North America Catalogue 3PrePrPreassembled 1. Framo 80 2. Pressix CC 41 3. Accessories 4. Pipe Clamps & Accessories 5. Pipe Guides & Slide Elements Contacts 3PrePrPreassembled Sikla UK Limited 4 Canons Road Canons Industrial Park Milton Keynes MK12 5TL United Kingdom Your Distributor: UCC Industries International Inc. 895 Sandy Beach Road Units 12 & 13 Pickering, Ontario L1W 3N7 Canada Tel. + 44 (0)1908 227 406 Fax + 44 (0)1908 220 968 e-mail: [email protected] Web: www.sikla.co.uk Tel. + 1 (905) 831 7724 Fax + 1 (905) 831 5872 e-mail: [email protected] Web: www.ucci.ca With our network of branches and partner companies inside and outside European market we ensure a comperhensive customer addistance in terms of both national and international projects. Notes 3PrePrPreassembled Our service staff and application engineers will be pleased to offer you their assistance to answer your questions or to work out in cooperation with you specific solutions with the aid of our own planning software. Unless otherwise stated, all load parameters refer to mainly dead static loads at ambient temperature. The indicated permissible loads should be regarded as nominal or working loads and unless otherwise denoted, refer to main direction of the respective load; ultimate load values are not indicated. This catalogue may be used by the recipient only. Each part of the catalogue constitutes the property of Sikla UK Limited. All technical representations as well as data are given to the best of our knowledge. All representations and drawings are nonbinding. We do not assume any liability whatsoever for typographical mistakes or deficiencies Modofications and constructional corrections arising particulary from technological development accepted. Disclaimer: Every effort has been made to ensure that the conversion between metric measures to imperial measures has been carried out accurately by the authors of this publication. Both the product manufacturers , distributors and publishers of the source documentation from which these coversions have been made, accept no responsibility for the figures provided nor the use to which they are put. Sikla Metric catalogues are available upon request to UCCI. Any errors discovered should be notified to UCCI immediately at www.ucci.ca. Sikla 2009 All rights reserved Framo 80 02/2009 4Framo 80 Beam Section TP F 80 Cantilever Bracket AK F 80 Beam Bracket TKO F 80 Page 1-2 Page 1-3 Page 1-4 End Support STA F 80 End Support WBD F 80 Channel Adapter SA F 80 Page 1-5 Page 1-6 Page 1-7 Self Tapping Screw FLS F 80 U-Holder SB F 80 End Cap ADK F 80 Page 1-8 Page 1-9 Page 1-10 Siconnect - Canada 1-1 Framo 80 Beam Section TP F 80 Group: A410 Application Multi-function beam profile for horizontal, vertical and 3-D support structures in a wide variety of building and industrial applications. In addition to the high torsional resistance achieved using a totally closed profile, structural elements and pipe supports can be attached on all 4 sides with virtually no placement restrictions. Specifically designed fixing holes combined with special FLS self-tapping screws ensure precise component placement and secure form-locked fixings. Technical Data Type TP F 80 Section modulus Moment of inertia Radius of inertia [in3 ] [in4 ] [in] 6.25 Ly: 24.99 lz: 24.99 Iy: 1.19 iz: 1.19 Torsional moment lt [in4 ] Cross section A [in2 ] 31.50 2.74 For all values the effect of holes and perforations have been taken into account. Material: Steel, hcp Approvals MPA approved Weight [lb/ft] Qty./ [ft] TP F 80 4.23 20 Part number 192539 02/2009 Siconnect - Canada 1-2 Type Framo 80 Cantilever Bracket AK F 80 Group: A420 Application Ready-to-use element for mounting to Beam Section F 80 and Beam Bracket TKO F 80 or for construction of cross bars with respective connecting element. Configuration With pre-assembled End Cap ADK F 80 Installation Interlocking connection to Beam Section F 80 by means of 4 Formlock bolts. Technical Data Type AK F 80-400 AK F 80-800 Configuration: Material: Plate Beam section L [in] Dimensions of base plate [in] 15 3/4 31 1/2 7 1/2 x 3 1/8 x 5/16 7 1/2 x 3 1/8 x 5/16 Slots in base plate for [in] 3 /8 /8 3 Plate welded to Beam section F 80 Steel, hcp Steel, hcp Approvals MPA approved Type 02/2009 AK F 80-400 AK F 80-800 W [lb] Quantity/ pack 7.55 12.88 1 1 Part number 192764 192771 Siconnect - Canada 1-3 Framo 80 Beam Bracket TKO F 80 Group: A423 Application Ready-to-use element for mounting to walls, floors, and ceilings as well as to Simotec Systems 100 and 120 or for assembling crossbars with the respective connecting element. Configuration With pre-assembled End Cap ADK F 80. Installation Depending on the situation, different options are recommended: a) Fixing to building structure using 4 heavy duty anchors 1/2". b) Frictional connection to steel beams (flange width 3 1/8" - 4 3/4") with Assembly Set P2. c) Interlocking connection to beams of System 100 or 120 by means of Bracket Plates FV 100/120. Technical Data Type TKO F80-400 TKO F80-800 Configuration Material: Base plate Beam section L [in] Dimensions of base plate [in] 15 3/4 31 1/2 8 5 /8 x 8 5 /8 x 1 /2 8 5 /8 x 8 5 /8 x 1 /2 Slots in base plate for [in] 1 1 /2 /2 Base plate welded to Beam Section F 80 Steel, hcp Steel, hcp Approvals MPA approved TKO F 80-400 TKO F 80-800 Siconnect - Canada 1-4 W [lb] Quantity/ pack 14.65 20.42 1 1 Part number 192788 192795 02/2009 Type Framo 80 End Support STA F 80 Group: A422 Application In connection with Beam Bracket, Cantilever Bracket or Beam Section F 80, the End Support STA F 80 enables the construction of crossbars, as well as further constructions. The Version "A" is specially conceived for direct connection to cast-in channels built into the building structure. STA F 80 Installation Depending on the version, following mountings solutions are possible: a) Connection to Beam section F 80 with system elements by means of 4 Formlock bolts F 80. b) Screw connection with cast-in channel by means of appropriate T-head bolt or Channel nut with Hexagon bolt (Type "A"). Technical Data Type Dimensions of Base plate [in] STA F 80 STA F 80-E STA F 80-A STA F 80-E 1 1 Slots in base plate for [in] 5 3 7 /2 x 3 /8 x /16 7 1/2 x 3 1/8 x 5/16 7 1/2 x 