1. technology and computing
2. hardware
3. computer networking
4. router

How To: Install a Road Glide iPhone / GPS Mount | Iron Aces Speed Shop
NAVIGATION 
How To: Install a Road Glide iPhone / GPS Mount
Posted on July 11, 2013 by Chris Trausch in How To
In this ‘How To’ we’re going to walk you through the installation process for the Iron Aces Road
Glide iPhone / GPS Mount. This is a quick and easy install and should only take approximately
15-20 minutes from start to finish.
** IMPORTANT **
Iron Aces Speed Shop is not responsible for the operation of the Road Glide iPhone / GPS
Mount or its compliance with highway regulatory and safety standards. Please use common
sense and do not operate either device while riding your motorcycle. Doing so is at your
own risk.
Tools Required
Allen wrench – 7/64″
Blue Loctite
Drill
(2) Drill bits – 3/32″; 5/32″
Flathead screwdriver – small head
Philips head screwdriver
http://blog.ironacesspeedshop.com/how-to/how-to-install-a-road-glide-iphone-gps-mount/[4/14/2014 3:28:19 PM]
How To: Install a Road Glide iPhone / GPS Mount | Iron Aces Speed Shop
Torque wrench (optional)
Torx bit – T-25
Included in the package with your Road Glide iPhone / GPS Mount are the following hardware
that will be used to install both the Road Glide Mount to your bikes instrument bezel along with
hardware for attaching your particular device cradle to the Road Glide Mount.
Step 1
Using a T-25 Torx bit, remove screws from each side of the instrument bezel. Once screws are
removed, use thumbs to push tabs at the rear of bezel from stop in front of the ignition switch. Gently raise free side of bezel until tabs at the front of the instrument nacelle become
disengaged from slot at the from of the bezel (concealed behind decorative adhesive strip).
http://blog.ironacesspeedshop.com/how-to/how-to-install-a-road-glide-iphone-gps-mount/[4/14/2014 3:28:19 PM]
How To: Install a Road Glide iPhone / GPS Mount | Iron Aces Speed Shop
Step 2
Raising bezel slightly, disconnect instruments and indicator lights from interconnect harness
(speedometer, tachometer, indicator lights).
http://blog.ironacesspeedshop.com/how-to/how-to-install-a-road-glide-iphone-gps-mount/[4/14/2014 3:28:19 PM]
How To: Install a Road Glide iPhone / GPS Mount | Iron Aces Speed Shop
Step 3
Remove bezel from motorcycle.
http://blog.ironacesspeedshop.com/how-to/how-to-install-a-road-glide-iphone-gps-mount/[4/14/2014 3:28:19 PM]
How To: Install a Road Glide iPhone / GPS Mount | Iron Aces Speed Shop
Step 4
Using narrow flathead screwdriver, gently remove decorative adhesive strip from the top of the
instrument bezel by pressing from behind until decorative adhesive strip is free.
** RECOMMENDED **
Saving the removed decorative adhesive strip is recommended incase you decide to
remove the Road Glide iPhone / GPS Mount at a later time.
http://blog.ironacesspeedshop.com/how-to/how-to-install-a-road-glide-iphone-gps-mount/[4/14/2014 3:28:19 PM]
How To: Install a Road Glide iPhone / GPS Mount | Iron Aces Speed Shop
Step 5
Cut out the Drill Guide from the installation guide that was included with your Road Glide iPhone /
GPS Mount. Insert drill template into place where decorative adhesive strip has been removed
and mark drill holes with a scribe or small drill bit.
http://blog.ironacesspeedshop.com/how-to/how-to-install-a-road-glide-iphone-gps-mount/[4/14/2014 3:28:19 PM]
How To: Install a Road Glide iPhone / GPS Mount | Iron Aces Speed Shop
Step 6
Using a 3/32″ drill bit, drill two pilot holes. Once pilot holes are drilled, use a 5/32″ drill bit to drill
the final holes through the instrument bezel. Clean drilled holes of any plastic burrs.
** IMPORTANT **
During Step 6, use extreme caution while drilling through the instrument bezel as the
composite plastic has a tendency to grab the drill bit, pulling the bezel into the drill. To
protect the bezel, place a towel between the bezel and drill before drilling. An extra set of
hands is recommended to hold the bezel while you drill.
http://blog.ironacesspeedshop.com/how-to/how-to-install-a-road-glide-iphone-gps-mount/[4/14/2014 3:28:19 PM]
How To: Install a Road Glide iPhone / GPS Mount | Iron Aces Speed Shop
Step 7
Insert backing plate into place.
http://blog.ironacesspeedshop.com/how-to/how-to-install-a-road-glide-iphone-gps-mount/[4/14/2014 3:28:19 PM]
How To: Install a Road Glide iPhone / GPS Mount | Iron Aces Speed Shop
Step 8
If you will be using the AMPS 4-hole pattern (Zumo users), place two nylon lock nuts (nylon
facing out) into the mounting boss channel, prior to attaching the mount to the instrument bezel.
http://blog.ironacesspeedshop.com/how-to/how-to-install-a-road-glide-iphone-gps-mount/[4/14/2014 3:28:19 PM]
How To: Install a Road Glide iPhone / GPS Mount | Iron Aces Speed Shop
Step 9a
Carefully place the Road Glide iPhone / GPS Mount into place on the front of the instrument
bezel then thread supplied screws into place using a 7/64″ allen wrench to snug.
