NEW PRODUCT 1 - Gregg Distributors
GREGG DISTRIBUTORS LTD. NEW PRODUCT SUPPLEMENT CATALOGUE In this issue: 3M Industrial Use Negative Pressure Respirators.....................................SP01-31 AVMOR® Carpet Care...............................................................................SP01-26 AVMOR® Cleaning Products......................................................................SP01-28 AVMOR® Disinfectant Cleaners.................................................................SP01-27 AVMOR® Dispensers..............................................................SP01-28 to SP01-29 AVMOR® Floor Care..................................................................................SP01-26 AVMOR® Foodservice Care.......................................................................SP01-27 AVMOR® Washroom Care.........................................................................SP01-26 BEHRINGER Pipe Clamps.....................................................SP01-34 to SP01-35 BOSCH Diagnostic Equipment..................................................................SP01-24 BUSINESS/OFFICE SUPPLIES 3M Post-it® Tape...................................SP01-23 CASTROL® Motor Oils, Lubricants, & Fluids............................................SP01-30 CAT® CLOTHING Fleece Jacket...............................................................SP01-31 CAT® FOOTWEAR Industrial Footwear.....................................................SP01-31 CHAPIN® Industrial Sprayers....................................................................SP01-51 CROSBY Fittings.......................................................................................SP01-38 CROSBY Hoist Rings................................................................................SP01-38 DYNALINE Hardware & Automotive Products...........................................SP01-24 FLUKE Accessories................................................................SP01-50 to SP01-51 FLUKE Clamp Meters................................................................................SP01-41 FLUKE Digital Multimeters.....................................................SP01-39 to SP01-41 FLUKE Indoor Air Quality Tools.................................................................SP01-49 FLUKE Power Quality Tools & Power Analyzers....................SP01-43 to SP01-44 FLUKE Laser Distance Meters..................................................................SP01-47 FLUKE Test Tools - Fluke Connect Wireless System.....................................................................SP01-48 to SP01-49 FLUKE Thermal Imagers........................................................SP01-47 to SP01-48 FLUKE Thermometers............................................................SP01-45 to SP01-47 FLUKE True-RMS Clamp Meters..............................................................SP01-41 FLUKE True-RMS Digital Multimeters.......................................................SP01-39 FLUKE Testers.......................................................................SP01-42 to SP01-43 FLUKE Vibration Meters.........................................................SP01-44 to SP01-45 GROTE Trailer Connectors.......................................................................SP01-33 KNAACK JUNK TRUNK Jobsite Chest.....................................................SP01-09 1 2015 LOCTITE® Retaining Compounds.............................................................SP01-30 MAKITA Outdoor Power Equipment....................................... SP01-11 to SP01-13 MAKITA Power Tools.............................................................. SP01-10 to SP01-11 MALLORY® Snowbrush.............................................................................SP01-30 MARSHALLTOWN Concrete Tools.........................................SP01-04 to SP01-06 MARSHALLTOWN Drywall Tools...........................................SP01-06 to SP01-08 MARSHALLTOWN Flooring Tools..........................................SP01-08 to SP01-09 MARSHALLTOWN Masonry Tools.........................................SP01-02 to SP01-03 MR. HEATER® Forced Air Propane Heaters.............................................SP01-13 NORTON Core Bits...................................................................................SP01-23 NORTON Diamond Tools and Accessories............................SP01-14 to SP01-19 NORTON High Speed Diamond Blades....................................................SP01-20 NORTON Masonry Diamond Blades.........................................................SP01-20 NORTON Portable Hand-Held Diamond Blades.......................................SP01-22 NORTON Portable Hand-Held Diamond Cup Grinders.............................SP01-22 NORTON Silencio Diamond Blades..........................................................SP01-23 NORTON Tile Diamond Blades.................................................................SP01-21 NORTON Walk Behind Diamond Blades...................................................SP01-21 PIONEER® Winter Hard Hat Liners...........................................................SP01-30 PIRIT® Heated Hose..................................................................................SP01-32 PREDATOR™ High Tension Clamps........................................................SP01-32 PRIORITY® Cylinder Storage Cabinets.....................................................SP01-25 PRISTINE™ Tilt Trucks.............................................................................SP01-29 PRONGHORN™ Electrical Products........................................................SP01-25 PROPEL™ HD Cranes & Engine Stands..................................................SP01-37 PROPEL™ HD Jacks.............................................................SP01-35 to SP01-37 PROPEL™ HD Miscellaneous Equipment................................................SP01-38 PROPEL™ HD Portable Hydraulic Equipment..........................................SP01-37 PROPEL™ HD Shop Presses...................................................................SP01-38 SLIP-N-GRIP® Car Accessories................................................................SP01-51 WHITEBOARDS Single-Sided..................................................................SP01-23 MARSHALLTOWN MST/2750 Masonry Tools PHILADELPHIA STYLE TROWEL Philadelphia pattern trowels are better suited for laying block because they allow for more mortar to be placed on the blade. •Forged from a single piece of high carbon steel, then heat treated for strength and durability •Blade is taper ground and polished •Handle rise is set for the correct hang and balance •Impact area is extra strong •Resilient DuraSoft® handle with integral finger guard Part No. 199.5FG, 9½” x 4¾”. Part No. 1910.5FG, 10½” x 5¼”. Part No. 1911FG, 11” x 5½”. PHILADELPHIA STYLE POINTING TROWELS Philadelphia pattern trowels are better suited for laying block because they allow for more mortar to be placed on the blade. •Forged from a single piece of high carbon steel for unsurpassed strength •Resilient DuraSoft® handle with integral finger guard Part No. 455D, 5” x 2½”. Part No. 456D, 6” x 2¾”. LONDON STYLE TROWEL London pattern trowels are the standard blade type for laying brick. •Forged from a single piece of high carbon steel, then heat treated for strength and durability •Handle rise is set for the correct hang and balance •Blade is taper ground and polished •Impact area is stronger •Resilient DuraSoft® handle with integral finger guard Part No. 339FG, 9” x 4¼”. Part No. 3310FG, 10” x 4-5/8”. Part No. 3311FG, 11” x 4-7/8”. MARGIN TROWELS GAUGING TROWEL INSULATOR’S TROWEL MAGNESIUM HAWKS ALUMINUM HAWKS TUCK POINTERS BRICK JOINTERS JOINT RAKER GROUT BAG DISPOSABLE GROUT BAG Guarded Mason’s Chisel BRICK TONGS •Forged from a single piece of high carbon steel •Tempered, ground and polished from toe to heel •Resilient DuraSoft® handle with integral finger guard Part No. 52D, 5” x 2”. Part No. 54D, 5” x 1½”. •Made of heavy gauge, hard-rolled aluminum •Edges have been smoothed and the corners rounded •Callus preventer and handle included •Wood handle Part No. 1W, 13” x 13”. •Made of seamless black vinyl Part No. GB691, 12” x 24”. SP01-2 •Forged from a single piece of high carbon steel •Carefully taper ground and polished •Many uses, including mixing or “gauging” small quantities of mortar or quick setting plaster •Resilient DuraSoft® handle with integral finger guard Part No. 48D, 7” x 3-3/8”. •Forged from one piece of high carbon steel •Tapered for the required sturdiness and correct flexibility •High shank and high lift give plenty of hand room •Resilient DuraSoft® handle with integral finger guard Part No. 502D, 6½” x 3/16”. Part No. 503D, 6½” x 1/4”. Part No. 504D, 6¾” x 5/16”. Part No. 505D, 6¾” x 3/8”. •Great for hard to clean materials •Trim tip to desired opening •Thermally sealed edge and tip to prevent leaks •Box of 50. Part No. DGB661, 11” x 21”. GREGG DISTRIBUTORS LTD. •Forged from a single piece of the highest grade tool steel •Tempered, ground and polished •Flexible blade is ideal for working with insulation •Resilient DuraSoft® handle with integral finger guard Part No. 48AD, 7” x 3-3/8”. •Made from high carbon steel •Each end is a different joint size •10½” length Part No. 83, 3/8” and 1/2”. Part No. 80, 1/2” and 5/8”. Part No. 82, 5/8” and 3/4”. Part No. 81, 3/4” and 7/8”. • Plastic guard protects hand and prevents slippage down the chisel •Forged from the finest quality tool steel, hardened, tempered and well-balanced Part No. 604B26SG, 7”L x 4”W. •Made of lightweight durable magnesium •Score marks are machined to a uniform depth and specially shaped to help the blade remain flat •Callus preventer and handle included •DuraSoft® handle Part No. 5206D, 13” x 13”. •Large 1¾” skate wheels •Strong aluminum handle is contoured to fit the hand and squared off at the end •Hardened nail, adjusts to proper depth Part No. 89, 8½” x 3” size. •Heavy-duty design, built for long wear, maintenance free •Can be quickly adjusted to carry from six to ten bricks Part No. 88, 16” to 26½” size. MARSHALLTOWN MST/2750 Masonry Tools RUB BRICK •Ideal for dressing down and removing marks from concrete or cleaning brick •20 grit •Fluted, comes with handle Part No. 841, 8” x 3½” x 1½”. GATORBACK® MORTAR BOARD •Water resistant, contour surface is designed to keep mortar and stucco at optimal workability and consistency •Made of a lightweight, impact and UV resistant polymer that won’t conduct heat and is nearly indestructible •Reinforced integrated handle for easy transportation •Reinforced ribbing enables Gatorback® mortarboards to hold up to 150 lbs of material with little flex Part No. GBK0306, 24” x 24”. BRAIDED NYLON MASON’S LINE •Size #18 •6” core •Will not unravel if struck by a trowel •Not affected by extreme moisture or dryness •Won’t mildew and stays taut Part No. Description 622M ML605 ML606 631M ML607 632M 623M 624M 626 ML340M ML339M ML338 ML341 625 628 627 ML609 ML610 ML611 ML612 250 ft. (76M) White 250 ft. (76M) Yellow 250 ft. (76M) Green 250 ft. (76M) Fl. Pink 250 ft. (76M) Fl. Orange 250 ft. (76M) Fl. Yellow 500 ft. (152M) White 500 ft. (152M) Yellow 500 ft. (152M) Green 500 ft. (152M) Fl. Pink 500 ft. (152M) Fl. Yellow 500 ft. (152M) Fl. Orange 500 ft. (152M) Fl. Green 1000 ft. (305M) White 1000 ft. (305M) Yellow 1000 ft. (305M) Green 1000 ft. (305M) Fl. Pink 1000 ft. (305M) Fl. Orange 1000 ft. (305M) Fl. Green 1000 ft. (305M) Fl. Yellow MASON’S LINE WINDER •Plastic winder •#18 braided orange mason’s line •Handle is tapered Part No. 634, 250 ft. (76M) Orange HEAVY DUTY RUBBER PAILS •Heavy duty rubber-will not rust, dent, leak or chip •Bounce back upon impact •Resist heat and cold, lime, acids, salt, water, fuels, grease and chemicals Part No. DF12, 12 qt. pail with standard lip. Part No. DFP18, 18 qt. pail with pouring lip. TWISTED NYLON MASON’S LINE Part No. Description •Bristles made of white Tampico fiber •3½” (89 mm) bristles are set securely in hardwood block Part No. 829, 6½” X 1¾” size. •Used to hold line and maintain straightness during brick/block laying •Made of steel •Pack of 14 Part No. 16509. •Winder can be driven into the ground to allow for hands free use •Made of durable highdensity polyethylene •Can be refilled with any length or type of mason’s line that is wound onto a 6” core • 500 ft. (152M) Part No. SLW66FO, #18 twisted mason’s line, Orange. Part No. SLW66FY, #18 braided mason’s line, Yellow. 