1. No category

MI 019-179
Instruction
May 2015
Flow Products Safety Information
MI 019-179 – May 2015
2
Contents
Figures ........................................................................................................................................... 7
Tables ............................................................................................................................................ 9
1. General Warnings .................................................................................................................... 11
Local Code Warning .................................................................................................................11
ATEX Warning .........................................................................................................................11
Intrinsically Safe Warning .........................................................................................................11
Process Fluid Warning...............................................................................................................11
Abrasive Fluid Warning.............................................................................................................12
Loss of Flow Signal Warning .....................................................................................................12
Parts Replacement Warning.......................................................................................................12
2. 83 Series Vortex Flowmeters .................................................................................................... 13
Electrical Certification Rating ...................................................................................................13
ATEX Compliance Documents ............................................................................................14
Type n Warning ........................................................................................................................14
PED Compliance ......................................................................................................................14
Maximum Working Pressure .....................................................................................................15
83F Flanged Body Flowmeters .............................................................................................15
83W Wafer Body Flowmeters...............................................................................................15
83S Sanitary Flowmeters ......................................................................................................15
Isolation Valves.....................................................................................................................15
Flowmeter Materials..................................................................................................................17
Flowmeter Body ...................................................................................................................17
Sensor Diaphragm and Fill Fluid..........................................................................................17
Sensor Replacement ..................................................................................................................18
3. 84 Series Vortex Flowmeters .................................................................................................... 19
Electrical Certification Rating ...................................................................................................19
ATEX and IECEx Warnings .................................................................................................21
ATEX Compliance Documents ............................................................................................21
IECEx Compliance Documents ...........................................................................................21
Explosionproof/Flameproof and Enclosure Warning .................................................................21
Connection Diagrams ...............................................................................................................22
PED Compliance ......................................................................................................................25
3
MI 019-179 – May 2015
Contents
Maximum Working Pressure .....................................................................................................26
84W Wafer Body Flowmeters...............................................................................................26
84S Sanitary Flowmeters ......................................................................................................26
Isolation Valves.....................................................................................................................26
Flowmeter Materials..................................................................................................................28
Flowmeter Body (Style A).....................................................................................................28
Flowmeter Body (Style B).....................................................................................................28
Sensor Material, Fill Fluid, and Temperature Range .............................................................29
Isolation Valve ......................................................................................................................29
Sensor Replacement ..................................................................................................................29
4. 84C Series Vortex Flowmeters ................................................................................................. 31
Electrical Certification Rating ...................................................................................................31
Explosionproof/Flameproof and Enclosure Warning .................................................................31
Connection Diagram ................................................................................................................31
PED Compliance ......................................................................................................................31
Maximum Working Pressure .....................................................................................................31
84CF Flanged Body Flowmeters...........................................................................................31
Flowmeter Materials..................................................................................................................32
Flowmeter Body ...................................................................................................................32
Sensor Material, Fill Fluid, and Temperature Range .............................................................32
Sensor Replacement ..................................................................................................................32
5. Mass Flow Products................................................................................................................. 35
CFS10 and CFS20 Mass Flowtubes ..........................................................................................35
Flowtube Identification: CFS10/CFS20 Connected to CFT51 ............................................35
Electrical Certification Rating ..............................................................................................35
Process Wetted Parts.............................................................................................................36
PED Compliance .................................................................................................................36
Maximum Working Pressure ................................................................................................37
CFS25 Mass Flowtubes .............................................................................................................38
Flowtube Identification: CFS25 Connected to CFT51.........................................................38
Electrical Certification Rating ..............................................................................................38
Process Wetted Parts.............................................................................................................39
PED Compliance .................................................................................................................39
Maximum Working Pressure ................................................................................................39
CFT51 Mass Flow Transmitters ................................................................................................40
Electrical Certification Rating ..............................................................................................40
ATEX Warnings ...................................................................................................................41
For Explosionproof Certifications:...................................................................................42
4
Contents
MI 019-179 – May 2015
ATEX Compliance Documents ............................................................................................42
IECEx Compliance Documents ...........................................................................................42
Operating Temperature Limits .............................................................................................42
Connection Diagrams ..........................................................................................................43
6. Magnetic Flow Products .......................................................................................................... 47
8000A Magnetic Flowtubes.......................................................................................................47
PED Compliance .................................................................................................................47
Process Pressure and Temperature Limits..............................................................................47
Process Wetted Parts.............................................................................................................48
9300A Magnetic Flowtubes.......................................................................................................48
PED Compliance .................................................................................................................48
Pressure and Temperature Limits ..........................................................................................48
Process Wetted Parts.............................................................................................................51
8300 Magnetic Flowtubes .........................................................................................................51
PED Compliance .................................................................................................................51
Ambient Temperature Limits................................................................................................52
Process Pressure and Temperature Limits..............................................................................52
Process Wetted Parts.............................................................................................................53
2800 Magnetic Flowtubes .........................................................................................................54
PED Compliance .................................................................................................................54
Ambient Temperature Limits................................................................................................54
Process Pressure and Temperature Limits..............................................................................54
Sizes 2.5 through 300 mm (1/10 through 12 in) .............................................................54
Sizes 350 through 900 mm (14 through 36 in)................................................................56
Sanitary Flowtubes ..........................................................................................................57
Process Wetted Parts.............................................................................................................57
9100A and 9200A Magnetic Flowtubes ....................................................................................57
PED Certification ................................................................................................................57
Process Pressure and Temperature Limits..............................................................................57
Process Wetted Parts.............................................................................................................57
5
MI 019-179 – May 2015
6
Contents
Figures
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Sample Flowmeter Junction Box Agency Plate ....................................................................13
Pressure-Temperature Limits with Isolation Valves ..............................................................16
Sample 84 Flowmeter Junction Box Agency Plate ...............................................................19
Intrinsically Safe Integral Mount Flowmeter........................................................................22
Intrinsically Safe Flowmeter with Remote Transmitter ........................................................23
Flameproof Integral Mount Transmitter..............................................................................24
Physical Earth Ground ........................................................................................................24
Flameproof Flowmeter with Remote Transmitter ................................................................25
Pressure -Temperature Limits with Isolation Valves .............................................................27
Flowtube in Zone 0 and Transmitter in Zone 2 Area ..........................................................43
Flowtube and Transmitter Located in Zone 2 Area..............................................................44
Flowtube in Zone 0 and Transmitter in Zone 1 (Flameproof ) Area .....................................45
Process Pressure and Temperature Limits PTFE-Lined Flowtubes — 830H through 8312
Sizes Only .....................................................................................................................52
Process Temperature and Pressure Limits for Flowtubes with PFA or PTFE Lining. ............55
Process Temperature and Pressure Limits - Sanitary Flowtubes ............................................57
7
MI 019-179 – May 2015
8
Figures
Tables
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Electrical Safety Specifications.............................................................................................14
Test Pressure........................................................................................................................18
Electrical Safety Specifications.............................................................................................20
Flanged Flowmeter..............................................................................................................28
Male NPT Flowmeter .........................................................................................................28
Material, Fill Fluid, and Temperature Range .......................................................................29
Maximum Test Pressure ......................................................................................................30
Material, Fill Fluid, and Temperature Range .......................................................................32
Maximum Test Pressure ......................................................................................................33
CFS10, CFS20 Electrical Safety Specification When Used with CFT51..............................35
Process Temperature Range for Electrical Safety Design Codes When Used with CFT51....36
End Connection Process Temperature/Pressure Limits ........................................................37
Flowtube Process Temperature/Pressure Limits - Threaded End Connections .....................38
CFS25 Electrical Safety Specification When Used with CFT51 ..........................................38
Flowtube Process Pressure Rating ........................................................................................39
CFT51 Electrical Safety Specifications ................................................................................40
Process Pressure and Temperature Limits: Wafer Body Flowtubes with Ceramic Lining ......47
Process Pressure and Temperature Limits: Wafer Body Flowtubes with PFA Lining.............48
Transmitter Remote Mounted PFA-Lined Flowtubes ..........................................................49
Transmitter Remote Mounted PTFE-Lined Flowtubes........................................................49
Transmitter Remote Mounted Polyurethane-Lined Flowtubes.............................................49
Transmitter Integrally Mounted PFA-Lined Flowtubes........................................................50
Transmitter Integrally Mounted PTFE-Lined Flowtubes .....................................................50
Transmitter Integrally Mounted Polyurethane-Lined Flowtubes ..........................................50
Flange Pressure-Temperature Limits for PFA-Lined/PTFE-lined Flowtubes ........................51
Process Pressure and Temperature Limits
PTFE-Lined Flowtubes — 8314 through 8324 Sizes Only ..........................................52
Process Pressure and Temperature Limits
Polyurethane-Lined Flowtubes — 8302 through 8336 Sizes..........................................53
Process Pressure and Temperature Limits
Neoprene-Lined Flowtubes — 8314 through 8336 Sizes...............................................53
Process Temperature and Pressure Limits for Polyurethane Lining.......................................55
Process Pressure and Temperature Limits - ptfe-Lined Flowtubes (2814 - 2824 Sizes Only) 56
Process Pressure and Temperature Limits - Polyurethane-Lined Flowtubes ..........................56
Process Pressure and Temperature Limits - Neoprene-Lined Flowtubes ...............................56
9
MI 019-179 – May 2015
10
Tables
1. General Warnings
Local Code Warning
! WARNING
These products must be installed to meet all applicable local installation regulations,
such as hazardous location requirements, electrical wiring codes, and mechanical
piping codes. Persons involved in the installation must be trained in these code
requirements to ensure that the installation takes maximum advantage of the safety
features designed into the flowmeter.
ATEX Warning
! WARNING
Apparatus marked as Category 1 equipment and used in hazardous areas requiring
this category must be installed in such a way that, even in the event of rare incidents,
the versions with an aluminum alloy enclosure can not be an ignition source due to
impact and friction.
Intrinsically Safe Warning
! WARNING
Since live maintenance is not specified, to prevent ignition of flammable atmospheres,
disconnect power before servicing unless the area is certified to be nonhazardous.
Process Fluid Warning
! WARNING
If process containing parts are to be disassembled:
1. Make sure that process fluid is not under pressure or at high temperature.
2. Take proper precautions concerning leakage or spillage of any toxic or otherwise
dangerous fluid. Follow any Material Safety Data Sheet (MSDS) recommendations.
11
MI 019-179 – May 2015
1. General Warnings
! WARNING
These flowmeters are built using materials that are corrosion resistant to a wide variety
of fluids. However, with aggressive fluids, a potential exists for corrosive failure.
Therefore, verify the material compatibility with the NACE guidelines and/or user
knowledge of the flowmeter material compatibility with the process fluid at operating
conditions.
Abrasive Fluid Warning
! WARNING
Fluids containing abrasive particles and flowing at high rates can cause significant
wear to pipes. If these conditions exist, check the flowmeter periodically for wear.
Loss of Flow Signal Warning
! WARNING
If the flowrate signal appears to have a calibration shift or goes to zero, check the
flowmeter for corrosion or wear.
Parts Replacement Warning
! WARNING
If replacing parts, do not use parts made of other materials or that in any other way
change the product as described in the model code on the data plate.
12
2. 83 Series Vortex Flowmeters
When the flowmeter is remotely mounted, the junction box on the flowtube body has an agency
plate showing its hazardous location rating. See Figure 1.
Figure 1. Sample Flowmeter Junction Box Agency Plate
Electrical Certification Rating
The electrical safety design code is printed on the data plate as part of the model code. The
location of the code within the model number is shown below:
83F-A02S2SDTAA
ELECTRICAL SAFETY DESIGN CODE
See Table 1 to identify this code. The type of protection is also marked on the data plate.
