XTN-SERIES RADIO "HOW TO" SHEET
XTN-SERIES RADIO "HOW TO" SHEET
TO RESET TO FACTORY SETTINGS
• Turn radio OFF
• PRESS & HOLD PTT BUTTON &
TO RESET
While turning radio ON (hold for several seconds) radio will tone
Indicator Light
Use
(Power) to:
Turn power On/Off
Adjust radio volume
TO PROGRAM FREQUENCIES AND CODES
• Turn radio OFF
PTT &
• PRESS & HOLD PTT
BUTTON WHILE TURNING RADIO ON
(HOLD FOR SEVERAL SECONDS, RADIO WILL BEEP & "PROG"will be displayed)
• Press
or
to select channel to program (on a multi-channel radio)
• Press
(FREQ number will flash)
• Choose desired frequency by pressing
or
• Press
to lock in frequency & to advance to the next step of
programming the interference eliminator code
• Choose desired code by pressing
or
(0 is open squelch / code off)
• Press
to lock in code & to advance to the next step of
programming the scramble code (on 2 watt models only)
• Choose desired code by pressing
or
Accessory Jack:
Radio Plug-in Charging
Audio Accessories
P
Use TT to:
Talk/Exit a menu
Use
to:
Transmit Call Tone
(choice of 1,2,3 or 0 MEANS NO SCRAMBLE CODE IS ON)
• Press
to lock in scramble code & to advance to the next step
of programming Hi or Lo bandwidth
• Choose desired bandwidth by pressing
or
• Press
to lock in bandwidth & to advance to next step of
programming manager lockout
• Choose (Y)ES or (N)O by pressing
or
PTT BUTTON
• Exit programming mode by PRESSING & HOLDING PTT
FOR SEVERAL SECONDS
Use
to:
Channel Preset #1
Use
to:
Turn Scan On/Off
Monitor the Frequencies
Use
to:
Scroll through menus
Lock the keypad
Use
to:
Channel Preset #2
Use
and
to:
Change Channels
Change menu settings
Speaker
Microphone
TO ENABLE VOX WITH COMPATIBLE ACCESSORIES
AUDIO QUALITY OF XTN NOT CRISP WHEN USED WITH
Turn radio OFF
Firmly push accessory plug into accessory jack, making sure
that it is fitted into place
Turn radio ON (A flashing face will appear to show that the accessoy is VOX capable)
Press
("CA" will appear)
SPIRIT M-SERIES
Press MENU (A solid face and an "E" will appear to show that an external accessory
to select setting.
If XTN audio quality is not clear when using along with Spirit M-Series.
In XTN program mode press
to advance to bandwidth
setting.
Display shows lower case "b" and "Hi" or "Lo". Use
or
is plugged into the radio)
Press +
or -
to increase or decrease VOX sensitivity (0 is off,
1 is the lowest sensitivity, 3 is the highest sensitivity)
Press
Frequencies 1, 2, 5, 6, 7, 8
M-Series Bandwidth - Hi
Press
XTN Series Bandwidth - Hi / Lo (selectable)
TO ASSIGN CHANNELS TO PRESET BUTTONS ON XV2600
or XU2600 MODELS ONLY
When first entering programming mode, channel number will flash
By pressing
or
the channel number will be increased or
decreased
Select a channel by pressing
or
PRESS & HOLD PRESET 1 ( ) or PRESET 2 ( ) BUTTON
UNTIL IT LOCKS IN
Exit programming mode by PRESSING & HOLDING PTT
FOR SEVERAL SECONDS
Press SCAN (button with
PTT
Frequencies 3 & 4
M-Series Bandwidth - Lo
XTN Series Bandwidth - Lo
TO TURN ROGER BEEP ON
Turn radio OFF
HOLD
WHILE TURNING RADIO ON
Repeat to deactivate feature.
TO REMOVE DELAY - 1st WORDS LOST
(RADIO IN BATTERY SAVER MODE)
Turn radio OFF
TO SCAN
Press
UHF - Bandwidth Settings:
on it)
to transmit on channel where activity is found
Press and HOLD
PTT
&
&
while turning the radio on
until 3 Trumpet type tones indicate feature has been turned off.
If problems are not solved, please call ACS at 800-248-5391
for support.
Business Two-Way Radios
647 Blackhawk Drive Westmont, IL 60559 Phone: 800-248-5391 Fax 800-939-5391
© Copyright 2024