285 ft. (87M) White 285 ft. (87M) Yellow 285 ft. (87M) Fl. Yellow 500 ft. (152M) White 500 ft. (152M) Yellow 500 ft. (152M) Fl. Pink 500 ft. (152M) Fl. Orange 500 ft. (152M) Fl. Green 500 ft. (152M) Fl. Yellow 1000 ft. (305M) White 1000 ft. (305M) Yellow 1000 ft. (305M) Fl. Pink 1000 ft. (305M) Fl. Orange 1000 ft. (305M) Fl. Green 1000 ft. (305M) Fl. Yellow MASONRY BRUSH LINE PINS WOOD LINE BLOCKS •Shaped from poplar hardwood •Sold in pairs Part No. 86, 3¾” size. •Made of tempered zinc plated steel for increased durability •Tapered ends allow easier insertion •4 line pins per bag •4¼” long Part No. 11735. •Made of extra high density, UV stabilized polyethylene •Durable, lightweight and easy to clean •Dry mortar will not stick •Not affected by heat and cold, rust, plaster, mortar and water •10 cubic foot (.28 cubic meter) capacity Part No. 11165, 60” x 32” x 11”. REFILLABLE STAKE MASON’S LINE WINDERS •Size #18 •6” core •”Heat-set” after winding to stabilize •Not affected by mortar, oil, or mildew and will not absorb water 620 621 ML577 ML578 ML579 ML581 ML582 ML583 ML584 629 ML585 ML587 ML588 ML589 ML590 LINE TWIGS MORTAR BOX PLASTIC LINE BLOCKS •Bright yellow plastic is highly visible and impervious to water •Twigs keep mason’s line from sagging •Included are 4 plastic line twigs, 2 pair of blocks Part No. 86P, 5” X 2¼”. FLOOR SCRAPERS •60 X 1-1/8” steel handle securely welded to heavy angle iron bracket •Blade is heavy gauge spring steel •Plastic grip on handle to protect hands •This durable scraper is perfect clean-up tool Part No. 420, 9” x 4½”. Part No. 420B, Blade for #420. Part No. 720, 14” x 4½”. Part No. 720B, Blade for #720. Part No. 820, 20” x 4½”. Part No. 820B, Blade for #820. www.greggdistributors.ca SP01-3 MARSHALLTOWN MST/2751 Concrete Tools HIGH CARBON STEEL FINISHING TROWELS •Highest grade hardened and tempered spring steel blade, properly shaped •Aluminum alloy Xtralite® mounting is lightweight but very strong •Beveled work edges prevent surface aggregate popping •Resilient DuraSoft® handle provides a soft feel, reduces fatigue and offers excellent durability Part No. MXS56D, 12” x 3”. Part No. MXS62D, 12” x 4”. Part No. MXS64D, 14” x 4”. Part No. MXS66D, 16” x 4”. Part No. MXS81D, 18” x 4”. Part No. MXS20D, 20” x 4”. HIGH CARBON STEEL POOL TROWELS •Highest grade hardened and tempered spring steel blade, properly shaped •Short aluminum alloy Xtralite® mounting is lightweight but very strong •Blade is flexible enough to conform to almost any radius •DuraSoft® handle Part No. SP10SD,10” x 3”. Part No. SP14SD, 14” x 4”. Part No. SP16SD, 16” x 4½”. MIDGET TROWEL •Aluminum alloy Xtralite® mounting is lightweight but very strong •DuraSoft® handle Part No. 11D, 8” x 3”. FINISHING TROWEL HANDLE •Curved DuraSoft® handle Part No. 402D, 1-9/16” dia. HEAVY DUTY ZINC HAND EDGER STRAIGHT END HAND EDGERS •Made from high quality, long wearing zinc •Resilient DuraSoft® handle provides a soft feel, reduces fatigue, and offers excellent durability •Smooth finish allows for easier clean-up •Longer lasting and heavier than steel edgers Part No. 4002D, 9” x 4”. •Resilient DuraSoft® handle provides a soft feel, reduces fatigue and offers excellent durability •Used to produce a radius at the edge of a concrete slab to help prevent the edge from chipping Part No. 36D, 6” x 3” carbon steel blade. Part No. 160SSD, 6” x 4” stainless steel blade. CURVED END HAND EDGERS HEAVY DUTY ZINC HAND GROOVERS WOOD HAND FLOATS SIDEWALK SLICKER FLOAT CAST MAGNESIUM HAND FLOAT BEVELED END MAGNESIUM HAND FLOATS ROUND END MAGNESIUM HAND FLOAT FLOAT HANDLE •Both ends are curved up for use in either direction •Resilient DuraSoft® handle provides a soft feel, reduces fatigue and offers excellent durability •Used to produce a radius at the edge of a concrete slab to help prevent the edge from chipping •Curved ends help prevent edger from digging into wet concrete Part No. 136D, 6” x 3” carbon steel blade. Part No. 136SSD, 6” x 3” stainless steel blade. Part No. 156SSD, 6” x 4” stainless steel blade. •Cast from the finest magnesium •Designed with just the right broken-in shape •Cast construction allows more knuckle clearance •Placement of the handle gives the float perfect balance Part No. 148D, 16” x 3-1/8”. SP01-4 •Made from high quality, long wearing zinc •Resilient DuraSoft® handle provides a soft feel, reduces fatigue and offers excellent durability •Smooth finish allows for easier cleanup •Finely finished to cut sharp clean grooves •6” x 4-3/8” Part No. 833D, 1/2” Depth. Part No. 834D, 3/4” Depth. Part No. 835D, 1” Depth. •Extruded from very hard, durable, lightweight magnesium •Our most popular float design •Comfortable handle is positioned to give the tool perfect balance •Recommended for use with air entrained concrete •Magnesium floats produce a smoother finish than wood Part No. 142D, 12” x 3-1/8”. Part No. 145D, 16” x 3-1/8”. Part No. 146D, 20” x 3-1/8”. GREGG DISTRIBUTORS LTD. •Made from clear, seasoned redwood, 3/4” thick •Primarily used for leveling and smoothing concrete prior to final finish •Also ideal when a slightly rougher concrete finish is desired Part No. 44D, 12” x 5”. Part No. 144D, 16” x 3½”. •Extruded from very hard, durable, lightweight magnesium •Fully rounded ends help prevent float marks •Comfortable handle is positioned to give the tool perfect balance •Magnesium floats produce a smoother finish than wood •Handles are secured with torque pad screws that will not back out Part No. 143D, 16” x 3-1/8”. •The same lightweight, durable extrusion as our magnesium floats •Moves easily around obstacles and easily accesses hard to reach places •Comes with 360˚ EZ Twist Bracket •Requires threaded or snap adapter (sold separately) Part No. RED700228, 24” x 3½”. Part No. RED700229, 36” x 3½”. •Fit all of our magnesium hand floats Part No. 16D, 9” x 1¼” DuraSoft®. MARSHALLTOWN MST/2751 Concrete Tools MAGNESIUM BULL FLOATS FRESNO TROWEL •Made from the finest extruded magnesium available •Lightweight, long wearing and properly balanced to provide the finish you want •No other heavy duty bull float outlasts this one Part No. B36, Square End, 36” x 8”. Part No. B36FR, Round End, 36” x 8”. Part No. B48, Square End, 48” x 8”. Part No. B48FR, Round End, 48” x 8”. •Superior quality high carbon steel blade •Round ends leave less drag marks •All-angle swivel attachment included Part No. C36R, Round, 36” x 5”. PUSH BUTTON ADAPTERS ROCK-IT™ 2.0 •Fit 1-3/8” and 1¾” push button handles •Use with bull floats, fresnos, brooms, etc. Part No. 4818, Clevis End. Part No. 4819, Male Thread. Part No. 4822, Bull Float Adapter. •Allows multi-angle floating •Enables use with extension handles for extremely long ranges •Full pitch controlled by half turn of handle •Fits all magnesium bull floats without adapter plates •Fits all push button handles - 1-3/8” and 1¾” without any additional adapters Part No. BF9. ALUMINUM THREADED HANDLE SECTION PUSH BUTTON HANDLE SECTIONS 360˚ TWIST BRACKETS BULL FLOAT REPLACEMENT PARTS •Lightweight aluminum •The large threads can be combined with similar handles Part No. B572, 72” length, 1¾” dia. •Compatible with bull floats, groovers, edgers, fresnos, brooms and more •Allows quick, easy adjustments on the job •0° to 90° handle-angle adjustment and full 360° rotation of finishing tool Part No. 360PBA134, Push Button Adapter. Part No. 360THREAD, Threaded Handle Adapter. •Anodized spring loaded button-type aluminum sections snap together quickly and will not loosen during use Part No. PB72, 72” length, 1-3/8” dia. Part No. PB72L, 72” length, 1¾” dia. •Fits most four hole bull floats Part No. A3001, Handle Socket. Part No. A3002, Bracket Base. Part No. A3003, Threaded Complete Assembly. A3001 A3002 A3003 FRESNO TROWEL ADAPTERS ALL ALUMINUM PLACERS •Aluminum construction, powder coated with soft grip end-cap •Braced for additional •Aluminum casting •Designed specifically to connect standard threaded handle sections to strength •60” long a fresno, walking edger or groover or any other Part No. AP753, Placer without Hook. tools that are equipped with similar attachment Part No. AP753H, Placer with Hook. devices •Unique “wrench-flats” feature for easy removal Part No. 3748. ALUMINUM ALLOY SCREEDS SCREED HANDLES •Premium high strength aluminum alloy won’t rust or rot, warp resistant •End capped to prevent concrete from getting inside •Lightweight, long wearing and rigid •H-style design for added strength Part No. 14770, 8 ft. x 1½” x 3½”. Part No. 14771, 10 ft. x 1½” x 3½”. Part No. 14772, 12 ft. x 1½” x 3½” WOOD BACKED CONCRETE BROOM ADAPTERS DUST PANS •#6515 has an all-angle center mount •Cut out •Black baked enamel finish is durable with BROOMS •Long wearing 3” black polypropylene bristles set solidly into a natural lacquered hardwood block •Threaded hole accepts any standard broom handle •Ideal for applying non-slip finish to newly finished concrete surfaces Part No. 830, 24” length. Part No. 847, 36” length. Part No. 848, 48” length. section of adapter fits over broom bracket and accepts broom thread handle •#6516 mounts to most broom heads and accepts the #6515 allowing broom heads to be used with different handles Part No. 6515, Threaded Handle Clevis Adapter. Part No. 6516, Clevis Adapter Base Bracket. beveled edge •Corrugated ribs add to strength •Made of heavy 20-gauge steel Part No. DP12, 12” length. Part No. DP16, 16” length. •Attach to each end of screed board for sawing applications •Comfortable soft grip handles •Sold as a set of 4 handles, with mounting hardware and template Part No. 10665. KNEELER BOARD •Extra large handle grips •Offers extracomfortable support for knees •Black foam pad securely fastened to generously sized polypropylene tray Part No. KB451, 19” x 13½”. www.greggdistributors.ca SP01-5 MARSHALLTOWN MST/2751/2752/2753 Concrete Tools REBAR BENDER •Bends rebar up to #5 ( 5/8” rebar) grade 60 Part No. 14739, 34” length. PULL TIE WIRE TWISTER TIE WIRE REELS TIE WIRE TWISTERS MAGNESIUM ASPHALT RAKE BRACED MAGNESIUM LUTE RAKES U SHAPED PUSH CRACK SQUEEGEE 16” WIRE STREET BROOM HEAD ASPHALT RAKE BROAD KNIVES PERMASHAPE® “FLAT” TROWEL •Safely and easily twists looped wire bar ties •Rubber grip handle •Twists most ties with a single pull Part No. 12637, 12” length. •Fits any standard size