1. No category

Undermount Slides
1A88F
Push-Open with Silent Soft-Closing
Undermount Slide for Face Frame Cabinet
(16mm)
Specifications
• Length: 305 / 381 / 457 / 533mm
12" / 15" / 18" / 21"
• Travel: Full Extension
• Maximum Drawer Side Thickness: 16mm(5/8")
• Max. Load Capacity: 34 kg(75 lb)/pair
• Mount: Undermount
• Material: Galvanized Steel
• Packing: Unit Packed in 2 pairs/carton
6 pairs/carton
Features
• Push-open, handle-free
• Enhanced silent soft-closing feature with light opening force
• Durable damping system with fast response capability
• All mechanical device, instead of electric-driven
• Safe, ergonomic and energy saving
• Undermount with full extension travel length
• Ultra smooth gliding motion with high rigidity and stability
design
• 2 dimensional trimming system provides tool-less height and
depth adjustments
• A tool-less adjustment system is available to permit minor
installation inaccuracies, thereby reducing assemblage
complexity.
• Effortless assembly and removal of drawer with front release
lever
• High installation allowances for drawer width: +0.5/-1mm,
and for drawer depth: +1/-1mm
Applications
• For Face Frame Cabinet : Kitchen Furniture, Kitchen Cabinetry,
Home Cabinetry and Box Drawers
1.10
King Slide reserves the right to alter specifications of all the products without notice. If the entity is different from the illustration, please refer to the entity.
Cabinet Depth with Bracket
www.kingslide.com
1
Space Requirement
Drawer Width Formula
W
Drawer Width
W: Internal Cabinet Width
Example:
Internal Cabinet Width = 457 mm (18")
Drawer Side Thickness = 13 mm (1/2")
+0.5
Drawer width = 457 - 16 = 441 -1.0 mm
= (18") - (5/8") = 17-3/8"
37(1-7/16")
min 27.5
13(1/2")
"W" minus
mm (inch)
10 (3/8")
12 (15/32")
14 (9/16")
16 (5/8")
18 (23/32")
Undermount Slides
Drawer Height
Drawer Side Thickness
Maximum 16mm(5/8'')
opening
min 6
+0.5
42 -1.0
Max = opening - 24mm(15/16”)
max 13mm (1/2”)
W-
Drawer Side Thickness
mm (inch)
16 (5/8")
15 (19/32")
14 (9/16")
13 (1/2")
12 (15/32")
21(13/16")
Dimension Specifications
Note: Holes other than those shown may be in the slide member at King Slide's
option and may change without notice.
Drawer Length
A
37(1-7/16”)
9(11/32”)
W
+0.5
W-42 -1.0
Note
min 6
X
10
(3/8”)
+2.0
System Screws
B
X
**4 -0
min gap
○
Chipboard Screws
Round Head Screw
max 16
(push-open)
4(5/32") max
max 13
bracket
37
Profile Length
Cabinet Depth with Bracket
21
min 27.5
W : Internal Cabinet Width
Note:
Ensure the slide is parallel to the horizon or tilt to cabinet front on both sides during
installation.
Drawer Length
mm (inch)
Overall Cabinet Depth
mm (inch)
1A88F305
305 (12")
1A88F381
381 (15")
1A88F457
1A88F533
Item No.
opening
6
1-7/16")
6")
Cabinet Depth With Bracket
mm (inch)
Profile Length
mm (inch)
System Screw Locations
mm (inch)
MAX
MIN
A
B
381 (15")
369 (14-9/16")
326 (12-7/8")
318 (12-1/2")
165 (6-1/2")
261 (10-1/4")
457 (18")
446 (17-9/16")
403 (15-7/8")
394 (15-1/2")
165 (6-1/2")
357 (14-1/16")
457 (18")
533 (21")
522 (20-9/16")
479 (18-7/8")
470 (18-1/2")
261 (10-1/4")
533 (21")
610 (24")
598 (23-9/16")
555 (21-7/8")
546 (21-1/2")
32
261 (10-1/4")
453 (17-13/16")
18
18
32
517 (20-3/8")
192
Fit with American standard 3" cabinet depth system.
