Download Report

Slide Compound
Mitre Saw
1600W
Instruction Manual
3 Year Replacement Warranty
OZSCMS1600WA
CAUTION: Read this operation manual before using this tool.
0212
To view the full range visit:
www.ozito.com.au
SPECIFICATIONS – MODEL NO. OZSCMS1600WA
Motor size:
Input:
No load speed:
Net weight:
Mitre angles:
Bevel angles:
Cutting capacity::
1600W S1; 2000W S6.25% 2.5min load, 7.5min no load
230-240V ~ 50Hz
5,000/min
18kg
0º - 45º left and right
0º - 45º left
0º x 90º: 305 x 78mm
45º x 90º: 210 x 78mm
0º x 45º: 305 x 42mm
45º x 45º: 210mm x 42mm
254mm
30mm
Saw Blade diameter:
Arbour size:
Know yourYOUR
ProductPRODUCT
KNOW
1
3
26
25
1
2
23
24
27
22
28
3
30
21
4
20
5
19
6
29
18
7
17
8
16
15
12
14
13
11
10
9
31
33
32
2
1.
2.
3.
4.
5.
6.
7.
8.
9.
Carry handle
Switch handle
On/off switch
Lower guard
Blade bolt cover
Blade
Mitre table lock
Table insert
Mitre table handle
10.
11.
12.
13.
14.
15.
16.
17.
18.
Table leg
Mitre angle indicator
Mitre scale
Mounting hole
Mitre table
Base
Extension bar
Locking screw
Fence
19.
20.
21.
22.
23.
24.
25.
26.
27.
Material clamp
Bevel scale
Trenching stop
Slide rail
Dust bag
Guard arm
Upper guard
Lock down knob
Slide lock
28
28. Bevel lock
29. Spindle lock
30. Guard release lever
(European version only)
31. 0° Bevel adjust screw
32. Stabilising bar
33. 45° Bevel adjust screw
TABLE OF CONTENTS
SPECIFICATIONS…….…………………………………… Page 2
KNOW YOUR PRODUCT………………………………… Page 2
INTRODUCTION…………………………………………. Page 4
SAFETY INSTRUCTIONS………………………………... Page 4-6
ADDITIONAL SAFETY RULES…………………………...Page 7-8
OPERATION ……………………………………………… Page 9-16
MAINTENANCE …………….…………………………… Page 16
DESCRIPTION OF SYMBOLS…………………………... Page 17
CARING FOR THE ENVIRONMENT…………………... Page 18
CONTENTS ……………………………………………….Page 18
WARRANTY……………………………………………….. Page 19
3
INTRODUCTION
Congratulations on purchasing an Ozito Slide
Compound Mitre Saw. We aim to provide quality tools
at an affordable price. We hope you will enjoy using
this tool for many years.
The Ozito Slide Compound Mitre Saw OZSCMS1600WA
has been designed for the easy cutting of timber and
timber products. It is intended for DIY use only.
SAFETY INSTRUCTIONS
!
Warning! When using mains-powered tools, basic safety precautions,
including the following, should always be followed to reduce risk of fire,
electric shock, personal injury and material damage.
Read the whole manual carefully and make sure you know how to switch the
tool off, in an emergency, before operating the tool.
Save these instructions and other documents supplied with this tool for
future reference.
ELECTRICAL SAFETY
The electric motor has been designed for 230V and 240V only. Always check that
the power supply corresponds to the voltage on the rating plate.
Note: The supply of 230V and 240V on Ozito tools are interchangeable for
Australia and New Zealand.
This tool is double insulated in accordance with AS/NZS 3100; therefore no
earth wire is required. If the supply cord is damaged, it must be replaced by an
electrician or a power tool repairer in order to avoid a hazard.
Using an Extension Lead
Always use an approved extension lead suitable for the power input of this tool.
Before use, inspect the extension lead for signs of damage, wear and ageing.
Replace the extension lead if damaged or defective.
When using an extension lead on a reel, always unwind the lead completely. Use of
an extension lead not suitable for the power input of the tool or which is damaged
or defective may result in a risk of fire and electric shock.
4
It is recommended that the extension lead is a maximum of 25m in length. Do Not
use multiple extension leads.
GENERAL SAFETY RULES
!
Warning! Read all instructions. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury. The term “Power Tool”
in all of the warnings listed below refers to your mains operated (corded)
power tool or battery operated (cordless) power tool.
