Veneer Bookcase Code: 9548 IMPORTANT-READ CAREFULLY-RETAIN FOR FUTURE REFERENCE 9. Fit the Back Stabilizers You need: 6x Back Stabilizers Attach the 6x Back Stabilizers to the outside of the back of the unit in the positions shown using the 6x pre-fitted screws. Push the narrow end of the Stabilizer between the groove and the Back Panel. Tighten each screw to make the structure rigid. Welcome Care of your Product Thank you for buying the Veneer Bookcase. Before beginning assembly, please take a few quiet minutes to read these instructions. Lay the parts out on a clean, soft, flat surface (such as a carpeted floor) and compare with the parts check list on the next page. Do not throw away any packaging until you are sure that you have all the parts. If, for any reason, you wish to return the product, you must disassemble the components and use the original packaging. The product must be assembled by an adult. There are small parts: keep small children clear of the assembly area. Some stages of assembly require more than one person. Product Care Ÿ Clean your Bookcase by wiping with a damp cloth & drying with a soft cloth. Never clean with abrasives, chemical cleaner or household polishes. Ÿ Take care when handling or moving the furniture. Careless handling can damage wooden furniture, Try to lift rather than drag. Product Safety Ÿ Periodically check that all assembly fixings are tightened properly, care should be taken to ensure 10. Fit the Wall Strap. You need: 1x Wall Strap, 1x Small Domed Screw and a Screwdriver. Please Note: Use of the Wall Strap is only Not essential when used in conjunction with an appropriate Aspace bed. Fit the Wall Strap with the 1x Small Screw into the back of the unit as shown. With a minimum of two people, move the unit up against the wall. Fix the other end of the Strap to the wall, using fittings appropriate for that wall. This work should only be carried out by a competent person. Because of the diverse nature of walls, wall plugs and screws have not been supplied with the Wall Strap. If you are at all unsure of the type or suitability of the wall, or of the appropriate fixings seek professional advice. that no fittings are loose. Ÿ The furniture must be set up on an even and stable surface. Ÿ Keep away from direct sources of heat, such as electric, gas or coal fires. Ÿ Do not allow children to climb on the furniture. Using this furniture other than for its intended purpose could cause damage to the structure or serious injury to your child. Ÿ The Bookcase should not be used if any structural part is broken or missing Ÿ Do not attach items such as ropes, strings, cords, harnesses or belts etc to avoid the risk of strangulation. Ÿ Warning: Children can become trapped between the bed and the wall. To avoid the risk of serious injury the distance between the top safety barrier and the wall must not exceed 75mm or be more than 230mm. Customer Service 0845 872 2400 If you have a problem with this product, please call our Customer Service Team who will be glad to help. We can usually provide replacement and / or spare parts promptly; it will help us if you can identify the specific part using the check list in the next section. About ASPACE Many of us at ASPACE are parents. Despite occasional urges to pack them off to the workhouse we know what a pleasure it is to provide one’s children with a lovely space where they can feel cosy, secure, loved and in charge (well, up to a point!). Our mission at ASPACE is to allow you to give them that space of their own. Our furniture is available exclusively from ASPACE and is designed and specified by us with children in mind. We wish you and them many happy years with it. 5 8 1 Parts Check List (not to scale) CR 8. Fit the Shelf. You need: 4x Shelf Studs. Parts Check List. 2x Back Panels 1x Bookcase Plinth 1x Back Panel Divider 1x Shelf 1x Bookcase Side Left 1x Bookcase Side Right 1x Bookcase Top 1x Bookcase Base Fit 2x Shelf Studs into the required pair of small holes on the inside face of each Side as shown below. Ensure that the Shelf Studs are positioned at the same level on both sides. Carefully place the Shelf into the Unit ensuring that it rests evenly on the shelf studs. 13x Dowels 8x Cam Pins 8x Cams 4x Feet 1x Wall Strap 3x Screws for Back Stabilizers 3x Back Stabilizers 1x Domed Small Screw (for wall strap) 4x Shelf Studs You may also need a Screwdriver 60 5 2 mm Ruler to scale. 7 6. Attach the remaining Side. Assembly 1. Prepare the Base and Plinth. You need: 2x Cams and a Screwdriver. You need: 9x Dowels. Carefully lower the remaining Side onto the rest of the Assembly ensuring that all the Cam Pins and Dowels are correctly engaged into each of their corresponding holes. Also make certain that the edges of the Back Panels locate correctly into their corresponding grooves. Once all is engaged, insert 2x Cams into the holes in the underside of the Base. Turn the Cams clockwise with a Screwdriver to secure. Lay the Base and Plinth down on a flat soft surface (such as a clear carpeted floor) and insert 4x Dowels into the larger holes in the end edges of each panel as shown. Also insert 1x Dowel into the hole in the centre of the plinths longer edge. 7. Fit the Top. 2. Prepare the Right & Left hand Sides. You need: 4x Cams and a Screwdriver. You need: 4x Dowels, 4x Cam Pins and a Screwdriver. Carefully stand the assembly upright ensuring that all is supported to prevent damage. NOTE: Standing the assembly upright will require at least two people. PLEASE DO NOT ATTEMPT THIS ON YOUR OWN. Carefully lower the Top onto the Assembly ensuring that all Cam Pins, Dowels and Back Panels are correctly engaged into each of their corresponding holes and grooves. Once engaged, tighten the Cams in the Sides clockwise to secure the Top. 5 6 Lay the Right and Left hand Sides down on a flat soft surface with the holes and grooves facing upwards. Insert 2x Dowels into the large holes in the top end edges of each panel as shown. Using a Screwdriver fit 2x Cam Pins into the two smaller inner holes on the face of each panel as shown. 3 3. Attach the Plinth to the Base. 5. Fit the Back Panels. Fit the Plinth to the Base by inserting the exposed end of the central Dowel of the Plinth into the corresponding central hole on the underside of the Base panel. Note: As the Base and Plinth are only joined by one Dowel at this point, both components must be supported when being lifted. Fit the first Back Panel into the grooves on the Side and top face of the Base ensuring that the best face of the panel (the side that will be visible) is facing inwards. Once the panel is fully engaged into the groove, fit the Back Panel Divider onto the exposed top edge of the Back Panel. 4. Attach the Base & Plinth to one Side. You need: 2x Cams and a Screwdriver. Lay one Side down on a flat soft surface with the holes and grooves facing upwards. Lower the Base and plinth sub-assembly onto the Side, inserting the exposed heads of the Cam Pins and Dowels into their corresponding holes. Ensure both intersecting parts are flush with each other and that the groove in the top of the Base is aligned with the groove in the Side. Once all is aligned, fit 2x Cams into the large holes in the underside of the Base. Arrows on Cams must be pointing towards the Cam pins when being inserted. Once in position, turn each Cam clockwise until you feel resistance to secure the parts together. 4 Fit the remaining Back Panel (Best face inwards) by locating the edges into the grooves on the Side and Back Panel Divider. 5