13
MI 019-179 – May 2015
2. 83 Series Vortex Flowmeters
Table 1. Electrical Safety Specifications
Testing Laboratory,
Type of Protection, and
Area Classification
Application Conditions
Electrical Safety
Design Code
ATEX II 2 G, EEx ib IIC.
83 (F and W) -A, -D, and -T
Temperature Class T4 at 0.8 W
at -20 to +80°C.
Temperature Class T5 at 0.7 W
at -20 to +40°C.
Temperature Class T6 at 0.5 W
at -20 to +40°C.
E
ATEX II 3 G, EEx nL IIC.
83 (F and W) -A, -D, and -T
Temperature Class T4 at -20 to +80°C.
Temperature Class T5 at -20 to +40°C.
Temperature Class T6 at -20 to +40°C.
N
NOTE
These flowmeters have been designed to meet the electrical safety descriptions listed in
Table 1. For detailed information, or status of testing laboratory
approvals/certifications, contact Global Customer Support.
ATEX Compliance Documents
EN 50014: 1997
EN 50020: 1994
EN 50021: 1999
Type n Warning
! WARNING
On flowmeters certified for ATEX protection nL, the threaded housing covers must
be installed.
PED Compliance
The 83 Series Vortex Flowmeters are fully compliant with the European Pressure Equipment
Directive as process piping devices for Fluid Groups 1 and 2 for Gas and Liquid applications. The
product data plate is marked accordingly for the line sizes and pressure ratings for the above fluid
groups. Contact Global Customer Support for the specific product category classification for any
given line size and pressure rating.
Line sizes and pressure ratings that are categorized as Category II or III carry the notifying body
(DNV) number 0575 under the CE mark. The PED compliance marking is affixed only to
products that have the ATEX electrical safety certifications and carry the ATEX Notify Body
number 0344.
14
2. 83 Series Vortex Flowmeters
MI 019-179 – May 2015
Maximum Working Pressure
83F Flanged Body Flowmeters
For specific temperature/pressure ratings for different materials and flanges, see MI 019-189.
83W Wafer Body Flowmeters
For specific temperature/pressure ratings for different materials and flanges, see MI 019-189.
83S Sanitary Flowmeters
For specific temperature/pressure ratings for different materials and flanges, see MI 019-173.
Isolation Valves
Flowmeters equipped with an isolation valve have a maximum pressure rating of 1440 psi at
100°F (99 bar at 38°C). Isolation valves used with standard temperature range and with extended
temperature range flowmeters are further limited to values shown in Figure 2. The temperature
range of your flowmeter is found within the model number on the data label as follows:
83F-A02S2KDTAA
ISOLATION VALVE (S or T)
TEMPERATURE RATING
TEMPERATURE RATING
Standard temp = D, F, R, OR S
Extended temp = C OR T
15
MI 019-179 – May 2015
2. 83 Series Vortex Flowmeters
Figure 2. Pressure-Temperature Limits with Isolation Valves
200°F
FLUOROLUBE
SENSOR
LIMIT
800°F
400°F
SILICON
SENSOR
LIMIT
EXTENDED
TEMP. LIMIT
(NO FILL)
1600
1440
1400
EXTENDED TEMP.
VALVE WITH
GRAPHITE SEAT
P-T LIMITS
WITH
ISOLATION
VALVE
PROCESS PRESSURE, psig
1200
1000
845 psig
800
STANDARD TEMP.
VALVE WITH
GLASS-FILLED
ptfe SEAT
LINEARLY
INTERPOLATED
600
500
400
200
0
-20
0
100
200
300
400
500
600
PROCESS TEMPERATURE, °F
90°C
FLUOROLUBE
SENSOR
LIMIT
120
38°C
800
200°C
430°C
EXTENDED
TEMP. LIMIT
(NO FILL)
SILICON
SENSOR
LIMIT
EXTENDED TEMP.
VALVE WITH
GRAPHITE SEAT
100
PROCESS PRESSURE, bar
700
P-T LIMITS
WITH
ISOLATION
VALVE
80
58.3 bar
60
STANDARD TEMP.
VALVE WITH
GLASS-FILLED
ptfe SEAT
LINEARLY
INTERPOLATED
40
35
204°C
20
0
0
-10
16
50
90
100
150
250
350
200
300
PROCESS TEMPERATURE, °C
400
430
450
2. 83 Series Vortex Flowmeters
MI 019-179 – May 2015
Flowmeter Materials
Flowmeter Body
The flowmeter body material is shown on the data label.
♦ CF8M = cast 316 stainless steel body and shedder per ASTM A351 grade CF8M
♦ 304 SS = welded pipe and flange body with 304 ss pipe and shedder per ASTM 312
and 304 ss flanges per ASTM 182
♦ 304/A105 = welded pipe and flange body with 304 ss pipe and shedder per
ASTM 312 and carbon steel flanges per ASTM A105
♦ CW2M = cast Nickel alloy(1) body and shedder per ASTM A494-CW2M
♦ 316 SS = AISI Type 316 stainless steel.
Sensor Diaphragm and Fill Fluid
The sensor diaphragm and fill fluid for the 83F and 83W Flowmeters are found within the model
number on the data label as follows:
83F-A02S2KDTAA
DIAPHRAGM MATERIAL AND FILL FLUID
Code
Diaphragm Material
Fill Fluid
D
Nickel alloy CW2M (a)
Fluorolube
F
316L Stainless Steel
Fluorolube
R
Nickel alloy CW2M (a)
Silicone (DC550)
S
316L Stainless Steel
Silicone (DC550)
C
Nickel alloy CW2M (a)
Unfilled
T
316L Stainless Steel
Unfilled
a. Equivalent to Hastelloy® C-4C.
The sensor diaphragm for the 83S Flowmeter is 316 Stainless Steel (meets both 316 and 316L
properties); the fill fluid is Silicone (DC550).
The isolation valve materials are as follows:
Valve Body:
ASTM A351 grade CF8M stainless steel
Valve Ball:
AISI Type 316 stainless steel
Valve Seats:
Glass Filled ptfe for standard temperature flowmeters
Graphite for extended temperature flowmeters
The temperature range of your flowmeter is found within the model number on the data label as
follows:
83F-A02S2KDTAA
TEMPERATURE RATING
STANDARD TEMP = D, F, R, OR S
EXTENDED TEMP = C OR T
1. Equivalent to Hastelloy® C-4C. Hastelloy® is a registered trademark of Haynes International Inc.
17
MI 019-179 – May 2015
2. 83 Series Vortex Flowmeters
Sensor Replacement
! WARNING
To prevent injury from escaping process fluids, to maintain agency certification of this
product, and to prove the integrity of the parts and workmanship in containing
process pressure, a hydrostatic pressure test must be performed after the sensor
replacement is complete. The flowmeter must hold the appropriate pressure from
Table 2 for one minute without leaking.
Table 2. Test Pressure
Model
83F
83W
18
End Connection
Test Pressure
ANSI Class 150
450 psi
PN 16
3.2 MPa
ANSI Class 300
1125 psi
PN 40
6 MPa
PN 64
9.6 MPa
ANSI Class 600
2250 psi
PN 100
15 MPa
All
15 MPa (2250 psi)
3. 84 Series Vortex Flowmeters
When the flowmeter is remotely mounted, the junction box on the flowtube body has an agency
plate showing its hazardous location rating. See Figure 3.
Figure 3. Sample 84 Flowmeter Junction Box Agency Plate
MODEL 84
VORTEX FLOWMETER
Remote Sensor Housing
MODEL NO:
S/N:
ST :
DO NOT OPEN WHILE ENERGIZED
CAUTION: CABLE ENTRIES 1/2-14 NPT
IP 66 ENCLOSURE
WARNING: EXPLOSION
HAZARD -SUBSTITUTION
OF COMPONENTS MAY
IMPAIR SAFETY.
WARNING: ENSURE AREA IS KNOWN
TO BE NON-HAZARDOUS BEFORE
REMOVING COVER.
WARNING: EXPLOSION
HAZARD- DO NOT DISCONNECT
EQUIPMENT UNLESS POWER HAS
BEEN TURNED OFF OR THE AREA
IS KNOWN TO BE NON -HAZARDOUS.
WARNING: TO PREVENT IGNITION
OF FLAMMABLE OR COMBUSTIBLE
ATMOSPHERES, DISCONNECT
POWER BEFORE SERVICING.
Sira 06ATEX2067X
II 1G II 2D
Ex ia IIC T4 Ga (Ta = -40°C to +80°C)
Ex tb IIIC T103°C Db
SEE CERTIFICATE FOR ELECTRICAL DATA.
0344
INVENSYS SYSTEMS INC.
FOXBORO, MA., U.S.A. 02035
Electrical Certification Rating
The electrical safety design code is printed on the data plate as part of the model code. The
location of the code within the model number is shown below:
84F-T02S2SRTJE
ELECTRICAL SAFETY CODE
See Table 3 to identify this code. The type of protection is also marked on the data plate.
NOTE
These flowmeters have been designed to meet the electrical safety descriptions listed in
Table 3. For detailed information, or status of testing laboratory
approvals/certifications, contact Global Customer Support.
19
MI 019-179 – May 2015
3. 84 Series Vortex Flowmeters
Table 3. Electrical Safety Specifications
Testing Laboratory, Type of Protection, and Area
Classification (a) (b)
Application Conditions
Electrical
Safety
Code
ATEX Specifications
ATEX intrinsically safe: II 1G II 2D
Ex ia IIC T4 Ga
Ex tb IIIC T103°C Db
Sira 06ATEX2067X
Integrally mounted or remote mounted (electronics
and junction box).
Temperature Class T4; Ta = -40° to +80°C
E
ATEX flameproof: II 2/1 (1) G II 2D
Ex d [ia Ga] ia IIC T4 Gb
Ex tb IIIC T85°C Db
Sira 06ATEX2067X
Integrally mounted electronics.
Temperature Class T4; Ta = -20° to +80°C
H
ATEX flameproof: II 2/1 (1) G II 2D
Ex d [ia Ga] IIC T4 Gb
Ex tb IIIC T85°C Db
Sira 06ATEX2067X
Electronics housing of remote mounted version.
Temperature Class T4; Ta = -20° to +80°C
CSA Specifications( (c))
CSA intrinsically safe for Class I, II, III, Div. 1,
Groups A, B, C, D, E, F, and G.
Also Zone certified intrinsically safe Ex ia IIC
Temperature Class T4; Ta = -40 ° to +80°C
C
CSA explosionproof with IS sensor connection for Temperature Class T5; Ta = 60°C
Class I, Div. 1, Groups B, C, and D;
dust-ignitionproof for Class II, Div. 1,
Groups E, F, and G; Class III, Div. 1
Also Zone certified Ex d [ia] IIC.
Temperature Class T5; Ta = -40 ° to +80°C
D
CSA for Class I, Div. 2, Groups A, B, C, and D;
Class II, Div. 2, Groups F and G; Class III, Div. 2
Temperature Class T4; T=80°C
M
FM intrinsically safe for Class I, II, III, Div. 1,
Groups A, B, C, D, E, F, G
Also Zone approved AEx ia IIC
Temperature Class T4; Ta = 80°C
F
FM explosionproof with IS sensor connection for
Class I, Div. 1, Groups B, C, and D;
dust-ignitionproof for Class II, Div. 1, Groups E, F,
and G; Class III, Div. 1
Temperature Class T5; Ta = 85°C
G
FM nonincendive for Class I, Div. 2, Groups A, B,
C, and D;
Class II, Div. 2, Groups F and G;
Class III, Div. 2
Temperature Class T4; Ta = 80°C
K
IECEx intrinsically safe: Ex ia IIC T4 Ga
Ex tb IIIC T103°C Db
Temperature Class T4; Ta = -40° to +80°C
L
IECEx flameproof: Ex d [ia Ga] ia IIC T4 Gb
Ex tb IIIC T85°C Db
Integrally mounted electronics.
