1. home and garden
2. home improvement and repair
3. plumbing

Date: 3rd July 2014
To The Tenderers
Whatawhata School – New Roll Growth Spaces
Notice to Tenderers #1
The following are clarifications to or changes to the tender documents:
1
Please allow to install a hook rail into each of the two changing rooms along
with hooks. The hook rail location is to correspond with the seats in the changing
rooms. This is as indicated on the attached revisions of sheets 102 and 303.
2
Please allow to install a new drinking fountain onto the south wall of the toilets.
This is to be as indicated on the attached revisions of sheets 102, 113 & 201.
3
High level windows in the classroom, breakout room and library/MP room are to
opened and closed with electronic winding gear. This is to be as indicated on
the attached revisions of sheets 108 & 502.
4
There have been numerous minor changes made to the attached revision of
sheet 108 (Electrical/Data/Alarms Plan). This are listed as follows:
 Speaker input point in classroom has been moved
 HDMI input/output points added to classroom and library/MP room
 4 extra data points added to ceiling in library/MP room
 Two new double power points added in music store within joinery
 Window winding gear now shown as per 3 above.
5
The Mikes Woodshop whiteboard unit specification has been altered and the
modules included are now to be D, B & D in lieu of the modules originally
specified. This is indicated on the attached revision of sheet 204.
6
Interior elevations for the library/MP room have been updated to show the wall
mounted shelving. Please note that Composition is to be laid behind these
fittings. Refer attached revision of sheet 206.
7
The backs of the hinged shelving units on the south wall of the library/MP room
are to have whiteboards on the upper half of them. This is now indicated on the
revision of sheet 406 attached.
P O Box 297 Te Awamutu 3840
Phone: 07 870 5200 extn 2 / Fax: 07 870 5300 / Mobile: 029 870 5200
www.gisler-architects.co.nz
PDF processed with CutePDF evaluation edition www.CutePDF.com
8
Door hardware to doors D101, D103 & D105 has been changed to delete the
pedestal latchback and include a door closer with hold-open. This is as
indicated on the attached revision of sheet 501.
9
Windows W106 – W109 are to have obscure glass in lieu of clear. This is now
indicated on the attached revision of sheet 502.
10
Joinery units U106, U107 & U108 have all been changed. Please refer to the
attached revision of sheets 504 & 505.
11
Wall linings in the music store are to be painted GIB to level 4 in lieu of
composition. This is as indicated on the revised sheet 506 attached.
Please acknowledge receipt of this notice in your tender submission.
Yours faithfully
Mark Owens
Architect
On behalf of Gisler Architects Ltd
P O Box 297 Te Awamutu 3840
Phone: 07 870 5200 extn 2 / Fax: 07 870 5300 / Mobile: 029 870 5200
www.gisler-architects.co.nz
School Road
3. Scope of Works
23,086
9,615
6,800
90
4,117
7,903
140
140
5,000
90
2,824
2,613
3
6
2,106
4
5
L/MP-01
206
D153
BR-02
205
8,280
F
108°
4
D10
18°
ndah
a
r
e
V
7
9,24
F
Path
g
n
i
Exist
2,858
BR-04
205
Bag Hooks
nels
r Pa
Doo arked
P
A
Drinking
Fountain
8,972
D152
W103
D154
CR-04
204
B
A
3.6m Whitebd Storage Unit
U101
D108
D110 D109
Block A
90
B
W108 D111 D112W109
W107
U102
D107
W106
2x Showers
CR-02
204
3,106
90 1,000
2,106
2,016
140
90 1,000 90
90
4,005
2,915
90
2,915
8,000
140
855
900
3,700
900
865
D
Tree
E
Verandah
3.01.02
16
3.1m²
D
D103
11
14
5
D10
P-05
L/M 06
2
Boys' WC
D102
12
13
C
P-04
L/M 06
2
BR-03
205
o)
3.1m²
Bag Hooks
(19no)
68.4m²
E
90
31.0m²
CR-03
204
9°
Library Outdoor Area
9,084
62.9m²
Whiteboard
Girls' WC
Library/MP Room
h
Veranda
L/MP-02
206
Breakout Room
Classroom
D101
W151
Fold-away Library Shelving
CR-01
204
10.8m²
D151
Tree
15
Girls Change
8
10
Hooks above
7
401
9
Hooks above
Hooks above
90
1,000
Door Panels
Parked
2
X8
D106
10.8m²
BR-01
205
W201 (above)
helving
Library S
14,086
W203 (above)
5.3m²
W202 (above) U107
y
Fold-awa
4,005
U103
10.0m²
3
L/MP-0
206
3.01.03
W204 (above)
W104
Issues/
Librarian
Music Store
1
Boys Change
3.01.03
W101
C
U106
U105
(24n
1,755 90
U104
W205 (above)
W105
Hooks above
3.01.02
W102
3.01.01
8
1,51
1,765 90
406
U108
2,106
X10
Pool Area
1,421
9,124
1,444
140
Remove existing chainlink
boundary fence.
Demolish existing concrete block
wall down to 300mm below
ground level.
Remove sections of existing pool
fence where new building is
located and re-use to re-shape
fence area (see siteworks plan).
2,256
2,725
3.01.01
1,421
Returns
2,815
90
12,050
90
1,820 90
7,958
140
2,824
10,922
140
9,124
469
8,795
Pool Area
Tree
Existing Concrete Paving
Contractor to verify and confirm on site all dimensions, levels, falls, heights, structure, services and notify Architect of any discrepancies in documents prior to commencement of works.
PROJECT TITLE:
Whatawhata School
New Roll Growth Spaces
Tender Set
REVISIONS:
DRAWING TITLE:
DRAWN:
A Hooks to changing & drinking fountain. 2/7/14
Floor Plan
JOB NO.:
SHEET:
SCALE:
1:100 @A3
DATE:
26/6/14
www.gisler-architects.co.nz
MW
5270
CHECKED:
FILE: 5270 Whatawhata Roll Growth 2014 WD.pln
REVISION:
102 A
59 Bank Street, P O Box 297, Te Awamutu 3840
Phone: 07 870 5200 Fax: 07 870 5300
School Road
1. Important Notes
1.11.01
1.11.02
1.11.03
PP
Music Store
10.0m²
2 2j 2j
WG
WG
WG
WG
WG
2
WG
s Sout
WG
WG
2c 2c 2c
31.0m²
62.9m²
Sout 2 2 2 Sin Vin
1h 1h
11.01.01 Install compliant Type 4 alarm system to new spaces and
connect to existing analogue addressable panel in admin
block.
11.01.02 Connect all new security fittings to existing school alarm
system located in admin block.
New Distribution Board: Wall mounted lockable steel cabinet
Outdoor
Area cable from
with all MCBsLibrary
for this block.
Run new sub-main
existing School MSB in adjacent block (refer to site plan).
New Patch Panel: 12 RU lockable wall-mounted cabinet with
PP
double powerpoint inside. Layout as listed below (switch to be
supplied by school and installed by contractor).
