Download Report

CONV2-E version 3
Protocol converter from Pelco-D to Bosch Bi-phase
MANUAL INSTRUCTION
The converter is a microprocessor device, designed to control PTZ cameras Enviro Dome by uses
keyboards (or DVRs), working in Pelco-D protocol. This allows for integration of Bosch company
cameras with any other camera system or digital recorders. The converter receives commands in Pelco-D
protocol by uses RS-485 interface and after translation the data by appropriate software, the commands
are sending by Bi-Phase output.
1. Structure of connections
The converter is connected between keyboard and PTZ cameras and it requires 9~24V D or AC supply.
9~24V AC/DC
Keyboard
Klawiatura
(Pelco-D)
Bosch camera
G3 / G4
Kamera
Bosch
CONV2-E
(Pelco-D)
G3 / G4
RS485
Bosch Biphase
Connection diagrams of CONV-2E converter
2. Description of connection terminals
1
10
LED1 – signal transmission of Bi-Phase
LED2 – signal transmission of Pelco-D
10
9~24V
Zasilanie
Zasilanie
Term1
RS485 - A +
Klawiatura
GND
RS485 - B Term2
Biphase +
GND
Biphase -
1
Ewimar Sp. z o.o.
www.ewimar.pl
Power supply: It used to connection 9~24V DC / AC supply
RS-485 A/B: RS-485 interface, designed to connection keyboard
Term1: 120Ω terminating resistor for RS-485 interface
Biphase +/ -: Bi-Phase interface, designed to connection cameras
Term2: 120Ω terminating resistor for Bi-Phase interface
GND: Clamps of power ground (cable shield)
RS-485 interace, should be connected always in accordance with other
devices
A to A and B to B.
Biphase interface, should be connected accordingly do clamps C+ i Cin Bosch.
CONV3-A/B rev 1.0
A
B
R
R
C+ CConnection
Połączenia
ofwewnątrz
inside
For longer cables of bus, both RS-485 interface and
Biphase, should be included to terminating resistor. This
will prevent wave reflections in cables, which are cause of
transmission errors. Terminating resistors should be
connected only in devices, which are of ends of the bus.
Larger number of resistors will cause an excessive burden
of transmission.
Zwory
Jumpers
Switching resistors in converter consists in the combination
wire clamp TERM1 with A+ and TERM2 with Biphase+,
respectively for RS-485 and Bi-phase interfaces.
3. Description of switches
OFF
(up)
ON
(down)
Description of switches:
Transmission speed
2400baud
4800baud
9600baud
19200baud
RS-485
DIP 1
OFF
ON
OFF
ON
DIP 2
OFF
OFF
ON
ON
Transmission speed is is defined only for RS-485 interface, transmission speed for Bi-phase isn’t changeable.
Input protocol
Pelco-D (work as CONV-2E)
Pelco-P (work as CONV-2G)
DIP 3
OFF
ON
Switch of No. 3 is used to select input protocol, means changing our model of converter (CONV2-E or CON2-G)
Decreasing of address
Excluded
Attached
DIP 4
OFF
ON
Function of decreasing of address is recommended in working mode as CONV-2E, because in Pelco-D protocol address of
cameras start at number 1, while in Bi-phase protocol natomiast w protokole Bi-phase address of cameras start at number 0.
Because in pelco-P protocol address start at numer 0, switch should be attached for working mode of CONV-2G.
4. Start-up
All connections and configuration of switches, should be made with disconnect the power supply of
converter. Should pay attention to correct polarity of RS-485 and Bi-Phase interfaces.
Correct working of converter can be determined by LED observing. If device is correct configured and
connected, at the time of trying to control from desktop, both LEDs should blink.
Ewimar Sp. z o.o.
www.ewimar.pl
CONV3-A/B rev 1.0
5. List of translated commands
Nr
Function of Pelco-D
Function of Bosch cameras
1
Joystick: UP, DOWN, LEFT, RIGHT,
ZOOM, FOCUS, IRIS
Start Auto-Pan
Start Auto-Scan (limit)
Set left limit scan
Set right limit scan
Call preset 100
Call preset 101
Call preset 124
Call other preset (1~99)
Start learn pattern
Stop learn pattern
Run pattern
Set preset 115
Call preset 115
Call preset 102
Start learn pattern
Set preset 116
Set preset 122
Set other preset (not described in this
table)
Set preset 118
Call preset 103
Joystick: UP, DOWN, LEFT, RIGHT,
ZOOM, FOCUS, IRIS
Start Auto-Pan
Start Auto-Scan
Set left limit scan
Set right limit scan
Run tour
Run Auto-Tracking
Home position, motor calibration
Call scene 1~99
Start learn pattern A
Stop learn pattern A
Run pattern A - continuous
Start learn pattern B
Stop learn pattern B
Run pattern B - continuous
Start learn pattern A
Edit scene name
Edit auto-pan / scan speed
Entry do advance scene edit
ON 1 ENTER
ON 2 ENTER
SET 101 ENTER
SET 102 ENTER
ON 8 ENTER
ON 78 ENTER
SET 110 ENTER
SHOT 1~99
ON 100 ENTER
OFF 100 ENTER
ON 50 ENTER
ON 101 ENTER
OFF 101 ENTER
ON 52 ENTER
ON 100 ENTER
ON 62 ENTER
ON 14 ENTER
SET 100 ENTER
Tour Edit
Clear alarm
SET 900 EDIT
OFF 65 ENTER
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Equivalent of
command for
Bosch
keyboard
Locked functions
21 Set preset 127
Unlock advanced functions
OFF 90 ENTER
22 Call preset 127
Lock advanced functions
ON 90 ENTER
23 Call preset 95
Entry to main menu*
ON 45 ENTER
24 Call preset 126
Display fast address*
ON 997 ENTER
25 Set preset 123
Hide OSD screen*
OFF 60 ENTER
26 Call preset 123
Display OSD screen*
ON 60 ENTER
27 Set preset 119
Edit park function*
ON 9 ENTER
28 Set preset 120
Entry to password menu*
SET 802 ENTER
29 Set preset 121
Edit tour time*
ON 15 ENTER
*) This functions are available before unlocked Advanced Functions – more information you can find on
instruction of Bosch cameras.
Because cameras, which use Pelco-D protocol have a less function than Bosch keyboards, the
converter doesn’t translate commands of Fast addressing. To use this function is recommended
uses original Bosch keyboard or hardware addressing.
Producer: Ewimar Sp. z o.o., ul. Konaskiego 84, 01-355 Warsaw, Poland,
Phone: +48 (22) 6919065, email: [email protected], www.ewimar.pl
Ewimar Sp. z o.o.
www.ewimar.pl
CONV3-A/B rev 1.0