Download Report

Part names and features
745 Driver
945 Driver
F45 Fairway wood
Accessories
01
Tuning weight
Tuning weight
Change out weights to precisely tune
Center of Gravity (CG) height.
Change out weights to precisely tune
Center of Gravity (CG) depth and height.
QTS sleeve
QTS sleeve
Change position to set desired
face angle, lie angle, and loft angle
Change position to set desired
face angle, lie angle, and loft angle
Weight port (center)
Weight port (back)
Weight port (center)
545 Driver
Custom torque wrench
Custom pouch
Use only the torque wrench
and tuning weights provided.
Use of damaged or
improperly installed
tuning weights may result
in injury or product damage.
02
How to install and remove QTS sleeve
1
Hold the club upright with
the grip resting on the ground.
Use this position when loosening
and tightening.
2
Supporting the head in your hand,
gently insert the torque wrench
into the screw hole.
(Torque wrench operation)
Tighten
3 Loosen
4 With
With the torque wrench aligned
the torque wrench aligned
with the shaft,
turn it counterclockwise.
with the shaft, turn it clockwise
until you hear a 'click'.
Click
Shaft and torque
wrench should
form a straight line
* Be careful not to loosen the screw too much,
as you may drop the screw and lose the washer.
Do not use any tool other than the supplied torque wrench.
Also do not use the supplied torque wrench on any other products.
Always tighten until you hear a 'click'.
Damaged QTS sleeve and/or improperly installed
QTS sleeve may result in injury or product damage.
* Not compatible with SRIXON Z-STAR series torque wrenches.
Once you hear a 'click', stop tightening.
Position the torque wrench so that it is correctly aligned with the shaft.
Screws fastening the QTS sleeve employed on the driver
and fairway woods are designed for respective specifications
and are not interchangeable.
Failure to insert the tip of the torque wrench firmly
into the screw hole may result in damage to the screw.
03
Improperly aligned
torque wrench
Failure to tighten until you hear a 'click' may result in separation of the club head or product damage.
Over-tightening may damage the QTS sleeve.
04
How to remove and install QTS sleeve
5 Insert the shaft into the head
Align the position line with
the ★ mark and press straight in.
* Illustration shows neutral position
(Sleeve installation)
6 QTS setting examples
For right position
(Open face)
Align the ★ mark on the head with the 'R'
on the QTS sleeve and press straight in.
For left position
(Closed face)
Align the ★ mark on the head with the 'L'
on the QTS sleeve and press straight in.
The shaft may not insert fully if the position line
and sleeve mark are not correctly aligned.
Press the shaft all the way
in until the QTS sleeve is completely covered.
05
06
How to change tuning weights
Locked
mark on weight
aligned with
“LOCK ” mark on head
1
Unlocked,
ready for removal
mark on weight
aligned with
“ UNLOCK” mark on head
Pull the torque wrench directly
up to remove the weight.
* If the weight is difficult to remove even
with the mark on the weight aligned
with the “ UNLOCK” mark on the head,
lightly jiggle and pull the tuning weight
at the same time with torque wrench
still inserted.
3
Place the desired tuning weight on
the tip of the custom torque wrench,
insert it into the weight port,
and rotate it 45˚ clockwise to the
“LOCK ” position to lock it.
* Do not turn the tuning weight past
the locked position.
Hold the clubhead securely in one hand
and the custom torque wrench in the other.
Insert the custom torque wrench
straight into the hole in the center of
the tuning weight and rotate it 45˚
counterclockwise to the
“ UNLOCK” position to unlock it.
Do not use any tool other than the supplied torque wrench.
Also do not use the supplied torque wrench on any other products.
Do not turn the tuning weight past the unlocked position.
Improper installation of the tuning weight may result in injury or product damage.
Do not rotate more than 45˚.
Ensure that the tip of the custom torque wrench is fully inserted
into the hole of the tuning weight.
Hold both the custom torque wrench and the clubhead securely while exchanging the weights.
07
2
Improper installation of the tuning weight may result in injury or product damage.
When installing or removing the tuning weights, rotate them only 45˚ until they reach the
“LOCK ” or “ UNLOCK” position respectively. Do not attempt to turn the weight more than 45˚,
as it may damage either the tuning weight or the weight port.
08
QTS sleeve performance guide
Select from 12 different positions to set your preferred face angle,
lie angle, and loft angle.
The sleeve is set to N (Neutral) at time of purchase.
Refer to the guide to set your preferred trajectory.