1
2
3
4
5
6
2
2 2
Vout2b WG cp
s
cp
k s
2 2 2
2
s
cp
Girls' WC
3.1m²
1h
hd
Fibre tray
Cable management
4 - port voice link
Cable management
24 - port patch panel
Cable management
7
8
9
10
11
12
Connect patch panel to schools existing main patch
panel (refer to site plan) via 6 core OM3 fibre optic
backbone (with sc connectors).
- Connect voice link ports to existing phone system via 15
pair UTP cable.
- Allow to install new fibre tray to existing patch panel as
required for connection.
New Power Point: PDL 500 series plate
h arrangements
atwith
and mounting heights as follows:ing P
Exist
'1h' = single switched outlet
'2' = double switched outlet
'2b' = double switched outlet
'2j' = double switched outlet (see joinery sch)
'St' = stove 32A supply w/remote switch
'2pp' = dbl switched outlet (dedicated circuit)
'2c' = double switched outlet
'Rh' = hard wired supply to range hood
'2x' = PDL WP Series dbl switched outlet
S out
ndah
a
r
e
V
Verandah
2x
hd
1h
Boys' WC
2
3.1m²
WG
Pool Area
WG
Existing Concrete Paving
Sin
New Manual Call-point: Position adjacent to all external
doorways. Connect to school's existing fire alarm system. To
be analogue addressable compatible.
New Winding Gear: Electrically operated openers to each
high level window. Interlock Elevations. Allow to connect two
motors/actuators to each sash (each window has two
sashes) and wire back to control panel as indicated.
New Winding Gear Switch: Interlock Elevations touch screen
control panel mounted 1,500mm above floor.
Hot Water Cylinder: Rheem 25L mains pressure unit. Allow
to supply power.
Instant Water Heater: Clage MCX 6 instant water heater
mounted on wall above basin (1.8m above floor). Allow to
connect to 25A power supply.
k
s
1000mm off floor
500mm off floor
2200mm off floor
Mounted on ceiling
Run Cat6 cable from each RJ45 outlet to patch panel.
New AV Point: PDL 500 series plate with outlets and heights
as follows:
'Sin' = Speaker 2xRCA input point
'Sout' = Speaker 1xRCA output point
'Vin' = Video HDMI input point
'Vout' = Video HDMI output point
hd
2200mm off floor
500mm off floor
1200mm off floor
Within joinery unit
500mm off floor
inside PP cabinet
Mounted on ceiling
Allow to hard-wire connections for Stove and Range Hood
(stove to be supplied by school).
New Data Point: PDL 500 series plate with outlets and
Block A
heights as follows:
'2' = double RJ45 outlet
'1h' = single RJ45 outlet
'2c' = double RJ45 outlet
cp
Switch
Empty (for future use)
Empty (for future use)
Empty (for future use)
Empty (for future use)
Empty (for future use)
-
Sout
1h
1hVout
68.4m²
h
Veranda
Library/MP Room
Breakout Room
Classroom
1h1h
10.8m²
10.8m²
WG
2x
Boys Change
Girls Change
2 2 2 WG
11. Electrical/Data/Alarms
Electrical
DB
WG
2c 2c 2c
2 2 2 Sout
WG
5.3m²
Sout
1h
DB
s
Issues/
Librarian
2
2b s
2b Rh St 2b
Vin
2 2 2 Sin
Pool Area
2pp
1.11.05
The position of outlets and equipment shown on drawings are
indicative only. Outlets and equipment are not drawn to scale.
Contractor must liaise with Architect for confirmation of all
electrical fittings positioning prior to lining.
All switch and socket units are to be PDL500 series as
specified. No other types will be accepted.
All outlets are to be installed horizontally and consistently set
out in relation to studs.
All data work must be carried out by MOE certified installers
with MOE approved equipment, to comply with current MOE
standards at the time of installation and be supplied with a 25
year manufacturer's warranty.
900mm off floor
2200mm off floor
900mm off floor
1200/2200mm
Run 2.0mm shielded speaker cable between Sin and Sout
points. Run HDMI cable between Vin and Vout points.
New Hand Dryer: Supreme BA101 hand dryer with remote
PDL 500 switch above.
New Security Keypad: Position here. Connect to school's
existing security alarm system.
New PIR Sensor: Connect to existing security alarm system.
Positions are approximate only - allow for number and
positions as necessary to provide cover to all spaces.
Contractor to verify and confirm on site all dimensions, levels, falls, heights, structure, services and notify Architect of any discrepancies in documents prior to commencement of works.
PROJECT TITLE:
Whatawhata School
New Roll Growth Spaces
Tender Set
REVISIONS:
DRAWING TITLE:
Electrical/Data/Alarms Plan
SCALE:
1:100 @A3
DATE:
26/6/14
A Winding gear to upper windows.
HDMI points for video CR & Library.
Extra data points on library ceiling.
Extra power points to music store.
DRAWN:
2/7/14
JOB NO.:
SHEET:
www.gisler-architects.co.nz
MW
5270
CHECKED:
FILE: 5270 Whatawhata Roll Growth 2014 WD.pln
REVISION:
108 A
59 Bank Street, P O Box 297, Te Awamutu 3840
Phone: 07 870 5200 Fax: 07 870 5300
1. Important Notes
18.07.HT
18.02.GT
18.02.TV
18.08.HC
18.03.SH
SH
SH
SH
GT
IJ
IB
18. Plumbing & Drainage
DP
X1
40mm
404
IJ
100mm
HT
IJ
DP
18.03.DC
TV
100mm
100
m
m
IJ
18.04.DP
100mm
18.03.IB
1.18.01 Determine the location of all underground services
before the commencement of work.
1.18.02 All exposed waste pipes to be chrome plated copper
with associated 18.03.01
chrome fittings.
18.02.01
1.18.03 Refer to finishes schedule for details of plumbing and
1.18.01
drainage fittings 1.18.02
and fixtures. 1.18.03
25.08.02
25.08.01
18.03.CP
25.08.01
25.08.02
CP
18.01.04
0m
10
100mm
SV
HT
IJ
m
IJ
GT DP
DP
m
m
IJ
IJ
10
0
0m
10
32mm
18.02.GT
32mm
18.08.01
100
mm
18.07.HT
10
0m
m
18.12.DF
m
0m
10
18.03.IJ
DP
18.02.IJ
18.04.DP
150
m
m
IJ
18.07.01
18.03.DC
m
18.08.01
18.07.SV
18.01.01 Connect new sanitary drain to existing septic tank
system - see site plan for location.
18.01.02 Allow to disconnect and reconnect pumbing to
existing pool pump & filter system to allow removal of
existing building and installation of new shed.
18.01.03 Existing strip drain and catchpit to remain.
18.01.04 Remove section of existing strip drain where new
building and paving work occur..
18.02.01 Sanitary plumbing and drainage: uPVC pipework to
sizes noted. Lay to minimum falls to comply with
NZBC G13/AS1 and AS2.
18.02.GT Gully trap: Domestic uPVC fitting haunched into
concrete. To comply with NZBC G13/AS1.
18.02.IJ Inspection junction: To comply with NZBC G13/AS2.
18.02.TV Terminal vent: To comply with NZBC G13/AS1
surface mounted to exterior wall. Fit decktite flashing
around vent where it penetrates through roof.
18.03.01 Stormwater drainage: uPVC pipework to sizes noted.
Lay to minimum falls to comply with NZBC E1/AS1.
