1. No category

INSTALLATION MANUAL
Version 1.1 - April 2014
INSTALLATION MANUAL Epsio Zoom 1.1
Copyright
EVS Broadcast Equipment SA– Copyright © 2014. All rights reserved.
Disclaimer
The information in this manual is furnished for informational use only and subject to
change without notice. While every effort has been made to ensure that the information
contained in this user manual is accurate, up-to-date and reliable, EVS Broadcast
Equipment cannot be held responsible for inaccuracies or errors that may appear in this
publication.
Improvement Requests
Your comments will help us improve the quality of the user documentation. Do not
hesitate to send improvement requests, or report any error or inaccuracy on this user
manual by e-mail to [email protected].
Regional Contacts
The address and phone number of the EVS headquarters are usually mentioned in the
Help > About menu in the user interface.
You will find the full list of addresses and phone numbers of local offices either at the end
of this user manual (for manuals on hardware products) or at the following page on the
EVS website: http://www.evs.com/contacts.
User Manuals on EVS Website
The latest version of the user manual, if any, and other user manuals on EVS products
can be found on the EVS download center, on the following webpage:
http://www.evs.com/downloadcenter.
I
INSTALLATION MANUAL Epsio Zoom 1.1
Table of Contents
TABLE OF CONTENTS
III
1.
1
INTRODUCTION
1.1. Product Overview
1
1.2. Technical Requirements
1
2.
SETUP
3
2.1. Setup Overview
3
2.2. Setup Cabling
4
3.
6
CONFIGURATION
3.1. Configuring Multicam
Table of Contents
6
III
INSTALLATION MANUAL Epsio Zoom 1.1
1.
Introduction
1.1.
Product Overview
Description
Epsio Zoom for 4K zooming allows operators to scale any 16:9 region within a 4K frame to
HD, in real time.
An operator identifies the 4K content, either via a touchscreen or a mouse, and then
selects the specific part of the high-resolution image for zooming. The resulting zoom
sequence can be used for the HD live diffusion as a regular instant replay.
Functional Worfklow
In Epsio Zoom, the operators define a virtual camera on the region where they want to
zoom on the video. They also define the zoom depth, and other parameters. Cue points
can be automatically associated to timecodes the zoom points are defined on. The zoom
timecode and parameters are stored in a virtual camera register.
On the LSM Remote Panel, the operators take control over the Epsio Zoom by activating
the Epsio Zoom mode. In this mode, the operators can replay the video sequence, and
easily control the Epsio Zoom from the LSM Remote Panel.
The zoom sequence can be played out in real time in HD.
1.2.
Technical Requirements
EVS Server
Hardware
XT3 server ready for 4K, with the latest hardware configuration:
•
HS-873 with 256MB of RAM
•
V3X modules with serial number 1300 or higher
•
HDD with revision 10K.5 or higher
•
RAID configuration in 5+1 (no spare)
Software
Multicam version 12.05 or higher
The software option for UHDTV-4K (license code 27) is required.
1. Introduction
1
EVS Broadcast Equipment SA
Issue 1.1.A - April 2014
Epsio Zoom
Hardware
Epsio PC (3 RU)
AJA Corvid Ultra (2 RU)
Touchscreen (optional)
Software
Epsio Zoom version 1.1.3 or higher
2
1. Introduction
INSTALLATION MANUAL Epsio Zoom 1.1
2.
Setup
2.1.
Setup Overview
The following drawing presents a typical setup with Epsio Zoom:
•
The 4K cameras are connected to the XT3 server configured in a 4K format.
•
The content is sent from the XT3 server to the AJA Corvid Ultra in a 4K format.
•
The AJA Corvid Ultra outputs an HD signal.
•
The Corvid Ultra is connected to the Epsio PC via a dedicated PCIe link.
Refer to the Technical Hardware manual for more information about the PCIe link.
•
2. Setup
The Epsio Zoom application, installed on the Epsio PC, communicates with the PC
LAN port of Multicam. This means that they both must be connected to the same
network subset.
3
EVS Broadcast Equipment SA
2.2.
Issue 1.1.A - April 2014
Setup Cabling
Introduction
The following abbreviations and color codes are used in drawings:
Item
Meaning
Item
Meaning
TL
top left quadrant
Player output
TR
top right quadrant
Recorder input
BL
bottom left quadrant
BR
bottom right quadrant
Cabling Schema
The following schema presents how an XT3 6U server running a 1 REC + 1 PLAY 4K
configuration should be cabled to the AJA Corvid Ultra:
4
2. Setup
INSTALLATION MANUAL Epsio Zoom 1.1
EVS Server Cabling Options
You can have the following codec configurations on an XT3 6U server running in 4K:
1 IN + 1 OUT
2 IN + 1 OUT
1 IN + 2 OUT
2. Setup
5
EVS Broadcast Equipment SA
3.
Configuration
3.1.
Configuring Multicam
Issue 1.1.A - April 2014
Server Tab
The following parameters should be configured as follows in the Server tab:
•
Resolution: UHDTV-4K
•
Codec: Avid DNxHD
•
Bitrate:
◦
260Mbps with 2 channels (1REC+1PLAY)
◦
200Mbps with 3 channels (2REC+1PLAY or 1REC+2PLAY)
Channels Tab
The following parameters should be configured as follows in the Channels tab:
•
Base config: Multicam LSM
•
3G/Dual: Level-A or Level-B
Monitoring Tab
The following parameter should be configured as follows in the Monitoring tab:
•
Layout : 1
Operation Tab
The following parameters should be configured as follows in the Operation tab:
•
Epsio: Zoom
◦
6
IP address <IP address of Epsio Zoom>
3. Configuration
Corporate
+32 4 361 7000
North & Latin America
+1 973 575 7811
EVS Headquarters
Liège Science Park
16, rue Bois St Jean
B-4102 Seraing
Belgium
To learn more about EVS go to www.evs.com
Asia & Pacific
+852 2914 2501
Other regional offices
www.evs.com/contact
EVS Broadcast Equipment is continuously adapting and improving its products in accordance with the ever changing
requirements of the Broadcast Industry.
The data contained herein is therefore subject to change without prior notice. Companies and product names are
trademarks or registered trademarks of their respective companies.