belt •Accomodates all types of tie wire Part No. TWR19, Constructed of lightweight aluminum. Part No. TWR26, Made of lightweight durable plastic. •Compact size allows the tool to be used in tight spaces •Safely and easily twists looped wire bar ties •Durable design Part No. 14731, Standard. Part No. 14171, Heavy-Duty. Asphalt Tools POUR POTS •Durable, 14 gauge welded steel construction •Fingertip nozzle control •Adjustable pouring nozzle from 1/2” down to 3/8” •Used to apply cold crack sealants •2.6 gallon capacity Part No. RED704988W, Pour Pot with Wheels. Part No. RED704989, Pour Pot with Long Handle. •Lightweight “T” section blade has blunt teeth which are designed to allow material to pass through without catching •Rugged formed steel pole connector prevents breakage and ensures rigidity Part No. 838, 36” Lute Head. Part No. 839, 72” Handle Only. V SHAPED CRACK SQUEEGEE •Unique V shape design allows you to push or pull material into cracks •Forces sealant down into crack while pushing excess material forward •Black neoprene blade has a temperature rating of 170°C •Comes complete with a 54” clevis style wood handle •Use with crack pour pot Part No. RED704942, Squeegee. Part No. RED704943, Replacement Black Neoprene Blade. •Durable lightweight magnesium head •Combination lute rake •Aluminum handle •All parts are easily replaceable •Comes with 7 ft. handle •3” x 36” rake Part No. RED700092, Blunt blade. Part No. RED700102, Sharp blade. Part No. RED700112, Plain blade. •Coated steel wire •Built strong to withstand heavy duty cleaning of driveways and parking lots •3¾” bristles Part No. RED704152. •Comes complete with a 54” wood handle •Black neoprene blade •U shaped cavity leaves a wider path of sealant •Use with crack pour pot Part No. RED700996, Squeegee. Part No. RED714193, Replacement Black Neoprene Blade. •14 teeth 3¾” long •15½” level head •60” lacquered ash handle Part No. RED802921. Drywall Tools DURASOFT® STAINLESS STEEL TAPING KNIVES •Tempered premium stainless steel blade with aluminum backing plate •Tapered blade flexes just right for feathering but won’t take a set •Resilient DuraSoft® handle provides a soft feel, reduces fatigue and offers excellent durability Part No. 3506SD, 6” x 3”. Part No. 3508SD, 8” x 3”. Part No. 3510SD, 10” x 3”. Part No. 3512SD, 12” x 3”. Part No. 3514SD, 14” x 3”. SP01-6 DURASOFT® BLUE STEEL TAPING KNIVES •Premium tempered blue steel blade with aluminum backing plate •Blade is tapered so you can run corners faster and easier •Blade flexes just right for feathering but won’t take a set •Resilient DuraSoft® handle provides a soft feel, reduces fatigue and offers excellent durability Part No. 3506D, 6” x 3”. Part No. 3508D, 8” x 3”. Part No. 3510D, 10” x 3”. Part No. 3512D, 12” x 3”. Part No. 3514D, 14” x 3”. GREGG DISTRIBUTORS LTD. •Blue spring steel blade •Lightweight aluminum handle •Used for taping and seaming joints •Rubber handle cap with hanger •More flexible than a taping knife Part No. BK386, 9” x 17-7/8”. Part No. BK388, 9” x 28”. •Guaranteed to stay flat use after use •Made from highest grade stainless steel •Properly shaped and tempered to a golden finish •Withstands pressure of hard-troweling •Flat blade makes applications easier with more consistent finish •Smooth, natural finish hardwood handle Part No. 165GSFP, 16” x 5”. MARSHALLTOWN MST/2750/2751/2753 Drywall Tools DURAFLEX TROWELS •PermaShape® guarantees trowel will maintain original flat shape •Flat, yet flexible blade makes applications easier with more consistent finish •Highest grade hardened and tempered golden stainless steel blade, properly shaped and fastened with stainless steel rivets •Withstands pressure of hard-troweling •9¾” mounting Part No. 4663DFDL, 12” x 5”. Part No. 4681DFDL, 13” x 5”. METAL MUD PAN •Made from stainless steel •Tapered ends and sides with mud-tight seams •Sides are sheared to clean knives easily Part No. 812. Top Length: 14” Bottom Length: 12½” Top Width: 4-5/8” Bottom Width: 3” Height: 3-5/8” HAWK HANDLES •DuraSoft® handle •Comes with a bolt for secure fastening Part No. 412D. THIN COAT INSIDE CORNER TROWEL OUTSIDE CORNER TROWEL PLASTIC MUD PAN ALUMINUM HAWKS •Lightweight tool made from one piece of flexible stainless steel •Has a 90° angle between the blades •Resilient DuraSoft® handle with integral finger guard •Used to embed tape and smooth out the final layer of mud to taped corners Part No. 24D, 5” x 3¾”. •Made of long wearing plastic with hang-up tab •Equipped with two metal wiping blades •Resists chemicals and temperature changes •Outside is slightly textured to provide a nonslip surface Part No. 814. •Made of heavy gauge hard-rolled aluminum •Edges have been smoothed and the corners rounded •Has a threaded 3-5/8” flange •Handle and sponge rubber callus preventer included •DuraSoft® handle Part No. 1D, 13” x 13”. Top Length: 14-7/8” Bottom Length: 13¼” Top Width: 4¾” Bottom Width: 3” Height: 3¼” CALLUS PREVENTER EGGBEATER MIXER •Made of sponge rubber •Can be used with any hawk Part No. 0. • Welded all-steel construction; fully plated • 7/16’’ (11mm) steel hex shaft Part No. 897, 30” length. BUCKET DIPPERS PANEL LIFTER •Galvanized steel construction •Scoop mud directly on trowel or hawk •Soft grip handle for increased grip and less fatigue •Bucket hanging clip for less mess and easy storage Part No. BD862, 1 litre capacity. Part No. BD863, 0.6 litre capacity. •Lightweight tool made from one piece of flexible stainless steel •Blade set at an 80° angle that flexes during use to 90° to form a clean square outside corner •Resilient DuraSoft® handle with finger guard •Used to embed tape and smooth out the final layer of mud to taped corners Part No. 25D, 5” x 3¾”. • Non-slip checkered surface provides foot traction •Self-righting feature makes it ready for use without fumbling •Tapered front end slides easily under the board; then it lifts and holds it in place while nailing Part No. 790, 12” x 5¼”. QUICK-MIX MIXERS •Blade is securely welded to 3/8” hex shaft •Ideal for stirring and blending paint, drywall mud and acoustic quickly and lump free •Works with all 7/16” or larger and a limited number of 3/8” slow speed drills •Blade measures 8½” x 4½” Part No. 819, 28” length. PANEL LIFTER/RASP/ BOTTLE OPENER •Non-clogging rasp with protective guides •Lifts all standard sizes of drywall sheets •Lightweight, compact, fits in pocket •Bottle opener integrated into lifter Part No. PL589. www.greggdistributors.ca SP01-7 MARSHALLTOWN MST/2751/2753/2754 Drywall Tools DURASOFT® DRYWALL RASP DRYWALL SAW DRYWALL CIRCLE CUTTER RUBBER FLOATS •Hardened cutter wheel and center pin will remain sharp indefinitely •Cuts sharp clean circles up to 16” in diameter with only one hand •Measure accurately on the calibrated steel shaft Part No. CC766, 8½” length. •Has a 5/8” thick red rubber pad specially bonded to the aluminum backing plate for long wear •Frequently used by plasterers and other finishers for rough and/or textured finishes •9” x 4” Part No. 38, Fine. Part No. 39, Coarse. MOLDED RUBBER FLOAT DURASOFT® HAND SANDER WALL REPAIR PATCH KIT KNOCKDOWN KNIVES TILE GROUTER’S FLOAT TILE GROUTER’S MARGIN FLOAT •Removes 45% more material per stroke than other popular rasps •Will not clog or collect dust •Works in both directions •Long-lasting premium stainless steel blade •Contoured DuraSoft® handle ensures a good grip •Ends of blade get into tight spaces •Sharp blade has many other uses like backer board and vinyl tile Part No. DR390. •Molded black rubber pad is very compact and has a dense texture •Float face is permanently cemented to the lightweight aluminum backing •The ideal float for bringing sand to the surface Part No. 40, 9” x 4”. •Cuts quickly through wallboard, gypsum, lath and thin coat backing board •Hardened and tempered blade •Five teeth per inch Part No. DS921, 15” length. •Lightweight aluminum backing plate bonded to foam pad •Resilient DuraSoft® handle provides a soft feel and reduces fatigue •Designed for die-cut or a half sheet of standard sandpaper or sand screen Part No. 20D, 9-3/8” x 3¼”. •No-rust aluminum plate provides rigid backing •Self-adhesive patches •Fiberglass mesh eliminates the need to pre-plaster Part No. DP4, 4” x 4”. Part No. DP6, 6” x 6”. Part No. DP8, 8” x 8”. •Blades made of GE Lexan® •Threaded DuraSoft® handle with metal ferrule and hanging hole •Drying time reduced when used for texturing Part No. KD18, 18” length. Part No. KD24, 24” length. Flooring Tools STANDARD & NTCA APPROVED NOTCHED TROWELS •Aluminum alloy mounting riveted to a hard tempered steel blade •Choice DuraSoft® or hardwood handle •Blade size is 11” x 4½” Part No. 703SD, 3/16” x 1/8” x 3/16” Square notch. Part No. 702SD*, 1/4” x 1/4” x 1/4” Square notch. Part No. 5779SD, 3/8” x 3/8” x 3/8” Square notch. Part No. 704SD, 3/32” x 3/32” x 1/8” U notch. Part No. 718SD, 1/4” x 1/4” x 1/4” U notch. Part No. 701SD, 7/32” x 5/32” V notch. Part No. 779SD, 1/4” x 1/4” V notch. *NTCA Approved Trowels PLASTIC FOAM FLOATS •Plastic foam pad specially bonded to an aluminum backing plate •Wears well and does an excellent job on any sand surface •Pads are 3/4” thick Part No. 46G, Green/Fine, 9½” x 4”. Part No. 4417, Replacement Pad. SP01-8 TILE SETTER’S TROWEL •Forged from a single piece of high carbon steel •Blade is fully tempered, ground and polished •DuraSoft® handle Part No. 57D, 7” x 4-3/8”. GREGG DISTRIBUTORS LTD. •Pure gum rubber face is bonded to the dense rubber pad; cemented to an aluminum backing plate with a smooth handle •Edges are beveled and the two front corners are rounded •Dense rubber pad is designed specifically for tile grouting Part No. 43, 9” x 4”. CRESCENT® TILE NIPPERS •Has 5/8” offset jaws with carbide tips •Unique handle design for added comfort •Plastic grip •Handle stops to protect tips •Center spring returns jaws to open position Part No. GT28CN. •Pure gum rubber face is bonded to the dense rubber pad; cemented to a tempered steel blade with a soft grip handle •Edges are beveled •Dense rubber pad is designed specifically for tile grouting Part No. MF54, 6” x 2”. NOTCHED MARGIN TROWELS •Forged from a single piece of highest grade tool steel •Tempered, ground and polished from toe to heel •DuraSoft® handle •Blade size is 5” x 2’’ Part No. 52SND, 1/4 x 1/4 x 1/4 Square-Notch Size. Part No. 52VND, 1/4 x 3/16 V-Notch Size. MARSHALLTOWN MST/2753/2754 Flooring Tools “DELUXE BIG CLINKER” TILE CUTTER TILE FILE •Four position scoring height adjustment knob to allow scoring and cutting of tiles up to 3/4” thick •Cutter has 20 mm diameter dual chrome plated steel bars that are heat treated for longest life •Features a 4¾” wide breaker foot and a 12” wide protractor gauge •Makes 27½” straight cut and 19½” diagonal cut length Part No. JP700ST, “Deluxe Big Clinker”. Part No. 22X, Replacement Titanium Rotary Wheel. •Removes sharp and irregular edges from tile and marble •Tungsten carbide grit •Soft grip handle Part No. TILEFILE. GROUT SAW KNEE KICKER •Resilient DuraSoft® handle with finger guard •Die cast aluminum mounting with thumb rest •Blade coated with tungsten carbide Part No. 446. Part No. 15465, Replacement Blades. KNA/2605 T-HANDLED FLOOR SCRAPER •All steel heavy duty construction •54” long T-handle •Removes many types of floor coverings from a variety of floors •Ships with 7” blade Part No. THS7. Part No. THS7B, 7” Replacement Blade. DURASOFT UNDERCUT SAW ® •Extra