PS3 RaptorFire Clip Instruction How to Use Step # 1 When you receive the chip, and install it onto your PlayStation 3 Controller, you must do the following: Initial Programming Mode • Press down on the D-‐pad and hold to activate the Chip • Once activated, the player 4 Led will light up Purple • The color will represent what Exclusive Mod you want to be activated or disabled. Below is a color chart. • Press X for Yes (activate) and O for NO (do not activate). OPTIONS LED 4 COLOR Option 1 Option 2 Option 3 Option 4 Option 5 Option 6 * AFTER OPTION 6 IS POINT OF NO RETURN * LED 3 COLOR X FOR YES HIT HIT O FOR NO FUNCTION SNIPER DROP SHOT AKIMBO JITTER QUICK KNIFE BURST DISPLAY ON L ED 3 DISPLAY ON LED 3 STEP # 2 The menu system is setup in 3 Classes. (Once you finished the programming, Press down on the Dpad and hold to enter Class 1, and browse by holding down on the Dpad.) •
•
•
Class 1 is marked by a Blue Led in Player 4 Slot Class 2 is marked by a Purple Led in Player 4 Slot Class 3 is marked by a Green Led in the Player 4 Slot Make sure you browse through the classes by holding down on the Dpad until you complete the cycle from Blue, Purple, and Green. The 4th Dpad Down, will shut off the Chip. If you hold it down again, it will activate the chip with the Class 1 again lighting up Blue in player 4 Slot. STEP # 3 Very Important Step Assigning Mods to Each Class -‐ Each Class has 2 Available Empty Slots -‐ Total of 6 Slots, since there are 2 in each Class. Activating Slots: When you hold DOWN on the D-‐Pad, and you enter the 1st Class, Hold UP on the Dpad until your player 3 LED lights up Blue (Default RapidFire). This activates SLOT 1. We have a color chart that shows all the modes and sub-‐modes that can be assigned to each slot. To Assign an Exclusive Mod to SLOT 1, hold LEFT on the D-‐pad and hold the corresponding button on the chart for the exclusive add-‐on you would like to select. The player 3 LED will switch to the color of the exclusive add-‐on that you have selected. To switch to SLOT 2, hold UP on the D-‐pad until the player 3 LED blinks, indicating you are now in SLOT 2. To turn off the SLOTS, hold up on the D-‐pad until the player 3 LED turns off. Repeat these steps to cycle between SLOT 1, SLOT 2, and OFF. Slot 1: With SLOT 1 selected, if you wanted Drop Shot, hold LEFT DPAD and CIRCLE, and your Player 3 Led will light up RED. It will blink a number of times representing the MODE that you are selecting. For example, if you want to select MODE 2 of drop shot, hold the left D-‐pad and the CIRCLE button until the player 3 light blinks 2 times. Let go immediately. If it blinks 3 times, you will be in MODE 3. A white light will blink after you let go confirming the MODE has been selected. There are multiple Drop Shot Sub-‐Modes as well as multiple modes for the other exclusive mods (i.e. Akimbo, jitter, burst, etc). If you wanted to choose a different exclusive add-‐on from the Chart, just repeat the function by Holding Down LEFT DPAD and the exclusive add-‐on’s corresponding button (see chart) and your player 3 Led will change to the color that corresponds to the option on the Chart you would like to select. Slot 2: To Enter Slot 2 of any class, hold UP on the DPAD, and your player 3 LED will flash again, indicating its ready for programming (see previous step). Remember, all the Slots are blue by default for Rapid fire. STEP 4 Adjusting Rapid Fire Speed and Burst Modes Example: (When you are in Class 1, Slot 1 and player 3 led is Blue) Hold down the Left Dpad, until Player 3 & 4 Led will flash Red continuously. You will use L1 to decrease shots per second and R1 to increase speed setting (in increments of 1). When you press the