How To configure Nortel/Avaya Media Gateway Controller (MGC) with UCx server
How To configure Nortel/Avaya Media Gateway Controller (MGC) with UCx server UCx 4.0 How To configure Nortel/Avaya Media Gateway Controller (MGC) with UCx server This document contains E-MetroTel confidential information and is provided for the internal business use of our partners. This document shall not be disclosed to any third party without the express written consent of E-MetroTel. Property of E-Metrotel 2014. 24-May-2014 Page 1 of 14 Copyright © 2014 E-Metrotel Global Inc. How To configure Nortel/Avaya Media Gateway Controller (MGC) with UCx server UCx 4.0 Table of Contents Feature Description ____________________________________________________________________ 3 Pre-Requisites ________________________________________________________________________ 4 MGC DSP daughterboard _______________________________________________________________ 5 Supported combination of DSP daughterboards _____________________________________________ 5 Configuring the MGC ___________________________________________________________________ 6 Configuring existing MGC with ELAN connectivity ___________________________________________ 6 Configuring a New MGC card ___________________________________________________________ 6 Configuring the UCx Server ______________________________________________________________ 7 Configuring M3900 series Nortel Digital phone sets ___________________________________________ 8 MGC Registration with UC x Server _______________________________________________________ 10 MGC specific information _______________________________________________________________ 11 Updating TLAN IP parameters _________________________________________________________ 11 MGC Registration Status ______________________________________________________________ 11 MGC Loadware information ____________________________________________________________ 11 Recommended MGC Loadware ________________________________________________________ 11 Procedure to reset MGC password ______________________________________________________ 12 References __________________________________________________________________________ 14 24-May-2014 Page 2 of 14 Copyright © 2014 E-Metrotel Global Inc. How To configure Nortel/Avaya Media Gateway Controller (MGC) with UCx server UCx 4.0 Feature Description To support the integration of Nortel Meridian Taurus M3902/M3903/M3904 and Aries 2008/2616 digital phone sets into the UCX server, there are certain configuration settings required in the Media Gateway Controller (MGC) card and in the UCX server. With this integration, the features supported on the phones include: Call Forward Call Transfer Voice Mail functions Last Number Redial Busy Lamp Field (BLF) and many more ... 24-May-2014 Page 3 of 14 Copyright © 2014 E-Metrotel Global Inc. How To configure Nortel/Avaya Media Gateway Controller (MGC) with UCx server UCx 4.0 Pre-Requisites UCX server is installed with E-Metrotel Release 4.0 software. CS1000 hardware: Meridian Option 11 (10 card) cabinet / CS1000 (4 card) chassis / MG1010 cabinet Media Gateway Controller (MGC) card One or two DSP daughter-boards (32-port, 96-port, 128-port) Digital Line Cards (DLC) M2008, M2616, M390x phone sets connected to phone set panel IP addresses The IP addresses assigned to UCX server, MGC ELAN, MGC TLAN and MGC DSP daughterboard TLAN must be in the same subnet. e.g. 192.168.1.x If MGC is registered in security domain of CS1000 system, it has to be de-registered first before registering with UCX server. Please refer to page 11 of the Avaya CS100 Security Domain Guide. 