18.03.CP uPVC catch pit: 300x300mm proprietary uPVC
catchpit with steel grate. Fall adjacent ground
surfaces towards catchpit.
18.03.DC Drainage Channel: ACO ThresholdDrain stainless
steel cantilevered grate system. Install to
manufacturers instructions.
18.03.IB Inspection bend: To comply with NZBC E1/AS1.
18.03.IJ Inspection junction: To comply with NZBC E1/AS1.
18.03.SH Soak hole: 900mm dia x 1800mm deep soak hole
with porous concrete liner and concrete lid. To
comply with NZBC E1/VM1.
18.04.DP 100mm dia sewer grade uPVC downpipe with
stormwater gully at base haunched into concrete.
18.07.01 Water supply: Run new supply from adjacent block.
18.07.HT Hose Tap: Standard brass tap with removable spigot.
Position over gully traps where applicable.
18.07.SV Stop valve: Set in standard Toby box with lid.
18.08.01 Clage MCX 6 instant water heater mounted on wall
above basin (1.8m above floor). Supply cold water to
unit and hot water to taps with all pipework
concealed. within wall linings.
18.08.HC Under-bench HWC: Rheem 25L mains pressure
under-bench unit with Delabie Premix 733020 water
mixer. (HWC is 405mm dia x385mm high). Connect
to sinks as indicated. Provide overflow pipe to
exterior.
18.12.DF Elkay EDF-20-C stainless steel drinking fountain with
LK-142 bubbler fixed to exterior wall of building. To
have chrome plated copper waste pipe with chrome
steel brackets. Run copper water pipe from inside
wall of building. Mount drinking fountain 700mm
from the top to finished ground level.
25. Sanitary Hardware
25.08.01 Delabie DE709000 'Round' vandal proof wall
mounting shower head, with an adjustable scaleproof nozzle and fixed 6 L/min flow-restrictor. Body
in chrome plated brass with anti-rotating stop lug.
25.08.02 Delabie DE790220 automatic 30s shut-off delayed
shower mixer including a chrome plated brass plate
160x220mm, in water proof recessing box, with
stop cocks.
18.01.01
18.01.02
18.01.03
Contractor to verify and confirm on site all dimensions, levels, falls, heights, structure, services and notify Architect of any discrepancies in documents prior to commencement of works.
PROJECT TITLE:
Whatawhata School
New Roll Growth Spaces
Tender Set
REVISIONS:
DRAWING TITLE:
Plumbing & Drainage Plan
A Drinking fountain added.
DRAWN:
2/7/14
JOB NO.:
SHEET:
SCALE:
1:100 @A3
DATE:
26/6/14
www.gisler-architects.co.nz
MW
5270
CHECKED:
FILE: 5270 Whatawhata Roll Growth 2014 WD.pln
REVISION:
113 A
59 Bank Street, P O Box 297, Te Awamutu 3840
Phone: 07 870 5200 Fax: 07 870 5300
9.07.01
20.02.01
21.02.01
25.08.01
25.08.02 10.02.03
9.02.01
18.04.DP1
9.06.02
9.07.01
20.02.01
7.11.01
10.02.03
9.02.01
9.06.02
21.02.01
2,500
37°
2,500
37°
n o r t h
s o u t h
7. Roof Structure
7.11.01 89x3.5 SHS steel verandah frames fixed to wall framing at top end and
cast into concrete footings at ground. Hot dip galnvanise after
fabrication.
7.11.01
10.15.01
18.04.DP1
21.02.01
9.02.01
9.06.02
10.02.03
9.07.01
9. Roofing
9.02.01 0.55 gauge trapeziodal Colorsteel Endura roofing fixed with colour
matched tek-screws over Thermakraft Covertek403 absorbent
breathable synthetic non-woven roofing underlay and wire mesh.
9.06.02 125mm square Colorsteel Endura guttering fixed with colour-matched
concealed brackets.
9.07.01 Ex 25mm H3.2 timber fascia and barge boards.
10. Claddings
10.02.03 9mm James Hardie 'Titan' facade panel cladding with 10mm expressed
vertical joints and PVC 'h' moulds to horizontal joints, fixed to CLD cavity
battens over Thermakraft Coverup building wrap.
10.15.01 6mm Hardieflex soffit linings with uPVC jointers. Fix at inside edge to
nogged 75x40 battens. To verandah areas, fix at sheet joints and midspan to nogged 70x45 battens.
e a s t
18. Plumbing & Drainage
18.04.DP 100mm dia sewer grade uPVC downpipe with stormwater gully at base
haunched into concrete.
18.04.DP
24.14.01 20.02.01
7.11.01
24.14.01 9.02.01
9.06.02 10.02.03
10.15.01
9.07.01
20. Doors
20.02.01 Exterior powder-coated aluminium door joinery (refer to schedules).
21. Windows
21.02.01 Exterior powder-coated aluminium window joinery (refer to schedules).
24. Fittings
24.14.01 2/Ex 150x40 pine - painted - bag rails (top and bottom) with arrissed
edges fixed to studs through 35mm packers at 1200mm centres.
Provide Devon 273 bag hooks (satin chrome) at 250mm crs, number of
hooks as noted on plan. Alternate hooks between bottom and top rails.
25. Sanitary Hardware
w
e
s
25.08.01 Delabie DE709000 'Round' vandal proof wall mounting shower head,
with an adjustable scale-proof nozzle and fixed 6 L/min flow-restrictor.
Body in chrome plated brass with anti-rotating stop lug.
25.08.02 Delabie DE790220 automatic 30s shut-off delayed shower mixer
including a chrome plated brass plate 160x220mm, in water proof
recessing box, with stop cocks.
t
Contractor to verify and confirm on site all dimensions, levels, falls, heights, structure, services and notify Architect of any discrepancies in documents prior to commencement of works.
PROJECT TITLE:
Whatawhata School
New Roll Growth Spaces
Tender Set
REVISIONS:
DRAWING TITLE:
A Drinking fountain added.
Elevations
DRAWN:
2/7/14
JOB NO.:
SHEET:
SCALE:
1:100 @A3
DATE:
26/6/14
www.gisler-architects.co.nz
MW
5270
CHECKED:
FILE: 5270 Whatawhata Roll Growth 2014 WD.pln
REVISION:
201 A
59 Bank Street, P O Box 297, Te Awamutu 3840
Phone: 07 870 5200 Fax: 07 870 5300
15.02.10
W204
W105
W104
15.02.10
16.12.01
20.05.02
2,563
3,261
W205
16.12.01
698
21.02.01
2,825
3,261
16.12.01
D154
U102
23.02.01
17.02.21
I n t e r i o r
22.03.02
E l e v a t i o n
17.02.21
0 1
22.03.02
I n t e r i o r
D102
24.15.07
D101
U101
22.03.02
I n t e r i o r
17.02.21
U101
23.02.01
E l e v a t i o n
24.15.06
3,261
2,563
16.12.01
2,563
20.02.01
0 2
698
16.12.01
E l e v a t i o n
U102
23.02.01
0 3
22.03.02
I n t e r i o r
17.02.21
E l e v a t i o n
0 4
15. Ceilings
20. Doors
15.02.10 25x60 pine clears architrave to edge of
bulkhead ceiling. Clear finished.