L1 buttons to decrease, player 4 LED will flash once. After, player 4 LED will flash a number of times indicating the tens value and the player 3 LED will flash a number of times indicating the ones value. For example, when Player 4 flashes 1 time, this will represent ten and Player 3 flashes 3 times will represent 3 for speed setting 13. You will need to count the amount of times each player led flashes to know what speed setting you are on. Once you decide and have selected which speed setting you want, HOLD DOWN LEFT DPAD, and it will save the Speed setting forever. The same process applies to adjusting the number of rounds per burst when using burst mode. Suggested MW3 Speeds 11-‐13 Shots per second (speed setting 11-‐13). NOTE: The classes and slots were designed to be programmed and used in live game play by the use of the D-‐Pad to browse through the modes. This makes it convenient to change your setting while playing the game. Today we are proud to release this chip, and hope everyone understands the achievement of this project. SPEED SETTINGS
Speed 17
Speed 16
Speed 15
Speed 14
Speed 13
Speed 12
Speed 11
Speed 10
Speed 9
Speed 8
Speed 7
Speed 6
Speed 5
Speed 4
Speed 3
Speed 2
Speed 1
SP’S 25
SP’S 20
SP’S 15
SP’S 14
SP’S 13
SP’S 12
SP’S 11
SP’S 10
SP’S 9
SP’S 8
SP’S 7
SP’S 6
SP’S 5
SP’S 4
SP’S3
SP’S 2
SP’S 1
MODES
Modes are selected by pressing and holding either the user button or DPAD left in addition to button indicated by chart below,
colors correspond to mode led. When selecting the number of times LED flashes is the corresponding mode number.
Release buttons on corresponding LED mode flash to select that mode
Edit Speed can be entered when a class mode is on. Press and hold either user
button are DPAD ribght with nothing else held to enter edit mode.
Once edit mode is entered LEDS 3 and 4 will flash RED. To increment
speed hold R1, each flash represents +1 to speed delay
RAPIDFIRE #Of Modes
1
Button R1
Mode 1
Rapid fire on trigger
AKIMBO
# Of Modes
Mode 1
Mode 2
Mode 3
Mode 4
Mode5
BURST
# OF Modes
4
Button X
Mode 1
2 Round burst on trigger
Mode 2
3 Round burst on trigger
Mode 3
4 Round burst on trigger
Mode 4
4 Round burst on trigger
SNIPER
# OF Modes
3
Button Leftstick
Mode 1
Quickscope1: ADS automatically fires weapon as soon as weapon pulls up speed (Faster)
Mode 2
Sniper hold breath: ADS automatically presses hold breath button when pressed
Mode 3
Sniper hold breath 2 round burst: Automatic hold breath and 2 round burst
Speed Shots Per/Sec Display On LED 3&4 / LED 4 Display 10’s and 20’s and
LED 3 Display 1-9 for Ex: for Speed 15LED 4 blink once for 10 and LED 3
blink 5 times for 5 for 15 shots. 15 Shots per second
5
Button L1
Akimbo RF: Rapidfire on trigger and ADS
Easy AKIMBO RF: Rapidfire on trigger and ADS automatically with trigger pull
Easy AKIMBO: Trigger press automatically presses ADS (Easy Akimbo for machine guns)
AUTOAIM: Ads toggles to automatically lock on enemies using aim assist (works with zombies)
AUTOAIM RF: ADS locks onto enemies and triggers are rapidfire
*** Quick scope Note: Quick scope is adjustable with the speeds, speed setting 1 is the fastest setting and speed setting 17 is the slowest. ***
DROPSHOT # OF MODES
4
Button: CIRCLE
MODE 1 Dropshot: Crouch Button is held when trigger is pressed (Player Lays Down)
MODE 2 Dropshot AI: Dropshot is inhibited when ADS is held
MODE 3 Dropshot RF: Player drops when trigger is pressed. Trigger has Rapid Fire
MODE 4 Dropshot RF AI: Dropshot RF is inhibited when ADS is held. While aiming trigger has normal Rapid Fire.
JITTER
# OF MODES
4
Button: Triangle
Mode 1
Jitter: Rapid fire glitch that makes M16 rapid fire (PRE MW3)
Mode 2
Jitter Al: Jitter aim inhibited.