3 1/8 x 5/16 Configuration: Material: Plate Octagonal element /8 /8 1 /2 3 Base plate welded to octagonal element F 80 Steel, hcp Steel, hcp Approvals MPA approved Type STA F 80 STA F 80-E STA F 80-A W [lb] Quantity/ pack 3.55 3.33 3.77 1 1 1 Part number 192856 192863 192870 02/2009 STA F 80-A Siconnect - Canada 1-5 Framo 80 End Support WBD F 80 Group: A421 Application End Support WBD F 80 is ideal for making supports for wall and floor mounting, as well as crossbars in conjunction with Beam section F 80. Beside the direct connection to building structure, different base plates allow an immediate connection to various flange widths. For crossbar constructions, version WBD F 80-T has to be used. The octagonal connection allows max. use of section width without interfering screws or plates. Installation Depending on the situation, different options are recommended: a) Fixing to building structure using 4 heavy-duty 1/2" anchors resp. 5/8". b) Frictional connection to steel beams using Assembly Set P2, P3 or respective Beam clip. c) Form-locking connection to beam systems STF 100 or 120 using Bracket Plates FV 100/ 120. Technical Data Type WBD F 80-80/120 WBD F 80-121/160 WBD F 80-161/200 WBD F 80-201/300 WBD F 80-T for flange width [in] 3 1 /8 – 4 3 /4 4 3 /4 – 6 1 /4 6 1 /4 – 7 7 /8 7 7/8 – 11 3/4 3 1 /8 – 4 3 /4 Configuration: Material: Plate Square F 80 Octagonal element F 80 Dimensions of base plate [in] Slots in base plate for [in] 8 5 /8 x 8 5 /8 x 1 /2 14 3/16 x 10 1/4 x 1/2 14 3/16 x 12 1/4 x 1/2 16 1/2 x 8 5/8 x 1/2 8 5 /8 x 8 5 /8 x 1 /2 1 /2 /2 5 /8 5 /8 1 /2 1 Base plate welded to square F 80 resp. octagonal element F 80 Steel, hot-dipped galvanised Steel, hot-dipped galvanised Steel, hot-dipped galvanised Approvals MPA approved WBD F 80-T Siconnect - Canada 1-6 WBD F 80-80/120 WBD F 80-121/160 WBD F 80-161/200 WBD F 80-201/300 WBD F 80-T W [lb] Quantity/ pack 11.54 19.31 22.64 20.87 10.66 1 1 1 1 1 Part number 192801 192818 192825 192832 192849 02/2009 Type Framo 80 Channel Adapter SA F 80 Group: A430 Application Allows the compatibility of Sikla channels 1 5/8" x 1 5/8" or 1 5/8" x 1 5/8" D with Beam Section F 80. Simple construction of pipe lines or constructions, optionally with further parts of the Siconnect System. Thanks to the Pressix CCTechnology the channel can be connected directly to the Channel Adapter. Installation Interlocking connection to Beam Section F 80 by using 4 self-tapping screws F 80. Technical Data Type Dimension of base plate Slots in base plate [in] [in] SA F 80-41 Configuration: Material: Plate U-Profile Type 02/2009 SA F 80-41 3 7 1/2 x 3 1/8 x 5/16 /8 Base plate welded to U-profile Steel, hot-dipped galvanised Steel, hot-dipped galvanised W [lb] Quantity/ pack 3.11 1 Part number 192887 Siconnect - Canada 1-7 Framo 80 Self Tapping Screw FLS F 80 Group: A430 Application Threaded self-tapping screw for formlocking connection of Framo system components and Siconnect products to Beam Section F 80. The beam section material is locally cold-hardened due to the non-cutting forming. The high resulting edge-covering and a threaded connection between self-tapping screw and beam section prevents from accidental unscrewing. During assembly process, the special interlocking prevents from overwinding. Technical Data Type Tightening torque [ft/lbs] FLS F 80 Material: 44.25 Steel, HCP Approvals MPA tested FLS F 80 Siconnect - Canada 1-8 W [lb] Quantity/ pack 0.04 100 Part number 192512 02/2009 Type Framo 80 U-Holder SB F 80 Group: A430 Application Connecting element for bilateral fixation of Beam section F 80, crossbars or cantilevers to steel beams. SB F 80-16 Configuration Type SB F 80-16: Holder with thread 3/8" Plate 2 Hexagon nuts 3/8" 2 Washers Type SB F 80-40: Holder with thread 1/2" Plate 2 Beam Clips P2 2 Hexagon nuts 1/2" 2 Washers Installation U-holder to be used in pairs. Type 16 up to flange width 5/8" Type 40 up to flange width 1 9/16" Technical Data Material: U-Holder Steel, hot-dipped galvanised Plate Steel, hot-dipped galvanised Beam clip Steel resp. Cast Iron, hot-dipped galvanised Nut/Washer Steel, hot-dipped galvanised Type SB F 80-16 SB F 80-40 W [lb] Quantity/ pack 1.33 3.33 20 10 Part number 192683 194010 02/2009 SB F 80-40 Siconnect - Canada 1-9 Framo 80 End Cap ADK F 80 Group: A430 Application End cap for tidy closing the ends of Beam section F 80, Cantilever brackets, as well as Beam Brackets. Technical Data Material: PP, yellow ADK F 80 Siconnect - Canada 1-10 W [lb] Quantity/ pack 0.04 25 Part number 192674 02/2009 Type Pressix CC 41 - Channel System 02/2009 3Pressix CC 41 - Channel System Channel MS 41 End Cap ADK 41 End Support WBD Page 2-3 Page 2-10 Page 2-11 Clamping Unit KL Channel Connector SK Clamping End SKL Page 2-13 Page 2-14 Page 2-15 Corner Bracket EW Fitting Set MOS CC Angle Connector CN CC 41 Stabil Page 2-16 Page 2-17 Page 2-18 Angle Connector CN CC 41-2 Blockset PBS CC 41 Speed Nut NT CC 41 Page 2-19 Page 2-20 Page 2-21 Siconnect - Canada 2-1 Pressix CC 41 - Channel System Holding Bracket HK 41 Siconnect - Canada 2-2 02/2009 Page 2-22 Pressix CC 41 - Channel System Channel MS 41 Group: 1111 Application Element for easily and efficiently pre-assembling crossbars, wall brackets and support structures on site or in workshops. Configuration Double channels are joined together by clinching, guaranteeing corrosion protection at the joining. 41/21/2,0 Installation If required, channels can be joined on site using: Slot pattern II: - Hexagon socket bolt 5/16" x 5/8", with a max. spacing of 9.85" between connecting points one point at each end. Slot pattern III and IV: - Clamping Unit KL (for details see product). All channels 41 are serrated on the inner edges and thus can be combined with many other Sikla products, e.g. Channel Nut, End Support WBD, Beam Clamp TCS 1. Particularly effective combinations are possible using other Pressix components. All 41-types except of 1 5/8 x 1 5/8 x, 12 gauge D can be used as guide and support channels by inserting Slide Block 41 inside the channel. 