thick knee pad for comfort •Non-slip hand grip •Adjusts from 17½” to 21½” •High contour neck Part No. CSKK Knee Kicker. Part No. PPACS Pin Plate Assembly. Part No. NGPCS Nap Grip Pads (3). Part No. BACS Bumper Assembly. Part No. KKSC Replacement Spring Clip. •Undercuts door jambs and other wall base obstacles •Specially shaped 12” long blade permits right or left hand cutting •DuraSoft® handle Part No. US9041. Part No. RB9041, Replacement blade. BUCKET HEATER •Designed to continuously heat buckets of water •1000 watt, 120 volt power will heat water over 150° •Ideal for use on cold winter days •Stainless steel guard Part No. 742G. KNAACK JUNK TRUNK Jobsite Chest First and only jobsite chest with independent locking drawer. Features: •JUNK TRUNK Quick Access Drawer - Heavy-duty independent locking drawer for quick access to high demand tools and accessories •Gas strut supported chest lid controls closing speed to prevent lid slamming, and locking hinge to keep chest lid open •Dual Watchman IV Lock System - Independent locking system for both the chest and JUNK TRUNK quick access drawer •Get your chest where you need it with standard 4-way skids adaptable for 6” wheel casters •Built Knaack tough for security against theft and weather with 16 gauge steel and anti-theft design •External Dimensions - Closed: 48” x 30” x 35”; Open: 48” x 52” x 62” •Internal Dimensions - Chest: 47” x 29” x 22”, 17 ft3; Drawer: 42” x 29” x 5”, 3.5 ft3 •Weight - 254 lbs. Part No. 4830-D. www.greggdistributors.ca SP01-9 MAKITA MAK/2704 Power Tools DRYWALL CUTOUT TOOL PORTABLE BAND SAW 4-3/8” MASONRY SAW SPECIFICATIONS Collet Capacities: 1/8” and 1/4” AMPS (120V): 5.0 A No Load Speed: 32,000 RPM Vibration Level: 2.5 m/s2 Noise Level: 82 dB(A) Overall Length: 9-7/8” Net Weight: 2.4 lbs SPECIFICATIONS Maximum Capacities: Round Work Piece Diameter: 4¾” Square Work Piece: 4¾” x 4¾” Blade Speed: 197 - 354 ft. / min. AMPS (120V): 6.5 A Vibration Level : 2.5 m/s2 Noise Level: 84 dB(A) Overall Length: 20” Net Weight: 13.2 lbs SPECIFICATIONS Blade Diameter: Max. 4-3/8” Arbor: 3/4” Maximum Cutting Capacity: 0o: 1-3/8” (34 mm) No Load Speed: 14,500 RPM Amps (120V): 9.6 A Overall Length: 9¼” Net Weight: 6.4 lbs HEAT GUN POWER SCRAPER 12.4 LBS. DEMOLITION HAMMER •Tool-less depth adjustment •Large shaft lock button enables quick and easy bit changes •2-Way “slide and bump” on/off switch •Airflow directed away from operator during operation •Dust proof ball bearings enhance durability and tool life •Ergonomic slim body for maximum operator comfort and control Includes: 1/8” drywall guide bit, 1/8” collet cone, 1/4” collet cone, wrench, and wrench holder Part No. 3706. •Ideal for welding and forming plastics, heat shrink tubing, soldering copper pipe, bending plastic pipe, thawing metal pipes, activating/de-activating adhesives and putties, stripping paint and more! •2-Stage air volume control provides versatility in a wide range of applications •Rear housing design with integrated rubber bumpers allows tool to be positioned upright for use as a static heating source during two-handed operations •Ergonomic soft rubber grip design for comfortable operation Includes: plastic carrying case Part No. HG5012. SPECIFICATIONS Air Temperature: 500°C (932°F) Air Volume: Low: 8.8 CFM (250 l/min) High: 14.1 CFM (400 l/min) AMPS (120V): 10 A Watts: 1,200 W Overall Length: 9.1” Net Weight: 1.28 lbs •Built in work light for excellent efficiency •Dual bearing blade guides for cutting •Blade tightening lever for fast and easy blade installation •Accepts standard 44-7/8” x 1/2” blade •Lightweight design •Electronic speed control dial •Very rigid design minimizes tool flex while cutting •Fluorescent job light with independent on / off switch Includes: carbon steel band saw blade, hex wrench, d-style front handle, and plastic carrying case Part No. 2107FK. •SDS-PLUS shank •Ideal for removing tile, linoleum, cleaning out mortar or detailed chiseling •Factory grease packed for maintenance free operation •Variable speed dial allows operator to adjust speed based on materials or application •One-touch sliding chuck for easy bit installation and removal •12 Angle bit positions enable chisels to be positioned at optimum angle of operation Includes: SDS-PLUS scaling chisel and plastic carrying case Part No. HK0500. SPECIFICATIONS Bit Type: SDS-PLUS Blows Per Minute: 2,000 - 3,500 BPM Impact Energy: 2.8 J (2.1 ft. lbs) AMPS (120V): 5.0 A Vibration Level: 9.5 m/s2 Noise Level: 83 dB(A) Overall Length: 18-13/32” Net Weight: 7.1 lbs •Dry cutting masonry saw for stone, masonry, tile, concrete and more •Heavy duty aluminum gear housing for increased durability •14Ga steel baseplate ensures accuracy and durability •Leading edge of baseplate indicates precise line of cut •Lock-off button prevents accidental startup for operator safety •Dust proof switch prevents contamination of motor •Flat motor housing allows tool to stand upright when changing blades Includes: 4” turbo rim diamond blade, wrench, and socket wrench Part No. 4100NH. •SDS-MAX Shank •Anti-Vibration Technology (AVT™) actively counteracts vibration of tool for greatly reduced transmission to operator •Constant speed control maintains constant speed under heavy load •Soft start feature gradually increases speed to eliminate start up shock •Variable speed dial allows operator to adjust speed based on materials or application •No-load motor suppression limits vibration and bit deflection when idling •Auto-shut off carbon brushes shut off motor when carbon brushes require replacement •Slide style on/off switch for easy continuous use applications •12 Angle bit positions enable chisels to be positioned at optimum angle of operation •One-touch sliding chuck for easy bit installation and removal •Led service light indicates appropriate time to change carbon brushes •Led power light indicates active power supply •Vibration absorbing handle with ergonomic soft rubber grip for vibration absorption and comfortable operation •Extra long carbon brushes for extended service life Includes: bit grease, side handle, cleaning cloth, and plastic carrying case Part No. HM0871C. 3¼” PLANER •Lightweight design for easy surface planing • Base plate foot protects materials and blade from damage •Single chamfering groove enables quick and easy chamfering of corners •Depth adjustment knob with click stops for precision planing applications •Lock-on button enables easy continuous operation and can be operated from left or right side •Ergonomic soft rubber grip design for vibration absorption and comfortable operation Includes: set of 3¼” double edged mini planer blades, blade gauge assembly, socket wrench 9, guide rule, and plastic carrying case Part No. KP0800KX. SPECIFICATIONS Maximum Capacities: Planing Width: 3¼” Planing Depth: 0-3/32” Shiplapping: 0 - 11/32” No Load Speed: 17,000 RPM AMPS (120V): 6.5 A Vibration Level: 2.5 m/s2 Noise Level: 89 dB(A) Overall Length: 11¼” Net Weight: 5.7 lbs SP01-10 GREGG DISTRIBUTORS LTD. SPECIFICATIONS Bit Type: SDS–MAX Blows Per Minute: 1,100 - 2,650 BPM Impact Energy: 11.6 J (8.6 ft. lbs) AMPS (120V): 10.0 A Vibration Level: 8.0 m/s2 Noise Level: 86 dB(A) Overall Length: 18-3/8” Net Weight: 12.3 lbs MAKITA MAK/2704 Power Tools 10” SLIDING COMPOUND MITRE SAW with LASER •Affordable, professional quality •Sliding rail mechanism incorporating 3 linear ball bearings provides increased rigidity to produce precise, adjustment free cuts right out of the box •Sliding fence (left side) can be adjusted outwards when bevel cutting or inwards for increased support of small or delicate materials •Soft start feature gradually increases speed to eliminate start up shock •Battery operated, factory calibrated class ii laser enables accurate alignment of blade and cutting line •Bevel capacity of 45° left or 5° right •Mitre capacity of 47° left or 60° right with positive stops at 0°, 15°, 22.5°, 31.6° & 45° •Re-located mitre scale enables easier viewing during operation •2 Stage safety switch for increased operator safety •Ergonomic vertical soft rubber grip design for vibration absorption and comfortable operation Includes: 10” C.T. Blade 40T, box wrench 13-3, dust bag, vertical vise, triangle rule, and 2 ea. Holder Part No. LS1017L. Part no. Ls1017lx, includes mitre saw and workstation for easy transport and jobsite portability. SPECIFICATIONS Blade Diameter: 10” Arbor: 5/8” No Load Speed: 4,200 RPM AMPS (120V): 13.0 A Vibration Level: 2.5 m/s2 Noise Level: 97 dB(A) Overall Dimensions (LxWxH): 32½” x 21-1/8” x 22-7/8” Net Weight: 42.8 lbs 12” DUAL SLIDING COMPOUND MITRE SAW •Up To 15” Cuts In 2x Material, 8” Nested Crown Moulding And 6½” Vertical Baseboard •Incorporates Makita’s NEW Deep And EXact Cutting Technology (DXT) •Dual sliding rail mechanism incorporating 6 linear ball bearings provides increased rigidity to produce precise, adjustment free cuts right out of the box •3 Stage gear reduction system greatly increases capacity when cutting vertical baseboard or nested crown molding •Quick adjust, dual sliding fences can be adjusted outwards when bevel cutting or inwards for increased support of small or delicate materials •Electronic speed control maintains constant speed under heavy load •Soft start feature gradually increases speed to eliminate start up shock •Bevel capacity of 45° left or right with positive stops at 0°, 22.5°, 33.9° & 45° •Mitre capacity of 52° left or 60° right with positive stops at 0°, 15°, 22.5°, 31.6° & 45° •Re-located mitre scale enables easier viewing during operation •Improved mitre lock for faster, simpler engagement during operation •2 Stage safety switch for increased operator safety •Ergonomic horizontal soft rubber grip design for vibration absorption and comfortable operation Includes: 12” C.T. blade 60T, box wrench 13, dust bag, 2 ea. Switch safety buttons, vertical Vise, triangle rule, and 2 ea. holder Part No. LS1216. Part No. LS1216L, Comes with factory calibrated class II laser enables accurate alignment of blade and cutting line. 14” POWER CUTTER •14” cutting wheel •Compliant with CARB tier 3, EPA phase 2 and EU stage 2 regulations •New scavenging losses rejection (slr) muffler recycles exhaust unburnt gas emissions for increased operational efficiency and cleaner emissions •Advanced 5 stage air filtration system for cleaner operation and enhanced operational life •Large air intake for maximum engine cooling •Reversible cutting arm enables cutting disc to be side or centre mounted for optimal operational versatility in a variety of applications •Electronic ignition with rev limiter •Always use with 2 cycle synthetic oil Includes: 14” cutting disk for stone 20 mm, tool kit, and water attachment kit Part No. EK7301, 20 mm arbor. Part No. EK7301HD, 1” arbor. SPECIFICATIONS Displacement: 4.5 cu.in (73 cc) Max. Power: 3.8 kW (5.1 H.P) Fuel / Oil Mixture: 50:1 Vibration Level : 6.2 m/s2 Noise Level: 100 dB(A) Fuel Tank Capacity: 1/3 Gal (1.1 L) No Load Speed (Engine): 9,400 RPM Max. Spindle Speed: 4,300 RPM Max. Cutting Depth: 4-13/16” Dry Weight: 22.5 lbs SPECIFICATIONS Blade Diameter: 12” Arbor: 1” No Load Speed: 3,200 RPM AMPS (120V): 15.0 A Vibration Level: 2.5 m/s2 Noise Level: 91 dB(A) Overall Dimensions (L xW x H): 31¾”x 25¼”x 28-3/8” Net Weight: 58.6 lbs Outdoor Power Equipment BLOWER / VACUUM •Double sided impeller and enlarged blower outlet provides increased air