SAVE THESE INSTRUCTIONS
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
1) WORK AREA
a) Keep work area clean and well lit. Cluttered and dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases, or dust. Power tools create sparks which
may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions
can cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging
the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.
e) Replacement of the supply cord. If the supply cord is damaged, it must be
replaced by an electrician or a power tool repairer.
f)
When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
g) Have your tool repaired by a an electrician or a power tool repairer.
This power tool complies with relevant safety requirements. To avoid danger,
electrical appliances must only be repaired by qualified personnel using original
spare parts; otherwise this may result in considerable danger to the user.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention while operating power
tools may result in serious personal injury.
5
GENERAL SAFETY RULES (cont.)
b) Use safety equipment. Always wear eye protection. Safety equipment such
as dust mask, non-skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Avoid accidental starting. Ensure the switch is in the off position before
plugging in. Carrying power tools with your finger on the switch or plugging in
power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result
in personal injury.
e) Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected situations.
f)
Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of these
devices can reduce dust related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the rate
for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off.
Any power tool that can not be controlled with the switch is dangerous and
must be repaired.
c) Disconnect the plug from the power source before making any
adjustments, changing accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools, unplugged & out of the reach of children and do not
allow persons unfamiliar with the power tool or these instructions to operate
the power tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tools
operation. If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.
f)
Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in accordance with
these instructions and in the manner intended for the particular type of
power tool, taking into account the working conditions and the work to
be performed. Use of the power tool for operations different from intended
could result in a hazardous situation.
5) SERVICE
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power tool
is maintained.
6
ADDITIONAL SAFETY RULES FOR MITRE SAWS
This appliance is not intended for use by young or infirm persons unless supervised
by a responsible person to ensure that they can use the appliance safely.
Young children should be supervised to ensure that they do not play with
the appliance.
!
Warning! Before connecting a tool to a power source (mains switch power
point receptacle, outlet, etc.) be sure that the voltage supply is the same as
that specified on the nameplate of the tool. A power source with a voltage
greater than that specified for the tool can result in serious injury to the user,
as well as damage to the tool. If in doubt, do not plug in the tool.
Using a power source with a voltage less than the nameplate rating is harmful to the motor.
Your tool is double insulated for additional protection against a possible electrical
insulation failure within the tool.
Always remove the plug from the mains socket before making any adjustments or
maintenance, including changing the blade.
•
When operating the saw, use safety equipment including safety goggles or shield,
ear protection, dust mask and protective clothing including safety gloves.
•
Ensure that there is adequate general or localised lighting.
•
Do not use the saw unless the guards are in place.
•
Do not use the saw to cut metal or masonry.
•
Do not let anyone under 18 years operate this saw.
•
Ensure that the operator is adequately trained in the use, adjustment and
operation of the machine.
•
Do not use this saw to cut firewood.
•
Keep the area free of tripping hazards.
•
Report faults in the machine, including guards and saw blades, as soon as they
are discovered.
•
Ensure that the machine is always fixed to a bench, whenever possible.
•
Always stand to one side when operating the saw.
•
Never use a cracked or distorted saw blade.
•
When cutting round wood, use clamps that prevent the workpiece from turning on
both sides of the blade.
•
Never use your hands to remove sawdust, chips or waste close by the blade.
•
Use only blades as recommended by the manufacturer and which conform to EN 847-1.
•
Do not use blades of High Speed Steel (HSS blades).
•
If the table insert is damaged or worn, have it replaced by a power tool repairer.
•
Rags, cloths, cord and string and the like should never be left around the work area.
•
Avoid cutting nails. Inspect the workpiece and remove all nails and other foreign
objects before operating the saw.
•
Support the work properly.
•
Refrain from removing any cut-offs or other parts of the workpiece from the cutting
area whilst the machine is running and the saw head is not in the rest position.
•
Do not attempt to free a jammed blade before first switching off the machine.
7
ADDITIONAL SAFETY RULES FOR MITRE SAWS (cont.)
•
Do not slow or stop a blade with a piece of wood. Let the blade come to
rest without assistance.
•
If you are interrupted when operating the saw, complete the process and
switch off before looking up.
•
Periodically check that all nuts, bolts and other fixings are properly tightened.
•
Do not store materials or equipment above a machine in such a way that they
could fall into it.