41/41/2.5 Technical Data Material: Cold-worked steel strip 1.0305, pre-galvanised according to DIN EN 10327 For further data, please refer to the following pages. D= Double channel Type [in] 41-75/75/3.0 Length [ft] Weight [lbs/ft] Qty./ [ft] Part number 1 5/8 x 13/16 x 16 gauge 1 5/8 x 13/16 x 14 gauge 1 5/8 x 1 5/8 x 14 gauge 1 5/8 x 1 5/8 x 12 gauge 1 5/8 x 3 x 3 x 11 gauge 20 20 20 20 20 0.75 0.88 1.31 1.53 3.60 20 20 20 20 20 173846 193709 193747 166720 173999 1 5/8 x 13/16 x 14 gauge D 1 5/8 x 1 5/8 x 14 gauge D 1 5/8 x 1 5/8 x 12 gauge D 1 5/8 x 3 x 3 x 11 gauge D 20 20 20 20 1.76 2.62 3.06 7.20 20 20 20 20 193815 193822 166757 174161 Sikla offer all channel profiles and threaded rod cut to requested lenght. This service is offered at no additional cost. 02/2009 41/42/2.5 D Siconnect - Canada 2-3 Pressix CC 41 - Channel System Channel MS 41 - Technical Data Group: 1111 Type W/H/Th [in] 1 5/8 x 13/16, 16 ga 1 5/8 x 13/16, 14 ga 1 5/8 x 1 5/8, 14 ga 1 5/8 x 1 5/8, 12 ga 1 5/8 x 3 x 3, 11 ga 1 5/8 x 13/16, 14 ga D 1 5/8 x 1 5/8, 14 ga D 1 5/8 x 1 5/8, 12 ga D 1 5/8 x 3 x 3, 11 ga D Section modulus [in3 ] Moment of inertia [in4 ] Ly : 0.311 lz : 1.386 Ly : 0.362 lz : 1.713 Ly : 2.031 lz : 2.945 Ly : 2.437 lz : 3.563 Ly : 17.484 lz : 17.118 Ly : 1.941 lz : 3.425 Ly : 11.551 lz : 5.890 Ly : 14.563 lz : 7.126 Ly : 90.710 lz : 34.236 Wy : 0.284 Wz : 0.677 Wy : 0.324 Wz : 0.835 Wy : 0.957 Wz : 1.437 Wy : 1.165 Wz : 1.736 Wy : 4.060 Wz : 4.563 Wy : 0.925 Wz : 1.669 Wy : 2.819 Wz : 2.874 Wy : 3.551 Wz : 3.472 Wy : 12.095 Wz : 9.083 Radius of gyration [in] Iy : 0.311 iz : 0.654 Iy : 0.299 iz : 0.650 Iy : 0.575 iz : 0.689 Iy : 0.563 iz : 0.677 Iy : 0.996 iz : 0.984 Iy : 0.488 iz : 0.650 Iy : 0.965 iz : 0.689 Iy : 0.969 iz : 0.677 Iy : 1.602 iz : 0.984 ga= gauge Type W/H/Th [in] 1 5/8 x 13/16, 16 ga 1 5/8 x 13/16, 14 ga 1 5/8 x 1 5/8, 14 ga 1 5/8 x 1 5/8, 12 ga 1 5/8 x 3 x 3, 11 ga 1 5/8 x 13/16, 14 ga D 1 5/8 x 1 5/8, 14 ga D 1 5/8 x 1 5/8, 12 ga D 1 5/8 x 3 x 3, 11 ga D Max. torsional Moment Mq Cross section A [in2 ] Distance e [in] Max. point carrying moment Fmax (tension) [lb] Max. torsional moment Mq [in/lb] 0.51 0.64 0.96 1.20 2.74 1.26 1.92 2.40 5.47 0.44 0.44 0.84 0.82 1.70 0.83 1.61 1.61 2.95 450 900 900 1350 2250 900* 900* 1350* 2250* 394 394 394 394 394 394 394 394 394 D = Double channel * Double channels with max. length up to 19 5/8" should be connected at both ends, if bearing and point of load incidence are not on the same side: Slot pattern 2: with Hexagon socket screw 5/16" x 5/8" Slot pattern 3 or 4: by means of Clamping Unit KL 1. Siconnect - Canada 2-4 02/2009 All values in both tables refer to slotted channels. Pressix CC 41 - Channel System Channel MS 1 5/8 x 13/16 x 16 gauge 1 5/8 x 13/16 x 16 gauge Slot pattern II The influence of the channel slots and the channel's dead weight are taken into account in the values. 41/21/1.5 02/2009 σperm ≤ 160 N/mm2 f ≤ L/200 Siconnect - Canada 2-5 Pressix CC 41 - Channel System Channel MS 1 5/8 x 13/16 x 14 gauge 1 5/8 x 13/16 x 14 gauge Slot pattern III 1 5/8 x 13/16 x 14 gauge D 41/21/2.0 41/21/2.0 D The influence of the channel slots and the channel's dead weight are taken into account in the values. Siconnect - Canada 2-6 02/2009 σperm ≤ 160 N/mm2 f ≤ L/200 Pressix CC 41 - Channel System Channel MS 1 5/8 x 1 5/8 x 14 gauge 1 5/8 x 1 5/8 x 14 gauge Slot pattern III 41/41/2.0 1 5/8 x 1 5/8 x 14 gauge D 41/41/2.0 D The influence of the channel slots and the channel's dead weight are taken into account in the values. 02/2009 σperm ≤ 160 N/mm2 f ≤ L/200 Siconnect - Canada 2-7 Pressix CC 41 - Channel System Channel MS 1 5/8 x 1 5/8 x 12 gauge 1 5/8 x 1 5/8 x 12 gauge Slot pattern III 41/41/2.5 1 5/8 x 1 5/8 x 12 gauge D The influence of the channel slots and the channel's dead weight are taken into account in the values. σperm ≤ 160 N/mm2 f ≤ L/200 Siconnect - Canada 2-8 02/2009 41/41/2.5 D Pressix CC 41 - Channel System Channel MS 1 5/8 x 3 x 3 x 11 gauge 1 5/8 x 3 x 3 x 11 gauge Slot pattern IV 41-75/75/3.0 1 5/8 x 3 x 3 x 11 gauge D The influence of the channel slots and the channel's dead weight are taken into account in the values. σperm ≤ 160 N/mm2 f ≤ L/200 02/2009 41-75/75/3.0 D Siconnect - Canada 2-9 Pressix CC 41 - Channel System End Cap ADK 41 Group: 1304 Application To be used for safely and neatly covering the ends of Sikla Channels. Double channels require 2 End Caps. Technical Data Material: HD-PE, yellow Siconnect - Canada 2-10 For channel [in] 1 5/8 x 13/16, 16-12 gauge 1 5/8 x 1 5/8, 14-12 gauge 1 5/8 x 3 x 3, 11 gauge W [lb] Quantity/ pack 0.02 0.02 0.04 100 100 50 Part number 101037 177689 177716 02/2009 Type [in] 1. 1 5/8 x 13/16 1 5 /8 x 1 5 /8 1 5 /8 x 3 x 3 Pressix CC 41 - Channel System End Support WBD Group: 1356 Application In combination with a channel, End Support WBD is particularly suitable for setting up support structures attached to walls, floors and ceilings and in particular as a base for frame structures made of Sikla channels. The generous dimensions and the rhomib shape of the mounting plate provide for a high bending moment and safely stabilise lateral loads. Installation Normally, two bolts grouped opposite to each other and along the load axis are sufficient. Only in exceptional cases (e.g. high props in frameworks) four bolts are required. Minimum torque values for the hexagon bolts of the 41 Holding Brackets are: Types [in] Holding Bracket s [pcs] 1 5/8 x 13/16 up to 1 5/8 x 1 5/8 1 5/8 x 1 3/4 up to 1 5/8 x 3 x 3 1 5/8 x 13/16 D up to 1 5/8 x 1 5/8 D 1 5/8 x 1 3/4 D up to 1 5/8 x 3 x 3 D For single channels Bolt for Holding Bracket [in] 3 1 2 1 1 /8 /2 3 /8 1 /2 1 Accessories Torque [lb] pre-assembled pre-assembled in loose form in loose form 90 135 90 135 For ceiling mounting under high loads (up to 1575 lbs), we recommend the use of at least one fully traversing bolt for connecting the channel to the End Support WBD (for examples see "Installation Guideline"). Technical Data Type [in] 1 5/8 x 13/16 1 5 /8 x 1 5 /8 1 5 /8 x 3 x 3 1 5/8 x 13/16 D 1 5 /8 x 1 5 /8 D 1 5 /8 x 3 x 3 D Suitable for für Sikla channel 1 5/8 x 13/16, 16-14 ga 1 5/8 x 1 5/8, 14-12 ga 1 5/8 x 3 x 3, 11 ga 1 5/8 x 13/16, 16-14 ga D 1 5/8 x 1 5/8, 14-12 ga D 1 5/8 x 3 x 3, 11 ga D A [in] 5 5/16 5 5/16 8 1 /4 5 5/16 8 1 /4 10 s [in] 1 B [in] /4 4 /4 4 5 /16 6 11/16 1 /4 4 5 /16 6 11/16 5 /16 8 1 b [in] 1 1 1 1 1 1 h [in] 7 /16 /16 1 /2 7 /16 1 /2 1 /2 7 C [in] 3 3 /4 3 