volume for maximum performance and efficiency •Self standing design allows tool to stand upright for use in stationary applications •Top and rear handle design enables comfortable positioning for optimal jobsite maneuverability •Converts quickly and easily between blower and vacuum modes •Variable speed trigger and dial enables operator to adjust blower or suction speed based on the material or application •Lock-on button for operator convenience during periods of prolonged use •Ergonomic soft rubber grip design for comfortable operation Includes: nozzle assembly and dust bag assembly Part No. UB1103. SPECIFICATIONS Max. Air Volume: 145 CFM (4.1 m3/min) Max. Air Velocity : 203 MPH (91 m/sec) No Load Speed: 0 - 16,000 RPM AMPS (120V): 6.8 A Vibration Level: 2.5 m/s2 Noise Level: 83 dB(A) Overall Length: 18 -7/8” Net Weight: 4.3 lbs HEDGE TRIMMER •Ergonomic soft rubber grip for vibration absorption and comfortable operation •Three switches are installed in handle, front grip and sub grip •2-Hand operation switch–motor will run only when grips are held with both hands •Guard is provided at the tip of blades to prevent kick-back •Blades are coated particularly to improve durability •Built in clutch for safety •Easy blade replacement •Powerful 550w motor •Protection of extension cord from breakage Includes: cord holder complete set,hook complete set,blade cover, and shear blade assembly set Part No. UH5570, 21-5/8” Bar. Part No. UH6570, 25½” Bar. SPECIFICATIONS Strokes Per Minute: 1,600 SPM AMPS(120V): 4.8 A Vibration Level : 6.7m/s2 Noise Level: 89.9 dB(A) Overall Length: 40½” Net Weight: 3.7 lbss www.greggdistributors.ca SP01-11 MAKITA MAK/2704 Outdoor Power Equipment 24.5 cc LINE TRIMMER •Makita mini 4-stroke series curved shaft trimmer for professional use •Professional series flexible shaft for maximum durability and minimum vibration •Wide trigger control and soft grip for comfortable operation •Primer bulb and choke for easy starting •Durable nylon string trimmer head •Outstanding power to weight ratio Includes: cutter assy, protective guard, box driver 10-16, hex wrench 4, engine oil set 80cc, starter rope, spark plug, and accessory bag Part No. ER2550LH. SPECIFICATIONS Cutting Width: 16¼” Displacement: 24.5 cc Maximum Engine Power: 0.71 Kw / 0.97 HP Carburator: Diaphram Type Fuel Tank Capacity: 0.5L (500 ml) Oil Tank Capacity: 0.08L (80 ml) 4-Stroke Crank Case Oil: 10W-30 Vibration Level : 5.4 m/s2 Noise Level: 93.3 dB(A) Overall Length: 64” Dry Weight: 10.8 lbs 33.5 cc 2 STROKE BRUSH CUTTER Save the cost of the brush cutter with fuel savings alone ! •Can be used on any angle or slope •Heavy duty solid steel straight shaft •Clean exhaust emissions and lower fuel consumption •Easy starting •Equipped with “swivel system” u-handle for maximum operator comfort •40% Less fuel consumption compared to 2-stroke equivalent Includes: 10” star blade, bump & feed trimmer head, protective guard, trimmer head protective guard attachment, boxwrench 16-17, hexwrench m4, hexwrench M5, shoulder harness, engine oil set 100cc, starter rope, spark plug, tool cover, and accessory bag Part No. EBH341U. SPECIFICATIONS Cutting Width: 10” With Blade 16” With Line Head Displacement: 33.5 cc Maximum Engine Power: 1.07 Kw / 1.435 HP Carburetor: Diaphragm Type Fuel Tank Capacity: 0.65L (650 ml) Oil Tank Capacity: 0.1L (100 ml) 4-Stroke Crank Case Oil: 10W-30 Vibration Level: 3.3 m/s2 Noise Level: 98.2 dB(A) Overall Length: 71¼” Dry Weight: 15.7 lbs SP01-12 GREGG DISTRIBUTORS LTD. 24.5 cc LINE TRIMMER •Save the cost of the trimmer with fuel savings alone ! •Can be used on any angle or slope •Anti-vibration system for fatigue free use •Clean exhaust emissions and lower fuel consumption •Easy starting •40% Less fuel consumption compared to 2-stroke equivalent Includes: trimmer head assy, protective guard, trimmer head protective guard attachment, boxwrench 16-17, hexwrench M4, hexwrench M5, shoulder harness, engine oil set 80cc, starter rope, spark plug, and accessory bag Part No. EBH253L. SPECIFICATIONS Cutting Width: 16” Displacement: 24.5 cc Maximum Engine Power: 0.71 Kw / 0.97 HP Carburator: Diaphram Type Fuel Tank Capacity: 0.5L (500 ml) Oil Tank Capacity: 0.08L (80 ml) 4-Stroke Crank Case Oil: 10W-30 Vibration Level: 5.3 m/s2 Noise Level: 97.1 dB(A) Overall Length: 69¾” Dry Weight: 11.5 lbs 25.7 cc LINE TRIMMER •Compliant with EPA phase 2, EU stage 2 exhaust emissions regulations •Wide trigger control and soft grip for comfortable operation •Primer bulb and choke for easy starting •Durable nylon string trimmer head Includes: protector assy, protector, trimmer head, band assembly, socket wrench M5, tool kit, and spark plug Part No. EM2600L. SPECIFICATIONS Cutting Width: 9” Displacement: 25.7cc Maximum Engine Power: 0.83 Kw / 1.15 HP Carburator: Diaphram Type Fuel / Oil Mixture: 50:1 Fuel Tank Capacity: 0.6L (600 ml) Overall Length: 69¾” Dry Weight: 10.8 lbs 32 cc. CHAINSAW 35 cc CHAINSAW SPECIFICATIONS Displacement: 32 cc. Chain Pitch / Gauge: 3/8” / .050” Maximum Engine Speed: 12,800 RPM Power Rating: 1.35 kW / 1.8 H.P. Vibration Level: 4.8 m/s2 Noise Level: 102.6 dB(A) Fuel / Oil mixture: 50:1 Fuel Tank Capacity: 400 ml Oil Tank Capacity: 280 ml Net Weight: Dry w/O/Bar/Chain: 9.4 lbs. SPECIFICATIONS Displacement: 35 cc. Chain Pitch / Gauge: 3/8” / .050” Max. Engine Speed: 13,100 RPM Power Rating: 1.7 kW / 2.3 H.P. Vibration Level: 530 m/s2 Noise Level: 101.8 dB(A) Fuel / Oil Mixture: 50:1 Fuel Tank Capacity: 400 ml Oil Tank Capacity: 290 ml Net Weight Dry w/o Bar/Chain: 9.9 lbs •16” Bar •Touch and stop switch automatically returns switch to start position, eliminating carburetor flooding •Intelligent ignition coil controls stable idling, increases output power, protects against engine overrun and enables easier restarting •Toolless chain tension adjustment for quick and easy adjustment on the jobsite •Throttle-lock start position •External access holes allow easy carburetor adjustment •Primer pump for easy starting •Automatic chain oiler •Inertia chain brake Includes: 16” guide bar, 16” chain, chain cover 16”), universal wrench, screwdriver, spark plug, and starter rope Part No. EA3201S40B. •16” Bar •Touch & stop switch automatically returns switch to start position, eliminating carburetor flooding •Intelligent ignition coil controls stable idling, increases output power, protects against engine overrun and enables easier restarting •Toolless chain tension adjustment for quick and easy adjustment on the jobsite •Throttle-lock start position •External access holes allow easy carburetor adjustment •Primer pump for easy starting •Automatic chain oiler •Inertia chain brake Includes: 16” guide bar, 16” chain, chain cover, and universal wrench Part No. EA3501S40B. MAKITA MAK/2704 Outdoor Power Equipment 43 cc 2 STROKE CHAINSAW •18” Bar •Touch & stop switch automatically returns switch to start position, eliminating carburetor flooding •Catalytic converter reduces engine emissions for reduced environmental impact •Throttle-lock start position with decompression valve for reduced start up force •External access holes allow easy carburetor adjustment •Primer pump for easy starting •Automatic chain oiler •Inertia chain brake Includes: .325” Chain 18” 50g, 18” sprocket nose bar, chain protector cover, universal wrench, offset screwdriver, and screwdriver (for carburetor adjustment) Part No. EA4300F45C. SPECIFICATIONS Displacement: 42.4 cc Chain Pitch / Gauge: .325” / .050” Maximum Engine Speed: 13,500 RPM Power Rating : 2.1kW / 2.9 H.P Noise Level: 100.8 dB(A) Fuel / Oil Mixture (Makita Oil): 50:1 Fuel Tank Capacity: 480 ml Oil Tank Capacity: 280 ml Dry Weight w/o Bar/Chain: 10.8 lbs 50 cc. CHAINSAW •18” Bar •Throttle-lock start position •External access holes allow easy carburetor adjustment •Automatic chain oiler •Electronic ignition •Inertia chain brake •Large diameter fuel / oil caps with external fuel indicator •Handles and grips proportioned for optimum comfort Includes: 18” chain,18” guide bar, chain cover, and tool kit Part No. DCS5121-18. SPECIFICATIONS Displacement: 50 cc. Chain Pitch / Gauge: .325” / .058” Max. Engine Speed: 13,800 RPM Power Rating: 2.5 kW / 3.3 H.P. Noise Level: 103.9 dB(A) Fuel Tank Capacity: 470 ml Oil Tank Capacity: 269 ml Fuel / Oil MixtureL 50:1 Net Weight Dry w/o Bar/Chain: 12.1 lbs 64 cc. CHAINSAW •20” Bar •Throttle-lock start position with decompression valve •External access holes allow easy carburetor adjustment •Automatic adjustable chain oiler •Electronic ignition system incorporates a microprocessor •Inertia chain brake Includes: 20” chain,20” guide bar, chain cover, and tool kit Part No. DCS6421-20. SPECIFICATIONS Displacement: 64 cc. Chain Pitch / Gauge: 3/8” / . 058” Max. Engine Speed: 13,500 RPM Power Rating: 3.5 kW / 4.7 H.P. Noise Level: 101.4 dB(A) Fuel Tank Capacity: 750 ml Oil Tank Capacity: 420 ml Fuel / Oil Mixture: 50:1 Net Weight: Dry w/o Bar/Chain: 13.9 lbs 73 cc 2 STROKE CHAINSAW •20” Bar •Scavenging losses rejection (slr) muffler recycles exhaust emissions for increased operational efficiency and cleaner emissions •Throttle-lock start position with decompression valve for reduced start up force •External access holes allow easy carburetor adjustment •Automatic chain oiler •Inertia chain brake Includes: 20” chain, 20” guide bar, chain cover, and tool kit Part No. EA7300P50E. SPECIFICATIONS Displacement: 72.6 cc. Chain Pitch / Gauge: 3/8” / . 058” Max. Engine Speed: 10,000 RPM Power Rating: 4.0 kW / 5.4 H.P. Fuel Tank Capacity: 750 ml Oil Tank Capacity: 420 ml Fuel / Oil Mixture: 50:1 Noise Level: 101.4 dB(A) Net Weight: Dry w/o Bar/Chain: 13.8 lbs MR. HEATER® EEE/1749 Forced Air Propane Heaters Heavy-duty design built for the jobsite. The Mr. Heater Liquid Propane Air Heater comes with a standard 10 ft. hose, regulator and all the safety you would expect of a Mr. Heater product. Equipped with factory installed high limit switches and thermoelectric safety valves, you can feel comfortable using these heaters on any jobsite. Just plug the heater into a 110v outlet, hook up the included hose and regulator to a 20 lb. propane tank or larger, and you are ready to take the chill out of any job. All heaters come equipped with Quite Burner Technology™. QBT heaters are quieter than standard propane heaters by as much as 50%. Typical uses include: construction sites, patios, factories, sporting events, utility and out buildings, and farming functions. CSA certified. •35,000 BTU/Hr. •Heats approximately 800 sq. ft. •Runs up to 12 hours on 20 lb. tank (not included) •Piezo ignition Part No. MH38QFA. •30,000 - 60,000 BTU/Hr. •Heats approximately 1,250 sq. ft. •Runs up to 14 hours on 20 lb. tank - low setting (not included) •Continuous ignition Part No. MH60QFAV. •50,000 - 85,000 BTU/Hr. •Heats approximately 2,000 sq. ft. •Runs up to 8 hours on 20 lb. tank - low setting (not included) •Continuous ignition Part No. MH85QFAV. •75,000 - 125,000 BTU/Hr. •Heats approximately 3,000 sq. ft. •Runs up to 11 hours on 40 lb. tank - low setting (not included) •Continuous ignition Part No. MH125QFAV. •125,000 - 170,000 BTU/Hr. •Heats approximately 4,000 sq. ft. •Runs up to 17 hours on 100 lb. tank - low setting (not included) •Automatic solid state ignition •Thermostat Part No. MH170QFAVT. www.greggdistributors.ca SP01-13 NORTON NRN/1549 Diamond Tools and Accessories HIGH-SPEED CP-500 SERIES SAWS The