24-May-2014 Page 4 of 14 Copyright © 2014 E-Metrotel Global Inc. How To configure Nortel/Avaya Media Gateway Controller (MGC) with UCx server UCx 4.0 MGC DSP daughterboard Supported combination of DSP daughterboards The following marking is present on MGC circuit board for daughterboard placement.DSP daughterboard slot 1: D/B 1 SLOT 11 LOW OR HIGH DENSITYDSP daughterboard slot 2: D/B 2 SLOT 0 LOW DENSITY ONLY 32-port DSP daughterboard NTDW62xx is supported in DB SLOT 1 and SLOT2 96-port DSP daughterboard NTDW64xx is supported only in DB SLOT 1 128-port DSP daughterboard NTDW78xx is supported only in DB SLOT 1 24-May-2014 Page 5 of 14 Copyright © 2014 E-Metrotel Global Inc. How To configure Nortel/Avaya Media Gateway Controller (MGC) with UCx server UCx 4.0 Configuring the MGC Configuring existing MGC with ELAN connectivity If this is an existing MGC card with network connectivity, perform the following steps: 1. Login to MGC. 2. Enter the command mgcsetup 3. Step through the prompts until you get to Primary CS IP 4. Enter the UCX server IP address (e.g. 192.168.1.200) at this prompt 5. Proceed through the rest of the prompts without any changes 6. Reboot the MGC card ldb> mgcsetupELAN IP : 192.168.1.210ELAN subnet mask : 255.255.255.0ELAN gateway IP : 192.168.1.1Primary CS IP : 192.168.1.100 ? 192.168.1.200 Configuring a New MGC card If this is a new MGC card with no network connectivity, perform the following steps: 1. Connect to MGC card via the serial port. 2. Enter the command mgcsetup to configure the MGC ELAN parameters 3. Configure the UCX server IP address at Primary CS IP prompt (e.g. 192.168.1.200) 4. Proceed through the rest of the prompts without any changes 5. Reboot the MGC card ldb> mgcsetupELAN IP : 192.168.1.210ELAN subnet mask : 255.255.255.0ELAN gateway IP : 192.168.1.1Primary CS IP : 192.168.1.200 24-May-2014 Page 6 of 14 Copyright © 2014 E-Metrotel Global Inc. How To configure Nortel/Avaya Media Gateway Controller (MGC) with UCx server UCx 4.0 Configuring the UCx Server Perform the following steps to configure the MGC on the UCX server: 1. Open the UCX Web-based Configuration Utility 2. From the PBX tab, select Media Gateway 3. Select New Media Gateway to add the MGC 4. Enter the MGC configuration values 5. Press the Create button 24-May-2014 Page 7 of 14 Copyright © 2014 E-Metrotel Global Inc. How To configure Nortel/Avaya Media Gateway Controller (MGC) with UCx server UCx 4.0 Configuring M3900 series Nortel Digital phone sets To configure a M3900 series Nortel digital set, see Adding a Nortel Extension in the Administration Guide. Under Nortel Properties, select the Device type from the pull-down list that matches your M3900 series digital set. Once the configuration is complete and the changes have been applied, the digital set will become active and display the following information: Extension Date and time Powered by UCx (39xx phone) The programmable keys can be configured for Call Transfer, CallForward and Voicemail features on M2008 and M2616 set. The programmable keys are available on Nortel Properties page of the set. Programmable keys on M2008 Programmable keys for M2616 24-May-2014 Page 8 of 14 Copyright © 2014 E-Metrotel Global Inc. How To configure Nortel/Avaya Media Gateway Controller (MGC) with UCx server UCx 4.0 Busy Lamp Field (BLF) feature setting with Programmable keys on M3904 24-May-2014 Page 9 of 14 Copyright © 2014 E-Metrotel Global Inc. How To configure Nortel/Avaya Media Gateway Controller (MGC) with UCx server UCx 4.0 MGC Registration with UC x Server After configuration of the MGC is complete, the card will register with the UCX Server. The MGC faceplate will display the configured superloop and shelf. The mgcinfoshow command will display the configured parameters, as seen in the example below: ldb> mgcinfoshowRegistration Status: Registered on 192.168.1.200 UpTime: 0 days, 02 hours, 03 minutes, 08 seconds MGC Hostname: MGCMGC ELAN IP Address: 192.168.1.210MGC Subnet Mask: 255.255.255.0MGC Gateway Address: 192.168.1.1 MGC TLAN IP Address: 192.168.1.212MGC Subnet Mask: 255.255.255.0MGC Default GW: 192.168.1.1 Primary CS Hostname: ucx50.emetrotelPrimary CS IP Address: 192.168.1.200 DB1 NT code: NTDW64AADB1 TLAN IP Address: 192.168.1.214DB1 TN: 008 0 11 DB2 NT code: NTDW62AADB2 TLAN IP Address: 192.168.1.215DB2 TN: 008 0 0 Media Gateway Information Superloop Shelf: 008 0 TDS Loop: 110 111 CONF Loop: 112 113 Active TLAN port: Port 7 = 2T Bottom face plate connectorTLAN port designator: 2TTLAN set to 100Mbps full duplex. Active ELAN port: Port 6 = 1E Second from bottom face plate connectorELAN port designator: 1EELAN set to auto negotiate.ELAN security Disabled The TLAN IP and DSP daughterboard IP parameters entered in the UCX Media Gateway panel must match the MGC configuration as displayed via the mgcinfoshow command. If the TLAN IP parameters do not match the values entered in the UC X Media Gateway panel, speech path will be affected. 