Temperature Class T4; Ta = -20° to +80°C
B
IECEx flameproof: Ex d [ia Ga] IIC T4 Gb
Ex tb IIIC T85°C Db
Electronic housing of remote mounted version.
Temperature Class T4; Ta = -20° to +80°C
FM Specifications
IECEx Specifications
NEPSI Specifications
NEPSI intrinsically safe, Zone 0, Ex ia IIC
Temperature Class T4; Ta = -40 ° to +80°C
R
NEPSI flameproof, Zone 1, Ex d IIC
(except acetylene)
Temperature Class T5; Ta = -40 ° to +85°C
S
CE Specifications
Unit with CE mark and PED controls and records
Y
Unit does not have CE mark; not to be installed in European Union (EU) countries
Z
a. With intrinsically safe approvals and certifications with a 24 V dc supply, an active barrier is required.
b. When the LCD indicator is used, the low temperature limit is -20°C.
c. Refer to MI 019-177 for FM and CSA Connection Diagrams.
20
3. 84 Series Vortex Flowmeters
MI 019-179 – May 2015
ATEX and IECEx Warnings
! WARNING
1. Ensure area is known to be nonhazardous before removing cover.
2. Do not open while circuits are alive.
3. Do not open when energized or when an explosive atmosphere may be present.
4. Explosion Hazard: Substitution of components may impair intrinsic safety or
Division 2 approvals.
5. Explosion Hazard: Do not disconnect equipment unless power has been turned off
or the area is known to be nonhazardous.
For explosionproof certifications:
! WARNING
1. Keep cover tight while circuits are alive unless area is known to be nonhazardous.
2. To prevent ignition of flammable or combustible atmospheres, disconnect power
before servicing.
3. The Model 84 Vortex electronics housing and housing covers contain more than
10% aluminum and is considered to constitute a potential risk of ignition by
impact or friction. Care must be taken to prevent impact and friction when
installing or using the flowmeters in a Zone 0 installation.
! DANGER
For nonintrinsically safe installations, to prevent a potential explosion in a Zone 1
hazardous area, de-energize the transmitter before you remove the threaded housing
cover. Failure to comply with this warning could result in an explosion resulting in
severe injury or death.
ATEX Compliance Documents
EN 60079-1:2007
EN 60079-26:2007
EN 60079-31:2008
IEC 60079-0:2011
IEC 60079-11:2011
IECEx Compliance Documents
IEC 60079-0:2011 Ed 6
IEC 60079-26:2007 Ed 2
IEC 60079-1:2007 Ed 6
IEC 60079-31:2008 Ed 1
IEC 60079-11:2011 Ed 6
Explosionproof/Flameproof and Enclosure Warning
! WARNING
To prevent possible explosion and to maintain explosionproof/flameproof and dustignitionproof protection, plug unused openings with the provided metal pipe plug.
This plug must be engaged a minimum of five full threads. The threaded housing
21
MI 019-179 – May 2015
3. 84 Series Vortex Flowmeters
covers must be installed. Turn covers to seat O-ring into the housing and then
continue to hand tighten until the cover contacts the housing metal-to-metal.
Connection Diagrams
Figure 4. Intrinsically Safe Integral Mount Flowmeter
HAZARDOUS LOCATION
UNCLASSIFIED LOCATION
INTRINSICALLY SAFE
ATEX: II 1G II 2D Ex ia IIC T4 Ga
Ex tb IIIC T103°C Db
IECEx: Ex ia IIC T4 Ga
Ex tb IIIC T103°C Db
Model 84)
(Integral Mount)
ENTITY PARAMETERS
(Loop Interface)
Ui = 30 V
Ii = 110 mA
Pi = 0.8 W
Ci = 0 nF
Li = 0 mH
ENTITY PARAMETERS
(Pulse Interface)
Ui = 30 V
Ii = 110 mA
Pi = 0.8 W
Ci = 0.3 nF
Li = 0 mH
Loop Interface
+
+
–
–
+
AGENCY ENTITY APPROVED
ASSOCIATED APPARATUS
OR BARRIER
–
G
Pulse Interface
+
+
–
–
+
AGENCY ENTITY APPROVED
ASSOCIATED APPARATUS
OR BARRIER
–
G
Uo = 6.51V
Io = 6.6 mA
OPTIONAL PULSE OUTPUT IF AVAILABLE
INTRINSICALLY SAFE
GROUND
NOTE: The negative terminal loop power shall only be connected to a load resistor to the negative side
of the incoming power supply. Consult certificate
22
3. 84 Series Vortex Flowmeters
MI 019-179 – May 2015
Figure 5. Intrinsically Safe Flowmeter with Remote Transmitter
UNCLASSIFIED LOCATION
HAZARDOUS LOCATION
INTRINSICALLY SAFE
ATEX: II 1G II 2D Ex ia IIC T4 Ga
Ex tb IIIC T103°C Db
IECEx: Ex ia IIC T4 Ga
Ex tb IIIC T103°C Db
Model 84
(Remote Transmitter)
ENTITY PARAMETERS
(Loop Interface)
Ui = 30 V
Ii = 110 mA
Pi = 0.8 W
Ci = 0 nF
Li = 0 mH
ENTITY PARAMETERS
(Pulse Interface)
Ui = 30 V
Ii = 110 mA
Pi = 0.8 W
Ci = 0.3 nF
Li = 0 mH
Loop Interface
+
+
–
–
AGENCY ENTITY APPROVED
ASSOCIATED APPARATUS
OR BARRIER
+
–
G
Pulse Interface
+
+
–
–
+
AGENCY ENTITY APPROVED
ASSOCIATED APPARATUS
OR BARRIER
–
G
Uo = 6.51V
Io = 6.6 mA
OPTIONAL PULSE OUTPUT IF AVAILABLE
REMOTE CABLE
(SEE NOTE 2)
INTRINSICALLY SAFE
GROUND
PREAMPLIFIER HOUSING
AND FLOWTUBE ONLY
NOTES
1. THE NEGATIVE TERMINAL LOOP POWER SHALL ONLY BE CONNECTED TO A LOAD RESISTOR
TO THE NEGATIVE SIDE OF THE INCOMING POWER SUPPLY. CONSULT CERTIFICATE
2. INTRINSICALLY SAFE TRANSMITTER/FLOWTUBE CONNECTION. CONSULT CERTIFICATE.
23
MI 019-179 – May 2015
3. 84 Series Vortex Flowmeters
Figure 6. Flameproof Integral Mount Transmitter
HAZARDOUS LOCATION
UNCLASSIFIED LOCATION
FLAMEPROOF
ATEX: II 2/1 (1) G II 2D
Ex d [ia Ga] ia IIC T4 Gb
Ex tb IIIC T85°C Db
IECEx: Ex d [ia Ga] ia IIC T4 Gb
Ex tb IIIC T85°C Db
Model 84
(Integral Mount)
FLAMEPROOF CONDUIT
CONSULT CERTIFICATE
+
SUPPLY
4-20 mA
–
PHYSICAL EARTH GROUND (See Figure 7)
FLAMEPROOF CONDUIT
CONSULT CERTIFICATE
+
PULSE (if present)
–
Figure 7. Physical Earth Ground
M20 CONDUIT CONNECTION
(2 PLACES)
+
+
P
U
L
S
E
–
PHYSICAL EARTH GROUND
24
3. 84 Series Vortex Flowmeters
MI 019-179 – May 2015
Figure 8. Flameproof Flowmeter with Remote Transmitter
HAZARDOUS LOCATION
UNCLASSIFIED LOCATION
FLAMEPROOF
ATEX Electronics Housing
II 2 (1) G II 2D
Ex d [ia Ga] IIC T4 Gb
Ex tb IIIC T85°C Db
ATEX Flowtube Junction Box II 1G II 2D
Ex ia IIC T4 Ga
Ex tb IIIC T103°C Db
IECEX Electronics Housing
Ex d [ia Ga] IIC T4 Gb
Ex tb IIIC T85°C Db
IECEX Flowtube Junction
Box
Ex ia IIC T4 Ga
Ex tb IIIC T103°C Db
Model 84
(Remote Transmitter)
FLAMEPROOF CONDUIT
CONSULT CERTIFICATE
+
SUPPLY
4-20 mA
–
PHYSICAL EARTH GROUND (See Figure 7)
+
PULSE (if present)
–
REMOTE CABLE
(SEE NOTE)
FLAMEPROOF CONDUIT
CONSULT CERTIFICATE
PREAMPLIFIER HOUSING
AND FLOWTUBE ONLY
NOTE: INTRINSICALLY SAFE TRANSMITTER/FLOWTUBE CONNECTION. CONSULT CERTIFICATE.
PED Compliance
The 84 Series Vortex Flowmeters are fully compliant with the European Pressure Equipment
Directive as process piping devices for Fluid Groups 1 and 2 for Gas and Liquid applications. The
product data plate is marked accordingly for the line sizes and pressure ratings for the above fluid
groups. Contact Global Customer Support for the specific product category classification for any
given line size and pressure rating.
Line sizes and pressure ratings that are categorized as Category II or III carry the notifying body
(DNV) number 0575 under the CE mark. The PED compliance marking is affixed only to
products that have the ATEX electrical safety certifications and carry the ATEX Notify Body
number 0344.
25
MI 019-179 – May 2015
3. 84 Series Vortex Flowmeters
Maximum Working Pressure
For specific temperature/pressure ratings for different materials and flanges, see MI 019-202 and
MI 019-211.
84W Wafer Body Flowmeters
For specific temperature/pressure ratings for different materials and flanges, see MI 019-202 and
MI 019-211.
84S Sanitary Flowmeters
For specific temperature/pressure ratings for different materials and flanges, see MI 019-205 and
MI 019-214.
Isolation Valves
Flowmeters equipped with an isolation valve have a maximum pressure rating of 1440 psi at
100°F (99 bar at 38°C). Isolation valves used with standard temperature range and with extended
temperature range flowmeters are further limited to values shown in Figure 9. The temperature
range of your flowmeter is found within the model number on the data label as follows:
84F-T02S6KDVJE
TEMPERATURE RANGE
ISOLATION VALVE (K or L)
26
STD TEMP = D, F, R, or S
EXT TEMP = C or T
3. 84 Series Vortex Flowmeters
MI 019-179 – May 2015
Figure 9. Pressure -Temperature Limits with Isolation Valves
200°F
800°F
400°F
SILICON
SENSOR
LIMIT
FLUOROLUBE
SENSOR
LIMIT
EXTENDED
TEMP. LIMIT
(NO FILL)
1600
1440
1400
EXTENDED TEMP.
VALVE WITH
GRAPHITE SEAT
P-T LIMITS
WITH
ISOLATION
VALVE
PROCESS PRESSURE, psig
1200
1000
845 psig
800
STANDARD TEMP.
VALVE WITH
GLASS-FILLED
ptfe SEAT
LINEARLY
INTERPOLATED
600
500
400
200
0
-20
0
100
200
300
400
500
600
PROCESS TEMPERATURE, °F
90°C
FLUOROLUBE
SENSOR
LIMIT
120
38°C
800
200°C
430°C
EXTENDED
TEMP. LIMIT
(NO FILL)
SILICON
SENSOR
LIMIT
EXTENDED TEMP.