•
Always hold the saw on parts that are insulated. If you accidentally cut into
hidden wiring or the saw’s own cable, the metal parts of the saw will become
“live”. Switch off at the mains and remove the plug immediately.
•
Never saw near combustible liquids or gases.
•
Note the direction of rotation of the motor and the blade.
•
Do not lock the movable guard in the open position and always ensure that it is
working properly, freely rotating and returning to fully cover the teeth of the blade.
•
Connect the saw to a dust collection device and ensure that it is operating
properly. As the operator of the saw, please make sure that you understand
factors that influence exposure to dust, including the type of material to be cut,
the importance of local extraction and the proper adjustment of
hoods/baffles/chutes of your dust extraction system. We recommend that you
always wear a dust mask when operating this saw.
•
Wear gloves when handling saw blades and rough materials.
•
Saw blades shall be carried in a holder wherever possible.
•
Select saw blades in relation to the material being cut.
•
Use correctly sharpened saw blades and observe the maximum speed marked
on the blade.
•
Take additional care when trenching (slotting).
•
The mitre saw can be safely carried by the carrying handle but only once it has
been removed from the mains power and secured in the locked down position.
•
Ensure that the arm is properly secure when bevelling.
•
Keep the floor area around the machine level, well maintained and free of
loose materials.
•
Ensure that you are trained in the use, adjustment and operation of the machine.
•
Do not remove any cut-offs from the cutting area until the mitre saw head is in
the full upright position, the blade guard is fully enclosing the blade and the
blade has come to a rest or complete stop.
•
When cutting long pieces which extend well over the table width, ensure that
the ends are adequately supported at the same height as the saw table top.
Supports should be positioned in such a way to ensure that the workpiece does
not fall to the ground once the cut has been made.
A number of supports at regular intervals may be required if the workpiece is
extremely long.
8
-
Wear goggles
-
Wear earmuffs
-
Wear a breathing mask
TOOL OPERATION
Transportation
Only lift the saw when the head of the mitre saw is locked in the down position, the
saw is turned off and the plug is removed from the power point.
To lock the mitre saw head in the down position push the mitre saw head down
towards the base and engage the lock down knob (26). This will ensure that the mitre
saw head is locked in the down position and enable you to lift the mitre saw by the
carry handle (1) safely.
Only lift the saw by the carrying handle (1) or outer castings. Do not lift the saw using
the upper guard (25) or switch handle (2).
Bench mounting
The saw has mounting holes (13) in each corner to facilitate bench mounting.
1. Mount the saw to a level, horizontal bench or work table using 4 bolts (not
supplied) and ensure that the saw is fastened tightly.
2. If desired, you can mount the saw to a piece of 13mm or thicker plywood which can
then be clamped to your work support or moved to other job sites and re-clamped.
!
CAUTION: Make sure that the mounting surface is not warped as an uneven
surface can cause binding and inaccurate sawing.
Lock down knob
The lock down knob (26) is provided for holding the cutting head down whilst
transporting or storing the mitre saw. The saw must never be used with the lock down
knob (26) locking the head down.
Slide lock
When tightened, the slide lock (27) prevents the saw head from sliding. Tighten the
slide lock (27) during transportation.
Mitre table lock
The mitre table lock (7) is used to lock the mitre table (14) at the desired mitre angle.
The mitre saw cuts from 0° to 45° both left and right. To adjust the mitre angle, loosen
the mitre table lock (7) and using the mitre table handle (9) adjust the mitre angle to
the desired position. The mitre table features positive click stops at 0°, 15°, 22.5°, 30°
and 45° for quick setting of common mitre angles.
!
Warning! Be sure to tighten the mitre table lock (7) before making a cut.
Failure to do so could result in the table moving during the cut and cause
serious personal injury.
Bevel lock
The bevel lock (28) is used to set the blade at the desired bevel angle. The mitre saw
bevel cuts from 0° to 45° to the left.
Note: The bevel lock lever (28) is spring loaded to allow repositioning of the handle
for maximum leverage in confined spaces. By pulling out the lever and at the same
time rotate to the opposite direction, then releasing will allow you to position the
handle again to turn in the desired direction for your continued tightening or
loosening application.
9
TOOL OPERATION (cont.)
