Download Report

INSTALLATION
ALIS Induction
PowerMANUAL
TM
www.agrilamp.com
TECHNICAL INFORMATION
Light Source
8W High Power LED
Luminous Flux
550 lumens (8W ALIS-Luminaire)
Optics
Optical grade milky white standard
and tulip polycarbonate lens
Connection Type
Clip on
Dimmer Option
100K potentiometer or 0-10V
Rating
IP65
Rated Life
40,000 Hours
WORKING ENVIRONMENT
Ambient Temperature
-20 to +55 C
Humidity Range
0 to 95%
o
BENEFITS
DISCLAIMER
• Simple to Install and Reposition
• Ultra Safe - Total Over Voltage Protection
• Minimum Harmonic Distortion
• Maximum Power Factor
• Zero Inrush Current
• Smooth Dimming Effect
• Humidity Proof; Dust-proof; Shatterproof
• Completely Waterproof with an IP65 rating
These instructions are provided for information only
Installation should be carried out by an experienced professional
All work should be verified as meeting local and international
electrical, health and safety standards
Greengage Lighting Ltd are not responsible for safety on site
and installers should contact Greengage Lighting Ltd technical
support for any queries ([email protected])
ALIS Induction Power
TM
ELECTRICAL SPECIFICATION
Input Voltage
www.agrilamp.com
220/240Vac 50/60Hz
TABLE OF CONTENTS
Maximum ALIS Power Consumption 500W
1.
Power Factor
>0.95
2. INSTALLATION PROCEDURE
Total harmonic distortion
<20% nominal
3. POST-INSTALLATION
Final Specifications subject to change. © Copyright AgriLampTM 2014. All rights reserved.
ALIS PACKAGE
Final Specifications subject to change. © Copyright AgriLampTM 2014. All rights reserved.
1
ALIS PACKAGE
The ALIS Package contains:
• Power Hub (PH500)
• ALIS - Dimmer
• ALIS - Dimmer Pot
• ALIS - Bus
• ALIS - Luminaires
• ALIS - IDC Termination
• ALIS - BUS Connector
2
INSTALLATION PROCEDURE
Tools required for installation
• Screw driver
• Set of pliers
• Wire stripper
• Wire cutter
Remove the products from the box and follow these instructions.
a. Measure the size of the barn ALIS to be installed and cut the
ALIS-Bus to required size.
b. Terminate the open end of the ALIS-Bus
with the ALIS-IDC. Insert the two open ends of
the ALIS-Bus into the ALIS-IDC as shown in
figure1. Crimp the ALIS-IDC with a slip joint Pliers.
figure1
c. Attach the ALIS-Bus into the installation position. Ideally,
attach to the support that the ALIS-Luminaires will be supported
(e.g. steel cable).
d. Determine the number of ALIS-Luminaires required to
light the barn and the distance required between each ALISLuminaire for even lighting dispersion. A distance of 2.2-2.8m is
recommended between two ALIS-Luminaires.
e. Clip ALIS-Luminaire onto the ALIS-Bus.
This is done buy opening the ALIS-Luminaire and placing
the ALIS-Bus cable in the Coupler Housing as shown in figure 2.
When the ALIS-Bus sits properly in the twin troughs in the
Coupler Housing, press the lid onto ALIS-Bus and snap closed.
Please ensure that the ALIS-Bus cable is not caught when closing
the Coupler. Check figure 3. (Apply silicon grease between the two
gaskets mating area to achieve IP65 ).
figure2
figure3
f. Clip on all the ALIS-Luminaires required onto the ALIS-Bus.
g. Install the Power Hub in a cool and dry location.
The ALIS power hub and dimmer must be enclosed within a
waterproof and dustproof enclosure.
h. Connect the ALIS-Bus to the ALIS-Dimmer. If dimming is not
required, connect the ALIS-Bus to the Power Hub (PH500).
i. Connect the ALIS-Dimmer to the Power Hub.
j. If dimming is required, connect the selected dimming control
to be the ALIS-Dimmer. Dimming is possible via either an ALISDimmer Pot (provided) or an 0 - 10V DC supply
Power Hub
(PH500)
Connection Diagram
Two IDC connectors are provided for the 0-10VDc connection.
Follow the instruction below on how to connect your 0-10VDc
cable to the connector.
• Insert the wire until it reached the end. Check figure4 and
figure5 ( Applicable wire size AWG 24-20).
ALIS-Dimmer
• Make Insulation displacement connection by crimping
down the connector. Use a plier at its open jaw condition.
Check figure6 and figure7.
figure4
figure5
figure6
figure7
Confirm that it is correctly locked
(Two locking mechanisms on both sides)
• The polarity of the 0-10VDc connection
is shown in figure 8.
ALIS-Dimmer
Pot
figure8
Note: Multiple ALIS-Dimmers can be
controlled with a single ALIS-Pot
or 0-10V DC supply.
(Please contact [email protected] for any
additional information as required)
ALIS-Bus
(available in
different length)
k. Connect the Power Hub to the mains supply.
l. Switch the power ON and the ALIS-luminaire will illuminate
(Luminous intensity goes to full brilliance at switch ON, before
settling to the controlled intensity on the ALIS-Dimmer Pot or
0-10VDc).
3POST-INSTALLATION
If the ALIS-luminaires are flashing ON and OFF, this means you have
too much load on the system. Start unclipping the ALIS-Luminaires
one at a time until the flashing stops.
Please note, if there is any need to extend the ALIS-Bus, the ALISIDC can also be used to connect two ALIS-Buses together.
ALIS-Luminaires
(Standard lens
and/or Tulip lens)
ALIS-IDC
Termination
The AgriLamp Induction System (ALIS) is a ‘CONTACTLESS’ power
technology that allows LED fixtures (ALIS-Luminaires) to be clipped
onto the cable (ALIS-Bus) without physical connection.
It works on the principle of distributing a highly regulated and
safe intermediate frequency alternating current (IFAC) over the
ALIS-Bus to the ALIS-Luminaire. The product is suitable for indoor
and outdoor use.
This document serves as a guideline for an ALIS installation in a
barn. Users should follow all relevant electrical standards when
carrying out the installation.
ALIS-Bus
Connector