32
96
288
Easy Assembly with Front-End Installation
Tool-less Height Adjustment :
Simply rotate the wheel at the front bottom of the drawer
to adjust the drawer height
Drawer Removal:
Simply press the front release device to
remove the drawer
Our specially designed front-end installation allows quick
and simple drawer installation and removal processes.
The quick connect and disconnect device is located at
the front-end under the drawer, keeping intact the elegant
appearance of the drawer.
King Slide reserves the right to alter specifications of all the products without notice. If the entity is different from the illustration, please refer to the entity.
1.11
9
37
Undermount Slides
Installation Instruction
1A88F & 1B88F
1. Before installing the slides, make sure the dimensions of the cabinet and drawer meet the requirements specified in Fig. 1 and ' Space Requirement'
drawing resectively for the slide to be installed.
2. Drill holes on the cabinet following the 'Installating Specification' drawing on the reverse page. Mount the slides and the rear brackets on the cabinet
using the recommended type of screws.
Locking Device
3. Make cut-outs on the drawer according to Fig. 2A 's dimension (Using the drill template FL00ZD0-A as page 1.39
is recommended) , then install
the front release lever according to Fig. 2B and 2C.
4. Pull out the slides on the cabinet.
Fig. 1
Extension Plastic
Front View
Dimension Specification
Installation Requirement
Fig. 2B
Normal lnstall
Locking Device with Extension Plastic
Drawer Length
X
37(1-7/16”)
33(1-13/16″)
rear notch
Note
10
(3/8”)
7(9/32″)
+2.0
**4 -0
min gap
(push-open)
0
4(5/32") max
11(7/16″)
B racket
Profile Length
Ø6*10
Cabinet Depth
Locking Device
Locking Device
Extension Plastic
Fig. 2C
Extension Plastic
Inset lnstall
Y
Blocking Behind Frame
X
Note
Normal lnstall
21
Locking Device with Extension Plastic
(13/16")
Drawer Length
X
33(1-13/16″)
rear notch
◎Slide bottom can not be lower than opening
37(1-7/16”)
Note
Drawer Length
Normal lnstall
Z ( setback ) = (X +**4 ) + 4 (max)
10
X
(3/8”)
Fig. 2A
bracket
Min = L + Z + 5(3/16")
Max = L + Z + 48(1-15/16")
+2.0
**4 -0
min gap
10
(3/8”)
(push-open)
37(1-7/16”)
0
Note
4(5/32") max
11(7/16″)
7(9/32″)
B racket
Profile Length
+2.0
**4 -0
xmin gap
0
Y
Z
16
57
24
Inset Install Formula
(push-open)
Cabinet Depth
17
18
19
20
21
4(5/32") max
58
59
60
61B racket 62
Profile Length
25
26
27
28
29
Cabinet Depth
7(9/32″)
33(1-13/16″)
rear notch
Locking Device with Extension Plastic
32(1-1/4'')
16(5/8'')
Ø6*10
22
63
30
14
(9/16")
2(3/32'')
12
(15/32")
11(7/16″)
You can use optional drill template
Ø6*10
FL-00ZD0-A as page 1.39
*Minimum 3 screws per bracket
L: Slide Length X: Front Panel Thickness
Inset lnstall
Y
Blocking Behind Frame
X
Note
Note:
O
Inset lnstall
Y
Blocking Behind Frame
Ensure the slide is parallel
to the horizon
X
◎Slide bottom
can not be lower than opening
or tilt to cabinet front on both sides
during
Note
bracket
installation.