VALVE WITH
GRAPHITE SEAT
100
PROCESS PRESSURE, bar
700
P-T LIMITS
WITH
ISOLATION
VALVE
80
58.3 bar
60
STANDARD TEMP.
VALVE WITH
GLASS-FILLED
ptfe SEAT
LINEARLY
INTERPOLATED
40
35
204°C
20
0
0
-10
50
90
100
150
250
350
200
300
PROCESS TEMPERATURE, °C
400
430
450
27
MI 019-179 – May 2015
3. 84 Series Vortex Flowmeters
Flowmeter Materials
Flowmeter Body (Style A)
The flowmeter body material is shown on the data label.
♦ CF8M = cast 316 stainless steel body and shedder per ASTM™ A351 grade CF8M
♦ 304 SS = welded pipe and flange body with 304 ss pipe and shedder per ASTM 312
and 304 ss flanges per ASTM 182
♦ 304/A105 = welded pipe and flange body with 304 ss pipe and shedder per
ASTM 312 and carbon steel flanges per ASTM A105
♦ CW2M = cast Nickel alloy CW2M(1) body and shedder per ASTM A494
♦ 316 SS = AISI Type 316 stainless steel.
Flowmeter Body (Style B)
The flowmeter body material is shown in Table 4.
Table 4. Flanged Flowmeter
Line Sizes
3/4 to 4 inch
(Codes 3Q to 04)
6 to 8 inch
(Codes 06 to 08)
10 and 12 inch
(Codes 10 and 12)
Body/Shedder Bar
Flange
Cast 316 SS, CF8M
316 SS per ASTM A182 Grade F316/F316L
Cast Duplex SS per ASTM A995 Grade 4A,
CD3MN
Duplex SS per ASTM A182 Grade F51
Cast nickel alloy, CX2MW (a)
Nickel alloy N06022 (a) per ASTM B462
Cast 316 SS, CF8M
304 SS per ASTM A182 Grade F304/304L
Cast Duplex SS per ASTM A995 Grade 4A,
CD3MN
Duplex SS per ASTM A182 Grade F51
Cast nickel alloy, CX2MW (a)
Nickel alloy N06022 (a) per ASTM B462
Fabricated 304 SS per ASTM 312
304 SS per ASTM A182 Grade F304/F304L
Fabricated Duplex SS per ASTM A790
Duplex SS per ASTM A182 Grade F51
Fabricated nickel alloy UNS N06022 (a) per ASTM Nickel alloy N06022 (a) per ASTM B462
B622
a. Equivalent to Hastelloy® C-22. Hastelloy is a registered trademark of Haynes International, Inc.
NOTE
An option for a threaded MNPT is available. Materials for that option are shown in
Table 5.
Table 5. Male NPT Flowmeter
Line Sizes
Body/Shedder Bar
1 inch (Code 01)
Cast 316 SS, CF8M
Cast 316 SS, integrally cast to body
2 inch (Code 02)
Cast 316 SS, CF8M
316 SS
1. Equivalent to Hastelloy® C-4C.
28
NPT Connection
3. 84 Series Vortex Flowmeters
MI 019-179 – May 2015
Sensor Material, Fill Fluid, and Temperature Range
The sensor diaphragm material, fill fluid, and temperature range for the 84F and 84W
Flowmeters are found within the model number on the data label as follows:
84F-T02S1SRTJF
DIAPHRAGM MATERIAL, FILL FLUID, AND TEMPERATURE RANGE
Table 6. Material, Fill Fluid, and Temperature Range
Code
Diaphragm Material
Fill Fluid
Temperature Range
D
Nickel alloy CW2M (a)
Fluorolube
0 to 200°F (-20 to +90°C)
F
Stainless Steel CF3M
Fluorolube
0 to 200°F (-20 to +90°C)
R
Nickel alloy CW2M (a)
Silicone
0 to 400°F (-20 to +200°C)
S
Stainless Steel Type CF3M
Silicone
0 to 400°F (-20 to +200°C)
C (b)
Nickel alloy CW2M (a)
Unfilled
400° to 800°F (200° to 430°C)
T (b)
Stainless Steel Type CF3M
Unfilled
400° to 800°F (200° to 430°C)
A (c)
Nickel alloy CW2M (a)
Unfilled
400° to 700°F (200° to 370°C)
B (c)
Stainless Steel Type CF3M
Unfilled
400° to 700°F (200° to 370°C)
E (c)
Nickel alloy CW2M (a)
Unfilled
400° to 800°F (200° to 430°C)
G (c)
Stainless Steel Type CF3M
Unfilled
400° to 800°F (200° to 430°C)
a. Equivalent to Hastelloy® C-4C.
b. Style A Vortex Flowmeters only.
c. Style B Vortex Flowmeters only.
The sensor diaphragm for the 84S Flowmeter is 316 Stainless Steel (meets both 316 and 316L
properties); the fill fluid is Silicone (DC550); the temperature range is 0 to 400°F (-20 to
+200°C).
Isolation Valve
The isolation valve materials are as follows:
Valve Body:
ASTM A351 grade CF8M stainless steel
Valve Ball:
AISI Type 316 stainless steel
Valve Seats:
Glass Filled ptfe for standard temperature flowmeters
Graphite for extended temperature flowmeters
Sensor Replacement
! CAUTION
For ATEX or IECEx certified flameproof units, take special care not to scar, mar, ding,
or dent the surface of the sensor stem during assembly. This is critical to the integrity
of the flameproof surface finish.
29
MI 019-179 – May 2015
3. 84 Series Vortex Flowmeters
! WARNING
To prevent injury from escaping process fluids, to maintain agency certification of this
product, and to prove the integrity of the parts and workmanship in containing
process pressure, a hydrostatic pressure test must be performed after the sensor
replacement is complete. The flowmeter must hold the appropriate pressure from
Table 32 for one minute (10 minutes to meet PED requirements) without leaking.
It is important that the correct sensor replacement kits are used for 84F (Style B) and for ATEX
applications per MI 019-209.
Table 7. Maximum Test Pressure
Test Pressure
Model
84F
84W
End Connection
Duplex SS, Nickel alloy
CW2M (a) (1.5X MWP)
Carbon Steel
(MWP)
ANSI Class 150
413 psi
435 psi
428 psi
ANSI Class 300
1080 psi
1125 psi
1110 psi
ANSI Class 600
2160 psi
2250 psi
2220 psi
ANSI Class 900
3240 psi
3375 psi
3330 psi
ANSI Class 1500
5400 psi
5625 psi
5558 psi
PN 16
2.4 Mpa
2.4 Mpa
2.4 Mpa
PN 25
3.8Mpa
3.8Mpa
3.8Mpa
PN 40
6.0 Mpa
6.0 Mpa
6.0 Mpa
PN 63
9.5 Mpa
9.5 Mpa
9.5 Mpa
PN 100
15.0 Mpa
15.0 Mpa
15.0 Mpa
PN 160
24.0 Mpa
24.0 Mpa
24.0 Mpa
All
15 MPa (2250 psi)
a. Equivalent to Hastelloy® C-4C.
30
316 SS
(1.5X MWP)
4. 84C Series Vortex Flowmeters
All safety information for the 84 Series Vortex Flowmeters described in Chapter 3, “84 Series
Vortex Flowmeters” applies to the 84 Series. Only information unique to the 84C Series is
provided in this chapter.
Electrical Certification Rating
The electrical certification rating for the 84C Vortex Flowmeter is the same as the 84 Series
(Style B). See “Electrical Certification Rating” on page 19.
Explosionproof/Flameproof and Enclosure Warning
The explosionproof/flameproof and enclosure warning for the 84C Vortex Flowmeter is the same
as the 84 Series (Style B). See “Explosionproof/Flameproof and Enclosure Warning” on page 21.
Connection Diagram
The connection diagrams for the 84C Vortex Flowmeter are the same as the 84 Series (Style B).
See “Connection Diagrams” on page 22.
PED Compliance
The 84C Series Vortex Flowmeters are fully compliant with the European Pressure Equipment
Directive as process piping devices for Fluid Groups 1 and 2 for Gas and Liquid applications. The
product data plate is marked accordingly for the line sizes and pressure ratings for the above fluid
groups. Contact Global Customer Support for the specific product category classification for any
given line size and pressure rating.
Line sizes and pressure ratings that are categorized as Category II or III carry the notifying body
(DNV) number 0575 under the CE mark. The PED compliance marking is affixed only to
products that have the ATEX electrical safety certifications and carry the ATEX Notify Body
number 0344.
Maximum Working Pressure
84CF Flanged Body Flowmeters
For specific temperature/pressure ratings for different materials and flanges, see MI 019-222.
31
MI 019-179 – May 2015
4. 84C Series Vortex Flowmeters
Flowmeter Materials
Flowmeter Body
The flowmeter body materials for the 84C Series Vortex Flowmeter are the same as the 84 Series
(Style B). See “Flowmeter Body (Style B)” on page 28.
Sensor Material, Fill Fluid, and Temperature Range
The sensor diaphragm material, fill fluid, and temperature range for the 84CF Flowmeters are
found within the model number on the data label as follows:
84CF020-TPRF1STDTJCA-CL
DIAPHRAGM MATERIAL, FILL FLUID, AND TEMPERATURE RANGE
Table 8. Material, Fill Fluid, and Temperature Range
Code
Diaphragm Material
Fill Fluid
Temperature Range
D
Nickel alloy CW2M (a)
Fluorolube
0 to 200°F (-20 to +90°C)
F
Stainless Steel CF3M
Fluorolube
0 to 200°F (-20 to +90°C)
R
Nickel alloy CW2M (a)
Silicone
0 to 400°F (-20 to +200°C)
S
Stainless Steel Type CF3M
Silicone
0 to 400°F (-20 to +200°C)
A (b)
Nickel alloy CW2M (a)
Unfilled
300° to 700°F (150° to 370°C)
B (b)
Stainless Steel Type CF3M
Unfilled
300° to 700°F (150° to 370°C)
a. Equivalent to Hastelloy® C-4C.
b. Not available with Body and Flange Material selection D.
NOTE
The temperature compensated Multi-Variable option -T allows for up to 500°F
(260°C). The temperature element of the RTD is rated up to 500°F (260°C). The
rating for the high temperature Vortex sensor is reduced from 700°F (370°C) to
500°F (260°C) when used with this option.
Sensor Replacement
! CAUTION
For ATEX or IECEx certified flameproof units, take special care not to scar, mar, ding,
or dent the surface of the sensor stem during assembly. This is critical to the integrity
of the flameproof surface finish.
! WARNING
To prevent injury from escaping process fluids, to maintain agency certification of this
product, and to prove the integrity of the parts and workmanship in containing
process pressure, a hydrostatic pressure test must be performed after the sensor
replacement is complete. The flowmeter must hold the appropriate pressure from
Table 9 for one minute (10 minutes to meet PED requirements) without leaking.
32
4. 84C Series Vortex Flowmeters
MI 019-179 – May 2015
It is important that the correct sensor replacement kits are used for 84C and for ATEX
applications per MI 019-223.
Table 9. Maximum Test Pressure
Test Pressure
End Connection
316 SS
(1.5X MWP)
Duplex SS, Nickel alloy
CW2M (a) (1.5X MWP)
ANSI Class 150
413 psi
435 psi
ANSI Class 300
1080 psi
1125 psi
ANSI Class 600
2160 psi
2250 psi
ANSI Class 900
3240 psi
3375 psi
ANSI Class 1500
5400 psi
5625 psi
PN 16
2.4 Mpa
2.4 Mpa
PN 25
3.8Mpa
3.8Mpa
PN 40
6.0 Mpa
6.0 Mpa
PN 63
9.5 Mpa
9.5 Mpa
PN 100
15.0 Mpa
15.0 Mpa
PN 160
24.0 Mpa
24.0 Mpa
a. Equivalent to Hastelloy® C-4C.
