1. technology and computing
2. electronic components

The Avermetrics™ Test and Measurement System
has been engineered from the ground up for production line testing of electronic products, subassemblies,
boards, and components. It was designed by an engineering team with extensive product development and
testing experience, with performance and the total cost
of testing as clear design criteria.
mands via Telnet. The XOS operating system interprets
these commands, routes them to the proper module
or modules, collects the results, and sends them back
to the host computer in an easy-to-parse XML format.
Literally any programming language and operating
system that can open a networking socket will support
XOS and this system.
This system, and the currently available range of plugin modules, offers a wide range of test capabilities,
from professional, semi-professional, and consumer
audio product testing, to basic board level tests, to process control, and more. New modules to add new tests
are being added to the library every day.
Software Support
Modular System
This is a modular system using a custom 1U rack
designed to hold up to 4 modules. The system is highly
scalable: Racks may be interconnected using the
AVERLINK™ connectors on the back of each rack unit;
up to 64 rack units holding up to 254 modules can be
connected in a single system. Internally, each module
has an array of processors, and the system is organized
as a large, interconnected two-dimensional array of
these processors in a distributed intelligence configuration. Because each module is intelligent it does its
own analysis, so tests across multiple modules occur in
parallel, significantly reducing testing time.
Communication
XOS™ is an XML-based operating system that is at
the core of the test system. To define tests or do other
operations, a host computer sends simple XML com-
Avermetrics supplies documentation, C++ classes that
handle all aspects of communication with the system
and parsing of XML commands and results, and example applications (with complete source code) to get you
started. One of those example applications, AverTest,
provides full-featured test execution using simple XML
test and limit definition files so you can start testing on
the production line right away.
Future Proof
The system supports a complete Device Firmware Update capability so new features and updated firmware
can be programmed into existing systems in the field,
with no downtime. Adding new tests and more channels is as simple as plugging new modules and racks
into an existing system. Your investment in testing
never goes obsolete.
Modules
Currently, there are six different modules available to
test audio and analog signals, and to control process
operation and interact with external sensors and digital signals. More information and pricing for each of
these modules is below.
1116 Colorado Blvd., Los Angeles, CA 90041
T: (323) 230-0515 | F: (323) 704-3316
[email protected] | www.avermetrics.com
Rev. B
P/N 770-00004
9140 1U Rack Unit
4021 Analog Audio Input Module
Every system has at least one 9140 Rack unit. Up to 64
rack units may be interconnected to create large, unified test systems for multi-channel audio and diverse
testing requirements. Each rack accepts four modules.
Any number of 4021 Input modules may be installed
in a given system. This module provides two high-performance audio inputs, supporting tests over the entire
audio spectrum and a wide range of signal levels. Each
channel operates simultaneously and independently,
doubling effective throughput compared to conventional audio test systems. Multiple modules in a system all operate in parallel, greatly reducing test time
for multi-channel measurements when compared to
switched, repetitive testing.
Two AVERLINK ports (A and B) are supplied on the
back panel. Interconnect racks by connecting A to
B or B to A using the supplied Cat5 cables. (See the
Hardware Installation manual for more information on
interconnections between racks.)
Dimensions (w/o Rack Ears, no 440mm x 242mm x 44.45mm
modules)
(17.3in x 9.5in x 1.75in)
Weight (no modules)
3.86 kg (8.5 lbs)
Input
90Vrms to 240Vrms, 47 to
63Hz, Single Phase
Input Power (maximum)
100W
Cost
9140 Rack Unit$750
US NEMA 5-15P Power Cord
N/C
UK BS1363 UK3 Power Cord
N/C
3001 Ethernet Host Adapter
Every system has one (and only one) Ethernet Host
Adapter module. This module provides communication between the system and host computer, and performs test scheduling and results formatting tasks during test execution. Communication with the module is
done via Telnet, and an embedded web server provides
access to configuration settings and status information.
A white front panel LED indicates system activity and
status.
Signal inputs are via balanced XLR connectors. Singleended signals are supported by grounding the cold input (pin 3) to ground (pin 1) and driving the hot input
(pin 2) relative to ground. Ground lift is also selectable
for completely floating balanced inputs.
Currently available native tests are: FFT (32 to 65536
points), Level, DR, SNR, THD+N.
Dimensions (maximum)
170mm x 107mm x 44.45mm
(6.7in x 4.2in x 1.75in)
Weight
348 g (12.3 oz.)
Input Level, maximum
+32 dBu
Autorange (in 6dB steps)
10 ranges, +32 dBu to -22
dBu full scale.
