minutes @ 77°F (25°C)
Membrane thickness .................................................................................................................60 mils
Bond strength.......................................................................................................> 550 psi (3.8 mPa)
Tensile strength ASTM C-109-85........................................................................330 psi (2.3 mPa)
Comprehensive strength ASTM C-109-88..................................................5,690 psi (39.2 mPa)
Flexual Strength ASTM 3348-86.....................................................................1835 psi (12.7 mPa)
Packaging..................................................................................1 gallon (3.79 L) & 5 gallon (18.9 L)
®
BARRIERGUARD SYSTEM
APPLICATION GUIDELINES
ADVANTAGES & BENEFITS
•
•
•
•
•
•
•
•
•
•
•
Mixing
Slurry is prepared by mixing (one-part BarrierGuard®, one-part water,
and three parts Portland cement). Add BarrierGuard® and water to a clean
5- gallon pail and mix with a slow-speed mechanical mixer for about 1
minute. Slowly add the Portland cement until a totally homogenous and
lump-free slurry is produced. Above 80 degrees it is recommended to
add ice to cool down the slurry mix to prevent premature gelling.
Application
Apply BarrierGuard® slurry to the dampened area and immediately
imbed the BarrierGuard® Fabric in the wet slurry. Work out any bubbles
or creases with the brush. Fully saturate the Fabric from above with
more slurry and allow to dry. Follow with a final coat of BarrierGuard®
slurry. BarrierGuard® Fabric should lap by minimum of four inches.
Coverage
One gallon of BarrierGuard® will make approximately four gallons
of slurry. The slurry will cover approximately 50 square feet of full
BarrierGuard® System that is reinforced with fabric, or 250 square
feet of single coat priming.
BarrierGuard® being installed on exterior of basement wall prior to back fill at private residence in North Carolina.
Questions? Call Hydro-Stop, Inc. or your Hydro-Stop Representative.
Protects masonry surfaces from water damage
Will not peel off like stick-on adhesives
Wear-resistant and hard to damage
Resists ponding water
Extremely U.V. resistant
Resists acid rain and chemical pollutants to
protect from chemical spills and fallout damage
Meets V.O.C. emissions and regulations to
eliminate facility downtime during installation
Nontoxic formulation is safe to apply
Easy application and cleanup
No special training or equipment required to install
5-year extendable warranty means system never has
to be torn off
Before
After
BarrierGuard® system installed on CBU foundation, prior to installation of landscaping berm in Sea Island, Georgia.
Before: BarrierGuard® system installed inside large concrete planters prior to installation of palm trees.
BARRIERGUARD® SYSTEM
BARRIERGUARD ® is designed for waterproofing all types of masonry surfaces such as foundation walls, concrete panels,
NSF
®
Application of
10
BarrierGuard® system to CMU foundation.
Above: Sealing concrete shrubbery box.
11
FLEXCOAT
CLEARGUARD PLUS ® provides a durable, clear protective barrier against oil, water, oil-based dirt, and water-based dirt. Utilizing state
of the art technology, this coating is effective for unpainted masonry. CLEARGUARD PLUS® is easy to apply and doesn’t require
specialized equipment. Being solvent free, CLEARGUARD PLUS® is safe to work with, and does not emit harmful fumes or odor.
CrackBridging Elastomeric
Coating
Masonry, and in particular, stucco, is a major point
of entry for water. This is especially true since
masonry tends to crack. FLEXCOAT crackbridging
elastomeric is carefully formulated to stay flexible
to handle crack movement and provide a highquality water seal at the same time. FLEXCOAT keeps
the water out while allowing you the option of
hundreds of colors to match your decor.
ADVANTAGES & BENEFITS
• Lower surface tension of substrate to repel water, oil, water-based dirt
and oil-based dirt
• Bonds to a wide variety of substrates and can easily be used on all types
of masonry and gypsum
• Eliminates or reduces effluorescence
• Exceeds NCHRP 244 requirements
• Meets SS-W-11OC Federal specifications
• Meets V.O.C. emissions regulations making it safe to use and eliminates
facility downtime during application
• Nontoxic formulation is safe to install
• Easy application and cleanup lowering job costs
USES
• Water and oil repellent for Mortar,
Brick, Stucco, Split-Faced Concrete
Block, Concrete, Concrete
Block, Limestone, Marble, Slate,
Tile, Sandstone, Granite, Clay
Brick and Terra Cotta
• Oil-based dirt and water-based
dirt repellent on vertical and
horizontal surfaces
APPLICATION GUIDELINES
Above: Waterproofing over structural concrete.
Surface Preparation
Remove debris, dirt, oil and other latience from substrate by powerwashing and
mechanical scraping. Repair any damaged mortar and fill all cracks with appropriate
filling material. (Contact Hydro-Stop technical department with technical questions.)
Coverage
Coverage may vary between 80-400 square feet per gallon depending on porosity
of the substrate.
Questions? Call Hydro-Stop, Inc. or your Hydro-Stop Representative.
Application
Stir ClearGuard Plus® well before use. Apply by brush or low-pressure (pump-up)
sprayer. Apply in wet-on-wet fashion allowing product to run down surface
approximately 12 inches. Curing time: 72 hours.
Above: Damaged stucco which has been repaired with FLEXCOAT
Concrete repair and waterproofing of church. BarrierGuard® and PREMIUMCOAT® also used to protect building envelope.
APPLICATION GUIDELINES
Surface Preparation
Power wash and clean all surfaces to be waterproofed.
CLEARGUARD PLUS® being applied to structural concrete office building.
Untreated
CLEARGUARD PLUS® being applied to exterior brick wall at University of North Carolina at Wilmington.
Treated
Priming
Chalking surfaces must be primed with SUREBOND PRIMER.
All other surfaces do not require priming.
Application
Apply FLEXCOAT by brush, roller or sprayer at a rate of 180 square feet per gallon.
Allow 8 hours to dry before applying a second coat.
At least two coats must be applied.
Coverage
SUREBOND PRIMER = 300 square feet per gallon.
FLEXCOAT = 1 coat... 180 square feet per gallon.
2 coats... 90 square feet per gallon.
3 coats... 60 square feet per gallon.
Questions? Call Hydro-Stop, Inc. or your Hydro-Stop Representative.
12
Waterproofing of synthetic stucco on bank building in South Carolina.
Above: Treated and untreated split-faced block. Notice water-soaked untreated area.
Example of water absorbing into split-face concrete block leading to wall problems.
CLEARGUARD PLUS®
FLEXCOAT