1. P lease study the instruction manual before your applications and keep it for your future reference. 2. Do not flash LED light directly on the eyes when LEDs are on. 3. Do not install the camera on a unstable surface. It will cause falling or other hazards. 4. Do not use improper power, it could cause fire or electric shock. 5. Do not disassemble or remodel the camera, it could cause fire, electric shock or other hazards. 6. Stop using the camera when you find a malfunction like smoke or unusual heat, it could cause fire or electric shock. 7. Due to the possibility of water leakage, do not cut or peel off the cable. In case you cut or peel off the cable, the warranty will be void. 8. Do not adhere dangerous articles to the camera. 9. Do not leave the unit along with an unstable stand or table. 10. D C power cable or Video cable should be always loose. Do not keep the cables tight or twisted. 11. P lease use the camera unit within given temperature and electricity limit. 12. P lease make sure that installation should be done by qualified service person only. 13. D o not disassemble the unit by yourself. When there is problem with the unit please contact after-sale service center or the shop where you bought. 14. S top operating and separate connector from the unit if below cases happen. - When power connector or video connector is broken. - When body is broken and dropped. - When it is not operating though it is set correctly by the manual. ※ If you meet any strange cases, please call the shop where you purchase If the product is to be put out of operation definitively, take it to a local recycling plant for a disposal which is not harmful to the environment. 1. Supreme Resolution(700 TV-Line) 2. This product is suitable for 24 hours survillance with optical multicoating filter according to IR LED and CCD. 3. The light of IR LED can reach about 100m away.(Indoor) 4. LED can be ON/OFF automatically by photoconductive sensor to perceive the light condition in the circumstance. Under 5 lux do LEDs turn on. 5. This product is waterproof to resist rain, snow and other weather factors.(IP63) 6. This product is made of aluminum material with corrosion-free surface to resist rust and corrosion for a long time. 7. Sunvisor of this product can help the camera get the picture clearly. DIMENSION Model No. SK-P901D/M556AI Image Sensor 1/3" COLOR SONY SUPER HAD CCDⅡ Effective Pixel 976(H) x 494(V) Pixel(NTSC), 976H) x 582(V) Pixel(PAL) Resolution TV Type Sync. Type Video Output Min. Illumination S/N Ratio 220 340 SK-P901/M556AI Gain Control 700 TV-Line NTSC, PAL Internal 2:1 Interlace 1Vp-p(Sync,Negative) Termination 75Ω γ= 0.45 Typ. 0Lux(LED ON) - 100M Range 141 Day&Night 52dB or More(AGC OFF) 62.8 CAUTION AND WARNING SPECIFICATION FEATURE 99 IR OUTDOOR HOUSING CAMERA SK-P901(D)/M556AI MANUAL 87.9 137.5 Shutter Speed Scanning System Gamma Characteristic CONFIGURATION Test Illuminance Area VIDEO CABLE 12V DC/24V AC Type -non polar 1/60(1/50) ~ 1/100,000sec. Average test illumination by front view IR LED 83EA LENS Vari-focal auto iris Lens Current Consumption 12V DC Type -12DCV AUTO(Electronic) LED Power Supply POWER CABLE Automatic gain control Regulated 12V DC ±10% 12V DC/24V AC Dual voltage Max. 850mA(at DC12V, LED ON) Operation Temp. -10℃ ~ 50℃ Preservation Temp. -20℃ ~ 60℃ Dimension Weight 141(W) x 100(H) x 340(D)mm Approx. 1,300g FUNCTION SETTING Select Menu 1. How to use the jog lever BLC 6 Sub menu Summary Select Menu Adjust the brightness 8. FUNCTION AREA Set up the area of using BLC MOTION Motion detection GAIN The lower the GAIN lever is the masking is corvered on low on low illuminations PRIVACY Privacy mask D-EFFECT D-ZOOM DIS FREEZE MIRROR NEG.IMAGE IMAGE ADJ SHARPNESS MONITOR LENS Adjust image in the Screen SHADING DEFFECT COMM ADJ CAM TITLE PROTOCOL CAMERAID BAUD RATE MODE HSBLC 5 3 1 ①SET : Used to access the menu and confirm selection. ②UP, ③DOWN : Used to move the cursor to up or down. ④LEFT, ⑤RIGHT : Used to move the cursor to left or right and change the value. ⑥EXT-VIDEO : Extra video output terminal for installation. Plug your test monitor in hear. The cable is option. MASK-LEVEL Adjust the brighthness on the selected area M.SKIP AREA Adjust the selected area not to get masked by HSBLC 4. WHITE BAL ATW 2,500°K ~ 9,500°K AWB 1,800°K ~ 10,500°K AWC->SET To find the optimal luminance lever for the current environment, point the camera towards a sheet of white paper and press the set button. MANUAL Adjust the proportion for RED and BLUE 2. OSD menu structure Select Menu Sub menu Summary 1.LENS MANUAL DC BRIGHTNESS 5. DAY & NIGHT BRIGHTNESS BW VIDEO AUTO 2. EXPOSURE SHUTTER SENS UP FLICKERLESS mode MANUAL Adjust shutter manually VALUE Adjustlevel of this function SMART NR Set the fuction to “ON” or “OFF” LOW SMART LEVER Adjust the level of this function MIDDLE SENSITMTY Adjust the sense of this function LEVEL Adjust F-DNR lever ON HIGH OFF OFF 7. F-DNR AUTO SYNC Option LANGUAGE Select the language SAVE Save & Exit RESET Set as a default CANCEL No Save & Exite 6. SMART 3DNR FLK OFF AGC Option ※ This camera : Use EXT mode EXT AUTO Additional digital function activated 9. EXIT COLOR IRIS SPEED Summary VALUE 2 4 Sub menu ×2 ~ ×256 3. BACKLIGHT MANUAL OFF LOW LEVEL In WDR mode, AGC in low HIGH LEVEL In WDR mode, AGC in high DWDR AUTO COLOR GAIN Adjust COLOR GAIN lever EDGE GAIN Adjust the lever of this function GAMMA Adjust GAMMA DETECT LEVER Adjust lever of detect ※All specification is subject to change without notice to improve the quality. 3B26140A
© Copyright 2024