33
MI 019-179 – May 2015
34
4. 84C Series Vortex Flowmeters
5. Mass Flow Products
CFS10 and CFS20 Mass Flowtubes
Flowtube Identification: CFS10/CFS20 Connected to
CFT51
Refer to the data plate to determine the maximum pressure and temperature limits.
Electrical Certification Rating
Electrical certification information is printed on the agency plate (located above the data plate).
The electrical design safety code is also printed on the data plate as part of the model number.
The location of the code within the model number is shown below. See Table 10 for additional
information.
CFS10-05SCAAA
ELECTRICAL SAFETY CODE
Table 10. CFS10, CFS20 Electrical Safety Specification When Used with CFT51
Testing Laboratory, Type of Protection, and Area
Classification
Application Conditions (a)
Electrical
Safety Code
CSA/CSAus Division 1/Zone 0 Intrinsically Safe
Connected to CFT51 Electrical Safety
Code CDA and CNA
CAA
CSA/CSAus Division 2/Zone 2 Non-Incendive
Connected to CFT51 Electrical Safety
Code CDN and CNN
CCN
FM Division 1/Zone 0 Intrinsically Safe
Connected to CFT51 Electrical Safety
Code FDA and FNA
FAA
FM Division 2/Zone 2 Non-Incendive
Connected to CFT51 Electrical Safety
Code FDN and FNN
FFN
ATEX Intrinsic safe Ex ia/ic
Connected to CFT51 Electrical Safety
Code ADA and ANA
AAA
ATEX Non Sparking Zone 2 Ex nA
Connected to CFT51 Electrical Safety
Code ADN and ANN
ANN
IECEx Intrinsic safe Ex ia/ic
Connected to CFT51 Electrical Safety
Code EDA and ENA
EAA
IECEx Non Sparking Zone 2 Ex nA
Connected to CFT51 Electrical Safety
Code EDN and ENN
ENN
Agency approvals or certifications not required
YYY
a. Temperature Class is a function of process temperature. See Table 11.
NOTE
These flowtubes have been designed to meet the electrical safety descriptions listed in
the table above. For detailed information, or status of testing laboratory
approvals/certifications, contact Global Customer Support.
35
MI 019-179 – May 2015
5. Mass Flow Products
Table 11. Process Temperature Range for Electrical Safety Design Codes When Used with CFT51
Flowtube Size
Flowtube
Model
mm
in
Ambient Temperature
°C
°F
Process Temperature Range
Temp.
Class
°C
°F
Process Temperature Range for Intrinsically Safe Electrical Safety Design Codes (CAA, FAA, AAA, EAA)
CFS10
CFS20
3
through
20
0.125
through
0.750
25
through
50
1.00
through
2.00
40
and
80
1.50
and
3.00
–40 to +60°
–40 to +140°
T4
–200 to +180°
–328 to +356°
–55 to +180°
–67 to +356°
–55 to +180°
–67 to +356°
Process Temperature Range for Electrical Safety Design Codes for Zone 2 or Division 2 (CCN, FFN, ANN, ENN)
CFS10 and
CFS20
All Flowtube Sizes
–40 to +60°
–40 to +140°
T4
–40 to +180°
–40 to +356°
Process Temperature Range for Electrical Safety Design Code YYY (Agency Approvals Not Required)
CFS10 and
CFS20
All Flowtube Sizes
–40 to +180°
–40 to +356°
N/A
–40 to +180°
–40 to +356°
NOTE
Protect the equipment from the temperature of the process such that the ambient
temperature does not exceed 60°C (140°F).
Process Wetted Parts
The flowtube wetted material is found within the model number on the data label as follows:
CFS10-02SAAAA
FLOWTUBE WETTED MATERIAL
Code
Wetted Material
S
316L Stainless Steel
H
Nickel alloy CX2MW (a)
C
316L Stainless Steel (as prepared for Sanitary Applications, 3-A
Authorization No. 224
a. Equivalent to Hastelloy® C-22.
PED Compliance
The CFS10 and CFS20 Series Mass Flowtubes are fully compliant with the European Pressure
Equipment Directive as process piping devices for Fluid Groups 1 and 2 for Gas and Liquid
applications. The product data plate is marked accordingly for the line sizes and pressure ratings
for the above fluid groups. Contact Global Customer Support for the specific product category
classification for any given line size and pressure rating.
Line sizes and pressure ratings that are categorized as Category II or III carry the notifying body
(DNV) number 0575 under the CE mark. The PED compliance marking is affixed only to
products that have the ATEX electrical safety certifications and carry the ATEX Notify Body
number 0344.
36
5. Mass Flow Products
MI 019-179 – May 2015
Maximum Working Pressure
Maximum process pressure is dependent on the process temperature, flowtube size, and end
connections used. The following tables specify the maximum process pressure for either the type
of end connection (Table 12) or process temperature (Table 13). Interpolation is required for
process temperatures between those listed. Use the lesser of the pressures determined from these
tables.
Table 12. End Connection Process Temperature/Pressure Limits (a)
MWP
Process
Temp.
316/316L ss
Nickel alloy CX2MW (c)
ANSI Class 150 Flange
100°F
200°F
300°F
356°F
275 psig
240 psig
215 psig
204 psig
290 psig
260 psig
230 psig
213 psig
ANSI Class 300 Flange
100°F
200°F
300°F
356°F
720 psig
620 psig
560 psig
535 psig
750 psig
750 psig
730 psig
713 psig
ANSI Class 600 Flange
100°F
200°F
300°F
356°F
1440 psig
1240 psig
1120 psig
1067 psig
1500 psig
1500 psig
1455 psig
1421 psig
EN 1092
PN 10/16 Flange
RT (d)
100°C
150°C
180°C
16.0 bar
16.0 bar
14.5 bar
13.8 bar
16.0 bar
16.0 bar
14.5 bar
13.8 bar
EN 1092
PN 25/40 Flange
RT (d)
100°C
150°C
180°C
40.0 bar
40.0 bar
36.3 bar
34.7 bar
40.0 bar
40.0 bar
36.3 bar
34.7 bar
EN 1092
PN 100 Flange
RT (d)
100°C
150°C
180°C
100 bar
100 bar
90.9 bar
86.9 bar
100 bar
100 bar
90.9 bar
86.9 bar
End Connection Type (b)
Threaded, NPT, ANSI B2.1
MWP limited by threaded end connection limits per Table 13.
Quick Disconnect Sanitary Coupling
or DIN 11851 Coupling
Maximum working pressure is 10 bar at 25°C (145 psig at 77°F). (e)
a. Linear interpolation is acceptable.
b. See model codes for flowtube configurations available with 316 ss, 316L ss, and nickel alloy CX2MW (equivalent to
Hastelloy® C-22) end connections.
c. Equivalent to Hastelloy® C-22.
d. RT = Reference Temperature = -10 to +100°C.
e. If higher MWPs are required, contact Global Customer Support.
37
MI 019-179 – May 2015
5. Mass Flow Products
Table 13. Flowtube Process Temperature/Pressure Limits - Threaded End Connections (a)
Nominal
Flowtube Size
mm
3 and 6
15 and 20
Maximum Working Pressure (MWP) (a)
Process
Temperature
316/316L ss
Nickel alloy CX2MW (b)
in
°C
°F
bar
psig
bar
psig
1/8 and 1/4
40
100
150
180
100
200
300
356
179
155
140
133
2600
2243
2026
1932
217
217
213
207
3150
3150
3050
3010
1/2 and 3/4
40
100
150
180
100
200
300
356
100
85
78
75
1440
1240
1120
1080
103
103
100
98
1500
1500
1455
1435
a. Linear interpolation is acceptable.
b. Equivalent to Hastelloy® C-22.
CFS25 Mass Flowtubes
Flowtube Identification: CFS25 Connected to CFT51
Refer to the data plate to determine the maximum pressure and temperature limits.
Electrical Certification Rating
Electrical certification information is printed on the agency plate (located above the data plate).
The electrical design safety code is also printed on the data plate as part of the model code. The
location of the safety code within the model code is shown below. See Table 14 for additional
information.
CFS25-028KHAFHSACAA-A
ELECTRICAL SAFETY CODE
Table 14. CFS25 Electrical Safety Specification When Used with CFT51 (a)
Testing Laboratory,
Type of Protection, and
Area Classification
Application Conditions (b)
Electrical
Safety Design
Code
CSA/CSAus Intrinsically Safe Class I, Temperature Class T4 Ta = -40°C to +70°C
Division 1/Zone 0, Groups C, D
Connected to CFT51 Electrical Safety Code CDA or CNA
CAA
ATEX Intrinsically Safe Ex ia/ic,
Group IIB
Temperature Class T4 Ta = -40°C to +70°C
Connected to CFT51 Electrical Safety Code ADA or ANA
AAA
IECEx Intrinsically Safe Ex ia/ic,
Group IIB
Temperature Class T4 Ta = -40°C to +70°C
Connected to CFT51 Electrical Safety Code EDA or ENA
EAA
No electrical certification
a. These flowtubes have been designed to meet the electrical safety descriptions listed in the table above. For detailed
information, or status of testing laboratory approvals and certifications, contact Global Customer Support.
b. Process temperature range is -100°C to +70°C.
38
YYY
5. Mass Flow Products
MI 019-179 – May 2015
Process Wetted Parts
The flowtube wetted material is found within the model number on the data label as follows:
CFS25-028KHABHSACAA-AW
FLOWTUBE WETTED MATERIAL
Code
Wetted Material
S
316L Stainless Steel
H
Nickel alloy (a)
a. Equivalent to Hastelloy® C-22.
PED Compliance
CFS25 Mass Flowtubes are fully compliant with the European Pressure Equipment Directive as
process piping devices for Fluid Groups 1 and 2 for Gas and Liquid applications. The product
data plate is marked accordingly for the line sizes and pressure ratings for the above fluid groups.
Contact Global Customer Support for the specific product category classification for any given
line size and pressure rating.
Line sizes and pressure ratings that are categorized as Category II or III carry the notifying body
number 0036 (TÜV SÜD Industrie Service) under the CE mark. The PED compliance marking
is affixed only to products that have the ATEX electrical safety certifications and carry the ATEX
Notify Body number 0123 (TÜV SÜD).
Maximum Working Pressure
Table 15. Flowtube Process Pressure Rating (a)
Maximum Working Pressure (MWP)
Model CFS25
bar
psi
-0325
200
2,900
-0650
200
2,900
-1550
200
2,900
-3100
200
2,900
-5500
345
5,000
-7900
100
1,450
-028K
100
1,450
-065K
100
1,450
a. Pressure ratings are for flowtubes only. End connections
may limit the pressure rating.
39
MI 019-179 – May 2015
5. Mass Flow Products
CFT51 Mass Flow Transmitters
Refer to the data plate to determine the electrical certification rating, origin code, input supply
voltage, input power, and ambient temperature limit.
Electrical Certification Rating
The electrical safety code is printed on the data plate as part of the model number. The location of
the code within the model number is shown below. See Table 16 for additional information.
CFT51-TB1EABANNANN
ELECTRICAL SAFETY CODE
Table 16. CFT51 Electrical Safety Specifications
Types of Protection
and Area Classification
Application Conditions
Electrical
Safety
Design Code
ATEX, II 2 (1) G Ex d [ia IIB Ga] IIC T6 Gb
Flameproof enclosure with Intrinsic safe
sensor outputs. Temperature Class T6.
