MediaPort 7000 Series Quick Reference Guide MediaPort Chassis (MPC-7002) Bezel Air Vents Power Indicator NOTE: Alarms will cause the display to flash. To stop flashing, resolve the alarm or touch the display. The Port Status Display allows you to enable the display of a static color bar pattern on any or all of the SDI Output connectors, which can be used to verify connectivity. For more details, refer to “MediaPort 7000 Series Front Panel” in the Spectrum Installation and Hardware Reference Guide. Status of Module A Status of Module B Port Status Display Port Status Display Health Summary Reference Input Channel 0: Player name, Player state, and mecode Channel 1: Player name, Player state, and mecode Environmental alarms, if any Health Summary Reference Input Channel 0: Player name, Player state, and mecode Channel 1: Player name, Player state, and mecode Environmental alarms, if any MediaPort Chassis Rear Panel Power Supplies and LEDs PS 0 PS 1 Module A Filler Panels Module B Power Supply LED States Off: No AC power to both units Green (blink): AC power present, unit on standby Green (solid): Power supply on and OK Red (blink): No AC power to this unit only Red (solid): Power supply failure NOTE: When a power supply fails, an audible alarm sounds. GPIO/RS-422 Signal Assignments The MediaPort 7000 module has a female GPIO/RS-422 connector that can be connected to an external device and used to control players. For information on configuring GPIO/RS-422 using SystemManager, refer to “MediaPort Configuration” in the Omneon SystemManager User Guide. 9 8 7 6 5 4 3 2 1 18 17 16 15 14 13 12 11 10 26 25 24 23 22 21 20 19 GPIO/RS-422 Signals Function RX (-/+) TX (-/+) Function Pin Ground GPIO 0 GPIO 1 GPIO 2 GPIO 3 GPIO 4 GPIO 5 GPIO 6 GPIO 7 18 19 20 21 22 23 24 25 26 Serial 1 2-3 10-11 Serial 2 4-5 12-13 Serial 3 6-7 14-15 Serial 4 Ground 8-9 16-17 1 Harmonic Technical Support: +888 673 4896 (Americas), +65 6542 0050 (Asia Pacific), + 44 1252 555 450 (EMEA), +7 495 926 4608 (Russia, CIS), +81 3 5565 6737 (Japan), +86 10 8391 3313 (China, mainland) 28-0339 Rev. D MediaPort Modules 7000 Series Rear Panel Unused 13 1 2 3 4 6 5 15 RS-422 Port LEDs 14 Activity Activity Ethernet Port LEDs Activity 7 1. 2. 3. 4. 5. 6. 8 10 9 11 16 17 12 HD/SD SDI IN Channel A HD/SD SDI OUT Channel A (Primary) HD/SD SDI OUT Channel A (Secondary) HD/SD SDI IN Channel B HD/SD SDI OUT Channel B (Primary) HD/SD SDI OUT Channel B (Secondary) 7. 8. 9. 10. 11. 12. Status 18 LTC IN Channel A LTC OUT Channel A LTC IN Channel B LTC OUT Channel B Reference IN Reference Loop 13. 14. 15. 16. 17. 18. Soft Power button (middle) Status/Wink LED (bottom) GPIO/RS-422 connector RS-422 Port Service Use Only Ethernet/MediaDirector Installing a MediaPort Module To install a MediaPort module: 1. If you are installing two modules, you ma need to first remove a filler panel from the chassis. From the rear of the MediaPort, unscrew the two lock screws that secure the filler panel, and then remove the filler panel. Caution: Do not use the two lock screws on the rear panel of the module to pull it into position. Tighten the screws only after the module is fully inserted. 2 1 3 2. Grasp the module handle and push firmly into the slot. Ensure the module is fully inserted by pressing on the connectors with the palm of your hand. 4. If installing two modules, repeat steps 1-3 for the second module. 3. Tighten the two lock screws on the rear of the module to secure it to the chassis. For complete replacement instructions, refer to the Spectrum Component Replacement Guide. Harmonic Technical Support: +888 673 4896 (Americas), +65 6542 0050 (Asia Pacific), + 44 1252 555 450 (EMEA), +7 495 926 4608 (Russia, CIS), +81 3 5565 6737 (Japan), +86 10 8391 3313 (China, mainland) 28-0339 Rev. D Replacing a MediaPort Chassis Power Supply To remove a power supply: 1. Disconnect the AC power cable. 2. Press the release lever to the right and pull the handle to remove the power supply. To install a new power supply: 1. Grasp the module handle and push firmly into the slot. 2. Connect the AC power cable. For complete replacement instructions, refer to the Spectrum Component Replacement Guide. Removing and Replacing a MediaPort Chassis Front Bezel 1 2 For complete replacement instructions, refer to the Spectrum Component Replacement Guide. To remove the bezel: 1. Remove the center screws on each side of the chassis that secure the bezel to the chassis. . Note: Keep the rack ear in place. 2. Unplug the bezel power/data connector. 3. Pull the bezel away from the chassis. To install the new bezel: 1. Attach the bezel power/data connector. 2. Align the bezel in front of the chassis so that the Omneon logo appears in the top-left corner, and the metal corners of the bezel are level with the rack ears of the chassis. 3. Press the bezel straight onto the chassis. 4. Attach the two center screws on each side of the chassis to secure the bezel to the chassis. Harmonic Technical Support: +888 673 4896 (Americas), +65 6542 0050 (Asia Pacific), + 44 1252 555 450 (EMEA), +7 495 926 4608 (Russia, CIS), +81 3 5565 6737 (Japan), +86 10 8391 3313 (China, mainland) 28-0339 Rev. D License Options for MediaPort 7000 Series Modules The following table shows available MediaPort options. Note the following additional licences not shown in the table: • MIP-7XXX-XXX-VC3P provides playout of VC-3, in addition to the other functionality indicated by the product ID. • MIP-7XXX-XXX-VC3R provides record of VC-3, in addition to the other functionality indicated by the product ID. For more details on the MediaPort 7000 Module, refer to “MediaPort 7000 Series Reference” in the Spectrum Installation and Hardware Reference Guide. Product ID SD MIP-7100-DVS MIP-7100-M2S MIP-7100-DMS MIP-7300-DMS MIP-7100-DVH MIP-7100-M2H MIP-7100-DMH MIP-7101-DMH MIP-7600-UVP MIP-7600-APR MIP-7601-APR MIP-7300-M2H MIP-7301-M2H MIP-7300-DMH MIP-7301-DMH MIP-7100-DVH-VC3 MIP-7100-M2H-VC3 MIP-7100-DMH-VC3 MIP-7101-DMH-VC3 MIP-7600-UVP-VC3 MIP-7600-APR-VC3 MIP-7601-APR-VC3 MIP-7300-M2H-VC3 MIP-7301-M2H-VC3 MIP-7300-DMH-VC3 MIP-7301-DMH-VC3 MIP-7100-VC3P MIP-7100-VC3R MIP-7100-VC3 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X HD X X X X X X X X X X X X X X X X X X X X X X X X X MPEG-2 Proxy Rec Play X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X DV/DVCPRO Rec/Play X AVC-Intra Rec Play Up /Down/ Cross Conversion and HD/SD Simulcast VC-3 Rec Play X X X X X X X X X X X X X X X X X X X X X X X X X Harmonic Technical Support: +888 673 4896 (Americas), +65 6542 0050 (Asia Pacific), + 44 1252 555 450 (EMEA), +7 495 926 4608 (Russia, CIS), +81 3 5565 6737 (Japan), +86 10 8391 3313 (China, mainland) X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X 28-0339 Rev. D