Norton Clipper CP500 high-speed cut-off saw is destined to be an asset on any crew. It’s fully designed with the user in mind to not only cut a smooth, fast track, but it’s also fully equipped to handle the everyday performance of any jobsite with unrelenting durability and reliability. Select a standard model or upgrade to the world’s first patented automatic lubrication system, iLube®. Features: No More Pre-Mixing Oil and Fuel The patented iLube® option automatically controls mixing of oil and fuel for maximum efficiency. An electronic sensor will indicate a low oil level and adjust the engine to idle to prevent engine damage. Easy Start – Hot or Cold The electronic carburetor’s electromagnetic valve eliminates the standard choke and half throttle start. The 3-step easy start eliminates the hassle of a choke. Simply turn the switch on, prime the engine, and push the decompression button, then pull the cord to start. Technical Specifications Part No. 47559 Blade Guard Capacity 12” (305 mm) Maximum Depth of Cut 4” (100 mm) Arbor Size .78 (20 mm) Blade Flange Diameter 3.93 (100 mm) Blade Shaft RPM 4,500 Blade Shaft Bearings Heavy Duty Sealed Blade Shaft Drive 1 Belt Control Hand Held Chassis Norton Single-Cylinder Two Stroke Engine Power Source Single Cylinder 2 Cycle Motor/Engine Type Norton Clipper Specifications: CP512-300 5.4 HP (4.0 kW) Maximum Horsepower* 5.4 HP (4.0 kW) Net Horsepower* Max. Torque 3.54 ft lbs (4.8 Nm) Displacement 4.94 cu in (81 l) Bore 2.04” (52 mm) Stroke 1.49” (38 mm) Cylinders/Cycle Single Cylinder 2 Cycle Fuel Capacity 0.23 gal (0.9 l) Oil Capacity - Electronically-Controlled Oil Lubrication - Air Filter Heavy Duty 3 Stage Starter Manual Engine Cooling Forced Air Electronically-Controlled Carburettor With Smart Choke YES “Sound Level2,3 Lpeg (EN ISO 19432 Annex B) dB(A)” 98 Sound Power Level2,3 Lweg (EN ISO 19432 Annex B) dB(A) 108 “Weighted Effective Acceleration 2,4 ahv,eq (EN ISO 19432 Annex C) Rear Handle / Top Handle m/s²” 4.5 / 6.0 Saw Dimensions Height 16.93” (430 mm) Saw Width 10.52” (267 mm) Maximum Saw Length (Working) 29.53” (750 mm) Weight 22.26 lbs (10.1 kg) *Data provided by motor/engine manufacturer Accessories Part No. 09845, High-Speed Saw Wheel Kit. SP01-14 GREGG DISTRIBUTORS LTD. Multi-Stage Air Filtration Patented twin-air inlets create an air pulsation that draws fresh air in while pushing hot air away from the engine and releasing it out the back to keep the saw running cool and reduce debris being trapped in the filter. The external rocker wheel vibrates the filter to further help release debris. This system extends filter life for less cleaning/replacement. 47561 12” (305 mm) 4” (100 mm) .78 (20 mm) 3.93 (100 mm) 4,500 Heavy Duty Sealed 1 Belt Hand Held Norton Single-Cylinder Two Stroke Engine Single Cylinder 2 Cycle w/iLube Norton Clipper CP512-300i 5.4 HP (4.0 kW) 5.4 HP (4.0 kW) 3.54 ft lbs (4.8 Nm) 4.94 cu in (81 l) 2.04” (52 mm) 1.49” (38 mm) Single Cylinder 2 Cycle 0.23 gal (0.9 l) 10.08 oz (0.32 l) YES Heavy Duty 3 Stage Manual Forced Air YES 47563 14” (356 mm) 5” (125 mm) .78 (20 mm) 3.93 (100 mm) 4,500 Heavy Duty Sealed 1 Belt Hand Held Norton Single-Cylinder Two Stroke Engine Single Cylinder 2 Cycle Norton Clipper CP514-350 5.4 HP (4.0 kW) 5.4 HP (4.0 kW) 3.54 ft lbs (4.8 Nm) 4.94 cu in (81 l) 2.04” (52 mm) 1.49” (38 mm) Single Cylinder 2 Cycle 0.23 gal (0.9 l) - - Heavy Duty 3 Stage Manual Forced Air YES 47565 14” (356 mm) 5” (125 mm) .78 (20 mm) 3.93 (100 mm) 4,500 Heavy Duty Sealed 1 Belt Hand Held Norton Single-Cylinder Two Stroke Engine Single Cylinder 2 Cycle w/iLube Norton Clipper CP514-350i 5.4 HP (4.0 kW) 5.4 HP (4.0 kW) 3.54 ft lbs (4.8 Nm) 4.94 cu in (81 l) 2.04” (52 mm) 1.49” (38 mm) Single Cylinder 2 Cycle 0.23 gal (0.9 l) 10.08 oz (0.32 l) YES Heavy Duty 3 Stage Manual Forced Air YES 98 98 98 108 108 108 4.5 / 6.0 4.5 / 6.0 4.5 / 6.0 16.93” (430 mm) 10.52” (267 mm) 29.53” (750 mm) 22.92 lbs (10.4 kg) 16.93” (430 mm) 10.52” (267 mm) 30.52” (775 mm) 22.49 lbs (10.2 kg) 16.93” (430 mm) 10.52” (267 mm) 30.52” (775 mm) 23.15 lbs (10.5 kg) NORTON NRN/1549 Diamond Tools and Accessories WALK BEHIND C13PE GASOLINE SMALL PUSH SAW Rental equipment has to withstand any and all conditions by user and application. For that reason, the Norton Clipper C13PE suits any rental fleet that both the novice and expert will appreciate to hold-up through tough situations. The 18” blade guard, ride-on water system and quick-release blade guard lock keeps safety in mind while the rugged frame, powerful engine and easy-to-use console makes cutting a breeze. Features: Fast Release Guard The quick release pull pin keeps the blade guard locked down for safety during operation. No more jam nuts or tools needed - just pull and lift. The next generation of 13HP saws. The C1318P features shock-absorbing handle bars. The new sleek design of the water tank, with increased capacity and improved securing, adds an additional 1.5 gallons of water over the cut. And, a newly-designed belt tensioning system helps keep the saw cutting tried and true. All these features, coupled with the Honda 13HP engine, makes the C1318P the premiere choice for rental and service work. Tough Frame and Raised Axle Thick, heavy-duty gauge metal frame endures the hardest of users and job sites. Resists twisting for a tried and true straight cut. Technical Specifications Part No. Blade Guard Capacity Maximum Depth of Cut Arbor Size Blade Flange Diameter Blade Shaft RPM Blade Shaft Diameter Blade Shaft Bearings Blade Shaft Drive Blade Guard Attachment Blade Control Axle - Front Axle - Rear Wheels - Front - D x W x B Wheels - Rear - D x W x B Power Source Motor/Engine Type Specifications Maximum Horsepower* Net Horse Power* Displacement Bore Stroke Cylinders/Cycle Fuel Capacity Oil Capacity Air Filter Starter Engine Cooling Saw Dimensions Height - in (mm) Minimum Saw Length (Transport) Maximum Saw Length (Working) Maximum Pointer Length Frame Width Saw Width Front (Outside to Outside Wheel Width) Rear (Outside to Outside Wheel Width) Blade to Wall Wheel Base Length Tool Weight *Data provided by motor/engine manufacturer WALK BEHIND C1318P GASOLINE SMALL PUSH SAW Uncomplicated Control Panel Everything at your fingertips to manage the saw with ease: depth locking mechanism, emergency shut off and water valve within easy reach. Features: Vibration Reducing Handle Bars Shock-absorbing handle bars reduce vibrations up to 40%. Quick Belt Tensioning Provides fast and accurate belt tensioning. Technical Specifications Part No. Blade Guard Capacity 47524 Maximum Depth of Cut 18” (457 mm) Arbor Size 6-5/8” (168 mm) Blade Flange Diameter 1” (25 mm) Blade Shaft RPM 4½” (114 mm) Blade Shaft Diameter 2,700 Blade Shaft Bearings 1.00” (25.4 mm) Blade Shaft Drive Heavy Duty Pillow Block Blade Guard Attachment 3 Belts Blade Control Hinged, All Steel Axle – Front Hand Wheel/Screw Feed Axle – Rear .75” (19 mm) Wheels – Front - D x W x B .75” (19 mm) 4” x 1.5” x .75” (102 mm x 38 mm x 19 mm) Wheels – Rear - D x W x B 8” x 2.50” x .75” (203 mm x 64 mm x 19 mm) Handle Bars/Adjustment Length Control Gasoline, Single Cylinder 4 Cycle Speed Honda GX390 Chassis GX390K1QXC9 13 HP (9.5 kW) Power Source 11 HP (8.2 kW) Engine Type 23.7 cu in (0.39 l) Specifications 3.5” (88 mm) Maximum Horsepower* 2.5” (64 mm) Net Horsepower* Single Cylinder 4 Cycle Displacement 1.79 gal. (6.5 l) Bore 1.16 qt. (1.1 l) Stroke Four Stage Cyclone Cylinders/Cycle Manual Fuel Capacity Forced Air Oil Capacity Air Filter 38-13/16” (986 mm) Starter 42¾” (1086 mm) Engine Cooling 63” (1600 mm) Saw Dimensions 20” (508 mm) Height 16½” (419 mm) Minimum Saw Length (Transport) 21-27/64” (544 mm) Maximum Saw Length (Working) 14-17/32” (369 mm) Maximum Pointer Length 19-9/32” (490 mm) Frame Width 1-23/32” (44 mm) Saw Width 15¾” (400 mm) Front (Outside to Outside Wheel Width) 220 lbs (100 kg) Rear (Outside to Outside Wheel Width) Blade to Wall Wheel Base Length Tool Weight Fast Blade Guard Lock No hassle, blade guard securing lock. 42453 18” (457 mm) 6-5/8” (168 mm) 1” (25 mm) 4½” (114 mm) 2,573 1.18” (30 mm) Heavy Duty Pillow Block Single 10 Groove Belt Hinged, All Steel Hand Wheel/Screw Feed .78” (20 mm) .78” (20 mm) 4.92” x 1.96 x .78 (125 mm x 50 mm x 20 mm) 8” x 1¼” x .78 (203 mm x 32 mm x 20 mm) 6¼” (160 mm) 5.28 gal. (20 l) Push Heavy Duty Steel Box with Longitudinal and Horizontal Reinforcements Gasoline, Single Cylinder 4 Cycle Honda GX390 GX390K1QXC9 13 HP (9.5kW) 11 HP (8.2 kW) 23.7 cu in (0.39 l) 3.5” (88 mm) 2.5” (64 mm) Single Cylinder 4 Cycle 1.79 gal. (6.5 l) 1.16 qt. (1.1 l) Four Stage Cyclone Manual Forced Air 39” (990 mm) 33½” (850 mm) 61½” (1,562 mm) 20-7/8” (528 mm) 16½” (421 mm) 22” (609 mm) 10-7/16” (265 mm) 16.89” (429 mm) 4½” (114 mm) 13” (332 mm) 220 lbs (100 kg) www.greggdistributors.ca SP01-15 NORTON NRN/1546/1549 Diamond Tools and Accessories WALK BEHIND GC55 EARLY ENTRY / GREEN SMALL PUSH SAW With a compact, light-weight design backed by the reliable Honda 5.5 HP gasoline engine, the GC55 early entry saw is intended for a variety of applications. From green, cured or decorative concrete cutting to expansion joints, the features of this small push saw are hard to beat in a single saw. The low, wide profile of the frame, along with the front mount blade, contribute to producing a more disciplined cut. Features: Gasoline Engine Mounted with the dependable Honda 5.5 HP engine for best performance. Technical Specifications Part No. Blade Guard Capacity Maximum Depth of Cut Arbor Size Blade Flange Diameter Blade Shaft RPM Blade Shaft Diameter Blade Shaft Bearings Blade Shaft Drive Blade Guard Attachment Blade Control Axle – Front Axle – Rear Wheels – Front – D x W x B Wheels – Rear – D x W x B Handle Bars/Adjustment Length Control Chassis Power Source Motor/Engine Type Specifications Maximum Horsepower Net Horse Power Displacement Bore Stroke Cylinders/Cycle Fuel Capacity Oil Capacity Air Filter Starter Engine Cooling Saw Dimensions Height Minimum Saw Length (Transport) Maximum Saw Length (Working) Maximum Pointer Length Frame Width Saw Width Front (Outside to Outside Wheel Width) Rear (Outside to Outside Wheel Width) Blade to Wall Wheel Base Length Tool Weight Front Blade Mount Additional weight helps keep the blade in the cut. Improved Wheel Design Stable cutting over debris to help keep the saw in line of cut. 30005 10” (254 mm) 3¾” (95 mm) 5/8” (15.9 mm) 3-5/64” (78 mm) 3,000 7/8” (20 mm) Sealed Radial Bearings 1 Cogged All Steel Screw Feed 55/64” (22 mm) 55/64” (22 mm) 3-3/8” x 2¾” x 25/32” (85 mm x 70 mm x 20 mm) 3-3/8” x 2¾” x 25/32” (85 mm x 70 mm x 20 mm) 6” (152.4 mm) Push Heavy Duty Stamped Steel with Reinforcements Single Cylinder 4 Cycle Honda GX160 GX160K1QXC9 5.5 HP (4.1 kW) – * 4.8 HP (3.6 kW) – * 9.9 cu in (0.16 l) 2.7” (68 mm) 1.8” (45 mm) Single Cylinder 4 Cycle .95 gal (3.6 l) .63 qt (.6 l) Four Stage Cyclone Manual Forced Air 24-7/32” (615 mm) 32” (813 mm) 42-29/32” (1,090 mm) 8-7/32” (209 mm) 13-11/16” (348 mm) 18-1/8” (460 mm) 8-21/32” (220 mm) 13” (330 mm) 7½” (190) 19” (483 mm) 115 lbs (52 kg) *= Data Provided by Motor/Engine Manufacturer SP01-16 GREGG DISTRIBUTORS LTD. Fold-Down Design Easy storage and transport. GMAX – MULTI - PURPOSE BLADES DRY – GREEN/CURED CONCRETE WALK BEHIND BLADES Designed specifically for the #30005 down-cut green concrete push saw, the GMAX Multi-Purpose blade is excellent in