1. home and garden
2. bed and bath
3. bedroom
4. bedding and bed linens

TILE
POINTING
FLEXIBLE POINTING COMPOUND TO USE WITH HIP AND
RIDGE ROOF TILES.
DUNLOP TILE POINTING is an adhesive mechanical fastener for hip and ridge tiles, surpassing relevant
Australian standards. DUNLOP TILE POINTING achieves C4 Classification for approved use in cyclonic
regions (independently tested).
EXCEEDS AUSTRALIAN
STANDARD
ADHESIVE MECHANICAL
FASTENER
READY MIXED
10 YEAR GUARANTEE
NON-SLUMP
C4, CYCLONIC
REGION APPROVED
MECHANICAL
FASTENER
HIP & RIDGE
TILES
LOW VOC
BEFORE USE
All bedding material should be laid in accordance with
AS2050 (Installation of Roof Tiles) and allowed to air cure
until set, before application of tile pointing can
commence. During the bedding process, create a groove
in the bedding material under the ridge tile, this will
enhance the mechanical bond of the TILE POINTING. Stir
lightly before use and periodically through application to
avoid skinning of the material. Curing times will vary
with ambient conditions. Curing times will be slower
below 10˚C and will skin quickly in higher temperatures
over 30˚C.
SURFACE PREPARATION
Ensure surfaces are clean and free of any loose or
contaminating material including bedding material.
Bedding
Mortar
Tile
Pointing
Ridge Tile
Groove placed
in bedding mortar
provides a key for
Tile Pointing
PRECAUTIONS
Never add water to TILE POINTING. Instead, restir periodically through application. When not in use, replace lid on
bucket of TILE POINTING.
COVERAGE
Depending on application technique, 10L of TILE POINTING will cover approximately 20-22 lineal metres of
ridging.
HAZARD
When used according to directions, crystalline silica
contained in this product will not cause any negative
health effects.
SAFETY
Wear protective clothing and eye protection when
working with TILE POINTING avoiding any contact with
eyes and skin. This product is not classified as hazardous.
Material Safety Data Sheet is available on the Dunlop
Website.
FIRST AID
If product comes into contact with eyes, wash immediately with clean water. If product comes into contact with
skin, wash with soap and water.
APPLICATION
1. Apply pointing material at a thickness of 3-5mm
ensuring full contact with edge of the ridge cap.
2. Achieve a smooth finish with pointing trowel. Do not
CLEAN UP
use a sponge or brush.
Wash tools in warm water. Dispose of product and
3. Ensure application is in accordance with the tile being
packaging in accordance with local authority guidelines.
installed and the application environment.
4. TILE POINTING will require at least 2 hours to cure
before it will withstand any rain.
5. IMPORTANT: Wash off excess material with damp cloth.
Dried material will be difficult to remove.
6. After use, the TILE POINTING may be stored for future
use however cover with plastic sheet to prevent it from
skinning.
TILE
POINTING
GUARANTEE
Ardex Australia Pty Ltd (“we” or “us”) guarantees this
product (also referred to as “our goods”) is free from
manufacturing defects and will perform to any applicable
specification published by us for 10 years from the date
of application of the product if such application occurs
within this product’s specified shelf life. Our liability
under this guarantee is limited at our option to replacement of the product, repair of any damage to the immediate surface or area of application of the product, or the
cost of such replacement or repair, in each case if we are
satisfied loss or damage was due to a breach of this
guarantee. This guarantee does not apply if damage or
loss is due to failure to follow our published instructions
or any act or circumstance beyond our control, including
shade variations and efflorescence and faulty workmanship on the part of any installer or applicator of the
product. If you wish to make a claim under this guarantee you must notify us (address: 7/20 Powers Road Seven
Hills NSW 2147; phone: 1800224070;
email: [email protected]), identify the
product and provide evidence of your purchase and the
subsequent application of the product within 30 days of
any alleged loss or damage occurring. We reserve the
right to ask you for satisfactory evidence of any alleged
loss or damage and to undertake any inspections and
tests necessary to establish your rights under this guarantee. Any claim under this guarantee is at your cost. This
guarantee is in addition to any rights or remedies you
may have as a “consumer” under the Australian Consumer Law and to that extent you need to be aware that:
“Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss
of damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major
failure”. Please note that this guarantee does not cover
colour variation as this may be caused by efflorescence
from the bedding mortar.
TOLL FREE SERVICE
1800 222 841 (AU)
0800 224 070 (NZ)
ARDEX AUSTRALIA PTY LTD
ABN 82 000 550 005
7/20 Powers Road
Seven Hills NSW 2147
Ph: 1300 788 780
ARDEX NEW ZEALAND LTD
32 Lane St
Woolston Christchurch NZ
Ph: (03) 373 6900