3 /4 5 5/16 4 15/16 4 15/16 5 5/16 ga = gauge For double channels Working load for Wall mounting: See tables on the following pages. The figures apply on walls if two bolts of the load class as stated are used. Working load for Ceiling Mounting: The permissible maximum vertical load for ceiling mounting structures fixed by way of at least one traversing bolt (blass 8.8) amounts to 1575 lbs. 02/2009 For End Supports WBD for single channels, the following values apply subject to the condition that all included accessories are assembled correctly. Siconnect - Canada 2-11 Pressix CC 41 - Channel System Types [in] Working load (tension) for ceiling mounting [lb] 1 5/8 x 13/16 up to 1 5/8 x 1 5/8 1 5/8 x 2 up to 1 5/8 x 3 x 3 Siconnect - Canada 2-12 Steel, cold-formed, electro-galvanised Type [in] For Sikla Channel [in] 1 5/8 x 13/16 1 5 /8 x 1 5 /8 1 5 /8 x 3 x 3 1 5/8 x 13/16 D 1 5 /8 x 1 5 /8 D 1 5 /8 x 3 x 3 D 1 5/8 x 13/16, 12 gauge 1 5/8 x 1 5/8, 12 gauge 1 5/8 x 3 x 3, 11 gauge 1 5/8 x 13/16, 12 gauge D 1 5/8 x 1 5/8, 12 gauge D 1 5/8 x 3 x 3, 11 gauge D Holding Brackets [number of] W [lb] Quantity / pack 1 1 2 1 1 1 1.88 1.83 4.83 2.51 5.42 9.66 10 10 5 5 5 5 Part number 177725 155054 177752 146469 106768 177779 02/2009 Material 450 900 Pressix CC 41 - Channel System Clamping Unit KL Group: 1357 Application Used for assembling double channels made from Sikla Channels with slot pattern III or IV, i.e. with a minimum material thickness of 1/8". This system could be used be used for pre-assembly in a workshop also. When a torque wrench is required in order to ensure that the static values indicated on page 3-7 (Sikla Online Catalogue) are achieve. Attention: These values are only guaranteed when using Sikla Channels. Configuration Consists of forming plate, pressure plate and a hexagon socket bolt 5/16" (DIN 7991) Installation Max. spacing between connecting points is 19 5/8" mm, with one point at each end of the channel section. Torque: M = 18.5 ft lbs Technical Data Material: Malleable cast iron, electro-galvanised Type For Sikla Channel [in] KL 1 1 5/8 x 13/16, 14 ga up to 1 5/8 x 3 x 3, 11 ga W [lb] Quantity/ pack 0.22 50 Part number 118055 02/2009 ga = gauge Siconnect - Canada 2-13 Pressix CC 41 - Channel System Channel Connector SK Group: 1353 Application Developed for easily and safely joining Sikla Channels on or for pre-assembly in the workshop with a minimum of individual parts. The overall design ensures there is no static weak point near the channel connector when single channels are connected. For single channels, the figures as indicated on page 3-7 (Sikla Online Catalogue) are applicable. SK 41/21 Configuration With 41 Holding Brackets and hexagon nuts (supplied loose). Installation To guarantee the static values, the supplied elements have to be used. For extension of double channels, see advice brochure "Installation Guidelines". Technical Data Material: Malleable iron, electro-galvanised Type [in] For channel [in] Material Overall length [in] W [lb] Quantity/ pack 1.24 1.30 3.55 10 10 10 Part number [in] SK 1 5/8 x 13/16 1 5/8 x 13/16 SK 1 5/8 x 1 5/8 1 5/8 x 1 5/8 SK 1 5/8 x 3 x 3 1 5/8 x 3 x 3 5 /32 5 /32 3 /16 6 5/16 6 5/16 10 1/4 177599 155115 177626 SK 41/41-45 SK 41/52 to 41-75/75 Siconnect - Canada 2-14 02/2009 Application example Pressix CC 41 - Channel System Clamping End SKL Group: 1350 Application Mounting element to be fixed within the flanges of I- and U-shaped beams. The systems (such as pipes, etc.) supported this way may run parallel or at right angles to the direction of the I or U beam. Also suitable as support for crossbars between two vertically adverse arranged profiles. Configuration Pre-assembled Installation The tightening moment of the clamping bolts must be between 1 (minimum) and 1 1/2 (maximum) turns; then tighten locking nuts. Note: The length of the channel to be cut : inside diameter of beam less 1". Technical Data Permissible load per set: Crossbar support: (2 sets) 1125 lbs/crossbar Single attachment: (1 set) 560 lbs The maximal torsional moment of the channel is to be taken into consideration. 02/2009 Material: Cold-worked steel, electro-galvanised Type For Channel size [in] Minimum beam type [in] L [in] SKL 1 5/8 x 1 5/8, 12 gauge IP 5 1/2, U 7 7/8 4 B [in] W [lb] 2 1/2 2.05 Pack. [Set] 5 Part number 145671 Siconnect - Canada 2-15 Pressix CC 41 - Channel System Corner Bracket EW Group: 1352 Application Bracket for assembling crossbars made from channels of type 41: 1 5/8" x 13/16" to 1 5/8" x 1 5/8" (suitable for double channels also) Particularly useful in cases in which the openings of the channels are not facing the crossbars. Particularly useful in cases in which the openings of the channels are not facing the crossbars. The same bracket can be used on both sides of the crossbar; thus easy stockkeeping and no danger of mix-up. Configuration Supplied without bolts and nuts. Installation To be used in pairs. For easy installation, pre-assemble 3 3/8" x 3/4" hexagon bolts with CC-nut 3/8" (use washer for oval hole). This way, the Corner Bracket may be tightened in the channels immediately after insertion. > The cutting length of the crossbar should be clearance minus 10 mm (see drawing) Technical Data Max. perm. working load: 560 lbs centre load per crossbar fixed with 2 EW Corner Brackets 41 Steel electro-galvanised Type EW 41 Siconnect - Canada 2-16 W [lb] Quantity/ pack 0.38 25 Part number 160803 02/2009 Material: Pressix CC 41 - Channel System Fitting Set MOS CC Group: 1330 Application Connecting element for cross bars between two channels. Hint: Per cross bar always two fitting sets have to be used. Configuration Completely pre-assembled. CC - MH 41 Technical Data Material: Steel, electro-galvanised Type For channel [in] Wall plate [in] W [lb] CC - MH 41 1 5/8 x 13/16 – 1 5/8 x 1 5/8 5 5/16 x 1 5/8 x 3/16 0.86 CC - MV 41 1 5/8 x 13/16 – 1 5/8 x 1 5/8 5 5/16 x 1 5/8 x 3/16 0.86 Qty./ pack 10 10 Part number 191756 191765 02/2009 CC - MV 41 Siconnect - Canada 2-17 Pressix CC 41 - Channel System Angle Connector CN CC 41 Stabil Group: 1326 Application Pre-assembled connecting element for frame structures made of channels. Version W suitable for connections to wall, floor or ceiling. High-speed