** RECOMMENDED **
Use blue Loctite on screw threads prior to installation to prevent loosening.
http://blog.ironacesspeedshop.com/how-to/how-to-install-a-road-glide-iphone-gps-mount/[4/14/2014 3:28:19 PM]
How To: Install a Road Glide iPhone / GPS Mount | Iron Aces Speed Shop
Step 9b
With the mount attached to the instrument bezel you are ready to attach your device. Here you
can see the backing plate keeping the two nylon lock nuts in place.
http://blog.ironacesspeedshop.com/how-to/how-to-install-a-road-glide-iphone-gps-mount/[4/14/2014 3:28:19 PM]
How To: Install a Road Glide iPhone / GPS Mount | Iron Aces Speed Shop
Step 10
Once the Road Glide iPhone / GPS Mount is affixed to the instrument bezel, fasten the device
cradle.
iPhone Users – Fasten the RAM Mount to the far left of the mount with the disconnect tab
pointing to the right.
Zumo Users – Use the supplied hardware to fasten your 5xx, 6xx or 350LM cradle to the
four Zumo specific location holes.
http://blog.ironacesspeedshop.com/how-to/how-to-install-a-road-glide-iphone-gps-mount/[4/14/2014 3:28:19 PM]
How To: Install a Road Glide iPhone / GPS Mount | Iron Aces Speed Shop
Step 11
Reconnect speedometer, tachometer and indicator light connectors into the instrument bezel
interconnect harness.
http://blog.ironacesspeedshop.com/how-to/how-to-install-a-road-glide-iphone-gps-mount/[4/14/2014 3:28:19 PM]
How To: Install a Road Glide iPhone / GPS Mount | Iron Aces Speed Shop
Step 12
After verifying that the left and right sides of the instrument nacelle are properly mated, insert tab
at rear of instrument bezel into slot of instrument nacelle (just in front of the ignition switch). Holding left and right sides of nacelle together, place bezel over instrument nacelle flange. When
properly mated, tabs at front of instrument nacelle engage lip in slot at front of bezel.
http://blog.ironacesspeedshop.com/how-to/how-to-install-a-road-glide-iphone-gps-mount/[4/14/2014 3:28:19 PM]
How To: Install a Road Glide iPhone / GPS Mount | Iron Aces Speed Shop
Step 13
Install screw on each side of the instrument bezel. Harley-Davidson recommends tightening the
screws to 25-35 in-lbs. If you do not have a torque wrench do not use a ratchet, instead tighten
to snug with fingers.
** IMPORTANT **
Since screws thread into plastic, over tightening will strip the threads.
http://blog.ironacesspeedshop.com/how-to/how-to-install-a-road-glide-iphone-gps-mount/[4/14/2014 3:28:19 PM]
How To: Install a Road Glide iPhone / GPS Mount | Iron Aces Speed Shop
Step 14
iPhone Users – Place your iPhone into the RAM Mount cradle bottom first then snap the top into
place.
Other Device Users – Place your device in the cradle according to manufacturer instructions for
your specific device.
http://blog.ironacesspeedshop.com/how-to/how-to-install-a-road-glide-iphone-gps-mount/[4/14/2014 3:28:19 PM]
How To: Install a Road Glide iPhone / GPS Mount | Iron Aces Speed Shop
Step 15
Installation complete! Time to start enjoying your new Road Glide iPhone / GPS Mount!
About Chris Trausch
View all posts by Chris Trausch →
← The Adventures of Indiana Joe – Issue 32: Ty Vole!
