MediaPort 7000 Series Quick Reference Guide MediaPort Chassis (MPC-7002) Bezel Port Status Display Air Vents Power Indicator NOTE: Alarms will cause the display to flash. To stop flashing, resolve the alarm or touch the display. The Port Status Display allows you to enable the display of a static color bar pattern on any or all of the SDI Output connectors, which can be used to verify connectivity. For more details, refer to “MediaPort 7000 Series Front Panel” in the Spectrum Installation and Hardware Reference Guide. Status of Module A Status of Module B Port Status Display Health Summary Reference Input Channel 0: Player name, Player state, and mecode Channel 1: Player name, Player state, and mecode Environmental alarms, if any Health Summary Reference Input Channel 0: Player name, Player state, and mecode Channel 1: Player name, Player state, and mecode Environmental alarms, if any MediaPort Chassis Rear Panel Power Supplies and LEDs PS 0 PS 1 Module A Filler Panels Module B Power Supply LED States Off: No AC power to both units Green (blink): AC power present, unit on standby Green (solid): Power supply on and OK Red (blink): No AC power to this unit only Red (solid): Power supply failure NOTE: When a power supply fails, an audible alarm sounds. GPIO/Signal Assignments The MediaPort 7000 module has a female GPIO connector that can be connected to an external device and used to control players. For information on configuring GPIO using SystemManager, refer to “MediaPort Configuration” in the Omneon SystemManager User Guide. 9 8 7 6 5 4 3 2 1 18 17 16 15 14 13 12 11 10 26 25 24 23 22 21 20 19 GPIO Signals Function Pin Ground GPIO 0 GPIO 1 GPIO 2 GPIO 3 GPIO 4 GPIO 5 GPIO 6 GPIO 7 18 19 20 21 22 23 24 25 26 Harmonic Technical Support: +888 673 4896 (Americas), +65 6542 0050 (Asia Pacific), + 44 1252 555 450 (EMEA), +7 495 926 4608 (Russia, CIS), +81 3 5565 6737 (Japan), +86 10 8391 3313 (China, mainland) 28-0339 Rev. E MediaPort Modules 7000 Series Rear Panel Unused 13 1 2 3 4 6 5 15 RS-422 Port LEDs 14 Activity Activity Ethernet Port LEDs Activity 7 1. 2. 3. 4. 5. 6. 8 10 9 11 16 17 12 HD/SD SDI IN Channel A HD/SD SDI OUT Channel A (Primary) HD/SD SDI OUT Channel A (Secondary) HD/SD SDI IN Channel B HD/SD SDI OUT Channel B (Primary) HD/SD SDI OUT Channel B (Secondary) 7. 8. 9. 10. 11. 12. Status 18 LTC IN Channel A LTC OUT Channel A LTC IN Channel B LTC OUT Channel B Reference IN Reference Loop 13. 14. 15. 16. 17. 18. Soft Power button (middle) Status/Wink LED (bottom) GPIO/RS-422 connector RS-422 Port Service Use Only Ethernet/MediaDirector Installing a MediaPort Module To install a MediaPort module: Caution: Do not use the two lock screws on the rear 1. If you are installing two modules, you may need to panel of the module to pull it into position. Tighten the screws only after the module is fully inserted. first remove a filler panel from the chassis. From the rear of the MediaPort, unscrew the two lock screws that secure the filler panel, and then remove the filler panel. 2 1 2. Grasp the module handle and push firmly into the slot. Ensure the module is fully inserted by pressing on the connectors with the palm of your hand. 3. Tighten the two lock screws on the rear of the module to secure it to the chassis. 3 4. If installing two modules, repeat steps 1-3 for the second module. For complete replacement instructions, refer to the Spectrum Component Replacement Guide. Harmonic Technical Support: +888 673 4896 (Americas), +65 6542 0050 (Asia Pacific), + 44 1252 555 450 (EMEA), +7 495 926 4608 (Russia, CIS), +81 3 5565 6737 (Japan), +86 10 8391 3313 (China, mainland) 28-0339 Rev. E Replacing a MediaPort Chassis Power Supply To remove a power supply: 1. Disconnect the AC power cable. 2. Press the release lever to the right and pull the handle to remove the power supply. To install a new power supply: 1. Grasp the module handle and push firmly into the slot. 2. Connect the AC power cable. For complete replacement instructions, refer to the Spectrum Component Replacement Guide. Removing and Replacing a MediaPort Chassis Front Bezel 1 2 To remove the bezel: 1. Remove the center screws on each side of the chassis that secure the bezel to the chassis. . Note: Keep the rack ear in place. 2. Unplug the bezel power/data connector. 3. Pull the bezel away from the chassis. To install the new bezel: 1. Attach the bezel power/data connector. 2. Align the bezel in front of the chassis so that the Omneon logo appears in the top-left corner, and the metal corners of the bezel are level with the rack ears of the chassis. 3. Press the bezel straight onto the chassis. 4. Attach the two center screws on each side of the chassis to secure the bezel to the chassis. For complete replacement instructions, refer to the Spectrum Component Replacement Guide. Harmonic Technical Support: +888 673 4896 (Americas), +65 6542 0050 (Asia Pacific), + 44 1252 555 450 (EMEA), +7 495 926 4608 (Russia, CIS), +81 3 5565 6737 (Japan), +86 10 8391 3313 (China, mainland) 28-0339 Rev. E License Options for MediaPort 7000 Series Modules The following table shows available MediaPort 7000 Series module options. Model Number MPEG-2 H.264 Proxy Rec MIP-7300 MIP-7301 X Play X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X MIP-7600 MIP-7601 X Rec/Play X Rec ProRes VC-3 Play X Play AVC-Intra Rec MIP-7100 MIP-7101 DV/DVCPRO Play The following table shows MediaPort 7000 Series module license options. Product ID SD HD Up /Down/ Cross Conversion and HD/SD Simulcast APR X X X DMH* X X X DMS* X DVH X DVS X M2H* X M2S* X UVP X X X VC3 X X X VC3P X X X VC3R X X X X MPEG-2 Rec DV/DVCPRO AVC-Intra Play Rec/Play Rec Play X X X X X X X X X X X VC-3 ProRes Rec Play X X Play X X X X X X X X X X X X X SPL-PRORES X *For DMH, DMS, M2H, and M2S, MPEG-2 Rec and Play is only available on MediaPort 7300 Series modules. The following table shows additional licensed features available for MediaPort 7000 Series modules. Product ID SPL-OPC Description Onboard playout control for one channel of Spectrum ChannelPort or MediaPort 7000 SPL-OMF Onboard Media Fetch for one video server, enables Media Fetch for all OPC licenses installed SPL-STL Onboard subtitle insertion license for one channel of Spectrum ChannelPort or MediaPort 7000 For more details on the MediaPort 7000 module, refer to “MediaPort 7000 Series Reference” in the Spectrum Installation and Hardware Reference Guide. Harmonic Technical Support: +888 673 4896 (Americas), +65 6542 0050 (Asia Pacific), + 44 1252 555 450 (EMEA), +7 495 926 4608 (Russia, CIS), +81 3 5565 6737 (Japan), +86 10 8391 3313 (China, mainland) 28-0339 Rev. E