24-May-2014 Page 10 of 14 Copyright © 2014 E-Metrotel Global Inc. How To configure Nortel/Avaya Media Gateway Controller (MGC) with UCx server UCx 4.0 MGC specific information Updating TLAN IP parameters In the event an MGC card fails to configure the TLAN IP parameters after registering with UC X server, the following steps can be used to update TLAN IP parameters: 1. Login to MGC. 2. Use the command mgcTlanUpdate to update the TLAN IP parameters 3. In the example below, the parameters configured are: 192.168.1.20 is the TLAN IP address ffffff00 represents the subnet mask 255.255.255.0 192.168.1.1 is the TLAN gateway address ldb>mgcTlanUpdate "192.168.1.20:ffffff00", "192.168.1.1" MGC Registration Status 1. Login to MGC. 2. Use the command mgcinfoshow to query MGC registration status. ldb>mgcinfoshow MGC Loadware information 1. Login to MGC. 2. Use the command swversionShow to query MGC loadware information. ldb>swversionShow Recommended MGC Loadware The following is the recommended MGC loadware baseline. MGC with other loadware 24-May-2014 Page 11 of 14 Copyright © 2014 E-Metrotel Global Inc. How To configure Nortel/Avaya Media Gateway Controller (MGC) with UCx server UCx 4.0 BOOTCODE: MGCBAP01 CSP: MGCCCD01 MSP: MGCMAB01 FPGA: MGCFAA16 APPLICATION: MGCAAA08 DB1: DSP1AB03 DB2: DSP2AB03 BCSP: MGCCCD01 MGC with CSP loadware MGCCAH17 will not work with UCX 4.0 software. Procedure to reset MGC password The password can be reset on MGC with telnet connection to MGC card ELAN IP address or through a serial port connection. This procedure will not work through SSH connection. This procedure requires easy physical access to MGC card, as the reset button on faceplate of MGC card needs to be pressed. 24-May-2014 Page 12 of 14 Copyright © 2014 E-Metrotel Global Inc. How To configure Nortel/Avaya Media Gateway Controller (MGC) with UCx server UCx 4.0 This is the login prompt through a telnet connection to MGC card's ELAN IP address: login: With telnet connection, type CTRL+ldb to get the following prompt: LDB login on /pty/pty00.SUsername: resetPWD Type resetPWD at Username: prompt as shown above. PWRD will be displayed on the MGC faceplate display. Enter admin2 for userID. Press the reset faceplate button on MGC card within 60 seconds. Press the ENTER key on keyboard within 60 seconds. Enter new PWD2 password twice. Enter new PDT2 password twice. Login to MGC with login: PDT2 and newly set password. ****************************************************************** WARNING: All attempts to use the Password Reset Mechanism ** are logged. In order to proceed, you will need ** physical access to the Call Server. ****************************************************************** If you do not wish to proceed, enter the word QUIT, otherwiseenter the PWD2/Admin2 userID: admin2 You have 60 seconds to push the reset faceplate button You have 60 seconds to press ENTER: Enter new PWD2 password:Reenter new PWD2 password: Enter new PDT2 password: Reenter new PDT2 password: ### PWD2 password successfully changed. ###### PDT2 password successfully changed. ### 24-May-2014 Page 13 of 14 Copyright © 2014 E-Metrotel Global Inc. How To configure Nortel/Avaya Media Gateway Controller (MGC) with UCx server UCx 4.0 References Document Link Avaya CS1000E Installation and http://downloads.avaya.com/css/P8/documents/100119924 Commissioning Release 7.5 Document NN43041-310 Avaya CS100 Security Domain Guide http://198.152.212.23/css/P8/documents/100144217 MGC card configuration http://pbxbook.com/meridian/mgcset.html 24-May-2014 Page 14 of 14 Copyright © 2014 E-Metrotel Global Inc.
© Copyright 2024