1. No category

AE140A Sequential Controller
Operation Manual
Ⅰ.Panel and Terminal Diagram
Ⅳ.Description of Running
COM AC25 AC24 AC23 AC22 AC21
J2
Upper Display
Function
~
Time to next purge
AC26
AC27
6
6
AC28
COM
Function
Lower Display
AC20
AC29
AC19
~ nn
6
AC30
AC18
COM
S
Next solenoid number
AC17
AC16
7
8
AC31
AC32
6
AC33
COM
AC15
6
AC14
Ⅴ.Description of Panel Setting
AC34
AC13
AC35
Upper Display
FlneTek
AC12
Function
Range (Time error)
COM
11 10
AC36
Purge time
AC11
9
6
AC38
COM
AC39
AC10
AC40
AC09
COM
AC08
Auto-Shut-Off cleaning
6
...
AC07
5
AC06
R.C A
Number of solenoid
Lower Display
1
AC05
FAN.A
AC2
Range
~
Number of solenoid
ports
AC04
6
3
Function
~ nn
COM
4
~
SA5mS
~
SA0.1S
~
times
~ nn
Purge period
AC37
AC03
AC02
AC1
AC01
220V
110V
2
JS1
Solenoid
valve
220V
Ⅵ.Panel Setting Flowchart
110V
Running
Mode
Ⅱ.Terminal Description
1 Power supply: (AC1, AC2)
The Controller is able to select AC110V or 220V,-10%,+20%
50/60Hz
2 Power supply selection: (JS1)
X.X X
X.X X
X.X X
X.X X
X.X X
XXX
XXX
XXX
XXX
XXX
XXX
XXX
XXX
XXX
XXX
XXX
XXX
XXX
XXX
XXX
Please select the power supply AC 110V or 220V。
3 Power switch
4 Fan control input: (FAN.A)
This function is used to complete Auto-Shutdown cleaning
cycle before controller stopped. When this contact is
closed, controller running regulary. When this contact is
open, controller will run Auto-Shutdown cleaning cycle
(defined by "CLC" setting). This function is purposed to
prevent dust clogged on the bag.
Example: To set
5 Remote control input: (R.C.A)
If remote control is required, please remove the short
circuit, then, extend the wiring to remote site. When the
remote input is open circuit, the controller will stop
operation, when the remote input closed circuit, the
controller resumes normal working operation.
6 Solenoid terminals:
Terminals are connected to solenoids.
Ⅲ.Operation Panel:
7 Upper Display
9 ENTER
(SW1)
8 Lower Display
10 SHIFT
(SW2)
11 INCREASE
(SW3)
Purge time: 1 sec.
Purge period: 10 sec.
Auto-Shutdown cleaning: 2 times
Number of solenoid: 15 ports
Follow the steps below:
1 Press
into
purge time setting.
2 Press to make "X.X X" blink
(Possible to change value at this setting mode)
3 Press
,
to change the value till 1.00
4 Press
so that "1.00" doesn't blinking,
setting is done.
into
purge period, repeat step 2~4 to change
5 Then press
the value till 010.
.
into
clean up cycle setting, repeat step 2~4
6 Then press
to change the value till 002.
7 Then press
into
solenoid number setting, repeat step
2~4 to change the value till 015.
FineTek Co.,Ltd.
No.16, Tzuchiang St., Tucheng Industrial Park, New Taipei City 23678, Taiwan.
Tel : 886-2-22696789 Fax: 886-2-22686682
Email: [email protected] http://www.fine-tek.com
08-AE140A-B1-EM,08/01/2012