Lateral range of adjustment depending on sleeve position
Flight can be adjusted laterally by approx. 37 yards (W/Driver)
10
11
7
2
3
High trajectory
12
8
6
1
Low trajectory
9
4
5
Approx. 37 yards
Draw
09
Fade
10
QTS sleeve position overview
1
Initial
2
3
4
5
6
7
8
9
10
11
12
Position
Face positioning
Lie angle
11
N
Neutral
R
Right
NU
Neutral Upright
L
Left
Straight face
Open face
Straight face
Closed face
Standard
Moderate upright
Upright
Moderate upright
0
0
-2.0°
+1.0°
0
+2.0°
+2.0°
+1.0°
12
Tuning weight performance guide
745 Driver
945 Driver
F45 Fairway wood
545 Driver
Weight port (center)
Weight port (center)
Weight port (back)
If ball flight is too high (ball tends to rise):
If ball flight is too low (ball tends to drop):
If ball flight is too high (ball tends to rise):
If ball flight is too low (ball tends to drop):
A heavier weight promotes a stronger flight
and more roll (especially into the wind). A lighter weight delivers distance
with longer carry.
A lighter weight promotes a stronger flight
and more roll (especially into the wind).
A heavier weight delivers distance
with longer carry.
Heavy
Installing a heavy weight lowers
the CG to deliver
a low-spin trajectory.
Light
Installing a light weight raises
the CG to achieve
the appropriate amount of spin.
Light
Heavy
Trajectory—initial settingg
TTrajectory after tuningg
Trajectory—initial settingg
TTrajectory after tuningg
Installing a heavy weight
on the center and
a light weight on the back side
creates a shallower CG
which reduces spin.
Trajectory—initial settingg
TTrajectory after tuningg
Heavy
Light
Installing a heavy weight
on the back side and
a light weight on the center
creates a deeper CG
that increases spin appropriately.
Trajectory—initial settingg
TTrajectory after tuningg
Extra weight cartridges
(sold separately)
Made in China
13
3g (titanium)
4g (stainless)
5g (stainless)
6g (stainless)
7g (stainless)
8g (tungsten-nickel)
9g (tungsten-nickel)
10g (tungsten-nickel) 11g (tungsten-nickel)
14
Important
To ensure a safe and satisfying golfing experience, please be sure to follow these Important Precautions.
Precautions Be sure to read the Important Precautions carefully and exercise appropriate care. The manufacturer assumes no liability for injury or product damage due to failure to comply with the instructions herein.
Before using
Rules of Golf
Carefully inspect the QTS sleeve and tuning weight prior to each round
of golf or practice session to confirm that they are properly secured.
You may not change the QTS sleeve position
or exchange weights during a round.
1
Check to see that the tuning weight is locked securely
in position.
If the tuning weight is not secured firmly in the weight port when
swinging the club during a game or practice session, there is
a possibility that the weight could fly off, injuring either you or a bystander.
SRIXON Z Series clubs conform with R&A-approved Rules of Golf. However, it is against
the rules to modify club performance during a round by changing the QTS sleeve position
or exchanging weights to change the CG position, as this breaches the Rules of Golf
regulation 4-2a, which states: “During a stipulated round, the playing characteristics of
a club must not be purposely changed by adjustment or by any other means.”
2
15
Confirm weight is locked in position
Unlocked, ready for removal
mark on weight aligned with
“LOCK ” mark on head
mark on weight aligned with
“ UNLOCK” mark on head
Check to see that the QTS sleeve is properly secured.
Tighten the sleeve until you
hear a 'click'. If you fail to
properly secure the sleeve,
there is a possibility that the
head may come off in mid
swing, injuring either you
or a bystander.
16
Important
To ensure a safe and satisfying golfing experience, please be sure to follow these Important Precautions.
Precautions Be sure to read the Important Precautions carefully and exercise appropriate care. The manufacturer assumes no liability for injury or product damage due to failure to comply with the instructions herein.
Care and storage
17
1
Only remove the QTS sleeve or tuning weights when making adjustments.
All parts should remain properly installed at all other times,
including when the club is in storage, to ensure that no foreign objects
or debris become lodged in the sleeve connection or screw holes.
2
When removing the QTS sleeve or tuning weights, be sure
that you do so in a clean location to ensure that no foreign objects
or debris become lodged inside.
Installing the tuning weight while there are foreign objects
or debris in the weight port may damage either the weight
or the port, or prevent proper installation or removal
of the tuning weight.
It may even cause internal damage to the club head,
adversely affecting club performance.
3
If the QTS sleeve or weight ports become soiled
with water, dirt, or other debris, wipe them clean
with a cotton swab or a soft, clean cloth.
4
Do not heat the QTS sleeve
as it may damage the product.
5
Avoid adjusting the QTS sleeve or changing weights
when the temperature is below -5˚C or above 45˚C,
as it may damage the plastic components in the weight port.
6
Please be aware that attempts to remove the QTS sleeve or intentionally
disassembling it may not comply with the manufacturer’s warranty.
* For information on manufacturer's warranty regulations,
please refer to the owner's manual and warranty included with your golf club.
18
SRIXON /CLEVELAND GOLF
5601 Skylab Road
Huntington Beach, Ca 92647
[email protected]
714.889.1300