To adjust the bevel angle loosen the bevel lock (28) and tilt the mitre saw head
towards the left. This will enable the mitre saw blade (6) to be tilted to your
desired bevel angle.
!
Warning! Be sure to tighten the bevel lock (28) before making a cut.
Failure to do so could result in the saw arm moving during the cut and
cause serious personal injury.
Clamp assembly
The material clamp (19) can be mounted to the fence (18), on either the Right or
Left of the fence. This will assist when making cuts when feeding materials from
either side of the saw.
When performing a bevel cut, the material clamp (19) should be positioned on the
right hand side of the fence (18).
Secure the material clamp (19) by tightening the bolt at the back of the fence (18).
Spindle lock
The spindle lock (29) prevents the blade in the saw from rotating. Depress and
hold the spindle lock (29) while installing, changing, or removing the blade (6).
Lower guard
The lower guard (4) provides protection to your hands and limbs when the mitre
saw head is in the up position or during the operation of the saw when the saw is
turned on and you are making a cut. It retracts over the upper guard (25) as the
saw is lowered into the work piece.
Dust bag
The dust bag (23) fits over the dust extraction port behind the carry handle (1).
For more efficient operation, empty the dust bag (23) when it is no more than half
full. This allows better air flow through the bag.
Note: Dust bags will not collect all the saw dust generated by the mitre saw. For
best results a dust extractor should be used in place of the dust bag.
Attaching the extension bars
The extension bars (16) help to support the material when working with long
workpieces.
Prior to inserting the extension bars (16) loosen the phillips locking screws (17) that
are located on either side of the mitre table (14) side wings.
The extension bars (16) fits on either side of the base (15) by inserting the two
ends of the extension bars (16) into the two holes in the end of the base (15).
Ensure the extension bars (16) are fully inserted before using them to support the
workpiece.
The locking screw (17) must be tightened to secure the extension bars (16) in position.
Attaching the stabilising bar
The stabilising bar (32) is fitted to the rear of the saw below the bevel lock (28) to
stabilise the saw during normal operation.
10
TOOL OPERATION (cont.)
Trench depth adjustment (see Fig 1).
In its normal position, the trenching stop plate (C)
permits the saw blade to cut right through a
workpiece. When the guard arm (24) is lifted, the
trenching stop plate (C) can be moved to the left so
that the trenching depth adjustment screw (A)
contacts the trenching stop plate (C) as the guard arm
(24) is lowered. This restricts the cut to a “trench” in
the workpiece. The depth of the trench can be
adjusted with the trenching depth adjustment screw
(A) and locked in position with the trenching depth
lock nut (B).
!
A
B
D
C
Fig. 1
Warning! Do not adjust screw assembly (D). This adjustment ensures that the
saw blade will not cut into the base of the tool and the bench top on which
the tool is positioned on. The screw assembly (D) is factory set and should
not be adjusted by the operator. Failure to observe this could cause damage
to the tool and/or injury to the operator.
Switching the tool on
To turn the saw on, depress and hold the on/off switch (3). To turn the saw off, release
the on/off switch (3).
Setting the table square with the blade
Make sure that the electrical plug is removed from the power point.
Push the switch handle (2) down to its lowest position and engage the lock down knob (26)
to hold the saw in the transport position.
Loosen the mitre table lock (7).
Rotate the mitre table (14) until the mitre angle indicator (11) is positioned at 0º.
Tighten the mitre table lock (7).
Loosen the bevel lock (28) and set at 0º bevel (the blade at 90º to the mitre table).
Tighten the bevel lock (28). Place a set square against the mitre table (14) and the flat
face of the mitre saw blade (6).
Note: Make sure that the square contacts the flat face of the mitre saw blade (6), not
the teeth.
Rotate the blade (6) by hand and check the blade-to-table alignment at several points.
The edge of the set square and the saw blade (6) should be parallel. If the saw blade (6)
angles away from the set square, adjust as follows.
Use an allen key to loosen the bevel adjust screw (31). Also, loosen the bevel lock (28).
Adjust the bevel adjust screw (31) to 0° with the allen key to bring the saw blade into
alignment with the square.
Loosen the Phillips head screw holding the pointer of the bevel scale (20) and adjust the
position of the pointer so that it accurately indicates zero on the scale and retighten the
screw. Retighten the bevel lock (28) and the bevel adjust screw (31).
11
TOOL OPERATION (cont.)