Ta = -40°C to +60°C.
ADA
ATEX, II 2 (3) G Ex d [ic IIB Gc] IIC T6 Gb
Flameproof enclosure with Energy Limited or
intrinsic safe zone 2 sensor outputs.
Temperature Class T6. Ta = -40°C to +60°C.
ADN
(a)
ATEX, II 3 (1) G Ex nA [ia IIB Ga] IIC T4 Gc
Non-sparking enclosure with Intrinsic safe
sensor Temperature Class T4.
Ta = -40°C to +60°C.
ANA
ATEX, II 3 G Ex nA IIC T4 Gc
Non-sparking
Temperature Class T4. Ta = -40°C to +60°C
ANN
(a)
CSA/CSAus XP Class I, Division 1, Groups A, B, C, and
D; Class II, Division 1, Groups E, F, and G; Class III,
Division 1;
AIS Class I, Division 1, Groups A, B, C, and D;
Ex d IIC [ia] IIB; AEx d IIC [ia] IIB
Explosionproof and Flameproof enclosure
with intrinsically safe outputs
Temperature Class T6. Ta = -40°C to +60°C
Temperature Class T4. Ta = -40°C to +60°C
CDA
CSA/CSAus XP Class I, Division 1, Groups A, B, C, and
D; Class II, Division 1, Groups E, F, and G; Class III,
Division 1;
ANI Class I, Division 2, Groups A, B, C, and D;
Ex d [nL] IIC; AEx d [nC] IIC
Explosionproof and Flameproof enclosure
with Non-Incendive outputs
Temperature Class T6. Ta = -40°C to +60°C
Temperature Class T4. Ta = -40°C to +60°C
CDN
(a)
CSA/CSAus NI Class I, Division 2, Groups A, B, C, and Non-incendive enclosure with intrinsically
safe outputs
D; also intrinsically safe for AIS Class I, Division 1,
Temperature Class T4. Ta = -40°C to +60°C
Groups A, B, C, and D; AEx nA IIC [ia] IIB;
Ex nA IIC [ia] IIB
CNA
CSA/CSAus NI Class I, Division 2, Groups A, B, C, and Non-incendive and Non-sparking
D; also nonincendive for ANI Class I, Division 2, Groups Temperature Class T4. Ta = -40°C to +60°C
A, B, C, and D; AEx nA [nL] IIC; Ex nA [nC] IIC
CNN
(a)
FM XP Class I, Division 1, Groups A, B, C, and D; Class
II, Division 1, Groups E, F, and G; Class III, Division 1;
AIS Class I, Division 1, Groups A, B, C, and D.
AEx d IIB [ia] IIC
Explosionproof and Flameproof enclosure
with intrinsically safe outputs
Temperature Class T6. Ta = -40°C to +60°C
Temperature Class T4. Ta = -40°C to +60°C
FDA
(a)
FM XP Class I, Division 1, Groups A, B, C, and D; Class
II, Division 1, Groups E, F, and G; Class III, Division 1;
ANI Class I, Division 2, Groups A, B, C, and D.
AEx d [nC] IIC
Explosionproof and Flameproof enclosure
with Non-Incendive outputs
Temperature Class T6. Ta = -40°C to +60°C
Temperature Class T4. Ta = -40°C to +60°C
FDN
(a)
FM NI Class I, Division 2, Groups A, B, C, and D;
AIS Class I, Division 1, Groups A, B, C, and D
AEx nA IIC [ia] IIB
Non-incendive enclosure with intrinsically
safe outputs
Temperature Class T4. Ta = -40°C to +60°C
FNA
(a)
40
5. Mass Flow Products
MI 019-179 – May 2015
Table 16. CFT51 Electrical Safety Specifications (Continued)
Application Conditions
Electrical
Safety
Design Code
FM NI Class I, Division 2, Groups A, B, C, and D;
ANI Class I, Division 2, Groups A, B, C, and D
AEx nA IIC
Non-Incendive
Temperature Class T4. Ta = -40°C to +60°C
FNN
(a)
IECEx, Ex d [ia IIB Ga] IIC T6 Gb
Flameproof enclosure with Intrinsic safe
sensor outputs. Temperature Class T6
Ta = -40°C to +60°C
EDA
IECEx, Ex d [ic IIB Gc] IIC T6 Gb
Flameproof enclosure with Energy Limited or
intrinsic safe zone 2 sensor outputs
Temperature Class T6. Ta = -40°C to +60°C
EDN
(a)
IECEx, Ex nA [ia IIB Ga] IIC T4 Gc
Non-sparking enclosure with Intrinsic safe
sensor. Temperature Class T4
Ta = -40°C to +60°C
ENA
IECEx, Ex nA IIC T4 Gc
Non-sparking
Temperature Class T4. Ta = -40°C to +60°C
ENN
(a)
No Certifications
Not Applicable
ZZZ
Types of Protection
and Area Classification
a. Not available with CFS25 flowtube.
NOTE
These transmitters have been designed to meet the electrical safety descriptions listed
in Table 16. For detailed information, or status of testing laboratory
approvals/certifications, contact Global Customer Support.
ATEX Warnings
! WARNING
1. Ensure area is known to be nonhazardous before removing cover.
2. Do not open while circuits are live.
3. Do not open when energized or when an explosive atmosphere may be present.
4. Explosion Hazard: Substitution of components may impair intrinsic safety or
Division 2 approvals.
5. Explosion Hazard: Do not disconnect equipment unless power has been turned off
or the area is known to be nonhazardous.
6. The cable or conduit entries and the closing elements of unused openings shall be
suitable for the type of protection, as applied and correctly installed.
7. The field wiring must be separately installed and protected against mechanical
damage.
41
MI 019-179 – May 2015
5. Mass Flow Products
For Explosionproof Certifications:
! WARNING
1. Keep cover tight while circuits are live unless area is known to be nonhazardous.
2. To prevent ignition of flammable or combustible atmospheres, disconnect power
before servicing.
3. The CFS10, CFS20, and CFS25 flowtube junction boxes contain more than
10% aluminum and are considered to constitute a potential risk of ignition by
impact or friction. Care must be taken to prevent impact and friction when
installing or using the junction box in a Zone 0 installation.
! CAUTION
The CFT51 transmitter is to be used only with Foxboro CFS flowtubes in accordance
with the ATEX and IECEx certificates.
ATEX Compliance Documents
EN 60079-1:2007
EN 60079-26:2007
EN 60079-31:2008
EN 60079-15:2005
EN 60079-11:2007
IEC 60079-0:2006
IECEx Compliance Documents
IEC 60079-0:2004 Ed 4.0
IEC 60079-26:2006 Ed 2
IEC 60079-1:2007 Ed 6
IEC 60079-31:2008 Ed 1
IEC 60079-11:2006 Ed 5
Operating Temperature Limits
The operating temperature limits of the electronics are -40 and +60°C (-40 and +140°F). Ensure
that the transmitter is operated within this range.
42
5. Mass Flow Products
MI 019-179 – May 2015
Connection Diagrams
Figure 10. Flowtube in Zone 0 and Transmitter in Zone 2 Area
ATEX/IECEx Approvals
CFT51 Transmitter in Zone 2 Area with
CFS Series Flowtube in Zone 0 Area
Unclassified Locations
(Non Hazardous Locations)
Customer Supplied
USER I/O
Power Supply
AC Version: 120/240 VAC
DC Version: 36 VDC
(4-20 mA, Pulse, Contact Input,
Contact Output, and Comms)
CFT51 Transmitter
Non Sparking
Zone 2 Ex nA IIC
Classified Locations
(Hazardous Locations)
CO
PO CO CO
CI
17 16 15 14 13 12 11 10 9
8
Conduit or Other Code
Approved Zone 2
PO CO COMMS
L
N
7
1
2
6
5
4
3
2
1
Transmitter
Model Code:
CFT51*********ANA
CFT51*********ENA
1
2
3
4
5
6
7
8
Intrinsically Safe Flowtube/Transmitter
Cable Must Be Twisted Shielded Pairs
Connection Length Up To
1000 Feet for CFS10 or CFS20
Up To 100 Feet for CFS25
Connect Flowtube Cable to CFT51
and Flowtube per MI 019-140
and MI 019-120 or MI 019-125
Classified Locations
(Hazardous Locations)
CFS Series Flowtubes
Zone 0 Ex ia IIB
1
2
9 10 11 12
3
4
5
6
7
8
9 10 11 12
Flowtube Model Code:
CFS10-****AAA
CFS10-****EAA
CFS20-****AAA
CFS20-****EAA
CFS25-**********AAA
CFS25-**********EAA
43
MI 019-179 – May 2015
5. Mass Flow Products
Figure 11. Flowtube and Transmitter Located in Zone 2 Area
ATEX/IECEx Approvals
CFT51 Transmitter and CFS Series Flowtube in Zone 2 Area
Unclassified Locations
(Non Hazardous Locations)
USER I/O
Customer Supplied
(4-20 mA, Pulse, Contact Input,
Contact Output, and Comms)
Power Supply
AC Version: 120/240 VAC
DC Version: 36 VDC
Classified Locations
(Hazardous Locations)
CO
PO CO CO
CI
17 16 15 14 13 12 11 10 9
8
Conduit or Other Code
Approved Zone 2
PO CO COMMS
L
N
7
1
2
6
5
4
3
2
1
Transmitter
Model Code:
CFT51*********ANN
CFT51*********ENN
1
2
3
4
5
6
7
8
9 10 11 12
CFT51 Transmitter and
CFS Flowtubes
Non Sparking
Class I Zone 2 Ex nA [nL] IIC
Class I Zone 2 AEx nA [nC] IIC
Conduit or Other Code
Approved Zone 2
Maximum Wiring
Length 1000 Foot
Cable Must Be Twisted
Shielded Pairs
1
Connect Flowtube Cable
to CFT51 and Flowtube
per MI 019-140 and
MI 019-120
44
2
3
4
5
6
7
8
9 10 11 12
Flowtube Model Code:
CFS10-****ANN
CFS10-****ENN
CFS20-****ANN
CFS20-****ENN
5. Mass Flow Products
MI 019-179 – May 2015
Figure 12. Flowtube in Zone 0 and Transmitter in Zone 1 (Flameproof) Area
ATEX/IECEx Approvals
CFT51 Transmitter in Zone 1 (Flameproof) Area with
CFS Series Flowtube in Zone 0 Area
Unclassified Locations
(Non Hazardous Locations)
USER I/O
Customer Supplied
(4-20 mA, Pulse, Contact Input,
Contact Output, and Comms)
Power Supply
AC Version: 120/240 VAC
DC Version: 36 VDC
CFT51 Transmitter
Flameproof
Class I Zone 1 Ex d IIC
Classified Locations
(Hazardous Locations)
CO
PO CO
CO
CI
17 16 15 14 13 12 11 10 9
8
Conduit or Other Code
Approved Zone 1
PO CO COMMS
L
N
7
1
2
6
5
4
3
2
1
Transmitter
Model Code:
CFT51*********ADA
CFT51*********EDA
1
2
3
4
5
6
7
8
Intrinsically Safe Flowtube/Transmitter
Cable Must Be Twisted Shielded Pairs
Connection Length Up To
1000 Feet for CFS10 or CFS20
Up To 100 Feet for CFS25
Connect Flowtube Cable to CFT51
and Flowtube per MI 019-140
and MI 019-120 or MI 019-125
Classified Locations
(Hazardous Locations)
CFS Series Flowtubes
Zone 0 Ex ia IIB
1
9 10 11 12
2
3
4
5
6
7
8
9 10 11 12
Flowtube Model Code:
CFS10-****AAA
CFS10-****EAA
CFS20-****AAA
CFS20-****EAA
CFS25-**********AAA
CFS25-**********EAA
45
MI 019-179 – May 2015
46
5. Mass Flow Products
6. Magnetic Flow Products
8000A Magnetic Flowtubes
PED Compliance
The 8000A Series Magnetic Flowtubes are fully compliant with the European Pressure
Equipment Directive as process piping devices for Fluid Group 2 liquids only. the resulting
product category classifications are either SEP or Category I, depending on line size and pressure
rating, and as such, the product data labels carry the CE mark only (with no notifying body
number).
