1. No category

HELPY QUICK 12V
START-UP GUIDE
HELPY QUICK 12V
GSM500
(5CT-061)
GSM200
(5IG-004)
ALARM SYSTEM CONFIGURATION:
- HELPY QUICK 12Vdc - to be placed behind COP (5HE-310)
- Passive handsfree terminal with emergency pushbutton
to be placed on the cartop (5HV-004 / 5HV-021)
- Passive handsfree terminal with emergency pushbutton
to be placed in the carbottom (5HV-004 / 5HV-021)
- Telephone handset - to be placed in the machine room
- GSM200 gateway
OR
- Universal GSM500 GC gateway OR analog external line
OR
Passive handsfree
terminal with pushbutton
CAR-TOP
(5HV-004)
HELPY QUICK
5HE-310
Power supply
+12 Vdc
Telephone
handset
4TS-101
Passive handsfree
terminal with pushbutton
CAR-BOTTOM
(5HV-004)
HELPY QUICK - CONNECTIONS
CONNECTING THE TELEPHONE
“-”
“TEL”
1. Connect the RJ11 to the telephone
2. Connect the conductors to the
terminal block “TEL” and “-” of the
autodialer.
GSM GATEWAYS- INSERTING THE SIM CARD
Make sure GSM is completely turned o˜ before you insert the SIM card
GSM500
GSM200
Press the plastic case oper by using
a screwdriver.
Insert/replace the SIM card by acting
on the SIM card holder.
GSM500
GSM200
UNIVERSAL GSM500-GC GATEWAY
SUPPLYING THE UNIVERSAL GSM500-GC GATEWAY
Insert the Sim Card and than connect the built-in battery pack.
INSERT THE CONNECTOR INTO
THE DEDICATED SOCKET
For connection of the external power supply and the telephone line, please use either the dedicated plugs
or the built-in screw terminals.
PLUG RJ11 Telephone line
Telephone line
Power supply
+ 12 Vdc
Adapter 230 Vac / 12Vdc
HELPY QUICK - CONNECTIONS
GSM500
PLUG RJ11
Power Supply
+ 12 Vdc
OR
Analog telephone line
GSM200
RJ45
RJ45
1. Set the jumpers as shown above
2. Enter the programming and dial
661
HELPY QUICK - CONNECTIONS
CONNECTING PASSIVE HANDSFREE TERMINAL WITH PUSHBUTTON (CAR-TOP)
viva voce
TETTO CABINA
1. Connect the terminal block “B” of the
handfree terminal to the terminal block
“MIC3” of the autodialer
2. Connect the terminal block “A” of the
handfree terminal to the terminal block
“ALT2” of the autodialer
3. Connect the terminal block “-” of the
handfree terminal to the terminal block
“-” of the autodialer
4. Connect one of the handsfree terminal’s
pushbutton contact to the terminal
block “-” of the handsfree terminal
5. Connect the free pushbutton contact
of the handsfree terminal to the terminal
block “AL2” of the autodialer.
MIC3
ALT2
“-”
AL2
Pulsante
The connection cable between the passive handsfree terminal and the
autodialer must be shielded.
CONNECTING PASSIVE HANDSFREE TERMINAL WITH PUSHBUTTON (CAR-BOTTOM)
1. Connect the terminal block “B” of the
handfree terminal to the terminal block
“MIC2” of the autodialer
2. Connect the terminal block “A” of the
handfree terminal to the terminal block
“ALT2” of the autodialer
3. Connect the terminal block “-” of the
handfree terminal to the terminal block
“-” of the autodialer
4. Connect one of the handsfree terminal’s
pushbutton contact to the terminal
block “-” of the handsfree termina
5. Connect the free pushbutton contact
of the handsfree terminal to the terminal
block “AL2” of the autodialer
viva voce
FONDO CABINA
AL2
“-”
ALT2
MIC2
The connection cable between the passive handsfree terminal and the
autodialer must be shielded.