Note: The above procedure can also be used to check the angle of the saw blade
to the table at 45º bevel angle. The 45° bevel adjustment screw (33) is on the
opposite side of the saw arm.
Setting the fence square with the table
Make sure that the electrical plug is removed from the power point.
Push the switch handle (2) down to its lowest position and engage the lock down
knob (26) to hold the saw arm in the transport position.
Loosen the mitre table lock (7) and rotate the mitre table (14) until the mitre angle
indicator is positioned at 0º.
Tighten the mitre table lock (7). Loosen the four screws securing the fence (18) to
the base (15).
Place a square against the fence (18) and alongside the blade face (6). Adjust the
fence (18) until it is square with the blade face (6).
Tighten the screws securing the fence (18). Loosen the Phillips head screw holding
the mitre scale indicator (11) and adjust it so that it accurately indicates the zero
position on the mitre scale (12).
Retighten the screw securing the mitre scale indicator (11).
Changing a blade
Make sure that the electrical plug is removed from the power point.
!
Danger! Never try to use a blade larger than the stated capacity of the
saw. It might come into contact with the blade guards. Never use a blade
that is too thick to allow the outer blade washer to engage with the
spindle. It will prevent the blade screw from properly securing the blade
on the spindle. Do not use the saw to cut metal or masonry. Ensure that
any spacers and spindle bushes that may be required, suit the spindle
and the blade fitted.
Raise the mitre saw head to its highest position. Using a Phillips head screwdriver
loosen and remove the screw that secures the guard arm (24) to the lower guard (4).
Using a Phillips head screwdriver loosen and remove the screw that secures the
blade bolt cover (5).
Pull the lower guard (4) down then swing it up together with the blade bolt cover
(5). When the lower guard (4) is positioned over the upper guard (25), it is now
possible to access the blade bolt. Hold the lower guard (4) up and press the
spindle lock (29). Rotate the mitre saw blade until the spindle locks into position
and the blade is unable to turn. Use the allen key to loosen and remove the blade
bolt. (Loosen in a clockwise direction as the blade screw has a left hand thread).
Remove the flat washer, outer blade washer and the the mitre saw blade (6).
12
TOOL OPERATION (cont.)
Wipe a drop of oil onto the inner blade washer and the outer blade washer where
they contact the blade. Fit the new blade onto the spindle taking care that the inner
blade washer sits behind the blade.
!
CAUTION: To ensure correct blade rotation, ensure that the arrow direction
of blade is the same as the arrow on the upper guard (25).
Replace the outer blade washer. Fit a replacement mitre saw blade (6). Depress the
spindle lock (29) and replace the flat washer and blade bolt. Use the hex key to
tighten the blade bolt securely (tighten in an anticlockwise direction).
Lower the upper guard (25), hold the lower guard (4) and blade bolt cover (5) in
position and tighten the fixing screw. Position the guard arm (24) in place and secure
onto the lower guard (4).
Check that the blade guard (4) operates correctly and covers the blade as the saw arm
(24) is lowered.
Connect the saw to the power supply and depress the on/off switch (3) to start the
saw to make certain that the blade is installed correctly and does not make contact
with any part of the safety guards (4 and 25)..
Cross-cutting (without slide action)
When cutting a narrow piece of wood it is not necessary to use the slide mechanism.
In this case ensure that the slide lock (27) is screwed down to prevent the saw arm
from sliding. A crosscut is made by cutting across the grain of the work piece.
A 90º crosscut is made with
the mitre table (14) set at 0º.
Mitre crosscuts are made with
the mitre table (14) set at an
angle other than zero.
To make a cut release the lock
down knob (26) and raise the
mitre saw head to its full
height. Loosen the mitre
table lock (7).
Crosscut
Mitre cut
Rotate the mitre table (14) until the pointer aligns with the desired angle.
Retighten the mitre table lock (7).
!
Warning! Be sure to tighten the mitre table lock (7) before making a cut.
Failure to do so could result in the table moving during the cut and cause
serious personal injury.
Place the work piece flat on the mitre table (14) with one edge securely against the
fence (18). If the board is warped, place the convex side against the fence (18). If the
concave side is placed against the fence, the board could break and jam the blade.
13
TOOL OPERATION (cont.)
When cutting long pieces of timber, support the opposite end of the timber with
the extension bars (16), a roller stand or a work surface that is level with the saw
table. Use the material clamp (19) to secure the work piece wherever possible.
