VEHICULAR SLIDE GATE OPERATOR Commercial DC Model CSL24VDC Gate Operator and Accessory Site Plan 1 2 3 4 5 6 7 8 9 10 1 5 Imagine your Customers being at the office and receiving an alert if they left their garage or gate open. Or being able to turn on their lights before they get home. The 828LM Internet Gateway, which connects to your Customer’s router and enables smartphone control, does this by letting them monitor, open and close their garage door or gate from anywhere and control home lighting. 1 10 2 Standard edges will cause a gate to stop or reverse when it meets an obstruction while closing. 6 MPEL Mounting Plate for Post Mounting For post mounting model CSL24VDC commercial slide operator. Posts not included. MSEL Mounting Stand 892LT & 894LT 2-Button and 4-Button Security+ 2.0™ Learning Remote Controls 65-MG020-5 Sensing Edge (Non-Monitored) Internet Gateway 2 MyQ® Enabled Indoor Controls Remote Controls Photoelectric Sensors Loop Detectors Edge Sensors Mounting Plate and Stand Solar Batteries Heater dwellingLIVE 828LM* Steel stand for mounting to concrete pad. 7 These remote controls are ideal for gated communities. One button can control a gate operator and the other(s) can control a garage door. It can also be programmed to different codes and frequencies. SOLPNL20W12V 20 Watt 12V Solar Panel Ideal for remote and sunny areas without access to an AC outlet. Two required. SOLPNL10W12V 10 Watt 12V Solar Panel 811LM & 813LM Universal DIP Single-Button and 3-Button Remote Control Two required. 8 7 5 29-NP712 7Ah 12V Battery These remote controls are ideal for applications such as gated communities or commercial applications requiring a large number of remotes for a common entrance. Standard 7 AMP-Hour Battery, 12 Vdc, to replace original batteries provided with operator. Reuse existing harnesses. A12330SGLPK 3 3 8 The photoelectric sensors are designed to detect an obstacle in the path of the electronic beam and stop the operator. Includes mounting brackets. 9 9 Low power through beam photoelectric sensors, 45 foot sensing distance, NEMA 4 rated. Works in conjunction with Power Management System to save power. Customer: Date: LOOPDETLM Plug-In Loop Detector Plug-in Loop Detector, (LOOPDETLM) innovative design includes 8 sensitivity settings & boost, ensures vehicles are easily identified. Project: Architect/Engineer: Contractor: Gate Weight (lbs.): Heater kit for pad mount operators. Protects system to -40ºF. Installs on operator frame. 10 dwellingLIVE Advanced Visitor Management and Access Control Solution • Credentialed Access 4 ORDER SUMMARY HTR Heater Kit Photoelectric Sensor (Monitored) LiftMaster gate operators comply with UL 325 standards. Important: To be compliant with UL 325 and industry safety guidelines, qualified monitored external entrapment protection devices such as photoelectric sensors or edge sensors are required to be installed with this operator. LiftMaster.com Upgrade 33 AMP-Hour Battery, 12 Vdc. Ideal for solar applications and extended battery backup. Two required. CPS-UN4 4 Power Source (120 or 240 VAC): 33Ah 12V Battery Photoelectric Sensor (Monitored) 6 Gate Length (ft.): CPS-RPEN4GM Solar (Y/N): * LiftMaster® Internet Gateway Accessory functionality is dependent on communication with a MyQ® Enabled gate operator. MyQ® Technology communication can be limited by distance and type of exterior building materials. A general range estimate is 300 ft. • Visitor Management • Telephone Entry Systems • License Plate Recognition • Community Websites • Mobile Patrol • Front Desk Concierge VEHICULAR SLIDE GATE OPERATOR Commercial DC Model CSL24VDC Installation Blueprint TYPICAL INSTALLATION INSTALLATION DIMENSIONS OPERATOR POWER SOURCE NOTE: One or more non-contact sensors shall be located where the risk of entrapment or obstruction exists at either the opening or closing direction. Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle, trips the sensor while the gate is still moving. Any gap between the gate and a fixed object such as a wall, pillar, column or the operator itself larger than 2 1/4 inches must be filled. Wire Gauge 120 Vac 240 Vac 14 130 feet 260 feet 12 205 feet 410 feet 10 325 feet 650 feet 8 520 feet 1040 feet 6 825 feet 1650 feet 4 1312 feet 2624 feet OPERATOR DIMENSIONS DETERMINE LOCATION FOR CONCRETE PAD AND OPERATOR 20" 4"(10 cm) 21.1" 26" (66 cm) NOTE: Use copper conductors ONLY. SINGLE GATE Warning Sign Safety Catch Roller 14.6" 24" (61 cm) Edge Sensor CONCRETE PAD AND OPERATOR ATTACHMENT Edge Sensor Photoelectric Sensors CONDUIT LOCATION 4 Concrete Anchors 1/2" x 3 1/2" Operator 5-5/8" 1/2" MOUNTING FOOTPRINT (Gate) 7" 11.9" 1-1/4" 3-1/2" min. 1-2" 2-3/4" 10.3" 2-1/4" 2.85" 1-3/8" Check national and local codes for proper depth (Conduit) 6" Above Ground Earth Ground Rod .63" 10.4" 14.1" 26" Below the frost line. Check all national and local codes. Water Tight Conduit (Not provided) 8" NOTE: Power and control wiring MUST be run in separate conduits. DUAL GATE 13" 23" Safety Catch Roller Warning Sign 26" (66 cm) 24" (61 cm) 4-1/2" 14.6" 15" (Pad) 24" Edge Sensor SAFETY LAYOUT Monitored Photoelectric Sensors Operator Sensors for Open Cycle NOTE: Wired connection in a dual gate setup is optional. Operators can be setup for wireless dual gate communication. Edge Sensor ! © 2014 LiftMaster All Rights Reserved 845 Larch Ave., Elmhurst, IL 60126 LiftMaster.com 01-37414B e id ty ts r u e O op r P Check national and local codes for proper depth NOTE: Power and control wiring MUST be run in separate conduits. e y id rt s e In op r Earth Ground Rod P Water Tight Conduit (Not provided) ey id t s er In p ro P Photoelectric Sensors PrOuts op id ert e y Sensors for Close Cycle
© Copyright 2024