Z ( setback ) = (X +**4 ) + 4 (max)
X
Rear Bracket
21
(13/16")
32(1-1/4'')
Min = L + Z + 5(3/16")
Max = L + Z + 48(1-15/16")
21
(13/16")
◎Slide bottom can not be lower than opening
Z ( setback ) = (X +**4 ) + 4 (max)
bracket
32(1-1/4'')
Min = L + Z + 5(3/16")
Max = L + Z + 48(1-15/16")
Inward
1.0mm
*Minimum 3 screws per bracket
2(3/32'')
14
(9/16")
12
Inward
(15/32")
1.0mm
16(5/8'')
2(3/32'')
14
(9/16")
12
(15/32")
*
*
O
X
King Slide reserves the right to alter specifications of all the products without notice. If the entity is different from the illustration, please refer to the entity.
adjustments here can fine-tune the slide fun
* The
If the issues still exist after the adjustments, plea
*Minimum 3 screws per bracket
1.14
*Closing System Adjustments
16(5/8'')
Z ( setback ) = (X +**4 ) + 4 (max)
bracket
Z ( setback ) = (X +**4 ) + 4 (max)
Min = L + Z + 5(3/16")
◎SlideMin
bottom
than opening
= can
L +not
Z be
+ lower
5(3/16")
Max = L + Z + 48(1-15/16")Ø6*10
Max = L + Z + 48(1-15/16")
B racket
file Length
Cabinet Depth
Z ( setback ) = (X +**4 ) + 4 (max)
(13/16")
32(1-1/4'')
32(1-1/4'')
bracket
www.kingslide.com
Min = L + Z + 5(3/16")
32(1-1/4'')16(5/8'')
16(5/8'')
Max = L + Z + 48(1-15/16")
*Minimum 3 screws per bracket
*Minimum 3 screws per bracket
locking Behind Frame
*Minimum 3 screws per bracket
O
16(5/8'') 2(3/32'')
14
(15/32
1
21
5. Position and align the drawer with the slide as shown in Fig. 3A
and 3B. Push
the (13/16")
drawer all the way into the cabinet as shown in Fig. 3C until
O
X
O
X
n not be lower than opening
clicked to complete the installation.
6.bracket
After confirming the drawer is operating normally, install theO
front panel. X
32(1-1/4'')
+ Z + 5(3/16") 7. If
+ Z + 48(1-15/16")
height / depth adjustment is needed after installation, please refer to the Detail Adjustment Info. below or the feature diagram on the previous
page.
Fig. 3A
Notice
14
(9/16")
2(3/32'')
*Minimum 3 screws per bracket
*Closing System Adju
12
(15/32")
Inward
Inward
1.0mm
1.0mm errors
installation
Inward
Inward
1.0mm
To prevent
which may lead to the
1.0mm
drawer getting stuck, Please make sure the nomal
operation of the drawer before securing the front
panel.
*
Fig. 3B
X
*
Undermount Slides
*Closing Sys
*Closing Sys
16(5/8'')
OFig. 3C
12
(9/16")
2(3/32'')
X
(9/16")
2(3/32'')
ote
**4 ) + 4 (max)
14
14
(9/16")
Inward
Inward
1.0mm
1.0mm
Outwa
*
*
*
Detail Adjustment Info
**
**
Inwa
The adjustment
The adjustment
The adjustments
herestil
ca
If the issues
If the issues stil
If the issues
afte
resetstill
to exist
default
reset
to
default
reset to dimension
default settings
is ina
dimension
is in
dimension
is in accordan
*Closing System Adjustments
Front Gap Adjustment
FrontFront
Gap Adjustment
Gap Adjustment
Outward
Outward
Outward
Inward
1.0mm
Inward
1.0mm
Factory
setting
Factory
settingsetting
4.0
Factory
4.0
4.0
+2.0
+2.0
+2.0
Inward
Inward
Inward
*
*
adjustments here can fine-tune the slide function.
* The
If the issues still exist after the adjustments, please
reset to default settings and ensure each installation
dimension is in accordance with the specification.
Front Gap Adjustment
Outward
Factory setting
Inward
4.0
+2.0
Inward
Outward
Notes for installation
1. Ensure the drawer body appearance is upright. It could not be diamond trapezoidal or distorted!
2. Ensure the side space, depth on both sides are consistent.
3. Ensure the installation location or the cabinet is on a flat surface.
4. Ensure the front release lever is installed correctly.
5. Ensure the drawer dimensions, rear notch locking hole, internal drawer width, and the drawer bottom recess are correct.
King Slide reserves the right to alter specifications of all the products without notice. If the entity is different from the illustration, please refer to the entity.
1.15