20.02.01 Exterior powder-coated aluminium door joinery
22.03.02 40x10mm clears pine coving bead at 150mm
(refer to schedules).
from FL.
20.05.02 D153 & D154 are to be 'Transpace Spaceseal'
501 operable acoustic wall with a Jamb Hinged
23. Joinery
Passage Door as shown (see floor plan for
handing of passage door). Install to
23.02.01 Interior joinery (refer to schedules).
manufacturers requirements. To have a 45 STC
rating and have Autex Compostion installed to
both sides of operable wall configuration.
16. Wall Linings
16.12.01 Autex Composition over base lining from
190mm to ceiling.
22. Internal Trims
24. Fittings
17. Floor Coverings
17.02.21 Cove carpet up walls 150mm.
24.15.06 Whiteboard storage unit from Mike's
Woodshop. 3.6m wide with modules D, B & D as
indicated.
24.15.07 Wall mounted flat screen TV (to be supplied by
school).
21. Windows
21.02.01 Exterior powder-coated aluminium window
joinery (refer to schedules).
Contractor to verify and confirm on site all dimensions, levels, falls, heights, structure, services and notify Architect of any discrepancies in documents prior to commencement of works.
PROJECT TITLE:
Whatawhata School
New Roll Growth Spaces
Tender Set
REVISIONS:
DRAWING TITLE:
Interior Elevations: Classroom
A Mike's Woodshop unit changed.
DRAWN:
2/7/14
JOB NO.:
SHEET:
SCALE:
1:50 @A3
DATE:
26/6/14
www.gisler-architects.co.nz
MW
5270
CHECKED:
FILE: 5270 Whatawhata Roll Growth 2014 WD.pln
REVISION:
204 A
59 Bank Street, P O Box 297, Te Awamutu 3840
Phone: 07 870 5200 Fax: 07 870 5300
16.12.01
16.12.01
20.05.02
709
W202
3,002
3,711
21.02.01
W201
3,711
15.02.10
24.10.01
W151
D154
17.02.21
22.03.02
0 1
I n t e r i o r
20.02.01
22.01.01
E l e v a t i o n
0 2
24.10.01
15.02.10
164
16.12.01
20.02.01
D105
17.02.21
22.03.02
20.02.01
D104
17.02.21
20.02.01
3,118
D106
2,825
3,118
3,711
75
16.12.01
2,876
593
16.12.01
E l e v a t i o n
22.03.02
218
I n t e r i o r
17.02.21
585
80
D151
17.02.21
22.03.02
22.03.02
I n t e r i o r
E l e v a t i o n
0 3
I n t e r i o r
E l e v a t i o n
20. Doors
15. Ceilings
15.02.10 25x60 pine clears architrave to edge of bulkhead
ceiling. Clear finished.
16. Wall Linings
16.12.01 Autex Composition over base lining from 190mm to
ceiling.
0 4
E l e v
0 5
22. Internal Trims
20.02.01 Exterior powder-coated aluminium door joinery (refer to 22.01.01 Returns slot through wall into joinery unit in Library
schedules).
Office. Refer to detail.
20.05.02 D153 & D154 are to be 'Transpace Spaceseal' 501
22.03.02 40x10mm clears pine coving bead at 150mm from FL.
operable acoustic wall with a Jamb Hinged Passage
Door as shown (see floor plan for handing of passage
door). Install to manufacturers requirements. To have a 24. Fittings
45 STC rating and have Autex Compostion installed to
24.10.01 Adjustable shelving with powder-coated steel shelves.
both sides of operable wall configuration.
Refer to details and schedule.
21. Windows
17. Floor Coverings
21.02.01 Exterior powder-coated aluminium window joinery (refer
to schedules).
17.02.21 Cove carpet up walls 150mm.
Contractor to verify and confirm on site all dimensions, levels, falls, heights, structure, services and notify Architect of any discrepancies in documents prior to commencement of works.
PROJECT TITLE:
Whatawhata School
New Roll Growth Spaces
Tender Set
REVISIONS:
DRAWING TITLE:
Interior Elevations: Library/MP Room
A Shelving now shown.
DRAWN:
2/7/14
JOB NO.:
SHEET:
SCALE:
1:50 @A3
DATE:
26/6/14
www.gisler-architects.co.nz
MW
5270
CHECKED:
FILE: 5270 Whatawhata Roll Growth 2014 WD.pln
REVISION:
206 A
59 Bank Street, P O Box 297, Te Awamutu 3840
Phone: 07 870 5200 Fax: 07 870 5300
7.07.01
7.06.01
7.03.06
9.06.02
6.02.03
9.02.01
7.06.02
7.03.01
15.05.01
6.09.03
7.06.02
7.04.07
8.05.02
7.03.01
7.06.02
7.03.03
9.07.01
10.02.03
9.07.01
C3
403
5°
Boys Change
Breakout Room
403
10.15.01
7.04.05
9.06.02
16.02.02
8.04.01
6.02.04
18.03.DC
19.02.01
Library/MP Room
2,910
2,656
2,421
Classroom
C2
C4
1,500
9.07.01
10.15.01
21.02.01
15.02.01
24.14.03
10.02.03
8.04.01
16.05.04
6.02.04
6.09.03
403
C1
402
6.02.01
5.03.03
8.06.01
5. Foundations
100mm thick concrete floor slab with
SE62 reinforcing mesh on DPM on a
200mm thick layer of compacted
hardfill.
Perimeter footing to be continuous
20MPa concrete, 300mm wide at
base with 3/D12 reinforcing bars
with D10 ties at 600mm crs, lapped
into floor slab 600mm. Footing to
extend a minimum of 300mm below
finished ground level.
300mm wide x 200mm deep slab
thickening under load-bearing walls
with 2/D12 reinforcing bars 75mm
from bottom of thickening with R6
ties at 600mm crs.
5.02.01
5.03.03
5.04.01
6. Wall
6.02.01
6.02.03
6.02.04
6.09.03
5.04.01
8.02.02
250PFC steel portal frame. Refer to
structural engineers documents.
8.04.01
7. Roof Structure
5.02.01
Autex Greenstuf R2.5 insulation pads
16.05.04 12mm Plywood Grade BD direct fixed
10. Claddings
(90mm) to all new exterior wall
to wall framing with close V-Butted
10.02.03 9mm James Hardie 'Titan' facade
cavities.
joints. Clear finish.
panel cladding with 10mm expressed
vertical joints and PVC 'h' moulds to
Autex Greenstuf R3.4 skillion roof
horizontal joints, fixed to CLD cavity
blanket (165mm) to all new skillion
18. Plumbing & Drainage
battens over Thermakraft Coverup
ceiling cavities. Strap insulation up
18.03.DC Drainage Channel: ACO
building wrap.
between roof structure with stud
ThresholdDrain stainless steel
straps staped to structure at
10.15.01 6mm Hardieflex soffit linings with
cantilevered grate system. Install to
300mm centres.
uPVC jointers. Fix at inside edge to
manufacturers instructions.
nogged 75x40 battens. To verandah
Autex Quietstuf Sound Solution
areas, fix at sheet joints and mid-span
acoustic insulation pads or roll form
to nogged 70x45 battens.