It is possible to remove the material clamp (19) and moving it to the other side of
the table. Make sure the material clamp (19) is secured to the fence (18) before
using it.
Before turning on the saw, perform a practice run of the cutting operation to check
that there are no problems. Hold the switch handle (2) firmly and squeeze the on/off
switch (3). Allow the blade to reach maximum speed.
Press the on/off switch (3) and slowly lower the blade into and through the
workpiece.
Release the on/off switch (3) and allow the saw blade (6) to stop rotating before
lifting the blade (6) out of the workpiece. Also when performing a cut wait until the
blade (6) has come to a complete stop before removing the workpiece.
Cross-cutting (with slide action)
When cutting wide work pieces, first unscrew the
slide lock (27). Release the lock down knob (26),
raise the saw to its highest position and slide it
towards you. Hold the switch handle (2) firmly
and squeeze the on/off switch (3). Allow the
blade (6) to reach maximum speed.
Press the on/off switch (3) and slowly lower the
blade (6) into the workpiece and push it away
from you until the workpiece is cut. Release the on/off switch (3) and allow the
blade (6) to stop rotating before raising the blade (6) out of the workpiece. Also
when performing a cut wait until the blade (6) has come to a complete stop before
removing the workpiece.
Bevel cut
A bevel cut is made by cutting across the grain of the work piece with the mitre
saw blade (6) angled or beveled to the mitre table (14). The mitre table (14) is set
at the zero degree position and the mitre saw blade (6) set at 0º. Use the slide
action when cutting wide work piece.
Loosen the bevel lock (28) and move the saw to the left to the desired bevel angle
(between 0º and 45º). Tighten the bevel lock (28). Place the work piece flat on the
table with one edge securely against the fence (18). If the board is warped, place
the convex side against the fence. If the concave side is placed against the fence,
the board could break and jam the blade. When cutting long pieces of timber,
support the opposite end of the timber with the extension bars (16), a roller stand
or a work surface that is level with the saw table. Use the material clamp (19) to
secure the workpiece wherever possible.
14
TOOL OPERATION (cont.)
!
Warning! Be sure to tighten the bevel lock (28) before making a cut. Failure
to do so could result in the table moving during the cut, causing serious
personal injury.
It is possible to remove the clamp assembly (6) by loosening the clamp assembly lock
(7) and moving it to the other side of the table. Make sure the clamp assembly lock is
tight before using the clamp.
Before turning on the saw, perform a dry run of the cutting operation to check that
there are no problems.
Hold the operating handle (2) firmly and squeeze the on/off trigger switch (3). Allow
the blade to reach maximum speed and slowly lower the blade into and through
the workpiece.
Release the on/off switch (3) and allow the saw blade to stop rotating before raising
the blade out of the workpiece. Also when performing a cut wait until the blade has
come to a complete stop before removing the workpiece.
Compound mitre cut
A compound mitre cut involves using a mitre angle and
a bevel angle at the same time. It is used in making
picture frames, to cut mouldings, making boxes with
sloping sides and for roof framing. Always make a test
cut on a piece of scrap wood before cutting into the
good material. Use the slide action when cutting
wide workpieces.
Lift the mitre saw head to its full height. Loosen the mitre
table lock (7). Rotate the mitre table (14) until the pointer
aligns with the desired angle on the mitre scale (12). Retighten the mitre lock (7).
!
Warning! Be sure to tighten the mitre lock (7) before making a cut. Failure to
do so could result in the table moving during the cut, causing serious
personal injury.
Loosen the bevel lock (28) and move the motor head assembly to the left to the
desired bevel angle (between 0º and 45º).
Tighten the bevel lock (28). Place the workpiece flat on the table with one edge
securely against the fence (18). If the board is warped, place the convex side against
the fence. If the concave side is placed against the fence, the board could break and
jam the blade.
15
TOOL OPERATION (cont.)
Cutting long timber lengths
When cutting long pieces of timber, support the opposite end of the timber with
the extension bar (16), a roller stand or a work surface that is level with the saw
table. (8). Use the material clamp (19) to secure the workpiece wherever possible.
It is possible to remove the material clamp (19) and move it to the other side of
the table. Make sure the material clamp (19) is secured to the fence (18) before
using it. Before turning on the saw, perform a practice run of the cutting operation
to check that there are no problems.
