MANUFACTURERS OF QUALITY AGRICULTURAL EQUIPMENT SINCE 1936 OPERATOR’S MANUAL AND PARTS LISTING FOR THE HDD Series Closed End Sections VERSION: 5-03AJF TO THE OWNER AND OPERATORS Before assembling or operating this unit, READ THIS MANUAL THOROUGHLY. To obtain the best performance of the unit, familiarize yourself with each component and adjustment. Store this manual where it can be readily available for future reference. In the event that the harrow or any part of the unit should be sold, be sure that the new owner receives a copy of this manual for their reference. 1330 DALLAS STREET, P.O. BOX 100 SAUK CITY, WISCONSIN 53583 PHONE: (608) 643-3321 TOLL FREE: (800) 627-8569 FAX: (608) 643-3976 Assemble the Harrow Sections The sections come in three different widths, 4’, 6’ and 8’. Determine which section your harrow requires and follow the assembly instructions below. Refer to figure below. 1. Assembly of 4’ sections. Place one left sidebar runner and one right sidebar runner on the ground about 4 feet apart. Insert a ½” x 2” bolt through the retainer washer and through the tooth bar. Place a bushing on the bolt and insert the bolt through the runner and fasten with a lock washer and hex nut. Repeat this for the other five bolts. 2. Assembly of 6’ and 8’ sections is the same as the 4’ sections with the following changes. Use two right hand sidebar runners and one left hand per section. To attach the center runner, use three ½” x 3” bolts, with a washer on the outside of each tooth bar. 3. Attach the spring teeth. Refer to page 4 for proper tooth spacing. Measurements shown are from the inside of the end plate for the tooth bar. Teeth should measure 12” on centers. Teeth are mounted to the bars with a tooth mount clip. Hook clip over tooth bar and insert tooth through slot. Secure with a ½” x 3-1/2” bolt, lock washer and lock nut. 4. Attach lever assemblies to sections. They should be mounted approximately in the center of the sections, with the handle to the rear. Attach them with six ½” x 3 1/2” bolts, lock washers and hex nuts per assembly. TOOTH CLIP 1/2 X 3 1/2 BOLT, LOCK WASHER AND LOCK NUT 1/2 X 3 BOLT 1/2 X 2 BOLT RETAINER WASHER BUSHING RETAINER WASHER BUSHING RETAINER WASHER LOCK WASHER AND HEX NUT LOCK WASHER AND HEX NUT 2 1/2 x 3 1/2 BOLTS, LOCK WASHERS AND HEX NUTS HDD-030 AND HDD-040 Parts Diagram and Listing 15 1 14 16 1 13 17 9 12 11 8 10 5 2 7 4 3 6 ITEM # 1 2 3 4 5 6 7 8 8 9 10 11 * 12 13 * 14 15 16 17 * Note: Diagram shows two HDD-030 sections (one 6’ section) PART # DESCRIPTION HDD-013 RIGHT SIDE BAR RUNNER HDD-010 FRONT WEAR SHOES ** 3/8” X 1” COUNT SUNK BOLT HDD-014 RUNNER WEAR PLATE HDD-044 HARDENED BUSHING HDD-016 RETAINER WASHER ** ½” X 2” GR. 5 BOLT HDD-020 HARROW BAR (HDD-030) HDD-022 HARROW BAR (HDD-040) ** ½” X 2 ¾” GR. 5 BOLT HDD-026 LEVER HANDLE ONLY HDD-024 LEVER PULL ROD SA-102 PULL ROD SPRING HDD-028 CENTER BAR HDD-031 POCKET CP-5312 5/32” X 1 ¼” COTTER PIN HDD-041 POCKET CLAMP PLATE HDD-012 LEFT SIDE BAR RUNNER HDD-505 SPRING TOOTH HDD-038 TOOTH MOUNT CLIP HDD-027 LEVER HAND ASSEMBLY * Unnumbered items are not pictured. ** Please specify model number when ordering these parts. 4/16/01 3 HDD SECTION LAYOUT 4