Refer to the data plate to determine the model code, origin code, electrode material, and
maximum working pressures at specified temperatures.
Process Pressure and Temperature Limits
Process pressure and temperature limits are dependent on the lining material.
The lining material code is printed on the data plate as part of the model number. The location of
the code within the model number is shown below:
LINING MATERIAL
C = Ceramic
P = pfa
8002A-WP-PJG
LINING MATERIAL
Table 17. Process Pressure and Temperature Limits: Wafer Body Flowtubes with Ceramic Lining
Flowtube Model
Code
Operating Condition Limits
Remotely Mounted Transmitter
Integrally Mounted Transmitter
801SA-WC
through
8002A-WC
Full Vacuum and:
5.1 MPa at 38°C (740 psi at 100°F)
and
4.4 MPa at 204°C (635 psi at 400°F)
Full Vacuum and:
5.1 MPa at 38°C (740 psi at 100°F)
and
4.7 MPa at 121°C (665 psi at 250°F)
8003A-WC
through
8006A-WC
Full Vacuum and:
4.6 MPa at 38°C (675 psi at 100°F)
and
4.0 MPa at 204°C (580 psi at 400°F)
Full Vacuum and:
4.6 MPa at 38°C (675 psi at 100°F)
and
4.3 MPa at 121°C (580 psi at 250°F)
47
MI 019-179 – May 2015
6. Magnetic Flow Products
Table 18. Process Pressure and Temperature Limits: Wafer Body Flowtubes with PFA Lining
Flowtube Model
Code
Operating Condition Limits
Remotely Mounted Transmitter
800HA-WP through Full Vacuum and:
8006A-WP
5.1 MPa at 38°C (740 psi at 100°F)
and
4.4 MPa at 180°C (635 psi at 356°F)
Integrally mounted Transmitter
Full Vacuum and:
5.1 MPa at 38°C (740 psi at 100°F)
and
4.7 MPa at 121°C (665 psi at 250°F)
Process Wetted Parts
The process wetted parts are the flowtube lining, the electrodes, and the gaskets. The lining
material code is printed on the data plate as part of the model number (as shown above), the
electrode material is shown on the data plate, and the gaskets are supplied by the user.
9300A Magnetic Flowtubes
PED Compliance
The 9300A Series Magnetic Flowtubes are fully compliant with the European Pressure
Equipment Directive as process piping devices for Fluid Group 2 liquids only. the resulting
product category classifications are either SEP or Category I, depending on line size and pressure
rating, and as such, the product data labels carry the CE mark only (with no notifying body
number).
Refer to the data plate to determine the model code, origin code, electrode material, and
maximum working pressures at specified temperatures.
Pressure and Temperature Limits
See Tables 19 through 24 for ambient temperature and process pressure/temperature limits of
flowtubes with various linings.
See Table 25 for process/temperature limits of flowtubes with various end connections.
The process temperature limits are dependent on the line size and lining material.
The line size and lining material codes are printed on the data plate as part of the model number.
The location of the codes within the model number is shown below:
9303A-SIBA-PBJ-GM
LINING MATERIAL
LINE SIZE
48
LINE SIZE
03 = 3 in
04 = 4 in
06 = 6 in
LINING MATERIAL
P = PFA
T = PTFE
6. Magnetic Flow Products
MI 019-179 – May 2015
Table 19. Transmitter Remote Mounted PFA-Lined Flowtubes
Influence
Ambient Temperature
Process Temperature
1 to 6 in
8 to 12 in
Process Pressure
1 to 6 in
8 to 12 in
Normal Operating Conditions
-40 to +70°C
-40 to +158°F
-40 to +180°C
-40 to +356°F
-40 to +120°C
-40 to +250°F
Full Vacuum to 5.1 MPa at 38°C (740 psi
at 100°F)
Full Vacuum to 4.4 MPa at 180°C (645 psi
at 356°F)
Full Vacuum to 5.1 MPa at 38°C (740 psi
at 100°F
Full Vacuum to 4.7 MPa at 120°C (665 psi
at 250°F)
Table 20. Transmitter Remote Mounted PTFE-Lined Flowtubes
Influence
Normal Operating Conditions
Ambient Temperature -40 to +70°C
-40 to +158°F
Process Temperature -40 to +180°C
-40 to +356°F
Process Pressure
No vacuum to 2.0 MPa at 38°C (285 psi
at 100°F)
No vacuum to 1.5 MPa at 180°C (213
psi at 356°F)
Table 21. Transmitter Remote Mounted Polyurethane-Lined Flowtubes
Influence
Normal Operating Conditions
Ambient
Temperature
-29 to +70°C
-20 to +158°F
Process
Temperature
-29 to +71°C
-20 to +160°F
Process Pressure
Full vacuum to 2.0 MPa at 38°C (285 psi
at 100°F)
Full vacuum to 1.9 MPa at 71°C (270 psi
at 160°F)
49
MI 019-179 – May 2015
6. Magnetic Flow Products
Table 22. Transmitter Integrally Mounted PFA-Lined Flowtubes
Influence
Normal Operating Conditions
Ambient
Temperature
-20 to +55°C
-4 to +131°F
Process
Temperature
-40 to +120°C
-40 to +250°F
Process Pressure
Full vacuum to 5.1 MPa at 38°C (740 psi
at 100°F)
Full vacuum to 4.7 MPa at 120°C (665
psi at 250°F)
Table 23. Transmitter Integrally Mounted PTFE-Lined Flowtubes
Influence
Normal Operating Conditions
Ambient
Temperature
-20 to +55°C
-4 to +131°F
Process
Temperature
-40 to +120°C
-40 to +250°F
Process Pressure
No vacuum to 2.0 MPa at 38°C (285 psi
at 100°F)
No vacuum to 1.7 MPa at 120°C (245
psi at 250°F)
Table 24. Transmitter Integrally Mounted Polyurethane-Lined Flowtubes
Influence
Normal Operating Conditions
Ambient
Temperature
-20 to +55°C
-4 to +131°F
Process
Temperature
-20 to +71°C
-4 to +160°F
Process Pressure
Full Vacuum to 2.0 MPa at 38°C (285
psi at 100°F)
Full Vacuum to 1.9 MPa at 71°C (270
psi at 160°F)
50
6. Magnetic Flow Products
MI 019-179 – May 2015
Table 25. Flange Pressure-Temperature Limits for PFA-Lined/PTFE-lined Flowtubes
Maximum Permissible Operating Pressure at Temperature Listed
Carbon Steel
(ASME/ANSI Group No. 1.1)
316 ss Stainless Steel
DIN Flange
Rating
–40°C
50°C
100°C
180°C
–40°C
50°C
100°C
180°C
PN 10
9.0 bar
9.0 bar
7.8 bar
7.1 bar
10.0 bar
10.0 bar
10.0 bar
8.4 bar
PN 16
14.2 bar
14.2 bar
12.5 bar
11.5 bar
16 bar
16 bar
16 bar
15.3 bar
PN 25
22.36 bar
22.3 bar
19.5 bar
17.9 bar
25.0 bar
25.0 bar
25.0 bar
20.2 bar
PN 40
37.4 bar
37.4 bar
31.2 bar
28.6 bar
40 bar
40 bar
40 bar
38.3 bar
ANSI Flange
Rating
–40°F
100°F
200°F
356°F
–40°F
100°F
200°F
356°F
Class 150
275 psig
275 psig
240 psig
205 psig
285 psig
285 psig
260 psig
213 psig
Class 300
720 psig
720 psig
620 psig
538 psig
740 psig
740 psig
675 psig
644 psig
NOTE
For process temperatures >120°C (>250°F), the transmitter must be remotely
mounted.
Process Wetted Parts
The supplied process wetted parts are the flowtube lining and the electrodes. The electrode
material is printed on the data label. The lining material code is printed on the data plate as part
of the model number. The location of the code within the model number is shown below:
LINING MATERIAL
P = PFA
T = PTFE
9303A-SIBA-PBJ-GM
LINING MATERIAL
8300 Magnetic Flowtubes
PED Compliance
The 8300 Series Magnetic Flowtubes are fully compliant with the European Pressure Equipment
Directive as process piping devices for Fluid Group 2 liquids only. the resulting product category
classifications are either SEP or Category I, depending on line size and pressure rating, and as
such, the product data labels carry the CE mark only (with no notifying body number).
Refer to the data plate to determine the model code, origin code, electrode material, and
maximum working pressures at specified temperatures.
51
MI 019-179 – May 2015
6. Magnetic Flow Products
Ambient Temperature Limits
Normal Operating Condition Limits: -10 and +50°C (20 and 120°F)
Operative Limits: -30 and +60°C (-20 and +140°F)
Process Pressure and Temperature Limits
See Figure 13 and Tables 26, 27, and 28.