THD+N, +32 dBu to 0 dBu, @
1 kHz, typical
-114 dB
THD+N, -1 dBu to -28 dBu, @
1 kHz, typical
-110 dB
THD+N, 10 Hz to 22 kHz @
+26 dBu, minimum
-108 dB
Dynamic Range, @ 1 kHz,
autorange enabled, minimum
145 dB
Dimensions (maximum)
170mm x 107mm x 44.45mm
(6.7in x 4.2in x 1.75in)
Signal to Noise, @ 1 kHz, autorange enabled, minimum
145 dB
Weight
156 g (5.5 oz.)
126 dB
Ethernet Support
100Base-T via RJ-45, AutoIP,
mDNS, Auto MDIX, DHCP,
Static IP
Dynamic Range, @ 1kHz, autorange disabled, typical
Signal to Noise, @ 1 kHz, autorange disabled, typical
126 dB
Front Panel LEDs
White, system activity; Green,
link on, Yellow, blink on link
activity.
Default mDNS Address
xos.local
Cost
3001 Ethernet Host Adapter
$750
Frequency range, rated perfor- 10 Hz to 22 kHz
mance
Level accuracy and flatness,
integration >= 1000
+/- 0.02dB
Cost
4021 Analog Audio Input Module
$2500
4121 Analog Audio Generator Module
9001 Filler Module
Any number of 4121 Generator modules may be
installed in a given system. This module provides two
high-performance audio outputs, providing audio
stimulus signals over the entire audio spectrum and at
a wide range of signal levels. Each output may be set to
different frequencies and/or levels. Three very low distortion oscillators are available for generating complex
stimulus signals and may be assigned in any combination to either or both outputs.
Rack units require that all four slots be filled with
modules to ensure proper internal communication and
signal integrity. For rack units with fewer than four
modules to meet this requirement each unused slot
is filled with a filler module, which provides needed
signal routing and termination.
Dimensions (maximum)
170mm x 107mm x 44.45mm
(6.7in x 4.2in x 1.75in)
Weight
226 g (8 oz.)
Output Level, maximum
+26 dBu
Autorange (in 6dB steps)
9 ranges, +26 dBu to -22 dBu
full scale.
THD+N, +26 dBu to 0 dBu, @
1 kHz, typical
-108 dB
THD+N, -1 dBu to -28 dBu, @
1 kHz, typical
-104 dB
THD+N, 10 Hz to 22 kHz @
+26 dBu, minimum
-104 dB
Dynamic Range, @ 1 kHz,
autorange enabled, minimum
145 dB
Signal to Noise, @ 1 kHz, autorange enabled, minimum
145 dB
Dynamic Range, @ 1kHz, autorange disabled, typical
128 dB
Signal to Noise, @ 1 kHz, autorange disabled, typical
128 dB
+/- 0.02dB
Output Impedance, nominal
10Ω
Relay, rated life
109 cycles
Cost
4121 Analog Audio Generator Module
Options
001 Enhanced THD+N (-110dB, typical)
014 Output Impedance 40Ω
015 Output Impedance 150Ω
016 Output Impedance 600Ω
$100
3101 Isolated I/O Module
This module provides eight opto-isolated inputs and
eight reed relay SPST outputs. Because the inputs and
outputs are all completely isolated from the system
ground and internal signals, this module is perfect for
controlling processes in noisy environments or adjusting sensitive analog signals internal to test devices.
The eight opto-isolated inputs can be used to sense the
state of external signals, such as proximity switches,
out of limit sensors (overtemp, overvoltage, etc.),
switch closures, test status, and other binary events.
Similarly, the eight reed relay outputs can be used to
close circuits during board-level tests, actuate motors,
valves, or other process control components, light annunciators, etc. These are very high reliability relays;
they are rated at 109 cycles at low signal levels, and can
handle up to 10W.
Frequency range, rated perfor- 10 Hz to 22 kHz
mance
Level accuracy and flatness
Cost
9001 Filler Module$125
Supplied with a factory-provisioned system N/C
Eight Green LEDs indicate the state of the opto-isolated input signals, while eight Red LEDs indicate the
state of the reed relay outputs for easy visual feedback.
$1500
Add $500
Add $100
Add $100
Add
Dimensions (maximum)
170mm x 107mm x 44.45mm
(6.7in x 4.2in x 1.75in)
Weight
246 g (8.7 oz.)
Actuation current, opto-isolated inputs, minimum
4ma
Opto-isolator input, forward
voltage, typical
1.3V
Opto-isolator input, reverse
voltage, maximum
100V
Relay, rated life
109 cycles, 1V@10ma
Relay, maximum open voltage
200V
Relay, maximum closed current
0.5A
Relay, static resistance
0.2Ω
Insulation Breakdown Voltage,
minimum
500V
Dimensions (maximum)
170mm x 107mm x 44.45mm
(6.7in x 4.2in x 1.75in)
Input connector
DB-25 Female D-Sub
Weight
242 g (8.5 oz.)