19. Siteworks
(90mm) fitted into wall cavities.
8.05.02
150x45 HySpan rafters at 900mm
centres.
7.03.03 140x45 H1.2 SG8 Fly-rafter
supported by outriggers.
7.03.06 190x45 H1.2 SG8 rafters at 900mm
centres.
8.06.01
7.04.05 140x45 H1.2 SG8 structural purlins
at 600mm crs to verandah roof.
7.04.07 190x45 H1.2 SG8 structural purlins
19.02.01 100mm thick concrete paving with
15. Ceilings
at 900mm crs.
sawcuts every 5m laid to levels as
15.02.01 13mm Gib board fixed to 75x40
9. Roofing
7.06.01 90x45 H1.2 SG8 outriggers at
indicated. To have a light broom finish.
ceiling battens at 600mm crs. Stop
900mm crs max fixed to side of
to a level 4 finish and paint.
9.02.01 0.55 gauge trapeziodal Colorsteel
rafter/structural purlin.
Endura roofing fixed with colour
Armstrong RH99 fine fissured
15.05.01
21. Windows
7.06.02 140x45 H1.2 SG8 outriggers at
matched tek-screws over
Structure
1200x600mm
ceiling
tiles
in
Rondo
900mm crs max butted to side of
Thermakraft Covertek403 absorbent
Duo 2-way exposed suspended grid 21.02.01 Exterior powder-coated aluminium
90x45 H1.2 SG8 framed walls with
rafter.
breathable
synthetic
non-woven
window joinery (refer to schedules).
system. To be hung raking at 150mm
studs at 600mm crs.
7.07.01 70x45 H1.2 SG8 purlins at 900mm
roofing underlay and wire mesh.
below underside of roof structure.
140x45 H1.2 SG8 framed walls with
crs.
studs at 600mm crs.
9.06.02 125mm square Colorsteel Endura
24. Fittings
guttering fixed with colour-matched 16. Wall Linings
140x45 H1.2 SG8 framed walls with 8. Insulation
24.14.03 Ex 150x40 pine - painted - hook rail.
concealed brackets.
studs at 400mm crs for 140mm
16.02.02 10mm Gib board base lining direct
Expol
R1.11
Grade
H
expanded
Detail to be similar to bag rails (refer
8.02.02
fixed to framing. Stop to a level 3
walls with stud lengths more than
polystyrene (40mm) to all new
detail F1), but only a single rail
9.07.01 Ex 25mm H3.2 timber fascia and
finish.
3.6m.
concrete floor slabs.
barge boards.
mounted 1,500mm above floor.
7.03.01
Contractor to verify and confirm on site all dimensions, levels, falls, heights, structure, services and notify Architect of any discrepancies in documents prior to commencement of works.
PROJECT TITLE:
Whatawhata School
New Roll Growth Spaces
Tender Set
REVISIONS:
DRAWING TITLE:
A Hooks added to changing room.
Section C - C
DRAWN:
2/7/14
JOB NO.:
SHEET:
SCALE:
1:50 @A3
DATE:
26/6/14
www.gisler-architects.co.nz
MW
5270
CHECKED:
FILE: 5270 Whatawhata Roll Growth 2014 WD.pln
REVISION:
303 A
59 Bank Street, P O Box 297, Te Awamutu 3840
Phone: 07 870 5200 Fax: 07 870 5300
7.07.01
7.03.02 7.14.09
7.03.01
24.21.03
50
1,542
1,920
50
24.21.01
24.10.10
18mm Grade BB plywood panel to
support hinged joint to shelving
unit. panel fixed to steel brackets
with 3/counter-sunk self-tapping
5mm machine screws to each
bracket. all exposed faces of
plywood to be clear finished.
24.10.11
25x25x2 SHS Steel brackets fixed
to wall at top, bottom and middle
of hinge panel to support hinge
panel and act as a stopper for the
hinging shelf unit. Open ends to
have caps welded in. To be
powder-coated to match shelving.
Fit thin (around 3mm - COS)
rubber stopper to side of outer
end. Fix to wall with 2/10mm
coach screws.
24.10.12
75mm hinges fixed to hinge panel
and end panel of shelf unit. 6 in
total - evenly spaced. Satin chrome
finish.
24.10.13
75mm braked caster wheels to
middle and outer single faced
posts (none to inner post as this is
supported by the hinged joint).
24.10.14
Precision 25x3mm steel cross
braces (92549) bolted to base of
single faced posts and to each
other at intersection point. Allow
to alter length as required for this 24.10.15
non-standard configuration.
Standard Precision powder-coated
steel shelf stripping fixed to wall.
Stripping height to match hinged
unit.
7.03.01
150x45 HySpan rafters at
900mm centres.
7.03.02
200x45 HySpan rafters at
900mm centres for spans over
4m.
7.07.01
70x45 H1.2 SG8 purlins at
900mm crs.
7.14.09
2/140x45 H1.2 SG8 nog
between rafters to provide fixing
for lighting bar below.
15.05.01
Armstrong RH99 fine fissured
1200x600mm ceiling tiles in
Rondo Duo 2-way exposed
suspended grid system. To be
hung raking at 150mm below
underside of roof structure.
15.05.07
Holes to be formed in edge of tile
for lighting bar supports.
15.05.07
24.21.02
X9
Lighting Bar Detail
scale 1:20
109
1,853
16. Wall Linings
200
318
376
24.10.11
24.10.09
24.10.08
24.10.15
24.10.04
24.10.06
24.10.05
24.15.02
24.10.08
24.10.04
1,924
24.10.05
24.10.07
16.12.02
Plan
24.10.06
24.10.06
24.10.07
24.10.07
16.12.02
24.10.05
24.10.13
X10 Hinged Library Shelving Detail
24.10.08
Section
scale 1:20
102
Autex Composition fixed over
plywood backing board.
24. Fittings
24.10.12
24.10.04
24.10.08
24.10.10
704
24.10.14
24.10.06
16.12.02
225
4,000
15.05.01
15.05.07
18mm Grade BB plywood end
panel fixed to single faced post
and base with counter-sunk selftapping 5mm machine screws at
150mm centres. all exposed
faces of plywood to be clear
finished.
15. Ceilings
3m to F.L.
213
24.10.09
7. Roof Structure
7.14.09
Precision 1815mm single faced
post (92706).
Precision powder-coated steel
shelving and end plates - refer to
shelving schedule for sizes and
types.
24.15.02
9mm grade BD plywood backing
board from shelving unit. Fix to
back edge of single sided posts
with couter-sunk self-tapping 5mm 24.21.01
machine screws at 200mm
centres. Grade B face is to be
exposed behind shelving and clear
finished. Grade D face to be on
back of unit.
24.21.02
40x20 aluminium trim to all four
sides of backing board (mitre at
corners). Powder-coat to match
shelving. Fix to side of single sided 24.21.03
posts with couter-sunk self-tapping
4mm screws at 600mm centres.
Precision powder-coated 305mm
steel canopy shelf on underlung
end plates.
Backs of the two shelving units
mounted on Southern wall are to
have J Roger Jenkins Ltd
1.8x1.2m whiteboards mounted
to top half of back panel..
