Rotary Driver for Automatic Gate AN1２　Instruction manual　指导书 Mechanical and Electrical installation 机械与电路的安装 PAGE 1 Main housing Main motor 外壳马达 Stopper plate Stopper long bolt 制动片制动螺母 C-channel base C－槽底座 Wall bracket 墙壁托架 C-channel C－槽 Expansion bolt 外张螺栓 Drive bar 驱动杆 (not included)（不包括） (with left and right type) （分左右两类） PAGE 2 1 Install the C-channel base 安装　C-槽　底座 64.5 cm ２Make a mark on the wall 在墙上做记号 reference point 参考点 reference point 参考点 Make a mark on the wall 在墙上做记号 3 Install the wall bracket 安装墙壁托架让小洞对准记号 Align the hole to the mark PAGE 3 4 Install the wall bracket 安装墙壁托架电线出口 Wire outlet 请确保墙壁托架的平水 Wire Align the wall bracket to the water level 电线 5 Install the motor 安装马达 1 2 3 6 Install the motor 安装马达 Secure the C-channel by fastening the screw 以螺栓把　C－槽　固定 PAGE 4 ７Adjust the open and close position 调整开与关的停止位置 Adjust the stopper nut to contact with the stopper plate 调整制动螺母与制动片的接触点螺母　供螺母　供位置控制用位置控制用 Long nut, for position control use 关门位置开门位置 Close position Open position 8 Connect the electric cable 将电缆连接上 Beware! 注意！ Make sure you notice there are 3 point to align before you can close the housing properly C B Turn the lever to align A 旋? ? ? ? (Note: “A” not applicable for model AL) 要把外壳盖上时，注意有三个点必须对齐 9 Put on the housing 把外壳盖上 A B Fasten the ‘A’ ‘B’ screw 锁紧　A　B　两颗螺丝 Completed PAGE 5 完成 * The motor can be installed at any height level 马达可安装於任何高度 ** The C-channel can be installed onto a curve surface C－槽也可以装到弧形表面上 level 请确保　C－槽　底座的垂直水平 Please ensure the vertical level of the C-channel base PAGE 6 Solar Panel Electrical connection diagram for model: <Rotary Driver for Automatic Gate> using control panel MD-8285 Antenna Note: Due to our continuos improvements, the content may be different from the actual one Note: Remote control receiver AC - DC stepdown transformer (Hybrid mode control) Use either solar panel or transformer Do not use both at 1 time Red Black Use high current capacity cable for electric motors Indoor (open / close) Outdoor ‘Close Only’ Photo sensor (for lamp control) DC 12V Piezzo Siren Lamp Relay (DC12V) (use only specified siren) Auto Lock GBS-128RX GBS-125TX Motor B Motor A NOTE: The INFRARED BEAM is switched off automaticaly when the gate is close. If need to ON it for test purchase, open the gate or ARM the alarm PAGE 7 Pairing the remote control with the control panel 遥控器与控制板进行配对 During programming the remote control use the button to select the function (Side B restricted) for swing gate for folding gate Remote Control GFM-925AL GFM-925AL GFM-925W MD-8285-AL www.dcmoto.my Set for GFM925W model Set for GFM925AL model (Folding Type) Set for GFM925AL model (Swing Type) PAGE 8