assembly system for 90°- and 45°-structures of channels 41. Locks automatically by pushing down the bolt head and at the same time supports its own weight Secure, form-locking, non-positive connection. Serrated speed nut with clamping bolt 3/8". Ideal shaping and high-strength material for high stiffness. Technical Data Working load FAdvance = 560 lbs per connector Torque 37 lbs Material: Steel, pre-galvanised CC 41-90° Stabil CC 41-90° W Stabil CC 41-45° Stabil CC 41-45° W Stabil Siconnect - Canada 2-18 W [lb] Quantity/ pack 0.51 0.38 0.51 0.38 25 25 25 25 Part number 191675 191684 191882 191891 02/2009 Type Pressix CC 41 - Channel System Angle Connector CN CC 41-2 Group: 1352 Application Pre-assembled connecting element for three-dimensional frame structures, optimised for linking channels of the 41 series at an angle of 90°. Preferably used in combination with 1 5/8" x 1 5/8" square channels. CC 41-2 Version W is used for connection to wall, floor or ceilings. The adjustment for the channel opening could still be chosen. Fast-Technique for 90° joints of channel system 41 Locks automatically when being put in place and supports its own weight. Secure, form-locking, non-positive connection. Serrated Channel Nut with Hexagon Bolt 3/8". Ideal shaping for high stiffness. Technical Data Working load: Fperm = 675 lbs per Connector Torque: 37 lbs Material: Steel, pre-galvanised Type CC 41-2 CC 41-2 W W [lb] Quantity/ pack 1.21 1.00 10 10 Part number 193495 193648 02/2009 CC 41-2 W Siconnect - Canada 2-19 Pressix CC 41 - Channel System Blockset PBS CC 41 Group: 1309 Application Quick-installation element for efficiently mounting pipe clamps and other components to all Sikla Channels of the 41 series (double channels also). Time-saving due to pre-assembled Blockset instead of 4 single parts. Easy height adjustment inside the channel. Grooved rod is retained, thus preventing any accidental unscrewing. The grooves (distance 3 15/16") provide for easy cutting with the Rod Cutter PBC , saw-cutting or finishing is not required. Configuration Blockset completely pre-assembled. Installation Insert the Blockset into the channel; tighten nut - the job is done! Dismounting takes place in reverse order by turning the to the left and exerting light pressure on the grooved rod in channel direction. Technical Data Type [in] 5 3 /16 x ... /8 x ... M [ft lb] FZ [lb] 7 13 740 1010 FZ = permissible traction at the grooved rod > The point carrying capacity of the channel must not be exceeded. Type [in] L [in] W [lb] Quantity/ pack /16 x 1 3/8 /16 x 3 5 /16 x 5 5 /16 x 7 5 /16 x 11 1 3 /8 3 5 7 11 0.14 0.16 0.20 0.22 0.28 25 25 25 25 25 191549 191558 191567 191576 191585 3 1 3 /8 3 5 7 11 0.18 0.20 0.24 0.30 0.40 25 25 25 25 25 191594 191603 191612 191621 191639 5 5 /8 x 1 3 /8 /8 x 3 3 /8 x 5 3 /8 x 7 3 /8 x 11 3 Siconnect - Canada 2-20 Steel, electro-galvanised Part number 02/2009 Material: Pressix CC 41 - Channel System Speed Nut NT CC 41 Group: 1314 Application In particular useful when installing in vertical channels or in places of difficult access. Further advantages: For all Sikla Channels of type 41, independent of the height of the channel. No getting stuck on bolt heads when sliding in the channel. No appearance of settlement after tightening. Configuration Channel Nut and Spring are tightely connected. Installation After inserting the Speed Nut into the channel opening, it is - by exerting slight pressure on it - turned to the right as far as it will go; deinstallation may be effected by following the instructions in reverse order. Installation and deinstallation do not require tools and may be repeated several times. Technical Data Material: Nut Spring washer Steel class 5.6, electro-galvanised Sheet metal spring steel, rustproof, 1.4310 > The load capacity of the channels is also to be taken into account. Type 02/2009 CC 41-1/4" CC 41-5/16" CC 41-3/8" CC 41-1/2" CC 41-5/8" Load capacity (tension) [lb] W [lb] Quantity/ pack 720 1305 1912 2250 2250 0.07 0.07 0.07 0.13 0.13 50 50 50 50 50 Part number 180200 180209 180218 182252 182261 Siconnect - Canada 2-21 Pressix CC 41 - Channel System Holding Bracket HK 41 Group: 1327 Application Safety element for Sikla channels to be used instead of simple washers. The Holding Bracket prevents the edges along the opening of the channels from bending, and ensures optimum load distribution. When loads are imposed along the channels, B 27 Holding Brackets provide additional safety due to embossed teeth, which bite into the channel. Suitable for channels type 41. Technical Data Material: Malleable iron, electro-galvanised Type [in] 1 5 /8 x 3 /8 1 5 /8 x 1 /2 1 5 /8 x 5 /8 Siconnect - Canada 2-22 Suitable for Sikla channels of width [in] 1 5 /8 1 5 /8 1 5 /8 Bore [in] 7 /16 /2 5 /16 1 W [lb] Quantity/ pack 0.14 0.14 0.14 50 50 50 Part number 178247 178256 178265 02/2009 41/... Accessories 02/2009 4Accessories Beam Clamp TCS Universal Joint UG Mounting Plate GPL Page 3-2 Page 3-3 Page 3-4 Siconnect - Canada 3-1 Accessories Beam Clamp TCS Group: 1337 Application Heavy-duty connection element which, in combination with grub screws (5/16" up to 5/8"), are suitable for mounting pipes, ducts and equipments to steel beams (I-, T-, U-and angle steel beams). The combination with a Universal Joint provides for vertically aligned attachment to inclined beams. Can serve as single mounting element for installing crossbars and for fixing cantilever structures. Due to their special base profile, TCS 1 Beam Clamps can also be slid along and retained in the opening of Sikla Channels of the 41 series. Configuration Pre-assembled with clamping bolt and locking nut. Installation Tighten the clamping bolt of the Beam Clamp first by hand, then tighten down with a spanner according to the mounting structures. The hardened point of the clamping bolt will penetrate the comparatively soft material of the beam, ensuring a solid and highly secure connection. Tighten the locking nut for securing the installation. For installation near a cutting edge of a channel, an additional Holding Bracket 41 has to be mounted. Note: Respect relevant mounting instructions! For FM-construction use thread ≥ 3/8" only! Group TCS 0 Technical Data The nominal