Output connector
DB-25 Male D-Sub
Actuation current, opto-isolated inputs, minimum
4ma
Opto-isolator input, forward
voltage, typical
1.3V
Opto-isolator input, reverse
voltage, maximum
100V
Insulation Breakdown Voltage,
input, minimum
500V
Input connector
DB-25 Female D-Sub
Parallel Output connector
DB-44 Male D-Sub
SPI Port connector
DE-9 Male D-Sub
SPI Data Rate, maximum
1 Mbps
Output source current, minimum, per output
+/- 12ma
Cost
3101 Isolated I/O Module
$750
3102 Digital I/O Module
The 3102 Digital I/O Module is identical to the 3101
module, with the addition of a fully isolated power
supply. This supply can provide power for small external sensors and other test-fixture circuits, and in some
situations may simplify external connections to the
system.
This isolated power supply provides up to 100ma of
current across any of the available 12V, 5V, and 3.3V
outputs. All outputs are short-circuit protected and
current limited. Power is available on both the input
and output connectors.
Cost
3102 Isolated I/O Module
$900
3103 Digital I/O Module
This module provides eight opto-isolated inputs and 32
digital voltage level outputs, along with a dual bidirectional SPI control port. This module is ideal for control
of external test sets, test devices, and manufacturing
processes.
The opto-isolated inputs are identical to those on the
3102 Isolated I/O module. No power is supplied by this
module to drive external circuitry, other than what is
available directly from the digital outputs.
The outputs are selectable (in 8-bit banks) between
3.3V and 5V logic levels. These are high-current outputs and can source or sink up to 12ma each.
The SPI connector has MISO, MOSI, SCK, and two
CS signals and can support two bidirectional SPI ports
for control and initialization of test devices and/or test
sets. These signals are independent of the 32 digital I/O
outputs and opto-isolated inputs.
Cost
3103 Digital I/O Module
$750
6020 Slew Rate Measurement Module
This module performs direct slew-rate measurements
of digital and analog test devices. Its two pairs of inputs
and outputs are fully differential and independent, and
can be used in either differential mode or single-ended
mode, depending on requirements.
When not actively measuring slew rate, this module
passes through all input and output signals to a second
set of outputs and inputs. These can be used to interconnect a 6020 module with a 4021 Input module and
4121 Generator module so that only a single connection to a test device is required to make both analog
audio and slew rate measurements. These signals are
passed through using reed relays, so all connections
are completely galvanic, with no active devices in the
signal path when the 6020 module is not active.
Slew rate is measured by driving the outputs between
any two programmable voltages and measuring the
elapsed time between two programmable threshold
voltages on the inputs. This scheme accommodates
devices exhibiting gain or loss, over a wide range of
possible input and output voltages.
Dimensions (maximum)
170mm x 107mm x 44.45mm
(6.7in x 4.2in x 1.75in)
Weight
246 g (8.7 oz.)
Output voltage range, each
leg
+/- 12V
Input voltage range, each leg
+/- 12V
Output voltage resolution
4096 steps, 5.86mV
Input threshold resolution
4096 steps, 5.86mV
Generator output slew rate,
minimum
750V/uS
Input slew rate, minimum
750V/uS
Output impedance, maximum
10Ω
Input impedance, nominal
10MΩ || 20pF
Time resolution
8nS
Cost
6020 Slew Rate Measurement Module
Interconnect Cable Set (XLR to DE-9)
$900
$100
About Avermetrics
Founded in 2010, Avermetrics develops, manufactures,
and markets a complete line of Test and Measurement
systems, all with a focus on testing in production environments. Speed, accuracy, and data combine to make
your production tests effective as possible.
Our engineering staff is one of the best around, with
decades of experience developing military radar and
simulation systems, RF and microwave products,
pro-audio, MI and consumer mid- and high-volume
products, medical and scientific instrumentation, factory process control systems, and more. While managing volume production in the US and Asia, we have
learned best practices for testing and verification on
production lines.
Now we have taken all of that experience and produced the only Test and Measurement system available
that is tailor made for you and your production test
requirements.
Notes
• All specifications, features, and prices are subject to
change without notice.
• Prices shown are is $US, and are Ex-Works, Los
Angeles, California USA.
• Documentation, software, source code, and example applications are provided solely to support the
use of Avermetrics’ products and may not be used
for any other purpose without the express written