50mm dia steel pipe welded to the
configuration shown to form
lighting bar. Open ends to have
caps welded in. Bar to be powdercoated.
Catenary wire run between
supports for lighting bar to
suspend cabling from.
Fix bar to nogs via 50x120x5
cleat fitted between nogs and
2/M12 bolts.
Contractor to verify and confirm on site all dimensions, levels, falls, heights, structure, services and notify Architect of any discrepancies in documents prior to commencement of works.
PROJECT TITLE:
Whatawhata School
New Roll Growth Spaces
Tender Set
REVISIONS:
DRAWING TITLE:
A Whiteboards added to backs of
southern units.
Details X9 & X10
DRAWN:
2/7/14
JOB NO.:
SHEET:
SCALE:
1:20 @A3
DATE:
26/6/14
www.gisler-architects.co.nz
MW
5270
CHECKED:
FILE: 5270 Whatawhata Roll Growth 2014 WD.pln
REVISION:
406 A
59 Bank Street, P O Box 297, Te Awamutu 3840
Phone: 07 870 5200 Fax: 07 870 5300
1. Important Notes
810
4,250
1,400
1,400
1,400
4,850
1,600
1,600
1.20.01 Check all dimensions on site prior to
manufacture.
20.03.01
1.20.02 All flashings and preparation
1.20.01 of openings to
comply
with NZBC E2/AS1.
20.03.04
1,600
700
20.03.05
20. Doors
2,100
700
D101, D103 & D105 -D112 are to be
20.03.01 Doors
20.03.07
exterior powder-coated aluminium doors with
glazed panels as indicated by 'G'. Stiles and Rails
to20.04.01
be commercial section with at least 2.0mm
wall thickness, 100mm thick rails and stiles and
20.05.02
stiles
deep enough to fit the Lockwood mortice
lock (86mm needed). Heavy domestic section is
not20.11.01
acceptable. An example of this is Vantage
Magnum
50.
20.11.03
20.03.04 Doors D102 & D104 Are to be powder-coated
20.11.05
aluminium
sliding doors with heavy domestic
section stiles and rails. Sidelights are to be
20.12.01
35mm
window section with fixed glazing and
awning sashes as indicated - all as per window
20.12.03
schedule.
and single exterior aluminium doors
20.03.05 All double
20.13.01
are to have full height aluminium flange fixed to
handle
side stile to protect lockset.
20.14.01
20.03.07 Side hung aluminium doors are to have no sill to
20.15.01
frame
- instead fix folded stainless steel
threshold bar to bottom edge (see detail).
20.04.01 Doors D151 & D152 are to be interior solid
core - paint quality doors (38mm wide leaf
minimum) with glazed panels as indicated.
Glazing to be beaded into holes cut into doors as
dimensioned. Glazing beads to be clears pine clear finished.
20.05.02 D153 & D154 are to be 'Transpace Spaceseal'
501 operable acoustic wall with a Jamb Hinged
Passage Door as shown (see floor plan for
handing of passage door). Install to
manufacturers requirements. To have a 45 STC
rating and have Autex Compostion installed to
both sides of operable wall configuration.
20.11.01 All exterior aluminium door liners are to be Ex
25mm grooved clears pine - clear finished.
20.11.03 All interior door liners are to be Ex 50mm solid
rebated grooved clears pine - clear finished (as
detailed). Planted stops are not acceptable.
20.11.05 All interior transpace door trims are to be Ex
35mm (25mm finished) grooved clears pine clear finished. Refer to detail.
20.12.01 All exterior glass is to be double glazed. The
configuration of glass is toughened glass to the
exterior and laminated safety glass to the
interior.
20.12.03 All interior glass is to be laminated safety glass.
20.13.01 All door handles are to be mounted 1000mm
above floor level. Refer to Hardware Schedule
for hardware to install.
20.14.01 All doors (interior and exterior) are to have 4
hinges, 2 at the top, 1 in the middle and 1 at the
bottom.
20.15.01 All doors are to be fixed to timber framing with
6mm CS wood screw through timber packers
(nail fixing is not acceptable).
700
D101, D103, D105
X5
D102
D104
405
810
810
710
710
710
150
510
810 310
150
X6
D106
D107, D108
D109, D111
400
D110, D112
405
7,780
966
966
966
710
966
966
966
966
966
25
2,825
2,075
D153, D154
C3
403
D151
D152
Door Hardware Schedule:
Hardware:
Door
Qty (per door)
D101, D103,
D105
Lockwood 3572Z-R or L lockset - Master keyed.
Legge Alpha 702 furniture to exterior.
Legge Alpha 712 furniture to interior.
Lockwood 7726SRH door closer with hold-open.
1
1
1
1
D102, D104
25
25
320
218
700
400
404
218
2,100
X7
2,100
2,100
700
218
700
300 25
810
Interlock Albany 182000 sliding door lockset
1
D106
Lockwood 3572Z-R or L lockset - Master keyed.
Legge Alpha 702 furniture to exterior.
Legge Alpha 712 furniture to interior.
Ryobi RB20 flush bolts to secondary leaf.
D&W 131 12 SC CF dust socket
Devon DV87 pedestal latchback.
1
1
1
2
1
2
D107 - D112
Lockwood 3572Z-R or L lockset - Master keyed.
Legge Alpha 702 furniture to exterior.
Legge Alpha 712 furniture to interior.
Devon DV87 pedestal latchback.
1
1
1
1
D151
Lockwood 3572Z-R or L lockset - Master keyed.
Legge Alpha 702 furniture to exterior.
Legge Alpha 712 furniture to interior.
Devon Saturn door stop.
1
1
1
1
D152
Lockwood 3572Z-R or L lockset - Master keyed.
Legge Alpha 702 furniture to exterior.
Legge Alpha 712 furniture to interior.
D&W 1240 150 SC flush bolts to secondary leaf.
D&W 131 12 SC CF dust socket.
Devon Saturn door stop.
1
1
1
2
1
2
1.20.02
Important Note:
- All locksets listed in the Hardware Schedule as
being 'Master-keyed' are to be keyed to schools
existing master key system. Allow $40 per door.
Systems and levels of access is to be determined
during construction.
Contractor to verify and confirm on site all dimensions, levels, falls, heights, structure, services and notify Architect of any discrepancies in documents prior to commencement of works.
PROJECT TITLE:
Whatawhata School
New Roll Growth Spaces
Tender Set
REVISIONS:
DRAWING TITLE:
A Hardware D101, D103 & D105
changed
Door Schedule
DRAWN:
2/7/14
JOB NO.:
SHEET:
SCALE:
1:50 @A3
DATE:
26/6/14
www.gisler-architects.co.nz
MW
5270
CHECKED:
FILE: 5270 Whatawhata Roll Growth 2014 WD.pln
REVISION:
501 A
59 Bank Street, P O Box 297, Te Awamutu 3840
Phone: 07 870 5200 Fax: 07 870 5300
1. Important Notes
1.21.02
1,600
2,400
600
2,400
700
21.03.01
W101
W102
W103
C4
W104
3,000
700
400
21.04.10
21.06.01
700
1,400
1,700
2,100
21.03.05
600
2,300
1,800
2,400
21.03.04
1,200
403
W105
W106, W107
W108, W109
21.06.06
W151
B1
500
2,400
21.07.01
500
402
2,400
21.07.05
21.25.01
2,700
3,200
21.07.10
3,150
3,650
Check all dimensions
on site prior
1.21.02
to manufacture.
