Jungheinrich
Electric Reach Truck Retrak
Capacity 1600 kg
®
ETM 216/ETV 216
Driver position with
MULTI-PILOT
AC or DC optional
Electrical steering –
extremely light, energy
saving
Energy reclamation during
braking and lowering
Jungheinrich Retrak reach trucks are used
wherever space conditions are particularly confined and where heavy loads are to be raised to
high lift heights. The Jungheinrich Retrak, apart
from its excellent performance, is also very
economical.
Driver’s Compartment: The driver’s compartment, through generous dimensioning, ensures
a comfortable body positure and ergonomic
back support. Excellent all round visibility and
low noise levels.
Seat: The combined backrest/seat area adjustment provides improved visibility of the load at
great lift heights. Hydraulic cushioning reduces
stress from jolts and vibrations.
Pedals: Automotive type arrangement.
Instruments: Display and setting instrument
LISA (LC information and service display) for
warning displays, for setting important driving
and lifting parameters and for the storage of
service information. Operating hour meter and
battery discharge monitor fitted as standard.
Steering: Fully electrical steering with steering
wheel diameter of 200 mm ensures optimum
ease of operation. Each steering wheel movement
leads to a defined drive wheel position.
Hydraulic Lever SOLO-PILOT: A single lever
for lifting, lowering, reach, tilting and sideshifting
permits particularly fast stacking and retrieval
ISO-9001, ISO-14001 Certification of Quality and
Environment Management.
without hand changes. Double operation also
possible during lifting. The direction of travel is
also controlled with this lever.
2. Foot operated hydraulic drive and load wheel
brake
3. Parking brake
Drive: 5.4 kW (1 hour rating) shunt wound
motor with high overload capacity. Optional AC
asynchronous motor with 6.0 kW (1 hour rating)
capacity. 2 years warranty on both motors.
Hydraulics: Powerful series wound motor with
11.5 kW (15 % rating) capacity and low noise
internally geared pump. Optional AC asynchronous motor with 12 kW (15 % rating) capacity.
Electric proportional technology permits quiet
and sensitive operation of the hydraulic functions.
Multiple operation during lifting and lowering
cuts stacking and retrieval time.
Battery: 48 Volt (DIN 43 531-B) 360/420,
480/560 and 600/700 Ah (750 Ah high power).
While the battery is unlocked, travel is only
possible at reduced speed for safety reasons.
Drive and Hydraulic control: DC travel and
hydraulic control as standard. AC control
optional. Power transistors control the motors
with high pulse frequencies in an energy saving
and noiseless manner. The drive control permits
jerk-free starting and strong acceleration. Adjustable energy feedback on releasing the drive
pedal through regenerative braking. In addition,
crawl speed may be selected. Energy reclamation
during lowering of the forks extends the battery
operating time (optional).
Wheels: Drive wheel dia. 343 x 114 mm, load
wheels dia. 285 x 100 mm. Drive wheel and load
wheels with Vulkollan tyres.
Brake: Three independent braking systems
fitted as standard:
1. Regenerative braking through releasing the
drive pedal or reversal of travel direction
Panorama Mast: The mast provides excellent
visibility of the forks, load and reach legs. Cold
drawn sections from 7100 mm lift height onwards
have high surface strength and permit high
capacities. Two-stage and three-stage masts are
available. Standard lift heights up to 10,250 mm.
The patented mast reach cushioning (on ETV only)
at great lift heights permits fast stacking and
retrieval. Mast tilt is standard. Fork tilt optional
from 6200 mm.
Easy Servicing: Drive and electronics cover can
be opened quickly and easily for servicing and
maintenance work. Carbon brush wear display
is standard. Easy servicing through LISA as fault
messages are being saved.
Optional Extras: Integral sideshift, height display,
cold store design, battery charging systems,
double pedal for drive function.
Safety: The trucks conform to the EU Guidelines
C for fork lift trucks.
