DuPont Imron Elite System Chart How to take the guesswork out of productive repair work ™ USAGE PRODUCT DESCRIPTION MIX RATIO COMPONENTS ADDITIVES ® APPLICATION DRY TIME IMPORTANT NOTES MetaLok® - CVP Pretreatment 1 to 1 255S™ Activator N/A Apply using a cross-coat technique. METAL ™ TREATMENT 250-S Recommended film build is 0.6 - 0.8 mils DFT. Dry time to touch is 10 minutes. Dry time prior to Primer or Sealer application is 30 minutes. 250-S™ MetaLok® – CVP must be primed or sealed prior to topcoat application. MetaLok® - CVP Pretreatment 3 to 1 236S™ Activator N/A Apply using a cross-coat technique. ™ 235-S Recommended film build is 0.6 - 0.8 mils DFT. Dry time to touch is 10 minutes Dry time prior to Primer or Sealer application is 30 minutes. 235-S™ MetaLok® – CVP is 3.5 VOC, Chrome-Free and Rule 66 compliant. MetaLok® - CVP must be primed or sealed prior to topcoat application. PRIMER High Solids URO® Primer 4 to 1 193S™ Activator or 389S™ or 8989S™ Apply medium wet coats using a cross-coat No flash time is required between 1220S™, 1340S™ and 1380S™ may be topcoated SURFACER 1220S™ URO® Primer - 3.5 VOC 194S™ Activator Accelerator technique to desired film build. coats of URO® Primer. with Imron® Elite BC Basecoat after a 1340S™ URO® Primer - 2.8 VOC 15 - 20 minute flash. ™ ® 1380S URO Primer - 2.1 VOC Refer to Technical Data Apply using cross-coat technique. Recommended Dry to sand is equal to 2 - 4 hours when Sheet for usage film build is 0.8 - 1.0 mils DFT per pass. accelerator is used. recommendations. 936S™Activator N/A Apply medium wet coats using a cross-coat ™ or 937S Slow technique to desired film build. Activator Apply using a cross-coating technique. Recommended film build is 1.0 to 1.8 mils DFT. Dry time prior to topcoat is 30 minutes for 1 coat of 934S™, or 60 minutes for 2 coats. 934S™must be sanded if allowed to cure longer than 72 hours prior to topcoat. SINGLE- Imron® Elite SS 3 to 1 194S™ Activator 389S™ or 8989S™ STAGE Paint Type EAAccelerator and 359S™ Paint Additive Refer to Technical Data Sheet for usage recommendations. Flash times between coats will vary between 30 seconds and 5 minutes. Shorter flash time between cross-coats results in smoother topcoat appearance. BASECOAT Imron® Elite BC 3 to 1 194S™ Activator 389S™ Accelerator Apply Imron® Elite BC using a cross-coat Flash times between coats will vary Paint Type EB technique. between 30 seconds and 5 minutes. Refer to Technical Data Sheet for usage Spray a wet first coat using a top-to-bottom recommendations. motion. Spray a medium wet second coat using a side-to-side motion. Shorter flash time between cross-coats results in smoother topcoat appearance. PRIMER SEALER Corlar® 934S™ 5 to 1 Apply Imron® Elite SS using a cross-coat technique. Spray a wet first coat using a top-to-bottom motion. Spray a medium wet second coat using a side-to-side motion. CLEARCOAT Imron® Elite Clear Coat 8840S™ 3 to 1 194S™ Activator389S™ Accelerator and Apply Imron® Elite 8840S™ clear coat using Flash times between the cross-coats of 8840S™ can be applied wet-on-wet 359S™ Paint Additive a cross-coat technique. 8840S™ is not necessary. over Imron® Elite BC Basecoat (solid, metallic and pearl), and Imron® Elite SS Refer to Technical Data Spray a medium wet first coat using a Single-Stage solid colors (metallic colors Sheet for usage top-to-bottom motion. are recommended to cure overnight). recommendations. Spray a medium wet second coat using a side-to-side motion. Some products listed above may not be sold in Canada. Consult your local DuPont representative for recommended products. DuPont CoatingSolutions E-R3924 Copyright © 2005 DuPont. All rights reserved. The DuPont Oval Logo, DuPont™, The miracles of science™, MetaLok®, URO®, Corlar® and Imron® are registered trademarks or trademarks of DuPont or its affiliates.