All flashings and preparation
21.03.01 of
openings to comply with NZBC
21.03.04
E2/AS1.
21.03.05
21. Windows
700
2,100
700
1.21.03
1.21.03
W201, W202, W203
21.04.10
Windows W101 - W109 &
W201 - W205 are21.06.01
to be exterior
powder-coated aluminium
windows - 35mm section
with
21.06.06
sashes and fixed glazing as
21.07.01
indicated by 'F'. Sliding
panels to be
constructed with Domestic ranch
slider door section21.07.05
and frame.
All exterior aluminium
window
21.25.01
awning sashes are to have a pair
21.07.10
of wedgeless fasteners
and a pair
of concealed stainless steel
restrictor stays.
All exterior aluminium window
sliding sashes are to have
Interlock Albany 182000 locksets.
W151 is to be a frameless Shugg
bottom hung vertical sliding
window sliding into wall cavity
above.
All exterior aluminium window
liners are to be Ex 25mm grooved
clears pine - clear finished.
Shugg window to have Ex35mm
pine clears grooved liners, clear
finished, to head and jambs. Head
liner to be split as shown to allow
operation of window.
All exterior glass is to be double
glazed. The configuration of glass
is toughened glass to the exterior
and laminated safety glass to the
interior.
All interior glass is to be
toughened safety glass.
W106, W107, W108 & W109
are to have obscure glazing.
W201-W205 are to have
Interlock Elevations electrically
operated winding gear. Allow for
two motors to each sash (refer to
electrical plan). Sahses to have
frictionless stays.
W204, W205
Contractor to verify and confirm on site all dimensions, levels, falls, heights, structure, services and notify Architect of any discrepancies in documents prior to commencement of works.
PROJECT TITLE:
Whatawhata School
New Roll Growth Spaces
Tender Set
REVISIONS:
DRAWING TITLE:
A Obscure glass to W106-109.
Winding gear to upper windows.
Window Schedule
DRAWN:
2/7/14
JOB NO.:
SHEET:
SCALE:
1:50 @A3
DATE:
26/6/14
www.gisler-architects.co.nz
MW
5270
CHECKED:
FILE: 5270 Whatawhata Roll Growth 2014 WD.pln
REVISION:
502 A
59 Bank Street, P O Box 297, Te Awamutu 3840
Phone: 07 870 5200 Fax: 07 870 5300
815
510
2,750
100
17. Floor Coverings
510
815
17.03.25
2,400
18.08.HC
100
80
600
355
400
320
145
18. Plumbing & Drainage
23.03.01
18.08.HC
17.03.25
23.04.01
U106 Music Storage Unit 1
Plan
17.03.25
23.03.05
23.04.07
25
23.03.01
23.03.05
23.03.01
25.11.02
750
607
607
750
23.04.07
18
23.04.08
23.10.05
36mm Formica bench top with
rolled front edge. All other edges
to be square.
150mm Formica upstand to back
and side of bench formed with
bench top.
18mm Melteca Melamine
cabinetry with 2mm Meltrim
edging. Carcass to be white,
exposed surfaces coloured.
Cupboards to have 1 adjustable
shelf if not noted otherwise.
Open shelves are to be adjustable
25mm Melteca with 2mm PVC
edging (coloured, not white).
Centre shelf to be fixed.
All cabinet handles to be Sylvan
SB128/SCP.
775
25. Sanitary Hardware
25.03.01
25.11.02
Greens Marketti Blade sink mixer.
Mercer Riva 316 stainless steel
sink insert (1x bowl 510x355x180mm deep). Top
mount.
150
150
294
714
180
120
36
120
150
18
23.10.05
2,100
25.03.01
1,150
23.04.01
23.03.05
Under-bench HWC: Rheem 25L
mains pressure under-bench unit
with Delabie Premix 733020
water mixer. (HWC is 405mm dia
x385mm high). Connect to sinks
as indicated. Provide overflow pipe
to exterior.
23. Joinery
23.04.08
25.11.02
U105 Sink Bench
Plan
900
Cove vinyl up unit toe boards.
U105 Sink Bench
Front Elevation
23.04.01
18.08.HC
17.03.25
U106 Music Storage Unit 1
Front Elevation
17.03.25
23.04.01
Contractor to verify and confirm on site all dimensions, levels, falls, heights, structure, services and notify Architect of any discrepancies in documents prior to commencement of works.
PROJECT TITLE:
Whatawhata School
New Roll Growth Spaces
Tender Set
REVISIONS:
DRAWING TITLE:
Joinery Schedule: U105 & U106
A U106 changed.
DRAWN:
2/7/14
JOB NO.:
SHEET:
SCALE:
1:20 @A3
DATE:
26/6/14
www.gisler-architects.co.nz
MW
5270
CHECKED:
FILE: 5270 Whatawhata Roll Growth 2014 WD.pln
REVISION:
504 A
59 Bank Street, P O Box 297, Te Awamutu 3840
Phone: 07 870 5200 Fax: 07 870 5300
2,400
17. Floor Coverings
17.03.25
21.04.10
80
500
17.03.25
23.04.01
U107 Music Storage Unit 2
Plan
1,539
23.10.02
1,496
22.01.01
23.04.07
1,150
500
17.03.25
23.04.07
22.01.01
23.04.08
23.10.02
160
317
23.10.05
50
350
25
2,100
600
23.04.01
21.04.10
1,200
1,071
750
1,100
23.03.01
1,521
23.03.01
551
680
23.10.11
1,751
150
23.04.01
23.03.01
22.01.01
150
760
394
180
36
23.04.01
36mm Formica bench top with
rolled front edge. All other edges
to be square.
18mm Melteca Melamine
cabinetry with 2mm Meltrim
edging. Carcass to be white,
exposed surfaces coloured.
Cupboards to have 1 adjustable
shelf if not noted otherwise.
Open shelves are to be adjustable
25mm Melteca with 2mm PVC
edging (coloured, not white).
Centre shelf to be fixed.
Power points mounted in back of
unit.
All cabinet handles to be Sylvan
SB128/SCP.
80mm PVC 'cable-tidy' insert into
bench top. Client to confirm
location prior to installation.
U108 Librarian's Workstation
Plan
23.10.05
17.03.25
Returns slot through wall into
joinery unit in Library Office. Refer
to detail.
23. Joinery
2,021
23.04.01
23.10.11
U107 Music Storage Unit 2
Front Elevation
W151 is to be a frameless Shugg
bottom hung vertical sliding
window sliding into wall cavity
above.
22. Internal Trims
25
23.04.08
Cove vinyl up unit toe boards.
21. Windows
95
370
450
18
600
502
80
U108 Librarian's Workstation
Front Elevation
17.03.25
Contractor to verify and confirm on site all dimensions, levels, falls, heights, structure, services and notify Architect of any discrepancies in documents prior to commencement of works.
PROJECT TITLE:
Whatawhata School
New Roll Growth Spaces
Tender Set
REVISIONS:
DRAWING TITLE:
Joinery Schedule: U107 & U108
A U107 & U108 changed.
