1. No category

Question: 1
What is a recommended step after an EML E-Series library is first initialized during installation?
A. Perform a manual calibration cycle from the front panel.
B. Move a cartridge to one of the slots in the lowest usable row.
C. Run the demo test from the front panel for at least 10 loop cycles.
D. Move a cartridge into the lowest usable tape drive and perform an unload from the front panel.
Answer: B
Question: 2
Click the Exhibit button. What is the minimum version of IBM Tivoli Storage Manager required to
support ESL E-Series library operations?
A. 5.1
B. 5.2
C. 5.3
D. 5.4
Answer: B
Question: 3
Which type of backup is recommended for data file sizes less than 64KB?
A. image
B. snapshot
C. file-by-file
D. direct access
Answer: A
Question: 4
Using one backup software environment, you want to share tape devices in EML libraries by
allowing two different hosts exclusive access to different tape devices (LUNs). What are possible
methods? (Select two.)
A. Configure zoning on the Fibre Channel switches.
B. Disable the unused tape devices on the Windows hosts.
C. Use persistent binding by editing the driver-specific configuration file on the host.
D. Configure the Network Storage Router mapping table directly over the serial CLI.
E. Purchase a Secure Manager license and use this feature embedded in CommandView TL.
Answer: C, E
Question: 5
How can you resolve an oversubscription in a cascaded fabric with two switches and one interswitch link? (Select two.)
A. Distribute the hosts across the two switches.
B. Modify the Core switch PID format value to 1.
C. Increase the number of switches within the fabric.
D. Increase the number of inter-switch links between the switches.
E. Increase the number of tape drives connected to the tape library.
Answer: A, D
Question: 6
What is the average swap time for cartridges in a single frame ESL E-Series library?
A. 2 to 5 seconds
B. 18 to 20 seconds
C. 60 to 120 seconds
D. 300 to 600 seconds
Answer: B
Question: 7
What must the configuration contain when partitioning an ESL E-Series tape library with
Advanced Secure Manager?
A. at least one drive and one slot
B. two drives, 30 slots, and a mail slot
C. one fully populated drive cluster and 30 slots
D. one Interface Controller and one fully populated cluster
Answer: A
Question: 8
Which HP tool is used to measure sequential performance? (Select two.)
A. IOMETER
B. HP TapePerf
C. HP CreateData
D. HP System Performance
E. Performance Assessment Tool
Answer: B, E
Question: 9
What HP document should you refer to when evaluating performance of an ESL E-Series tape
library and its environment?
A. EBS Design Guide
B. ESL E-Series User Guide
C. Library Tape Tools User Guide
D. Tape and Library Performance Guide
Answer: A
Question: 10
In an ESL E-Series library, what is the recommended maximum number of drives for a 2Gb Fibre
Channel link?
A. 2 SDLT 320
B. 8 SDLT 220
C. 4 Ultrium 230
D. 1 Ultrium 460
Answer: A
Question: 11
If CommandView TL is not available, what can be used to retrieve the log files in the Interface
Manager card of an ESL E-Series tape library?
A. Telnet
B. SNMP
C. Perl scripts
D. anonymous FTP
Answer: D
Question: 12
Which card contains the library event logs of an EML E-Series tape library?
A. Interface Manager
B. Interface Controller
C. library robotics controller
D. Interface Manager memory
Answer: C
Question: 13
What is a consideration when using a UPS with an EML E-Series library?
A. The UPS power must last long enough to finish active backup jobs.
B. The load of the UPS should not exceed 80% of the UPS marked electrical current rating.
C. The UPS must be connected to the Interface Manager serial connector to allow the UPS to
shut down the EML if a power failure occurs.
D. The UPS must be connected to the Interface Controller serial connector to allow the UPS to
stop the tape drives if a power failure occurs.
Answer: B
Question: 14
What is the most critical factor affecting performance at the disk subsystem during a backup?
A. tape feed speed
B. compression ratio
C. disk fragmentation
D. disk connection speed
Answer: C
Question: 15
What are the severity levels for events on EML E-Series tape libraries?
(Select three.)
A. fatal
B. poor
C. critical
D. severe
E. warning
F. information
Answer: C, E, F
Question: 16
What does the Operator Control Panel display when a library hangs because there are more than
100 unlabeled tape cartridges in an ESL E-Series tape library?
A. Error 22
B. Please wait
C. Going on line
D. Inventory failure
Answer: C
Question: 17
You correctly configured an ESL E-Series tape library using CommandView TL and accepted the
default Secure Manager settings. What is the result?
A. Hosts have no access to the library.
B. You are prompted to enter host information.
C. All hosts in the subnet can communicate with the library.
D. Only hosts running HP-UX can communicate with the library.
Answer: A
Question: 18
What is the default Command Line Interface password for the Interface Manager card of an EML
E-Series tape library?
A. root
B. climgr
C. clipwd
D. password
Answer: C
Question: 19
Which port number is required when starting a CommandView TL session?
A. 2301
B. 4095
C. 4444
D. 5555
Answer: B