both green and cured concrete. The unique segment specification and anchor slot gullet allows this blade to be used in a variety of applications with outstanding results. Part No. 83758 75125 84508 Size Max RPM 8 x .095 x 7/8-5/8 8,730 9 x .110 x 7/8-5/8 6,600 10 x .110 x 1-7/8-5/8 6,115 Segment Height .295” .295” .295” NORTON NRN/1549 Diamond Tools and Accessories BBM BLOCKBUSTER MINI MASONRY SAWS The innovative design of these small masonry saws has been copied many times due to its compact, all-steel unibody construction, giving the best weight-to-strength distribution. A 14” blade capacity and ergonomically-designed, three-position locking, cutting head provides a safe, clear view of the work area. Whether your choice is the 3 HP brush motor or the 1.5 HP induction motor for heavier commercial use, both come with features such as overload protection, garden hose connection and a channeled, flow water pan to direct dust and slurry away from the operator. Norton diamond blade included with saw . Features: All Steel Construction All welded strong honeycomb reinforcement design. Technical Specifications Part No. Blade Guard Capacity Maximum Depth of Cut Arbor Size Blade Flange Diameter Blade Shaft RPM Blade Shaft Bearings Blade Shaft Drive Blade Guard Attachment Conveyor Cart Water Pump Frame Power Source Motor/Engine Type Specifications Net Horsepower Voltage Cycle/Current/Phase Full Load Amps Engine Cooling Air Filter Saw Dimensions Saw Length Saw Width Saw Height Maximum Arbor Height Over Table Cart Length Cart Width Pan Length Pan Width Tool Weight Pivoting Locking Head Plunge/step cutting and jam cutting (all the way down). Clear View Cutting System Offset of motor and blade allows operator to see the complete cutting surface. Wet or Dry Cutting Quick attach garden hose water system. 00684 14” (355 mm) 5” (127 mm) 1” (25 mm) 4” (100 mm) 3,600 Sealed Radial Bearings Gear Drive All Steel, Pivoting Posi-Loc Cutting Head Aluminum With Steel Wheels and Seal Bearings Optional Steel Reinforced Frame Electrical AC Universal Motor Carbon Brush, Thermal Protection 3 HP 115 volts 60Hz/AC/1 10 Amps Forced Air Yes 26327 14” (355 mm) 5” (127 mm) 1” (25 mm) 4” (100 mm) 2,800 Sealed Radial Bearings Belt Drive All Steel, Pivoting Cutting Head Aluminum With Steel Wheels and Seal Bearings Optional Steel Reinforced Frame Electrical Induction T.E.F.C., Thermal Protection 2 HP 115/230 volts 60Hz/AC/1 15 Amps Forced Air - 31½” (800 mm) 18” (470 mm) 30” (762 mm) 15-1/16” (383 mm) 10-7/16” (265 mm) 16-17/32” (420 mm) 30-1/8” (765 mm) 16” (405 mm) 75 lbs (34 kg) 31½” (800 mm) 18” (470 mm) 27¾” (695 mm) 16-17/32” (420 mm) 10-7/16” (265 mm) 16-17/32” (420 mm) 30-1/8” (765 mm) 16” (405 mm) 123.2 lbs (56 kg) Accessories Part No. 00704, Wet Kit. Part No. 00691, Stand. www.greggdistributors.ca SP01-17 NORTON NRN/1549 Diamond Tools and Accessories CTC1020XL TILE SAW Built with the professional in mind, the CTC1020XL is the newest to the tile industry. The powerful 2 HP motor makes ripping materials, up to 24”, trouble-free. The combination of having a light-weight, sturdy frame and a newly designed polypropylene pan, to help reduce area contamination, gives an operator all the essentials to get the job done quickly and efficiently. Norton diamond blade included with saw . CTC705 TILE SAW A great value for a 7” tile saw that can handle the small to medium size jobs. This saw has many features of more expensive tile saws, like a belt-driven 1 HP motor for maximum motor-to-blade power. A sturdy aluminum cutting table with anti-skid top for keeping material in place while cutting and a light-weight water pan for easy cleaning and/or single operator use getting on and off the site. Norton diamond blade included with saw . Features: Features: 2 HP Motor More powerful than using conventional 1.5 HP and can make a rip cut of 24” tile. Light-Weight 60 lbs vs. standard 100-125 lbs for easier transportation. Aluminum Rails with Stainless Insert Provides long life and easy portability due to low coefficient of friction, creating smoother slide. Technical Specifications Part No. Blade Guard Capacity Maximum Depth of Cut Arbor Size Blade Flange Diameter Blade Shaft RPM Maximum Material Size Rip Cut Size Diagonal Size Cut Depth Cutting Head Built-In 45° Miter Cut Cutting Table Water Pump Power Source Motor/Engine Type Maximum Horsepower Voltage Cycle/Current/Phase Full Load Amps Saw Dimensions Saw Length Saw Width Saw Height Saw Height With Stand Arbor to Top of Cart Cart (Table) Length Cart (Table) Width Cart Travel Pan Length Pan Width Tool Weight Upgraded Backsplash Pan Catches water on larger tile/block cutting and easily detaches. 30013 10” (254 mm) 3¾” (88 mm) 5/8” (16 mm) 3 (78 mm) 3,000 24” x 24” (610 mm x 610 mm) 24” (610 mm) 18” (457 mm) 3¾” (95 mm) Cast Aluminum NO, Includes Miter Block Aluminum With Rubber Coating YES Electric Brush Motor with Thermal Protection 2 HP 115 volt 60 Hz/AC/1 8 Amp 51-7/8” (1,318 mm) 25-3/16” (640 mm) 20-7/8” (530 mm) 41-13/16” (1,240 mm) 4¾” (120 mm) 16” (406 mm) 16-9/64” (410 mm) 22-5/8” (575 mm) 51-7/8” (1,318 mm) 25-3/16” (640 mm) 65 lbs (29.5 kg) Accessories Part No. 43045, Premium Stand w/Work Table. SP01-18 GREGG DISTRIBUTORS LTD. Motor Upgrade Strong belt-driven 1 HP motor provides powerful and precise cutting. Light-Weight Conveyor Smooth slide creates straight cuts and has a locking mechanism for easier transportation. Water Pump High intake and output to keep fresh water in pan with a durable filter to keep debris out. Technical Specifications Part No. Blade Guard Capacity Maximum Depth of Cut Arbor Size Blade Flange Diameter Blade Shaft RPM Maximum Material Size Rip Cut Size Diagonal Size Cut Depth Cutting Head Built-In 45° Miter Cut Cutting Table Water Pump Power Source Motor/Engine Type Maximum Horsepower Voltage Cycle/Current/Phase Full Load Amps Saw Dimensions Saw Length Saw Width Saw Height Saw Height With Stand Arbor to Top of Cart Cart (Table) Length Cart (Table) Width Cart Travel Pan Length Tool Weight 81496 7” (177 mm) 2¼” (57 mm) 5/8” (16 mm) 2½” (66 mm) 6,000 17” (431 mm) 17” (431 mm) 12” (305 mm) 1¾” (44.5 mm) Cast Aluminum No Aluminum Yes Electric Carbon Brush 1 HP 115 volt 60 Hz/AC/1 10 Amps 30” (762 mm) 19¾” (502 mm) 17½” (445 mm) 47¾” (1,213 mm) Adjustable 14¼” (362 mm) 15” (381 mm) 18¾” (477 mm) 30” (762 mm) 43 lbs (19.5 kg) Accessories Part No. 43045, Premium Stand w/Work Table. NORTON NRN/1549 Diamond Tools and Accessories CTC701 TILE SAW DR620 CORE DRILL RIG The simple design of the tabletop tile saw features a powerful professional motor that veterans and novices alike will enjoy operating. Its solid construction incorporates a self-contained water pan with plug release, tilting table for miter cuts and a fast, precise lockable cutting guide. The robust carrying case allows for easy transportation or storage while protecting the unit Features: Built-In Water Pan Single unit design with optimized water recycling. The Norton Clipper DR series of core drills offer a versatile drill rig with exceptional utility to meet the tough demands of today’s rental and contractor industry. The basic design of the carriage and pinion assembly provides a simple trouble-free system to extend service life in the rental fleet. The DR620 drill rig stand offers the additional utility of a pivoting column for drilling vertically on a sloping surface. Features: Vacuum Pump Superior stabilization. Chrome Steel Tilting Table Convenient for miter cutting of 0-45º cuts with a tilt design to allow for quicker blade changes. Quick Locking Rip Guide Secures guide position for precise cuts. Wheel Attachment Ease of transporting around job site. Ceiling Jack Extending ceiling jack for indoor drilling. Technical Specifications Part No. Blade Guard Capacity Maximum Depth of Cut Arbor Size Blade Flange Diameter Blade Shaft RPM Cut Depth Cutting Head Built-In 45° Miter Cut Cutting Table Water Pump Power Source Motor/Engine Type Maximum Horsepower Voltage Cycle/Current/Phase Full Load Amps Saw Dimensions Saw Length Saw Width Saw Height Tool Weight 30029 7” (177 mm) 2¼” (57 mm) 5/8” (16 mm) 3 (78 mm) 2,990 1-9/16” (40 mm) Steel YES Chrome Steel Blade Rotates In Water Pan Electric T.E.F.C. 1.5 HP 115 volt 60 Hz/AC/1 7 Amps 18.11” (460 mm) 14.17” (360 mm) 11-7/16” (290 mm) 35 lbs (15.9 kg) Technical Specifications Part No. Gears Motor Type Motor Specification Voltage Cycle/Current/Phase Amperage RPM Spindle Thread Size Base – Combo – L x W Column Length Slide Carriage Wheel Base (outside to outside) Wheels (D x W x B) Vacuum Pump Control Panel Tool Weight Recommended Bit Sizes Low High 00926 2 Cardi D3-250-EL 115 volts 60 Hz/AC/1 25 Amp 450/900 1¼”-7 UNC 18-7/8” x 13¾” (450 mm x 350 mm) 40” (1,016 mm) One Piece Aluminum Carriage, Rack and Pinion, Carriage Lock, and Quick Detach Motor Mount Dove Tail 15½” (394 mm) 6” x 1-3/8” x 3/4” (152 mm x 35 mm x 19 mm) YES YES 120 lbs (54.4 kg) 6” to 10” (152 mm to 305 mm) 2” to 6” (50 mm to 152 mm) HHDET 1800 HAND-HELD CORE DRILL A light-weight and user-friendly core drill. With its “Smart Electronics”motor protection from Cardi means no overheating of electrical parts. The powerful 15 amp motor drives core bits up to 4” with ease. The hand-held core drill has a singlespeed gear box and mechanical safety clutch. Packaged in a rugged carrying case to protect the drill during transport. Technical Specifications Part No. 84243 Gears 1 Motor Type Electric Voltage 115 volts Cycle/Current/Phase 60Hz/AC/1 Amperage 15 Amps RPM (No Load) 940 Smart Electronics YES Weight Crated 18 lbs (8.1 kg) Weight Uncrated 12 lbs (5.4 kg) Recommended Bit Sizes Low 2” to 4” (50 mm to 102 mm) Features: Smart Electronics Protection No over-heating of electrical components. Water Attachment and Accessories 1¼-7 Male with 5/8-11 adapter and quick attach water accessories for wet drilling. Rugged Carrying Case Protects unit and accessories from damage. www.greggdistributors.ca SP01-19 NORTON NRN/1546 High Speed Diamond Blades MULTI-PURPOSE, ALL MATERIALS BLADES - DRY - SEGMENTED RIM Used for: Concrete, reinforced concrete, granite, building materials, thin steel sections, angle iron up to 1/2” material thickness, rebar up to no. 5. 