. Agilent Technologies Taiwan Ltd. Support Solution Unit/E.M.G. 20,Kao-Shuang Road,Ping Chen AGILENT TECHNOLOGIES ISO 9001/17025 INTERNAL ASSESSMENT PROGRAM:EMG E102/1995 Tao-Yuan,Taiwan, R.O.C.886-3-4929666 Cover Sheet Subcontractor Calibration Report Certificate Number: 1-2817852572-1 Manufacturer: Hewlett-Packard Co. Description: Model Number: ET32244 Options Installed: Serial Number: 505016 Customer Asset No.: Customer: ET Special Electronic Test Equipment ET32244-505016 Location of Calibration: Agilent Technologies Taiwan Ltd EPSG SUpport Operation 324 PING CHEN 10090 Foothills Blvd. 20 Kao Shuang Rd Roseville,CA. 95747 Taiwan (800)403-0801 Procedure: #1 Date of Calibration: 8 Dec 2010 Customer PO Number: Temperature: 18 Humidity: 20 This calibration certificate documents that the instrument was calibrated by an Agilent Technologies approved subcontractor for the parameters and at the points specified in the attached calibration certificate or report. Please refer to this attachment for statements regarding calibration procedure and traceability. NOTE:This page is NOT a calibration certificate. Its sole purpose is to present a core set of information from the attached certificate or report in a format similar to Agilent Technologies own calibration certificate. Note: This calibration certificate may reference instruments manufactured by HP and Agilent as being manufactured by Agilent Technologies, Inc. As Received Conditions: Initial testing found the instrument to be IN-SPECIFICATION for the parameters tested. No adjustment was necessary to ensure the performance to published operating specifications. As Shipped Conditions: At the completion of the service, measured values were IN-SPECIFICATION for the parameters tested. Based on the manufacturer recommended calibration interval or user defined calibration interval, the next calibration is due on 8 Dec 2011. The user should determine the suitability of this instrument for its intended use. The results of the performance tests are retained for a period of six years. Remarks or Special Requirements: Issue date: 14 Dec 2010 Chen Chin-Ming Approved - LAB Head Page ver:E.00.00 1 of 1 . EMG Support Operation 10090 Foothills Blvd. Roseville, CA. 95747 AGILENT TECHNOLOGIES INTERNAL ASSESSMENT PROGRAM : EMG E102/1995 (800) 829-4444 Certificate of Calibration Standards Lab Calibration Certificate Number: 1-2817852617-1 Manufacturer: Hewlett-Packard Co. Description: Model Number: ET32244 Options Installed: Serial Number: 505016 Customer Asset No: Customer: Calibration Cert 1920.01 ET Special Electronic Test Equipment Location of Calibration: Agilent Technologies Taiwan Ltd EMG Support Operation 324 PING CHEN 10090 Foothills Blvd. 20 Kao Shuang Rd Roseville, CA. 95747 D400 Service Center - W31 (800) 829-4444 Taiwan Procedure: #1 Date of Calibration: 8 Dec 2010 Customer PO Number: Temperature: (23 +/- 1) °C Humidity: (45 +/- 10)% RH This certifies that this product has been calibrated in accordance with a quality system registered to ISO9001:2008 and accredited to ISO/IEC 17025:2005 and ANSI/NCSL Z540.3-2006 using applicable Agilent Technologies procedures. As Received Conditions: Initial testing found the equipment to be IN-SPECIFICATION at the points tested. As Shipped Conditions: At the completion of the calibration, measured values were IN-SPECIFICATION at the points tested. Remarks or Special Requirements: Reported uncertainties are calculated at a 95% confidence interval with a coverage factor of 2 (k=2). When not specifically called out in the measurement report, a Test Uncertainty Ratio (TUR) of 4:1 and k=2 can be assumed. The test limits stated in the report correspond to the published specifications of the equipment, at the points tested. Print Date: 9 Dec 2010 Larry Goins Engineering Manager Page ver:E.00.00 1 of 2 . EMG Support Operation 10090 Foothills Blvd. Roseville, CA. 95747 AGILENT TECHNOLOGIES INTERNAL ASSESSMENT PROGRAM : EMG E102/1995 (800) 829-4444 Certificate of Calibration Standards Lab Calibration Certificate Number: 1-2817852617-1 Calibration Cert 1920.01 Traceability Information: Technician ID Number: 259522 Traceability is to national standards administered by the U.S. NIST, NRC Canada, Euromet members (NPL, PTB, BNM, etc.) or other recognized standards laboratories. Some measurements are traceable to natural physical constants, consensus standards or ratio type measurements. Supporting documentation relative to traceability is available for review by appointment. This certificate shall not be reproduced, except in full, without prior written approval of the laboratory. This calibration report is composed of a certificate of calibration, performance test results and/or certificate appendices. Each report section may be numbered separately. Calibration Equipment Used: Model Number: 4200 73 Model Description: Trace Number: Datron 4200 Precision Ratio Transformer SP12516 SP12517 Page ver:E.00.00 2 of 2 Cal Due Date: 2 Nov 2011 9 Feb 2012 Certificate Number: 1-2754237446-1 1-2518208933-1