DRAWN:
2/7/14
JOB NO.:
SHEET:
SCALE:
1:20 @A3
DATE:
26/6/14
www.gisler-architects.co.nz
MW
5270
CHECKED:
FILE: 5270 Whatawhata Roll Growth 2014 WD.pln
REVISION:
505 A
59 Bank Street, P O Box 297, Te Awamutu 3840
Phone: 07 870 5200 Fax: 07 870 5300
Interior Finishes Schedule:
Room:
15. Ceilings
Boys Change,
Girls Change
Boys WC, Girls
WC
13mm Gib board fixed to 75x40
ceiling battens at 600mm crs.
Stop to a level 4 finish and paint.
13mm Gib board fixed to 75x40
ceiling battens at 600mm crs.
Stop to a level 4 finish and paint.
16. Wall Linings
17. Floor Coverings
12mm Plywood Grade BD
direct fixed to wall framing with
close V-Butted joints. Clear
finish.
22. Internal Trims
23. Joinery
Sika Sikafloor-261 NS heavy duty self
levelling epoxy resin floor covering
(3mm thick). To be installed by
approved installer to manufacturers
instructions.
Cove Sika Sikafloor-261 NS up walls
150mm.
40x10mm clears pine coving
bead at 150mm from FL.
40x10mm clears pine scotia.
10mm Gib board base lining
direct fixed to framing. Stop to
a level 2 finish.
4.5mm Hardieglaze with white
pvc jointers fixed over base
lining from 150mm to ceiling.
Cove vinyl up walls 150mm.
Tarkett Granit vinyl direct stuck.
40x10mm clears pine coving
bead at 150mm from FL.
40x10mm clears pine scotia.
24. Fittings
None.
25. Sanitary Hardware
Timber slat, wall mounted seats (refer to
detail).
2x
2x
None.
Resco 5000 series toilet partitions with
associated doors and hardware.
Configuration as per floor plan.
2x
2x
2x
Delabie DE709000 'Round' vandal proof wall mounting
shower head, with an adjustable scale-proof nozzle and
fixed 6 L/min flow-restrictor. Body in chrome plated
brass with anti-rotating stop lug.
Delabie DE790220 automatic 30s shut-off delayed
shower mixer including a chrome plated brass plate
160x220mm, in water proof recessing box, with stop
cocks.
Delabie Tempostop AB Standard self-closing tap (premixed water).
Mercer G7 stainless steel wash hand basin on
mounting bracket (355x355x120mm deep).
Caroma Concorde toilet suite.
Classroom,
Library/MP
Room, Issues/
Librarian
Armstrong RH99 fine fissured
1200x600mm ceiling tiles in
Rondo Duo 2-way exposed
suspended grid system. To be
hung raking at 150mm below
underside of roof structure.
10mm Gib board base lining
direct fixed to framing. Stop to
a level 3 finish.
Autex Composition over base
lining from 190mm to ceiling.
Autex Avondale carpet direct stuck to
slab.
Cove carpet up walls 150mm.
Autex widetrack carpet direct stuck.
Ribs to direction shown.
40x10mm clears pine coving
bead at 150mm from FL.
U101 & U102 in
Classroom.
U107 in Issues/Librarian.
Adjustable shelving with powder-coated None.
steel shelves. Refer to details and schedule.
Whiteboard storage unit from Mike's
Woodshop. 3.6m wide with modules D, B &
D as indicated.
Powder-coated steel lighting bar
Breakout Room
Armstrong RH99 fine fissured
1200x600mm ceiling tiles in
Rondo Duo 2-way exposed
suspended grid system. To be
hung raking at 150mm below
underside of roof structure.
10mm Gib board base lining
direct fixed to framing. Stop to
a level 3 finish.
Autex Composition over base
lining from 190mm to ceiling.
Cove carpet up walls 150mm.
Autex Avondale carpet direct stuck to
slab.
40x10mm clears pine coving
bead at 150mm from FL.
None.
J Roger Jenkins Ltd 1.5x1.2m whiteboard
with pen rail.
Breakout Room
Kitchen/Wet
Area
Armstrong RH99 fine fissured
1200x600mm ceiling tiles in
Rondo Duo 2-way exposed
suspended grid system. To be
hung raking at 150mm below
underside of roof structure.
10mm Gib board base lining
direct fixed to framing. Stop to
a level 2 finish.
4.5mm Hardieglaze with white
pvc jointers fixed over base
lining from 150mm to ceiling.
Cove vinyl up walls 150mm.
Tarkett Granit vinyl direct stuck.
40x10mm clears pine coving
bead at 150mm from FL.
U103, U104 & U105
None.
1x
2x
Music Store
Armstrong RH99 fine fissured
1200x600mm ceiling tiles in
Rondo Duo 2-way exposed
suspended grid system. To be
hung raking at 150mm below
underside of roof structure.
10mm Gib board lining direct
fixed to framing. Stop to a level
4 finish and paint.
Cove vinyl up walls 150mm.
Tarkett Granit vinyl direct stuck.
40x10mm clears pine coving
bead at 150mm from FL.
U106 & U107.
None.
None.
None.
Greens Marketti Blade sink mixer.
Mercer Riva 316 stainless steel sink insert (1x bowl 510x355x180mm deep). Top mount.
Important Notes:
All clears timber trims are to be clear finished.
All timber trim heights specified are to be to the bottom edge.
Rebate timber trims where necessary to fit over vinyl/hardieglaze.
Composition, hardieglaze and floor coverings are to be omitted behind joinery units.
All vinyl with coving is to have internal and external butterfly welds.
Exterior Finishes Schedule:
Element:
Material:
Finish:
5. Foundations
Poured in-situ slab footing.
Plaster smooth and paint
7. Roof Structure
Steel verandah frames.
Hot-dip galvanised
9. Roofing
0.55 gauge trapeziodal Colorsteel Endura roofing.
Factory pre-finished
125mm square Colorsteel Endura guttering.
Factory pre-finished
Ex 25mm H3.2 timber fascia and barge boards.
Painted
9mm James Hardie 'Titan' facade panel.
Painted
6mm Hardieflex soffit linings with uPVC jointers.
Painted
H3.2 soffit beads.
Painted
18. Plumbing & Drainage
100mm uPVC DP.
Painted
20. Doors
Exterior aluminium doors.
Factory powder-coated
21. Windows
Exterior aluminium windows.
Factory powder-coated
10. Claddings
Contractor to verify and confirm on site all dimensions, levels, falls, heights, structure, services and notify Architect of any discrepancies in documents prior to commencement of works.
PROJECT TITLE:
Whatawhata School
New Roll Growth Spaces
Tender Set
REVISIONS:
DRAWING TITLE:
A Music Store walls changed.
Finishes Schedule
DRAWN:
2/7/14
JOB NO.:
SHEET:
SCALE:
1:1 @A3
DATE:
26/6/14
www.gisler-architects.co.nz
MW
5270
CHECKED:
FILE: 5270 Whatawhata Roll Growth 2014 WD.pln
REVISION:
506 A
59 Bank Street, P O Box 297, Te Awamutu 3840
Phone: 07 870 5200 Fax: 07 870 5300