Hold the switch handle (2) firmly and squeeze the on/off switch (3). Allow the
blade to reach maximum speed and slowly lower the blade into and through
the workpiece.
Release the on/off switch (3) and allow the saw blade (6) to stop rotating before
raising the blade out of the workpiece. Also when performing a cut wait until the
blade has come to a complete stop before removing the workpiece.
MAINTENANCE
!
Warning! Always ensure that the tool is switched off and the plug is
removed from the power point before making any adjustments or
performing maintenance procedures.
Power cord maintenance
If the supply cord needs replacing, the task must be carried out by an electrician
or a power tool repairer in order to avoid a safety hazard.
Cleaning
1. Keep the tool’s air vents unclogged and clean at all times.
2. Remove dust and dirt regularly. Cleaning is best done with a soft brush or a rag.
3. Re-lubricate all moving parts at regular intervals.
4. Never use caustic agents to clean plastic parts.
!
CAUTION: Do not use cleaning agents to clean the plastic parts of the
saw. A mild detergent on a damp cloth is recommended.
General inspection
Regularly check that all fixing screws are tight. They may vibrate loose over time.
16
SPARE PARTS
Limited spare parts are available subject to availability. Please contact a local
Bunnings Special Orders Desk to order the required spare parts.
Most common spare parts listed below
Spare Part
Part No.
Fence
Bolt, Blade M8x16 LH
Lower Guard
Table Insert
Carbon Brush (Pair)
SPOZSCMS1600WA-025
SPOZSCMS1600WA-075
SPOZSCMS1600WA-099
SPOZSCMS1600WA-021
SPOZSCMS1600WA-129
BLADES: You will find a selection of blades available from the Tool Shop at Bunnings
Warehouse.
DESCRIPTION OF SYMBOLS
V
Volts
Hz
Hertz
~
Alternating current
W
Watts
Revolutions or
reciprocation per minute
no
No load speed
/min
Double insulated
Regulator compliance mark
17
CARING FOR THE ENVIRONMENT
Power tools that are no longer usable should not be
disposed of with household waste but in an environmentally
friendly way. Please recycle where facilities exist. Check with
your local council authority for recycling advice.
Recycling packaging reduces the need for landfill and raw
materials. Reuse of recycled material decreases pollution in
the environment. Please recycle packaging where facilities
exist. Check with your local council authority for recycling
advice.
CONTENTS
1
1
1
1
x
x
x
x
Slide Compound Mitre Saw OZSMCS1600WA
Saw blade (fitted)
Material clamp
Hex key
2
1
1
1
x
x
x
x
Extension bars
Stabilising bar
Dust bag
Instruction manual
OZITO INDUSTRIES PTY LTD
AUSTRALIA (Head Office)
1-23 Letcon Drive, Bangholme Victoria, Australia, 3175
Telephone: 1800 069 486
Facsimile: +61 3 9238 5588
Website: www.ozito.com.au
Email: [email protected]
18
WARRANTY
YOUR WARRANTY FORM SHOULD BE RETAINED BY YOU AT ALL TIMES. IN ORDER
TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO
YOUR NEAREST BUNNINGS WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT.
PRIOR TO RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR
CUSTOMER SERVICE HELPLINE:
`Australia 1800 069 486
New Zealand 0508 069 486
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
The benefits provided under this warranty are in addition to other rights and remedies which
are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to a
replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if
the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this warranty,
however, where you have suffered any additional direct loss as a result of a defective product
you may be able to claim such expenses by contacting our customer service helpline above.
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from the original date of purchase
and is intended for DIY (Do It Yourself) use only. If a product is defective it will be replaced in
accordance with the terms of this warranty. Warranty excludes consumable parts, for example:
carbon brush, bearings, hex keys, spanners,saw blade, table insert and included accessories.
WARNING
The following actions will result in the warranty being void.
•
•
•
•
•
Professional, Industrial or high frequency use.
If the tool has been operated on a supply voltage other than that specified on the tool.
If the tool shows signs of damage or defects caused by or resulting from abuse, accidents
or alterations.
Failure to perform maintenance as set out within the instruction manual.
If the tool is disassembled or tampered with in any way.
OZITO
Australia/New Zealand (Head Office)
1-23 Letcon Drive, Bangholme, Victoria, Australia 3175
OW5