loads indicated apply to new Beam Clamps fixed to undamaged beam flanges only. Working load: Material: Group TCS 1 Type TCS 0: 785 lbs Type TCS 1: 1125 lbs Type TCS 2: 1912 lbs Body in cast-iron, electro-galvanised and clamping bolts in steel, class 8.8., electro-galvanised Approvals Approved and accepted by VdS and FM for use with stationary fire extinguishing systems. TCS O LC Approval: G4950065 and G4950066 (erected mounting with 3/8" up to a maximum height hmax = 5 29/32" mm and up DN 50 only). For further types and different application fields: G4820023; G4830054; G4800039/ ...45; G4990027. Type TCS 0 LC TCS 0 M8/M8 TCS 0 M8/M10 TCS 1 M10/M8 TCS 1 M10/M10 TCS 1 M10/M12 TCS 2 M12/M12 TCS 2 M12/M16 Connection [fore/aft] [in] Ø 3 /8 /16, 5/16 5 /16, 3/8 3 /8, 5/16 3 /8 , 3 /8 3 /8 , 1 /2 1 /2 , 1 /2 1 /2 , 5 /8 5 Clamping range on parallel flange [in] 11 /16 /8 7 /8 1 1 1 1 1 7 W [lb] Quantity/ pack 0.22 0.31 0.31 0.47 0.47 0.49 0.62 0.60 50 50 50 50 50 50 25 25 Part number 156648 178283 174206 116770 116150 167332 174224 174215 Siconnect - Canada 3-2 02/2009 Group TCS 2 Accessories Universal Joint UG Group: 1342 Application Universal connection for attachment to non-horizontal components. May be fixed directly to building surfaces, Beam Clamps, channels, etc. Typical uses would include easy on-site manufacture of various tie rod assemblies to support brackets, or reinforcement struts for sliding and fixed point applications (UG FP types are specifically designed for assembly for pipe clamp wings for fixed point constructions). Infinitely variable angle adjustment Length and height adjustment via rotation of the grub screw in the threaded pivot head Securely retained threaded pivot head Secure attachment of nut on the adapter plate. Configuration With adapter plate and locking nut. Installation Screw the grub screw completely into the pivot head (visual control). Fix the adjusted angle by tightening the supplied nut against the adapter plate. Technical Data Type left: UG, right: UG FP Working load Adapter plate [lb] Ø DA [in] Nut UG 5/16 UG 3/8 UG 1/2 UG 5/8 1300 1800 2925 2925 7 /16 /16 5 /8 5 /8 Flange nut Flange nut Flange nut Hexagon nut UG FP 1/2 UG FP 5/8 2925 2925 5 Hexagon nut Hexagon nut Material: 7 5 /8 /8 Steel or malleable cast iron, electro-galvanised Approvals VdS Approval G4980055 for types UG 5/16" to UG 5/8". 02/2009 Type Pivot head [in] A [in] B [in] ØD [in] W [lb] Quantity/ pack Part number UG 5/16 UG 3/8 UG 1/2 UG 5/8 5 /16 /8 1 /2 5 /8 1 1 1 5/16 1 5/16 1 9/16 1 9/16 1 15/16 1 15/16 /2 /2 11 /16 11 /16 2 2 2 3 /4 2 3 /4 0.31 0.31 0.82 0.80 50 50 25 25 158057 158066 158075 158084 UG FP 1/2 UG FP 5/8 1 1 5/16 1 5/16 1 15/16 1 15/16 11 2 3 /4 2 3 /4 0.71 0.69 25 25 158093 158109 3 5 /2 /8 1 L [in] 1 11 /16 /16 Siconnect - Canada 3-3 Accessories Mounting Plate GPL Group: 1227 Application For wall, ceiling and floor installation of mounting elements in M&E services. Technical Data Permissible anchor values may restrict the application. Type [in] Normal 5/16 Normal 3/8 Normal R 1/2 Stabil 3/8 Stabil 1/2 Stabil 5/8 Stabil R 1/2 Stabil R 3/4 Stabil R 1 * 330 330 330 675 675 1000 1000 1350 1350 6.50 12.70 18.40 12.70 21.80 51.80 70.00 132.70 258.10 Max. lever arm [in] 5 7 /8 7 7 /8 11 3/4 7 7 /8 11 3/4 11 3/4 13 3/4 17 5/8 19 5/8 Limitation caused by the Mounting Plate or the loading capacity of the grub screw or of the threaded tube. σperm ≤ 160 N/mm2 fperm < 5 mm Calculation of Nm to ft Pounds x 0.7376 Material: Steel, electro-galvanised Type [in] Normal 5/16 Normal 3/8 Normal R 1/2 Stabil 3/8 Stabil 1/2 Stabil 5/8 Stabil R 1/2 Stabil R 3/4 Stabil R 1 Siconnect - Canada 3-4 Max. perm. bending moment** [ft/lb] Dimension LxBxs [in] 3 1 /8 x 1 1 /8 x 1 /8 3 1 /8 x 1 1 /8 x 1 /8 3 1 /8 x 1 1 /8 x 1 /8 4 3/4 x 1 5/8 x 5/32 4 3/4 x 1 5/8 x 5/32 4 3/4 x 1 5/8 x 3/16 4 3/4 x 1 5/8 x 3/16 4 3/4 x 1 5/8 x 3/16 4 3/4 x 1 5/8 x 3/16 Elongated hole d x a [in] 3 /8 x 5 /8 /8 x 5 /8 3 /8 x 5 /8 7 /16 x 1 7 /16 x 1 7 /16 x 1 7 /16 x 1 7 /16 x 1 7 /16 x 1 3 Centre distance l [in] W [lb] Quantity/ pack 2 1 /8 2 1 /8 2 1 /8 3 1 /8 3 1 /8 3 1 /8 3 1 /8 3 1 /8 3 1 /8 0.10 0.12 0.16 0.28 0.30 0.38 0.40 0.40 0.44 50 50 50 50 50 50 50 50 50 Part number 107501 138361 138501 138343 107556 138352 138529 138538 107592 02/2009 * Working load (tension) [lb] Pipe Clamps & Accessories 1Pipe Clamps & Accessories Stabil D-3G Countersink Screw SCR Triple Thread Connecting Nut NT 3G Page 4-2 Page 4-4 Page 4-4 Adapter AD f/f Height Adjuster HRS 0 Height Adjuster HRS 1 Page 4-5 Page 4-6 Page 4-6 Height Adjuster HRS P 02/2009 Page 4-7 Siconnect - Canada 4-1 Pipe Clamps & Accessories Stabil D-3G Group: 1240 Application For the installation of pipes required for all M&E services in industrial, residential and public buildings. 15 - 72 mm Configuration Sizes 3/8" to 5" are equipped with welded nuts for the clamping bolts. On the joint side, the clamping bolt is pre-assembled; the clamping bolt on the opposite side is mounted into the bore hole and retained by a plastic washer, thus preventing any accidental unscrewing. For sizes 5 1/4" and larger the clamping bolts and the required nuts are supplied in loose form. With welded in 3G triple thread nut; without sound absorption lining. For further adapter-based connection options via the external thread of the 3G triple thread nut, see product "Adapter f/f" (this chapter). Technical Data Size [in] 5 76 - 129 mm /8 – 2 3 /4 3–5 5 1 /4 – 6 3 /4 7 – 12 Material: Working load (tension) [lb] 900 1125 1800 2800 Steel, electro-galvanised Approvals VdS-Approval No. G4920027, FM Approval Siconnect - Canada 4-2 02/2009 133 - 316 mm Pipe Clamps & Accessories Size range [in] NB [in] 3 /8 /2 3 /4 1 1 1 /4 1 1 /2 /8 – 3 /4 /4 – 1 1 – 1 3/16 1 1 /4 – 1 3 /8 1 1 /2 – 1 3 /4 1 7 /8 – 2 2 1/8 – 2 5/16 2 3/8 – 2 9/16 2 5 /8 – 2 3 /4 3 – 3 3/16 3 1/4 – 3 7/16 3 1 /2 – 3 5 /8 4 – 4 1 /4 4 5/16 – 4 9/16 4 7 /8 – 5 5 1 /4 – 5 1 /2 5 1 /2 – 5 3 /4 5 3 /4 – 5 7 /8 6 1 /4 – 6 1 /2 6 9/16 – 6 13/16 6 7 /8 – 7 1 /4 7 7/16 – 7 11/16 7 13/16 – 8 8 1 /8 – 8 1 /2 8 5 /8 – 8 7 /8 9 9/16 – 9 7/8 10 1/2 – 10 3/4 10 5/16 – 11 3/16 11 11/16 – 12 3 3 1 2 2 1 /2 3 4 5 6 8 10 Material [in] 1 x 14 ga 1 x 14 ga 1 x 14 ga 1 3/16 x 12 ga 1 3/16 x 12 ga 1 3/16 x 