Product Instructions for: 13PW146RCO CONSOLE TABLE For assistance with assembly or questions contact: Wayfair Customer Service, 877-WAYFAIR (877-929-3247) | www.wayfair.com PAGE 1 13PW146RCO CONSOLE TABLE Before beginning assembly, separate all parts and carefully study the parts diagrams below. Review all parts and hardware before disposing of any packaging. You may receive extra hardware with your unit. Call Customer Service for missing hardware. Parts List A: Top Frame (1) B: Shelf (1) C: Back Panel (1) D: Bottom Panel (1) E: Post (2) 1: Flat Washer (6) 2: Spring Washer (6) 3: Bolt 1/4” * 1-7/8”L (6) 4: Allen Wrench (1) 5: Cam Bolt (5) 6: Cam Lock (5) 7: Plastic Cover (5) 8: Wood Dowel (7) 9:Bracket (4) 10: Screw For Bracket 1/8” x 5/8”L (4) 11: Screw For Wall 9/32” x 1-1/2”L (4) 12: Plastic Strap (2) 13: Plastic Anchor (4) For assistance with assembly or questions contact: Wayfair Customer Service, 877-WAYFAIR (877-929-3247) | www.wayfair.com PAGE 2 13PW146RCO CONSOLE TABLE Assembly Instructions Step 1 Insert Cam Locks (6) into pre-drilled holes on Shelf (B). Screw Cam Bolts (5) into pre-drilled holes of Posts (E) and Back Panel (C). Attach Shelf (B) to Back Panel (C) and Posts (E), by inserting Wood Dowels (8) and Cam Bolts (5) into corresponding pre-drilled holes until Shelf (B) meets Posts (E) and Back Panel (C). Tighten by rotating Cam Locks (6) clockwise with Phillips screwdriver (not included). Cover cam lock holes with Plastic Covers (7). Figure 1 Step 2 Insert Cam Locks (6) into pre-drilled holes on preassembled unit from Figure 1. Screw Cam Bolts (5) into pre-drilled holes on Bottom Panel (D). Attach preassembled unit from Figure 1 to Bottom Panel (D) by inserting Wood Dowels (8) and Cam Bolts (5) into corresponding pre-drilled holes until preassembled unit from Figure 1 and Bottom Panel (D) meet. Tighten by rotating Cam Locks (6) clockwise with Phillips screwdriver. Insert Bolts (3) through Spring Washers (2) and Flat Washers (1) to connect Bottom Panel (D) to Posts (E) using pre-drilled holes, then tighten Bolts (3) with Allen Wrench (4). Cover cam lock holes with Plastic Covers (7). Figure 2 For assistance with assembly or questions contact: Wayfair Customer Service, 877-WAYFAIR (877-929-3247) | www.wayfair.com PAGE 3 13PW146RCO CONSOLE TABLE Assembly Instructions Step 3 Attach Top Frame (A) to preassembled unit from Figure 2 by inserting Wood Dowels (8) into corresponding pre-drilled holes until Top Frame (A) and preassembled unit from Figure 2 meet. Insert Bolts (3) through Spring Washers (2) and Flat Washers (1) to connect preassembled unit from Figure 2 to Top Frame (A) using pre-drilled holes, then tighten Bolts (3) with Allen Wrench (4). Figure 3 Step 4 Use Screws (10) to connect Brackets (9) to the back of Top Frame (A) as shown. Tighten Screws (10) with Phillips screwdriver. Drill 3/16” pilot holes in near proximity of Brackets (9) attached to the back of Top Frame (A). Tap the Plastic Anchors (13) into pilot holes in the wall. Use Screws (11) to connect Brackets (9) to the Plastic Anchors (13) on the wall. Tighten Screws (11) with Phillips screwdriver. Move this item close to the wall Brackets (9) and tie in both Brackets (9) with Plastic Strap (12) as shown in diagram. Figure 4 Now your Console Table is ready to use! For assistance with assembly or questions contact: Wayfair Customer Service, 877-WAYFAIR (877-929-3247) | www.wayfair.com PAGE 4
© Copyright 2024