ETM 216/ETV 216
Performance Data
Capacity
Travel speed
without load (DC/AC)
with load (DC/AC)
Lifting speed
without load (DC/AC)
with load (DC/AC)
Lowering speed
without load
with load
Max. gradient performance without load
with load
Service weight (ETM/ETV)
with h3 = 5300 mm and 420 Ah battery
Battery variants (DIN 43531-B)
kg =
km/h =
km/h =
m/s =
m/s =
m/s =
m/s =
%=
%=
1600
10.6/11.8
10.3/11.8
0.55/0.64*
0.35/0.35
0.50
0.50
15
10
kg = 3000/3040
Ah = 360/420
480/560
600/700
DC = Direct Current/AC = Alternating Current
* max. speed with higher energy requirement
Technical Data
Q — Capacity
c
— Load centre
I2
— Length incl. fork upright (ZT/DZ)
I4
— Reach (ZT/DZ)
I7
— Length over reach legs
b1 — Max. width (ETM/ETV)
b2 — Width at driver’s side (ETM/ETV)
b3 — Fork carrier width (top/bottom)
b4 — Width between reach legs (ETM/ETV)
b5 — Width across forks, max.ETM/ETV)
b11 — Track width (ETM/ETV)
h6 — Height overhead load guard
h7 — Seat height
h8 — Height reach legs (with load wheel cover)
Wa — Turning radius (ETM/ETV)
s/e — Fork thickness/width
I
— Standard fork length
x
— Load distance (ZT/DZ)
y
— Wheelbase
m2 — Ground clearance centre wheelbase
a
— Safety clearance
— Forward mast tilt/fork tilt
— Backward mast tilt/fork tilt
h1 — Closed mast height
h2 — Free lift
h3 — Lift
h4 — Extended mast height
Ast — Working aisle width
kg = 1600
mm = 600
= 1167*/1190 *
= 666*/644 *
= 1802
= 1120/1238
= 1106/1186
= 800/680
= 782/900
= 717
= 986/1104
= 2190 (2085)
= 995
= 300
= 1663/1675
= 40/120
= 800/950/1150
= 462*/440 *
= 1420
= 95
= 200
see individual tables
* Dimensions are given for 420 Ah, different values for other battery capacities.
Load Centre “C” in mm
400
500
600
700
800
900
1000
Capacity in kg
1700
1600
1500
1400
1300
1200
1100
1000
Working Aisle Widths (mm)
Pallet Size
Position
Ast/Ast3* incl. 200 mm safety clearance
with battery
360/420 Ah 480/560 Ah 600/700 Ah
800 x 1200 mm crosswise
2235/2575 2325/2625 2415/2682
lengthways 2635/2734 2725/2814 2815/2897
1000 x 1200 mm crosswise
2435/2696 2525/2760 2615/2828
lengthways 2635/2785 2725/2861 2815/2940
*Ast = Wa-x+l+a/Ast3 acc. to VDI 2198 (diagonal method).
With ZT –20 mm, with lift height 7100 mm +30 mm, with fork tilt +95mm.
Changes and technical improvements reserved.
Jungheinrich (G.B.) Ltd.
Head Office:
Southmoor Road · Wythenshawe
Manchester M23 9DU
Telephone 0161-946 6600
Telefax
0161-946 0195
www.jungheinrich.co.uk
Standard Mast Designs*
Two-stage Masts ZT
h1
h3
h2
mm
mm
mm
1950
2900
80
2050
3100
80
2200
3400
80
2300
3600
80
2400
3800
80
2500
4000
80
2700
4400
80
h4
mm
3544
3744
4044
4244
4444
4644
5044
MN
°/°
2/5
2/5
2/5
2/5
1/5
1/5
1/5
GN
°/°
–
–
–
–
–
–
–
Three-stage Masts DZ
h1
h3
mm
mm
1950
4250
2200
5000
2300
5300
2400
5600
2500
5900
2600
6200
2700
6500
2900
7100
3100
7700
3200
8000
3300
8300
3440
8720
3540
9020
3670
9410
3840
9920
3950
10250
h4
mm
4894
5644
5944
6244
6544
6844
7144
7744
8344
8644
8944
9364
9664
10054
10564
10894
MN
°/°
1/5
1/5
1/5
1/3
1/3
1/3
0,5/2
0,5/2
0,5/1
0,5/1
0,5/1
0,5/1
0,5/1
–
–
–
GN
°/°
–
–
–
–
–
2/5
2/5
2/5
2/5
2/5
2/5
2/5
2/5
2/5
2/5
2/5
* other mast designs on request
MN = Mast tilt, GN = Fork tilt
h2
mm
1306
1556
1656
1756
1856
1956
2056
2256
2456
2556
2656
2796
2896
3026
3196
3306