12 ga 1 3/16 x 12 ga 1 3/16 x 12 ga 1 3/16 x 12 ga 1 3/16 x 11 ga 1 3/16 x 11 ga 1 3/16 x 11 ga 1 3/16 x 11 ga 1 3/16 x 11 ga 1 3/16 x 11 ga 1 9/16 x 8 ga 1 9/16 x 8 ga 1 9/16 x 8 ga 1 9/16 x 8 ga 1 9/16 x 8 ga 1 9/16 x 8 ga 1 9/16 x 8 ga 1 9/16 x 8 ga 1 9/16 x 8 ga 1 9/16 x 8 ga 1 9/16 x 8 ga 1 9/16 x 8 ga 1 9/16 x 8 ga 1 9/16 x 8 ga Thread connection [in] 5 /8, 3/8, 5/16 /8, 3/8, 5/16 5 /8, 3/8, 5/16 5 /8, 3/8, 5/16 5 /8, 3/8, 5/16 5 /8, 3/8, 5/16 5 /8, 3/8, 5/16 5 /8, 3/8, 5/16 5 /8, 3/8, 5/16 3 /8, 1/ 2 3 /8, 1/ 2 3 /8, 1/ 2 3 /8, 1/ 2 3 /8, 1/ 2 3 /8, 1/ 2 1 /2 , 5 /8 1 /2, 5/8 1 /2, 5/8 1 /2 , 5 /8 1 /2 , 5 /8 1 /2 , 5 /8 1 /2 , 5 /8 1 /2 , 5 /8 1 /2 , 5 /8 1 /2 , 5 /8 1 /2 , 5 /8 1 /2 , 5 /8 1 /2 , 5 /8 1 /2 , 5 /8 5 B [in] W [lb] Quantity / pack 2 1 /4 2 7/16 2 11/16 3 3 5/16 3 11/16 4 1 /8 4 5/16 4 5 /8 5 5 /8 5 13/16 6 1/16 6 11/16 6 15/16 7 1 /2 8 1 /8 8 7/16 8 3 /4 9 1 /8 9 7/16 10 3/8 16 3/4 11 3/16 11 9/16 12 12 15/16 13 7/8 14 5/16 15 0.15 0.18 0.18 0.26 0.29 0.33 0.35 0.35 0.40 0.60 0.62 0.64 0.73 0.75 0.82 1.68 1.72 1.77 1.92 1.98 2.18 2.23 2.32 2.45 2.47 2.76 2.93 3.00 3.18 50 50 50 50 50 50 50 50 50 25 25 25 25 25 25 10 10 10 10 10 10 10 10 10 10 10 10 10 10 Part number 107705 107714 107723 107015 107024 107033 107042 107051 107060 107079 107088 107097 107103 107112 107121 107130 115885 107149 107158 107167 107176 107185 107194 148939 107200 107219 107228 107237 107246 02/2009 ga = gauge Siconnect - Canada 4-3 Pipe Clamps & Accessories Countersink Screw SCR Group: 1333 Application Connection element for Stabil D-3G pipe clamps sizes 3/8" up to 3/4" (with sound absorption lining up to 1/2") for suspending pipe clamps underneath one another. Technical Data Material: Steel, electro-galvanised Type [in] 5 3 /16 x /4 W [lb] Quantity/ pack 0.022 100 Part number 114097 Triple Thread Connecting Nut NT 3G Group: 1333 Application Connecting element for Sikla Stabil D-3G Pipe Clamps NB 1" or larger (with sound absorption lining 3/4" and larger) for suspending pipe clamps underneath one another. Technical Data Material: Steel, electro-galvanised 5 Siconnect - Canada 4-4 3 5 /8, /8, /16 W [lb] Quantity/ pack 0.044 50 Part number 146326 02/2009 Type [in] Pipe Clamps & Accessories Adapter AD f/f Group: 1333 Application Additional connection options for all Sikla pipe clamps equipped with 3G triple thread nut, fixed points and threaded tubes. Technical Data Material: Form A Steel, electro-galvanised Form B Malleable cast iron, electro-galvanised Type Form Length [in] A/F [in] /8", 3/8" /8", 1/2" 5 /8", 5/8" 3 /8", 5/8" 1 /2", 3/8" 1 /2", 1/2" 1 /2", 5/8" 1 /2", 3/8" 1 /2", 1/2" 3 /4", 3/8" 3 /4", 1/2" 3 /4", 5/8" 3 /4", 3/8" 3 /4", 1/2" A A A A A A A A A A A A A A 1 3 /8 1 3 /8 1 3/16 1 3 /8 1 3 /8 1 3 /8 1 9/16 1 3 /8 1 3 /8 1 3 /8 1 3 /8 1 3 /8 1 3 /8 1 3 /8 3 /4 /4 3 /4 3 /4 15 /16 15 /16 15 /16 15 /16 15 /16 1 1 /4 1 1 /4 1 1 /4 1 1 /4 1 1 /4 1", 3/8" 1", 1/2" 1", 5/8" 1", 3/8" 1", 1/2" B B B B B 1 9/16 1 9/16 1 9/16 1 9/16 1 9/16 5 C C 1 1 1 /8 5 5 02/2009 5 /8", 1/2" /8", 3/4" W [lb] Quantity/ pack 0.11 0.09 0.07 0.07 0.15 0.13 0.15 0.13 0.24 0.33 0.18 0.31 0.31 0.18 50 50 50 25 10 25 25 25 10 10 10 10 25 10 106740 124665 106290 146335 146371 156639 124656 146344 146380 105651 105749 105660 146353 146399 /8 /8 7 /8 7 /8 1 1/16 0.29 0.29 0.26 0.26 0.26 10 10 10 25 10 105679 105758 105688 146362 146405 - 0.13 0.20 25 25 157922 157931 3 7 7 Part number Siconnect - Canada 4-5 Pipe Clamps & Accessories Height Adjuster HRS 0 Group: 1339 Application Height adjustment unit for suspended pipelines and components, providing for accurate pipe laying and compensation of constructional building tolerances. Facilitates mounting and improves mounting efficiency on site. Technical Data Material: Connection to building structure Connection to system Max. perm. working load Adjustment range: Type 0 Steel, electro-galvanised 1 /2 " 3 /4" and 1/2" 337 lbs 1" W [lb] Quantity/ pack 0.18 50 Part number 125958 Height Adjuster HRS 1 Group: 1339 Application Height adjustment unit for suspended pipelines and components, providing for accurate pipe laying and compensation of constructional building tolerances. Facilitates mounting and improves mounting efficiency on site. Easy and infinitely variable height adjustment due to revolving cup nut and fitted thread. Configuration Pre-assembled component, no loose parts. Installation Fixing a locking nut against cup nut secures the height adjusted. Type 1 5 Siconnect - Canada 4-6 /2 /8 Cup nut [in] 1 5 /2 /8 Connection to building structure [in] 1 1 /2 /2 Steel, electro-galvanised 1 /2 " 3" 1350 lbs Adjustment height [in] W [lb] Quantity/ pack 1 9/16 1 9/16 0.40 0.40 25 25 Part number 125930 125949 02/2009 Technical Data Material: Connection to building structure Adjustment range Max. perm. working load Pipe Clamps & Accessories Height Adjuster HRS P Group: 1339 Application Suitable for all M&E services. May be fixed directly to the ceiling (anchor) or in a suitable channel. Especially advantageous due to the suspension unit in the upper section of the height adjuster, since it enables the pipes to move in all directions. Configuration Pre-assembled component, no loose parts. Installation The upper part of the base component can be used as a tool for screwing in the suspending bolt. Then the bolt only has to be tightened with an open-ended spanner. After mounting, the base component rests freely mobile and rotatable on the rounded bolt head. Fixing a locking nut against the cup nut secures the height adjusted. Technical Data Material: Base component cast iron, all components galvanised 900 lbs 7° Max. perm. working load Max. swinging angle Type 02/2009 P 5/16 P 3 /8 Connection Connection to building to system [in] structure [in] 5 /16 /8 3 5 /16 x 7/8 /8 x 7 /8 3 Adjustment height [in] W [lb] Quantity/ pack 1 1 0.13 0.18 25 25 Part number 151519 151528 Siconnect - Canada 4-7 Pipe Guides & Slide Elements 02/2009 2Pipe Guides & Slide Elements Slide Set GS H3G and H3G/3 Slide Set GS H3G/1 and H3G/4 Slide Set GS 2G Page 5-2 Page 5-3 Page 5-4 Slide Set GS 2G/1 Slide Element GS 41 Page 5-5 Page 5-6 Siconnect - Canada 5-1 Pipe Guides & Slide Elements Slide Set GS H3G and H3G/3 Group: 1336 Application Heavy-duty Slide Set