http://blog.ironacesspeedshop.com/how-to/how-to-install-a-road-glide-iphone-gps-mount/[4/14/2014 3:28:19 PM]
How To: Install a Road Glide iPhone / GPS Mount | Iron Aces Speed Shop
The Adventures of Indiana Joe – Issue 33: Pekelne Doly →
Leave a Reply
NAME (REQUIRED)
EMAIL (REQUIRED)
WEBSITE
COMMENT
Submit Comment
Search
LATEST POPULAR COMMENTS TAGS
The Adventures of Indiana Joe – Issue 37: Rocks
April 2, 2014
The Adventures of Indiana Joe – Issue 36: Speedway
January 23, 2014
The Adventures of Indiana Joe – Issue 35: Johnson’s
October 18, 2013
How To: Install a Street Glide iPhone / GPS Mount
http://blog.ironacesspeedshop.com/how-to/how-to-install-a-road-glide-iphone-gps-mount/[4/14/2014 3:28:19 PM]
How To: Install a Road Glide iPhone / GPS Mount | Iron Aces Speed Shop
October 16, 2013
The Adventures of Indiana Joe – Issue 34: Détenice
September 4, 2013
CATEGORIES
Adventures of Indiana Joe (37)
Audio (3)
Exhaust (1)
How To (8)
Just Because (2)
License Plate (1)
Lighting (2)
Suspension (1)
FOLLOW US ON TWITTER
Potato Soup - Issue 037 - http://t.co/qkskCpbwBh 2 weeks ago
Cool things about to come out from our friends over @maiercarbon #carbonfiber #charlesmaier http://t.co/5aFgm0gDur 1
month ago
Save BIG on the Jac-Knife Highway Pegs… http://t.co/Rd9DMDAc1J 1 month ago
Potato Soup - Issue 037 - http://t.co/a9VRTIeJ5A 2 months ago
RT @Calico_Coatings: People don't "like" @ironaces they LOVE @ironaces check these guys out! 2 months ago retweeted
via Calico_Coatings
Follow ironaces on Twitter
http://blog.ironacesspeedshop.com/how-to/how-to-install-a-road-glide-iphone-gps-mount/[4/14/2014 3:28:19 PM]
How To: Install a Road Glide iPhone / GPS Mount | Iron Aces Speed Shop
READ ALL OF THE ADVENTURES…
The Adventures of Indiana Joe – Issue 01: Survival
The Adventures of Indiana Joe – Issue 02: Bosco
The Adventures of Indiana Joe – Issue 03: Heorot
The Adventures of Indiana Joe – Issue 04: Ortega
The Adventures of Indiana Joe – Issue 05: Eureka
The Adventures of Indiana Joe – Issue 06: Roswell
The Adventures of Indiana Joe – Issue 07: Odds
The Adventures of Indiana Joe – Issue 08: Zehm
The Adventures of Indiana Joe – Issue 09: Noble
The Adventures of Indiana Joe – Issue 10: Coronato
The Adventures of Indiana Joe – Issue 11: Hope
The Adventures of Indiana Joe – Issue 12: Loneliness
The Adventures of Indiana Joe – Issue 13: Friendship
The Adventures of Indiana Joe – Issue 14: Truth
The Adventures of Indiana Joe – Issue 15: Sturgis
The Adventures of Indiana Joe – Issue 16: Fear
The Adventures of Indiana Joe – Issue 17: Massadona
The Adventures of Indiana Joe – Issue 18: Cowboy
The Adventures of Indiana Joe – Issue 19: Cody
The Adventures of Indiana Joe – Issue 20: Lessons
The Adventures of Indiana Joe – Issue 21: Rain
The Adventures of Indiana Joe – Issue 22: Nostalgia
The Adventures of Indiana Joe – Issue 23: Oatman
The Adventures of Indiana Joe – Issue 24: Laughlin
The Adventures of Indiana Joe – Issue 25: B25
The Adventures of Indiana Joe – Issue 26: Crocker
The Adventures of Indiana Joe – Issue 27: Respect
The Adventures of Indiana Joe – Issue 28: Decisions
The Adventures of Indiana Joe – Issue 29: Iowa
The Adventures of Indiana Joe – Issue 30: Europe
The Adventures of Indiana Joe – Issue 31: Bones
The Adventures of Indiana Joe – Issue 32: Ty Vole!
The Adventures of Indiana Joe – Issue 33: Pekelne Doly
The Adventures of Indiana Joe – Issue 34: Détenice
The Adventures of Indiana Joe – Issue 35: Johnson’s
The Adventures of Indiana Joe – Issue 36: Speedway
The Adventures of Indiana Joe – Issue 37: Rocks
http://blog.ironacesspeedshop.com/how-to/how-to-install-a-road-glide-iphone-gps-mount/[4/14/2014 3:28:19 PM]
How To: Install a Road Glide iPhone / GPS Mount | Iron Aces Speed Shop
ABOUT US
Founded by Chris and Lindsey Trausch, Iron Aces Speed Shop is an online store specializing in niche HarleyDavidson aftermarket parts and accessories for touring models. It's our goal not to necessarily be the end all, be all in
the touring market but instead keep our focus on niche Harley touring products.
SUBSCRIBE
Stay in the loop by subscribing to our Potato Soup Newsletter. You can also get live notifications as new postings are
added by adding our RSS feed to your favorite reader.
E-mail
Submit

PAGES
Home
Blog
Shop
Road Glide Mount
Iron Aces Speed Shop © 2014. All Rights Reserved.
(704) 255-1780
http://blog.ironacesspeedshop.com/how-to/how-to-install-a-road-glide-iphone-gps-mount/[4/14/2014 3:28:19 PM]