1. No category

MJ-1037 with KN-2550
UIM11008900 Ver00
R111223K6100-TTEC
SET-UP GUIDE
Warnings and Cautionary Points
• The unpacking and setup procedure shall be done by a qualified service technician.
• Be sure to unplug the power cable of the equipment before installing and setting up the product.
• Disconnect the ground wire after unplugging the power cable. In addition, be sure to connect the ground wire
before plugging the power cable.
• Install the equipment near an outlet. Be sure to wire the power cable securely so as to unplug it easily and not
to trip over it.
• According to the equipment model, these illustrations may differ.
„ Setup
1.
Remove the packing materials of MJ-1037.
2.
Take out the accessories.
MJ-1037
A
B
D
G
E
H
I
TBID
M4x10
a
J
TBID
M4x16
TBID
M4x16
TBID
M4x16
M4x6
b
d
e
f
M4x6
g
3.
i
j
n
Remove the packing materials of KN-2550.
© 2012 TOSHIBA TEC CORPORATION All rights reserved
MJ-1037 with KN-2550
1 / 13
4.
Take out the accessories.
KN-2550
N
5.
Cut out the gray portion shown in the figure
and dispose of it.
6.
Cut out the gray portion shown in the figure
and dispose of it.
7.
Open the cover.
© 2012 TOSHIBA TEC CORPORATION All rights reserved
P
M4x8
M3x6
M3x6
r
t
u
MJ-1037 with KN-2550
2 / 13
8.
Remove the screws and take off the cover.
• Screws: 3
9.
Remove the screw and take off the cover.
• Screw: 1
10. Cut out the gray portion shown in the figure
and dispose of it.
11. Wire the cable of [N] as shown in the figure.
N
12. Attach [A] to [N] with [r].
• r: 2
A
N
r
r
© 2012 TOSHIBA TEC CORPORATION All rights reserved
MJ-1037 with KN-2550
3 / 13
13. Insert [N] as shown in the figure.
N
14. Attach [N] with [a] and [b].
• a: 2
• b: 1
b
N
a
a
15. Attach [N] with [t].
• t: 1
N
t
16. Attach [P] with [u].
• u: 1
P
u
© 2012 TOSHIBA TEC CORPORATION All rights reserved
MJ-1037 with KN-2550
4 / 13
17. Connect the cable connector as shown in the
figure.
18. Attach the cover with the screw.
• Screw: 1
19. Attach the cover with the screws.
• Screws: 3
20. Close the cover.
21. Open the cover.
© 2012 TOSHIBA TEC CORPORATION All rights reserved
MJ-1037 with KN-2550
5 / 13
22. Insert [B] as shown in the figure.
B
23. Close the cover.
24. Attach [D] with [f].
• f: 1
D
f
25. Attach [E].
E
26. Insert [G].
G
© 2012 TOSHIBA TEC CORPORATION All rights reserved
MJ-1037 with KN-2550
6 / 13
27. Attach [H] with [g].
• g: 4
H
g
g
28. Attach [I] with [d].
• d: 2
d
I
29. Attach [J] with [e].
• e: 2
e
J
30. Insert [Q] by aligning the 2 pins as shown in
the figure.
Q
31. Check that the pins of the MFP and the holes
of [Q] are aligned properly.
* If not, adjust the height.
P.10 “Height Adjustment”
© 2012 TOSHIBA TEC CORPORATION All rights reserved
Q
MJ-1037 with KN-2550
7 / 13
32. Check that the pins of the equipment and the
holes of [Q] are aligned properly.
* If not, adjust the height.
P.10 “Height Adjustment”
Q
33. Tighten [i].
• i: 1
i
34. Open the cover.
35. Tighten [j].
• j: 1
j
36. Close the cover.
© 2012 TOSHIBA TEC CORPORATION All rights reserved
MJ-1037 with KN-2550
8 / 13
37. Take off the cover.
38. Connect the cable connector.
39. Attach the cover.
* Attach the cover so that the cable comes out
from the bottom.
40. Secure the cable with [n] as shown in the
figure.
* Cut out the unnecessary part of [n] and
dispose of it.
n
41. The setup is now completed.
© 2012 TOSHIBA TEC CORPORATION All rights reserved
MJ-1037 with KN-2550
9 / 13
„ Height Adjustment
1.
Pull out [Q].
Q
2.
Remove the screws and take off the covers.
• Screws: 2
• Covers: 2
3.
Open the cover.
4.
Remove the screw and take off the cover.
• Screw: 1
5.
Remove the screw and take off [R].
• Screw: 1
R
© 2012 TOSHIBA TEC CORPORATION All rights reserved
MJ-1037 with KN-2550
10 / 13
6.
Adjust the height of (A).
Adjust the height by rotating [bb], and secure it
by rotating [dd].
bb
dd
A
7.
Adjust the height of (B).
Rotate [bb] so that the height of (B) matches that
of (A), and secure it by rotating [dd].
bb
dd
bb
dd
B
8.
Adjust the height of (C).
Adjust the height by rotating [bb], and secure it
by rotating [dd].
C
© 2012 TOSHIBA TEC CORPORATION All rights reserved
MJ-1037 with KN-2550
11 / 13
9.
Adjust the height of (D).
Rotate [bb] so that the height of (C) matches that
of (C), and secure it by rotating [dd].
bb
dd
D
10. Attach [R] with the screw.
• Screw: 1
R
11. Attach the cover with the screw.
• Screw: 1
12. Close the cover.
© 2012 TOSHIBA TEC CORPORATION All rights reserved
MJ-1037 with KN-2550
12 / 13
13. Attach the covers with the screws.
• Screws: 2
• Covers: 2
14. Insert [Q] by aligning the 2 pins as shown in
the figure.
Q
© 2012 TOSHIBA TEC CORPORATION All rights reserved
MJ-1037 with KN-2550
13 / 13