Mode 3
Jitter Al -> RF: Jitter aim inhibited. Trigger has rapid fire when ain is inhibited. (PRE MW3)
QUICK MELEE # OF MODES
3
BUTTON: Right Stick
Mode 1
Quick Knife 1 : When melee is pressed quick knife routine loops. Has to have semtex or tom hawk equipped. (FAST)
Mode 2
Quick Riot: When melee is pressed and riot shield is equipped, quick riot routine loops. Has to have semtex equipped. (MEDIUM)
Mode 3
Quick Knife 2 : When melee is pressed quick knife routine loops. Has to have Semtex or Tomahawk quipped. ( SLOWEST)
*** QUICK KNIFE NOTE: Mode1 works on MW3 with semtex, as well as BLACK OPS with Tom Hawk equipped. If BLACK OPS semtex is used, use MODE 3.***
1
2
LAYOUT TYPES
LAYOUT
Layout is selected when mod is off (mode and class LED must be off) by pressing and holding DPAD Right.
When holding LED 4 will light up white and LED 3 will flash shortly after.
Every time LED 3 flashes it corresponds to a layout number. Release DPAD Right when it corresponding layout mode number flash has occurred.
LED 3 and 4 will flash the number of times that corresponsds to the layout number and saves the layout.
LAYOUT # CORRESPONDING LAYOUT
1
2
3
4
5
6
7
8
9
10
Default
Tactical
Lefty
Nom4d
Nom4d Tactical
Flip Default
Flip Tactical
Flip Lefty
Flip Nom4d
Flip Nom4d Tactical
ůĂĐŬKƉƐ&ŝƌĞĚƐ>ĞƚŚĂůdĂĐƟĐĂůDĞůĞĞƌŽƵĐŚ,ŽůĚƌƚ
Default
R1
L1
R2
L2
RST
O
LST
dĂĐƟĐĂůZϭ>ϭZϮ>ϮK Z^d>^d
>ĞŌǇ>ϭZϭ>ϮZϮ>^dKZ^d
Nom4d
R1
L1
R2
L2
O
RST
LST
Charlie
R1
R2
L1
L2
RST
O
LST
Default Alt
R2
L2
R1
L1
RST
O
LST
&ůŝƉdĂĐƟĐĂůZϮ>ϮZϭ>ϭK Z^d>^d
&ůŝƉ>ĞŌǇ>ϮZϮ>ϭZϭ>^d KZ^d
Flip Nom4d R2
L2
R1
L1
O
RST
LST
Dtϯ&ŝƌĞĚƐ>ĞƚŚĂůdĂĐƟĐĂůDĞůĞĞƌŽƵĐŚ,ŽůĚƌƚ
Default
R1
L1
R2
L2
RST
O
LST
dĂĐƟĐĂůZϭ>ϭZϮ>ϮKZ^d>^d
>ĞŌǇ>ϭZϭ>ϮZϮ>^dK>^d
Nom4d
R1
R2
L1
L2
RST
O
RST
EŽŵϰĚdĂĐƟĐĂů R1
R2
L1
L2
O
RST
O
Default Flip R2
L2
R1
L1
RST
O
LST
dĂĐƟĐĂů&ůŝƉZϮ>ϮZϭ>ϭKZ^d>^d
>ĞŌǇ&ůŝƉ>ϮZϮ>ϭZϭ>^dK>^d
Nom4d Flip R2
R1
L2
L1
RST
O
RST
Nom4d TAC Flip R2
R1
L2
L1
O
RST
O
Dtϯ&ŝƌĞĚƐ>ĞƚŚĂůdĂĐƟĐĂůDĞůĞĞƌŽƵĐŚ,ŽůĚƌƚ
Default
Default Flip
R1
R2
L1
L2
R2
R1
L2
L1
RST
RST
O
O
LST
LST
dĂĐƟĐĂůZϭ>ϭZϮ>ϮKZ^d>^d
dĂĐƟĐĂů&ůŝƉZϮ>ϮZϭ>ϭKZ^d>^d
>ĞŌǇ>ϭZϭ>ϮZϮ>^d K>^d
>ĞŌǇ&ůŝƉ>ϮZϮ>ϭZϭ>^dK>^d
Nom4d
Nom4d Flip
3
R1
R2
R2
R1
L1
L2
L2
L1
RST
RST
O
O
RST
RST
EŽŵϰĚdĂĐƟĐĂů R1
Nom4d TAC Flip R2
R2
R1
L1
L2
L2
L1
O
O
RST
RST
O
O
4