Download Report

Compriband Super FR
Fire Rated Acrylic Impregnated Foam Sealant Strip
Description
Compriband Super FR is an acrylic
impregnated foam sealant strip which
when used under compression by 80%
provides a fire seal for up to 4 hours in
accordance with BS 476 Part 20 or for
longer periods when used in
conjunction with Alfasil FR or Alfacryl
FR. At 80% compression the product
also provides a high performance
weatherseal (>600 Pa). The product is
supplied in roll form pre-compressed
and ready for immediate use with a
self-adhesive backing. After
positioning, the material expands to
find its own level and creates a
permanent elastic seal. The product
remains flexible throughout its life and
responds to continual expansion and
contraction cycles caused by thermal
and structural movement.
Typical Uses
Compriband Super FR is designed to
be used for the linear sealing of
movement joints in substantially brick,
stone and cementaceous building
elements for example in walls,
partitions, around window and door
frames, sectional buildings and
insulated cladding panels.
Surface Preparation
No special surface preparation or
primers are required but contact
surfaces must be clean of dust, dirt,
loose matter, grease and oils.
Application
Care must be taken not to stretch the
material, especially at joints. Do not run
Compriband Super FR around corners always make close fitting butt joints.
Continuous seals are formed with taper
lap or close fitting but joints.
Instructions for use are enclosed in
each carton supplied and should be
followed closely. The material expands
at a rate dependent on the ambient
temperature, expanding faster in
warmer conditions. If required the rate
of recovery may be delayed by cooling
in a freezer immediately prior to
installation. Alternatively, the recovery
can be accelerated by warming the
material after installation using an
indirect heat source.
Storage
Store rolls horizontally and in original
packaging between +5°C and +25°C in
dry conditions and away from direct
sunlight. Shelf life is approximately 12
months.
Health and Safety
The product is not regarded as having
any significant associated hazards. No
special precautions are necessary but
the use of gloves are recommended
during handling and installation of the
product, especially for persons with
sensitive skin. Wash hands immediately
after use. Material Safety Data Sheet is
available upon request.
Compriband Super FR
Tremco illbruck Limited
Bentall Business Park, Glover
Washington, Tyne & Wear NE37 3JD
Tel: 0191 419 0505 Fax: 0191 419 2200
Email: [email protected]
Website: www.tremco-illbruck.co.uk
Availability – Standard Sizes
Size
Gap Size mm
2
3
4
5
6
8
10
12
16
20
25
2
2-3
3-4
4-5
5-6
7-8
9-10
10-12
14-16
17-20
22-25
Recommended Tape
Width / Joint Depth (mm)
40
40
40
40
40
40
40
40
40
50
60
Expanded
Thickness (mm)
10
15
20
25
30
40
50
60
80
100
125
Roll Length
(m)
8
6
6
4
4
4
4
4
3
3
3
All dimensions are subject to tolerances. If dimensional tolerances are of particular interest please consult the sales office.
Physical Properties
Characteristic
Impregnation system
Adhesive coating
Colour
Density
Dimensional tolerances
Tensile Strength
Extension at Break
Elastic recovery
Rain Resistance @ 80% compression
(supplied pre-compressed by approx 85%)
Fire Class
Units / Test Method
ISO1798
ISO1798
%
Specification
Acrylic polymer
Acrylic with carrier and red thread
Mid / pale grey
80 Kg.m-3
Nominal +/- 5%
>200 kPa*
>200%*
> 95
NEN6069
> 600 Pa
DIN4102 Part 1
BS 476 Part 20
10mm Vertical Joint
Fire resistance (detailed
independent test report
available upon request)1
Operating Temperature
Thermal Conductivity
Mould Resistance
Biological Root Penetration
Effect of water, salts and alkalis
Compatibility
Dimensional tolerances
20mm Vertical Joint
NEN 6069
°C
W/m/K
DIN 4062
B1
> 4 hours
> 5 hours with Alfasil FR
>5 hours with Alfacryl FR
>3 hours
> 5 hours with Alfasil FR
> 5 hours with Alfacryl FR
>60 min
-30 to +90
0.065
Yes
None
None
Most sealants and common
building materials
Nominal +/- 5% or 1 mm
which ever is greater
* Excluding adhesive layer
1
ISSUE 3 04/12/2007
The fire resistance of Compriband Super FR depends upon:
1. The width of the joint to be sealed
2. The depth of joint to be sealed
3. The type of structure involved.
4. The compression factor used.
5. Whether or not an appropriate capping sealant is used.
a brand of
ABCD
Whilst every care has been taken in the preparation of this information, no warranty is given or implied in
connection with any recommendation or suggestion made herein or by our Representatives, Agents or
Distributors. We reserve the right to modify specifications from time to time without prior notice. Users are
advised to conduct their own tests in order to determine the suitability of the Product for the intended
purpose. All goods are supplied subject to standard Conditions of Sale which are available upon request.