for plant construction. To be used preferably in combination with Sikla pipe clamp Stabil D-3G and Refrigeration clamp SKS Top-2C. Various connection options of the pipe clamps depending on the respective load: 1/2", 5/8" or with 1/2" adapters using the external thread (see Adapter f/f). Sound absorption by means of glass fibre reinforced polyamide slide rails. Especially suitable for ceiling and floor mounting solutions and as a guide for rising pipes. For wall mounting, we recommend the use of the Slide Set H3G on Sikla Support Bracket. Installation For pipes of NB 3 15/16" or larger having to be spaced at a distance from the Slide Set, or under conditions of reversed bending stress, the 3G triple thread nuts are to be secured by screwing on a 1/2" Locking Nut. H3G Technical Data Permissible load for ceiling mounting Permissible load for floor mounting Permissible bending moment for wall mounting* for H3G: Lever arm Lmax: Maximum sliding distance H3G: H3G/3: Temperature range (permanent exposure): Static friction coefficient µ0 : Sliding friction coefficient µ: 5 5/16" 3 15/16" 266°F 0.18 0.14 Material: Metal components Steel, electro-galvanised 1125 lbs 2025 lbs 780 lbs 15 3/4" * The permissible bending moment of the connecting element (threaded rod or threaded tube) may restrict the application! Type H3G H3G/3 W [lb] Quantity/ pack 3.41 2.46 10 10 Part number 126700 149295 Siconnect - Canada 5-2 02/2009 H3G/3 Pipe Guides & Slide Elements Slide Set GS H3G/1 and H3G/4 Group: 1336 Application Heavy-duty Slide Set for plant construction, to be used on Sikla Channels, brick or concrete walls and on bearers. This Slide Set version is especially suitable for bolted mounting to the building structure. To be used preferably in combination with Sikla pipe clamp Stabil D-3G and refrigeration clamp SKS Top-2C. Various connection options of the pipe clamps depending on the respective load: 1/2", 5/8" or with 1/2" adapters using the external thread (see Adapter f/f). Sound absorption by means of glass fibre reinforced polyamide slide rails. Especially suitable for ceiling and floor mounting solutions and as a guide for rising pipes. Installation For pipes of NB 3 15/16" or larger having to be spaced at a distance from the Slide Set, or under conditions of reversed bending stress, the 3G triple thread nuts are to be secured by screwing on a 1/2" Locking Nut. H3G/1 Technical Data Permissible load for ceiling mounting Permissible load for floor mounting Lever arm Lmax: Maximum sliding distance: H3G/1 H3G/4 Temperature range (permanent exposure) Static friction coefficient µ0 Sliding friction coefficient µ 5 5/16" 3 15/16" 266°F 0.18 0.14 Material: Metal components Steel, electro-galvanised Type H3G/1 H3G/4 1125 lbs 2025 lbs 15 3/4" W [lb] Quantity/ pack 4.05 3.12 10 10 Part number 126658 149301 02/2009 H3G/4 Siconnect - Canada 5-3 Pipe Guides & Slide Elements Slide Set GS 2G Group: 1336 Application Slide Set for single and double mounting of mechanical equipment. To be used preferably in combination with Sikla Pipe Clamps Ratio S and Stabil D-3G. Various connection options with these pipe clamps ranging between 3/8" and R1". For adapters for these connection options (see Adapter f/f). Sound absorption by means of glass fibre reinforced PA slide rails. 135 lbs 270 lbs 11 13/16" 3 11/32" 5 1 /2 " 266°F 0.18 0.14 Material: Metal components Steel, electro-galvanised Type 1-2G 2-2G Siconnect - Canada 5-4 W [lb] Quantity/ pack 0.85 1.09 25 25 Part number 126755 126764 02/2009 Technical Data Permissible load for ceiling mounting Permissible load for floor mounting Lever arm Lmax: Max. sliding distance Type 1-2G Max. sliding distance Type 2-2G Temperature range (permanent exposure) Static friction coefficient µ0 Sliding friction coefficient µ Pipe Guides & Slide Elements Slide Set GS 2G/1 Group: 1336 Application Slide Set for single and double mounting of mechanical equipment, to be used on Sikla Channels, brick or concrete walls and on bearers. To be used preferably in combination with Sikla Pipe Clamps Ratio S and Stabil D-3G. Various connection options with these pipe clamps ranging between 3/8" and R1". For adapters for these connection options (see Adapter f/f). Sound absorption by means glass fibre reinforced PA slide rails. Technical Data Permissible load for ceiling mounting Permissible load for floor mounting Lever arm Lmax: Max. sliding distance Type 1-2G Max. sliding distance Type 2-2G Temperature range (permanent exposure) Static friction coefficient µ0 Sliding friction coefficient µ 135 lbs 270 lbs 11 13/16" 3 11/32" 5 1 /2 " 266°F 0.18 0.14 Material: Metal components Steel, electro-galvanised Type 02/2009 1-2G/1 2-2G/1 W [lb] Quantity/ pack 1.20 1.44 25 25 Part number 127127 127136 Siconnect - Canada 5-5 Pipe Guides & Slide Elements Slide Element GS 41 Group: 1336 Application Slide element for use in Sikla Channels of the 41 series. For single and, using a Tandem Connector, double mounting options. The sliding distance is determined by the length of the rail. Holding Brackets are to be used for securing the slide element. Alternatively, the Sikla Channel Holder SH may be used. Any option in combination with Sikla Pipe Clamps Ratio S and Stabil D-3G may be realised. Various connection options with pipe clamps in the range between 1/2" and R1". For these connection options, the corresponding Mounting Plate could be screwed directly with the slide element by means of bolts 3/8" x 3/4". Suitable for ceiling and floor mounting solutions and as a guide for rising pipes. Technical Data Permissible load overhead mounting: Single mounting Double mounting The permissible load capacity of the channel has to be respected. 1350 lbs 1800 lbs Permissible load floor mounting: Single mounting/Double mounting Single mounting with mounting plate 900 lbs 1800 lbs Lever arm Lmax for single mounting: Static friction coefficient µ0: Sliding friction coefficient µ: Material: 13 3/4" 0.16 0.14 Steel, electro-galvanised The permissible bending moment of the connection elements (threaded rod or threaded tube) may restrict the application! Thread connection [in] 41 – 3/8 3 /8 W [lb] Quantity/ pack 0.40 10 Part number 190658 02/2009 Siconnect - Canada 5-6 Type
© Copyright 2024