Figure 13. Process Pressure and Temperature Limits PTFE-Lined Flowtubes — 830H through 8312
Sizes Only
(See Table 26 for 8314 through 8324 Sizes)
Table 26. Process Pressure and Temperature Limits
PTFE-Lined Flowtubes — 8314 through 8324 Sizes Only
cf
Flange
Rating
ANSI
Class 150
Process Pressure Limits
Flowtube
Line Size
Lower Limit
Upper Limit
Process Temperature Limits
Lower Limit
Upper Limit
8314 and 8316
Zero (No Vacuum)
1.38 MPa (200 psig)
–18 °C (0 °F)
82 °C (180 °F)
8318 to 8324
Zero (No Vacuum)
1.03 MPa (150 psig)
–18 °C (0 °F)
82 °C (180 °F)
Metric PN 6
8314 to 8324
Zero (No Vacuum)
0.60 MPa (87 psig)
–18 °C (0 °F)
82 °C (180 °F)
Metric PN 10
8314 to 8324
Zero (No Vacuum)
1.00 MPa (145 psig)
–18 °C (0 °F)
82 °C (180 °F)
52
6. Magnetic Flow Products
MI 019-179 – May 2015
Table 27. Process Pressure and Temperature Limits
Polyurethane-Lined Flowtubes — 8302 through 8336 Sizes
Flange
Rating
ANSI Class 150
ANSI Class 300
Metric PN 10
Process Pressure Limits
Flowtube
Line Size
Lower Limit
Process Temperature Limits
Upper Limit
Lower Limit
8302 to 8312
Full Vacuum
1.65 MPa (240 psig)
–18 °C (0 °F)
Upper Limit
71 °C (160 °F)
8314 and 8316
Full Vacuum
1.38 MPa (200 psig)
–18 °C (0 °F)
71 °C (160 °F)
8316 to 8324
Full Vacuum
1.03 MPa (150 psig)
–18 °C (0 °F)
71 °C (160 °F)
8302 to 8304
Full Vacuum
4.83 MPa (700 psig)
–18 °C (0 °F)
71 °C (160 °F)
8306 and 8308
Full Vacuum
1.65 MPa (240 psig)
–18 °C (0 °F)
71 °C (160 °F)
8302 to 8324
Full Vacuum
1.00 MPa (145 psig)
–18 °C (0 °F)
71 °C (160 °F)
8330
Full Vacuum
0.69 MPa (100 psig)
–18 °C (0 °F)
71 °C (160 °F)
8336
Full Vacuum
0.62 MPa (90 psig)
–18 °C (0 °F)
71 °C (160 °F)
Metric PN 16
8302 to 8312
Full Vacuum
1.62 MPa (235 psig)
–18 °C (0 °F)
71 °C (160 °F)
Metric PN 25
8302 to 8304
Full Vacuum
2.50 MPa (362 psig)
–18 °C (0 °F)
71 °C (160 °F)
8306 to 8312
Full Vacuum
1.65 MPa (240 psig)
–18 °C (0 °F)
71 °C (160 °F)
8302 to 8304
Full Vacuum
4.00 MPa (580 psig)
–18 °C (0 °F)
71 °C (160 °F)
8306 to 8312
Full Vacuum
1.65 MPa (240 psig)
–18 °C (0 °F)
71 °C (160 °F)
Metric PN 6
8314 to 8336
Full Vacuum
0.60 MPa (87 psig)
–18 °C (0 °F)
71 °C (160 °F)
AWWA Class D
8330
Full Vacuum
0.69 MPa (100 psig)
–18 °C (0 °F)
71 °C (160 °F)
8336
Full Vacuum
0.62 MPa (90 psig)
–18 °C (0 °F)
71 °C (160 °F)
Metric PN 40
Table 28. Process Pressure and Temperature Limits
Neoprene-Lined Flowtubes — 8314 through 8336 Sizes
Flange
Rating
Process Pressure Limits
Flowtube
Line Size
Lower Limit
ANSI Class 150
2814 and 2816
Full Vacuum
2818 to 2824
Full Vacuum
AWWA Class D
2830
Full Vacuum
2836
Full Vacuum
Metric PN 6
2814 to 2836
Full Vacuum
Metric PN 10
2814 to 2824
Full Vacuum
2830
Full Vacuum
2836
Full Vacuum
Process Temperature Limits
Upper Limit
Lower Limit
Upper Limit
–18 °C (0 °F)
82 °C (180 °F)
1.03 MPa (150 psig)
–18 °C (0 °F)
82 °C (180 °F)
0.69 MPa (100 psig)
–18 °C (0 °F)
82 °C (180 °F)
0.62 MPa (90 psig)
–18 °C (0 °F)
82 °C (180 °F)
0.60 MPa (87 psig)
–18 °C (0 °F)
82 °C (180 °F)
1.00 MPa (145 psig)
–18 °C (0 °F)
82 °C (180 °F)
0.69 MPa (100 psig)
–18 °C (0 °F)
82 °C (180 °F)
0.62 MPa (90 psig)
–18 °C (0 °F)
82 °C (180 °F)
1.38 MPa (200 psig)
Process Wetted Parts
The supplied process wetted parts are the flowtube lining and the electrodes. The electrode
material is printed on the data label. The lining material code is printed on the data plate as part
of the model number. The location of the code within the model number is shown below:
8303-SAZD-ASJ-G
LINING MATERIAL
LINING MATERIAL
A = Polyurethane
N = Neoprene
T = ptfe
53
MI 019-179 – May 2015
6. Magnetic Flow Products
2800 Magnetic Flowtubes
PED Compliance
The 2800 Series Magnetic Flowtubes are fully compliant with the European Pressure Equipment
Directive as process piping devices for Fluid Group 2 liquids only. the resulting product category
classifications are either SEP or Category I, depending on line size and pressure rating, and as
such, the product data labels carry the CE mark only (with no notifying body number).
Refer to the data plate to determine the model code, origin code, electrode material, and
maximum working pressures at specified temperatures.
Ambient Temperature Limits
Normal Operating Condition Limits: -10 and +50°C (20 and 120°F)
Operative Limits: -30 and +60°C (-20 and +140°F)
NOTE
If an E96T Transmitter is integrally mounted to the flowtube, the maximum ambient
temperature is 38°C (100°F).
Process Pressure and Temperature Limits
Sizes 2.5 through 300 mm (1/10 through 12 in)
See Figure 14 and Table 29.
54
6. Magnetic Flow Products
MI 019-179 – May 2015
Figure 14. Process Temperature and Pressure Limits for Flowtubes with PFA or PTFE Lining.
B
A
A
E
E
1.4
D
200
D
PROCESS PRESSURE, MPa
PROCESS PRESSURE, psig
B
1.6
250
F
H
150
J
C
K
100
50
L
0
FOR
2891 AND
2893 ONLY
FULL
VACUUM
0
FOR
2891 THROUGH
2804 TUBES ONLY
80
160
240
320
PROCESS TEMPERATURE, ˚F
H
1.0
J
0.8
C
K
0.6
0.4
0.2
L
M
FOR
2891 AND
2893 ONLY
FULL
VACUUM
400
F
1.2
-20
0
FOR
2891 THROUGH
2804 TUBES ONLY
40
80
120
160
PROCESS TEMPERATURE, ˚C
M
200
NOTES
1. Process pressure and temperature must be within the following regions:
– Region bounded by curve LABCM for flowtubes with ANSI Class 150 or 300 flanges
– Region bounded by curve LHJKM for flowtubes with PN 10 flanges
– Region bounded by curve LDEFM for flowtubes with PN 16, 25, or 40 flanges
2. Contact Global Customer Support for applications involving elevated pressure.
Table 29. Process Temperature and Pressure Limits for Polyurethane Lining
Pressure Limits
Flange
Model Code
Series
Upper Limits
MPa
psi
bar or kg/cm2
ANSI Class 150
2802 to 2812
1.7
240
17
ANSi Class 300
2802 to 2804
2806 and 2808
4.8
1.7
700
240
48
17
PN10
2802 to 2812
1.0
145
10
PN 16
2802 to 2812
1.6
232
16
PN 25
2802 to 2804
2806 to 2812
2.5
1.7
362
240
25
17
PN 40
2802 to 2804
2806 to 2812
4.0
1.7
590
240
40
17
Temperature Limits
Lower
Limit
Full
Vacuum
Lower
Limit
-18°C
(0°F)
Upper
Limit
+71°C
(+160°F)
55
MI 019-179 – May 2015
6. Magnetic Flow Products
Sizes 350 through 900 mm (14 through 36 in)
Table 30. Process Pressure and Temperature Limits - ptfe-Lined Flowtubes (2814 - 2824 Sizes Only)
Flange
Rating
Process Pressure Limits
Flowtube Model
(Line Size)
Lower Limit
Upper Limit
ANSI
Class 150
2814 and 2816
Zero (No Vacuum)
1.38 MPa (200 psig)
2818 to 2824
Zero (No Vacuum)
1.03 MPa (150 psig)
Metric PN 6
2814 to 2824
Zero (No Vacuum)
0.60 MPa (87 psig)
Metric PN 10
2814 to 2824
Zero (No Vacuum)
1.00 MPa (145 psig)
Process Temperature Limits
Lower Limit
-18°C (0°F)
Upper Limit
82°C (180°F)
Table 31. Process Pressure and Temperature Limits - Polyurethane-Lined Flowtubes
Flange
Rating
ANSI Class 150
Metric PN 10
Flowtube
Line Size
Process Pressure Limits
Lower Limit
Upper Limit
2814 and 2816
Full Vacuum
1.38 MPa (200 psig)
2816 to 2824
Full Vacuum
1.03 MPa (150 psig)
2814 to 2824
Full Vacuum
1.00 MPa (114 psig)
2830
Full Vacuum
0.69 MPa (100 psig)
2836
Full Vacuum
0.62 MPa (90 psig)
Metric PN 6
2814 to 2824
Full Vacuum
0.60 MPa (87 psig)
AWWA Class D
2830
Full Vacuum
0.69 MPa (100 psig)
2836
Full Vacuum
0.62 MPa (90 psig)
Process Temperature Limits
Lower Limit
-18°C (0°F)
Upper Limit
71°C (160°F)
Table 32. Process Pressure and Temperature Limits - Neoprene-Lined Flowtubes
Flange
Rating
Flowtube Model
(Line Size)
Process Pressure Limits
Lower Limit
ANSI
Class 150
2814 and 2816
2818 to 2824
Full Vacuum
1.03 MPa (150 psig)
AWWA Class D
2830
Full Vacuum
0.69 MPa (100 psig)
2836
Full Vacuum
0.62 MPa (90 psig)
Metric PN 6
2814 to 2836
Full Vacuum
0.60 MPa (87 psig)
Metric PN 10
2814 to 2824
Full Vacuum
1.00 MPa (145 psig)
2830
Full Vacuum
0.69 MPa (100 psig)
2836
Full Vacuum
0.62 MPa (90 psig)
56
Full Vacuum
Upper Limit
1.38 MPa (200 psig)
Process Temperature Limits
Lower Limit
-18°C (0°F)
Upper Limit
82°C (180°F)
6. Magnetic Flow Products
MI 019-179 – May 2015
Sanitary Flowtubes
2.4
300
1.65 MPa, 71˚C
2.0
1.65 MPa, -18˚C
1.38 MPa, 121˚C
1.6
1.2
ANSI CLASS 150 FLANGE
0.8
0.4
0
VACUUM AREA
FULL
VACUUM
-25
0
25
50
75 100 125 150 175
PROCESS PRESSURE, psi
PROCESS PRESSURE, MPa
Figure 15. Process Temperature and Pressure Limits - Sanitary Flowtubes
240 psi, 0˚F
250
200 psi, 250˚F
200
ANSI CLASS
150 FLANGE
150
100
50
0
VACUUM AREA
FULL
VACUUM
PROCESS TEMPERATURE, ˚C
240 psi, 160˚F
0
50 100 150 200 250 300 350 400
PROCESS TEMPERATURE, ˚F
Process Wetted Parts
The supplied process wetted parts are the flowtube lining and the electrodes. The electrode
material is printed on the data label. The lining material code is printed on the data plate as part
of the model number. The location of the code within the model number is shown below:
2802-SAZD-ASL-G
LINING MATERIAL
LINING MATERIAL
A = Polyurethane
T = ptfe
N = Neoprene
9100A and 9200A Magnetic Flowtubes
PED Certification
The PED (Harmonized Pressure Equipment Directive for the European Community)
certification is offered on flowmeters with DIN flanges. All other flange types are available with
PED certification upon special request. The CE marking on 9100A and 9200A Flowmeters with
PED certification carries the PED Notify Body number 0086.
Refer to the data plate to determine the model number, maximum temperature, lining material
and electrode material.
Process Pressure and Temperature Limits
The maximum process temperature is shown on the data label.
The process pressure limits are equal to the pressure limits of the flanges used.
Process Wetted Parts
The supplied process wetted parts are the flowtube lining and the electrodes. The lining and
electrode material codes are printed on the data plate.
57
MI 019-179 – May 2015
ISSUE DATES
APR 2002
JUL 2003
OCT 2003
OCT 2005
FEB 2007
JAN 2009
OCT 2011
DEC 2012
MAR 2015
MAY 2015
Vertical lines to the right of text or illustrations indicate areas changed at last issue date.
Invensys Systems, Inc.
10900 Equity Drive
Houston, TX 77041
United States of America
http://www.invensys.com
Global Customer Support
Inside U.S.: 1-866-746-6477
Outside U.S.: 1-508-549-2424
Website: http://support.ips.invensys.com
Copyright 2002-2015 Invensys Systems, Inc.
All rights reserved.
Invensys, Foxboro, and I/A Series are trademarks of
Invensys Limited, its subsidiaries, and affiliates. All other
trademarks are the property of their respective owners.
Invensys is now part of Schneider Electric.
0515