4X4 MAX CUT BLADES Taking high-speed cutting versatility to an all new level. The same standard features as the 4X4 with its anti-crack gullets and patented depth indicators that not only cool the blade but also allow the operator to know how deep they are cutting. An all new bond and diamond specification improves blade life in a wide range of materials while excelling in steel. New segment wear indicators give the operator an idea of remaining blade life. Part No. 45927 45926 Size Max RPM 12 x .118 x 1/20 mm 6,300 14 x .125 x 1/20 mm 5,460 3X3 BLADES It’s everything expected for high-speed cutting when both performance and price are a factor. The laser welded 3X3 cuts concrete, reinforced concrete, asphalt, abrasive building materials and more. High quality diamond increases the speed of cut on a variety of materials without changing blades. Premium blade characteristics and price point where it would take multiple sintered blades to achieve. Segment Height .472” .472” Part No. 47500 47499 Size Max RPM 12 x .118 x 1/20 mm 6,300 14 x .118 x 1/20 mm 5,460 Segment Height .314” .314” ASPHALT AND ABRASIVE MATERIALS BLADES - DRY - SEGMENTED RIM Used for: Asphalt, green concrete, asphalt over concrete, abrasive blocks, mortar and other abrasive materials. DUO ASPHALT BLADES Dry cutting laser welded blade for asphalt and green concrete. Laser welded drop segment wear-retardant extends blade life. Scoop gullets for faster swarf removal increases cut speed. Stroboscopic indicators to control cut depth and show rotation direction. Segment Size Part No. Max RPM Height 84543 12 x .110 x 1/20 mm 6,300 .393” 84315 14 x .125 x 1/20 mm 5,460 .393” NORTON CLASSIC BLADE Ideal blade for small to medium size high-speed cutting jobs. Economically priced with good productivity in asphalt, green concrete and other abrasive materials. NATURAL STONE & TILE BLADES - DRY - TURBO RIM GENERAL PURPOSE & MASONRY BUILDING MATERIALS BLADES - DRY - SEGMENTED RIM Ceramic and stone tiles, granite, marble, very hard bricks and other very hard and dense materials. AERO-JET BLADES Very fast, smooth cutting. The .590” high segment rim adds extremely long life whether cutting wet or dry in hard materials. Exclusive arrow shape protection inserts for precision straight cuts. A ventilated waved steel core for better cooling and intensive use. Exceptional cutting on a very wide range of materials with a high quality finished cut. Segment Size Part No. Max RPM Height 83785 14 x .125 x 1/20 mm 5,460 .472” Part No. 01231 Size Max RPM 14 x .125 x 1/20 mm 5,460 Segment Height .275” Blocks, medium-hard building bricks, paving slabs, concrete roof tiles and other medium-hard materials. VALUPLUS BLADES For value and performance on small to medium size jobs. The sintered blade cuts unreinforced soft to medium concrete fast on saws up to 13 HP. Part No. 84180 84428 Size Max RPM 12 x .110 x 1/20 mm 6,300 14 x .110 x 1/20 mm 5,460 Segment Height .393” .393” RESCUE, DEMOLITION BLADES - DRY - CONTINUOUS RIM Ductile, steel, polyvinyl pipe, thin steel plate, acrylic sheet, fiberglass, rubber, standard glass, wood, concrete, brick, asphalt. RESCUE RUNNER BLADES When seconds count, reach for the Norton Rescue Runner. The specially tempered steel core provides maximum durability under the toughest conditions on many materials. A new diamond placement technology allows diamonds to cut in both directions for quick cutting. Features: •Bidirectional Blade Usage - The symmetrical diamond pattern placement allows the quick blade mounting without worry of proper direction. •Universal Arbor - The universal arbor allows the Rescue Runner to be used on both 1” and 20 mm high-speed gas and electric saws. •Faster Cutting and Longer Life - The bonding system allows the diamond to resist premature release providing longer diamond life and speed of cut. Segment Size Part No. Max RPM Height 84426 12 x .140 x 1/20 mm 6,300 .275” 84361 14 x .140 x 1/20 mm 5,460 .275” Masonry Diamond Blades GENERAL PURPOSE & MASONRY BUILDING MATERIALS - WET - SEGMENTED RIM Blocks, medium-hard building bricks, paving slabs, concrete roof tiles and other medium-hard materials. CHARGER BLADES High performance wet cutting with an extra wide .263” segment specification that allows thorough cleaning and extended life in a variety of materials. Part No. Size Max RPM 81338 14 x .100 x 1 4,365 Segment Height .263” SP01-20 GREGG DISTRIBUTORS LTD. NORTON NRN/1546 Walk Behind Diamond Blades ASPHALT & ABRASIVE MATERIALS Asphalt, green concrete, asphalt over concrete, abrasive blocks, mortar and other abrasive materials. NORTON CLASSIC BLADES - WET - ASPHALT An economical choice for fast cutting and good life when performing jobs in a variety of abrasive materials such as green concrete and asphalt on saws up to 35 HP. Segment Size Max RPM Part No. Height 81376 18 x .125 x 1 3,395 .326” CHARGER BLADES - DRY - GREEN CONCRETE A high performance, laser welded blade designed for green concrete cutting. High quality segments produce a clean cut with reduced spalling on larger saws up to 20 HP in early entry applications. Segment Size Max RPM Part No. Height 81420 14 x .125 x 1 4,365 .263” REINFORCED CONCRETE & HARDER BUILDING MATERIALS - WET Reinforced concrete, hard bricks, limestone, terrazzo, and other hard materials CHARGER BLADES - HARD AGGREGATES High performance wet cutting hard aggregates with medium reinforcement. The increased diamond depth in the segment specification allows extended life and fast cut for medium to large jobs. Deep sawing is easily achieved on saws up to 35 HP. Part No. Size Max RPM 81471 26 x .155 x 1 2,350 NORTON CLASSIC BLADES - MEDIUM AGGREGATES Laser welded blade at an economical price for general purpose cutting of cured concrete, medium hard aggregate and no steel reinforcement. The bond and diamond combination allow fast cutting action on limited horse powered flat saws. Segment Height .410” Part No. Size Max RPM 81361 18 x .125 x 1 3,395 Segment Height .326” MULTI-PURPOSE, ALL MATERIALS - DRY - MULTI PURPOSE Concrete, reinforced concrete, granite, building materials, thin steel sections, angle iron up to 1/2” material thickness, rebar up to no. 5. 4X4 BLADES Multi-purpose laser welded blade for dry cutting a range of construction materials without sacrificing performance or price. Depth of cut is easily controlled with the patented depth-of-cut indicators cut into the steel core. Anti-crack gullets for enhanced safety cutting steel and metal (up to 5 mm thick). Part No. 84548 84547 45306 Segment Height 12 x .110 x 1/20 mm 6,300 .393” 14 x .125 x 1/20 mm 5,460 .393” 16 x .125 x 1/20 mm 4,500 .393” Size Max RPM Tile Diamond Blades NATURAL STONE & TILES - WET - CONTINUOUS RIM Ceramic and stone tiles, granite, marble, very hard bricks and other very hard and dense materials. SLICER BLADES Razor-like cut, but with high tensile strength steel core for greater accuracy and less wobbling. The bond and diamond specification enhance cutting speed and improve blade life, particularly in hard materials for premium performance. Part No. Size Max RPM 84183 84184 84185 7 x .060 x 5/8 8 x .060 x 5/8 10 x .060 x 5/8 8,730 7,640 6,115 Segment Height .393” .393” .393” NORTON CLASSIC BLADES Excellent quality with good performance in general purpose materials. The right bond and diamond content allows clean cutting with long use. Well suited for softer tile or stone materials on low horsepower tile saws. Part No. Size Max RPM 84017 02785 02784 7 x .065 x 5/8 8 x .070 x 5/8 10 x .070 x 5/8 8,730 7,640 6,115 Segment Height .393” .393” .393” www.greggdistributors.ca SP01-21 NORTON NRN/1546 Portable Hand-Held Diamond Blades GENERAL PURPOSE & MASONRY BUILDING MATERIALS Blocks, medium-hard building bricks, paving slabs, concrete roof tiles and other medium-hard materials. DUO BLADES - DRY - SEGMENTED RIM The original DUO. The innovative, exclusive design introduced in 2002 has become a dominant name in the market. The unique dual segment per land technology provides excellent cutting speed with low vibration and high comfort of cut. The exclusive arrow shape gullets not only indicate blade direction but they also assist in fast removal of cutting debris. Maximum performance when cutting hard materials and fiber cement board. Part No. 84526 84527 84129 Segment Height 4½ x .086 x 7/8-5/8-20 mm 13,300 .393” 5 x .086 x 7/8-5/8-20 mm 12,000 .393” 7 x .098 x DM-7/8-5/8 8,730 .393” Size Max RPM VALUPLUS BLADES - DRY - SEGMENTED RIM For value and performance on small to medium size jobs cutting soft abrasive materials like brick and tile. The sintered rim delivers a quality cut and good life. Part No. 84098 84099 84100 Segment Height 4 x .080 x 7/8-5/8-20 mm 15,000 .275” 4½ x .080 x 7/8-5/8-20 mm 13,300 .275” 7 x .090 x DM-7/8-5/8 8,730 .275” Size Max RPM VALUPLUS BLADES - DRY - TURBO RIM For value and performance on small to medium size jobs cutting soft brick and tile. The turbo continuous rim cuts fast with a smoother quality of cut. Part No. 84105 84106 84107 Segment Height 4 x .080 x 7/8-5/8-20 mm 15,000 .275” 4½ x .080 x 7/8-5/8-20 mm 13,300 .275” 7 x .090 x DM-7/8-5/8 8,730 .275” Size Max RPM NATURAL STONE & TILES - DRY - CONTINUOUS RIM Ceramic and stone tiles, granite, marble, very hard bricks and other very hard and dense materials. VALUPLUS BLADES A value price point for small to medium size jobs cutting standard ceramic tile with efficient cutting on low horsepower tile saws. Part No. 84088 84089 Asphalt, green concrete, asphalt over concrete, abrasive blocks, mortar and other abrasive materials. NORTON CLASSIC BLADES An economical solution for small to medium tuck pointing jobs. High quality performance for heavy grout removal or mortar jointing. The heavy duty wide segment reduces wear in abrasive materials. Segment Size Max RPM Part No. Height 81778 5 x .250 x 7/8-5/8-20 mm 12,000 .275” 81779 7 x .250 x 7/8-5/8-20 mm 8,730 .275” Segment Height 4½ x .080 x 7/8-5/8-20 mm 13,300 .275” 7 x .090 x DM-7/8-5/8 8,730 .275” Size ASPHALT & ABRASIVE MATERIALS - DRY - TUCK POINTING Max RPM REINFORCED CONCRETE & HARDER BUILDING MATERIALS - DRY - CRACK CHASING Reinforced concrete, hard bricks, limestone, terrazzo, and other hard materials. CHARGER BLADES A heavy V-shaped segment designed with a special bond and diamond content for maximum removal of grout, mortar jointing, crack chasing and crack widening. Fast cutting and long life in abrasive materials using portable tools. Highly competitive to others of its kind in the market. Part No. Size 83856 83859 4 x .375 x 7/8-5/8-20 mm 7 x .375 x 7/8-5/8-20mm Segment Height 15,000 .550” 8,730 .550” Max RPM Portable Hand-Held Diamond Cup Grinders GENERAL PURPOSE & MASONRY BUILDING MATERIALS - DRY - CUP GRINDER Blocks, medium-hard building bricks, paving slabs, concrete roof tiles and other medium-hard materials. NORTON CLASSIC BLADES Available in a range of sizes and segment designs for optimum performance by life or by speed. Ideal for levelling all types of masonry materials, brick, block, concrete and stone. Strategically placed hole designs help ventilate dust from the surface to extend the life of the cups. SP01-22 GREGG DISTRIBUTORS LTD. Part No. Size Max RPM Segment Height Single Row for Fast Stock Removal 82555 4 x 5/8”-11 15,000 .210” 84036 5 x 5/8”-11 12,225 .210” 82593 7 x 5/8”-11 8,730 .210” Double Row for Long Life, Smooth Finish 82586 4 x 5/8”-11 15,000 .210” 84038 5 x 5/8”-11 12,225 .210” 82595 7 x 5/8”-11 8,730 .210” Swirl for Most Aggressive Cut, Smooth Finish 83826 4 x 5/8”-11 15,000 .180” 84040 5 x 5/8”-11 12,225 .180” 83827 7 x 5/8”-11 8,730 .180” Turbo for Long Life, Very Smooth Finish 83830 4 x 5/8”-11 15,000 .210” 83831 7 x 5/8”-11 8,730 .210” 44801 4½” X 5/8-11 15,000 .196” 44802 7 x 5/8”-11 8,730 .196” 82586 82555 83830 83826 NORTON NRN/1546/1548 Silencio Diamond Blades SILENCIO FLAT SAW BLADE Features & Benefits: •Specially developed patent pending silent steel-center, cutting edge vibration absorbent material for noise reduction of up to 15 dB(A) than the traditional copper sandwich or laser-cut core blades •Optimized sound-dampening geometry for elimination of the whistle-effect with a blade guard during operation •A tall .590” laser welded segment results in longer blade life and faster cut •Trapezoidal segment shape has lower impacts on materials improving quality of cut similar to a continuous rim blade cut. •Smoother operating for less operator fatigue and better debris removal from cut improving blade life and free cutting •New diamond and bond specification created for masonry, flat or high speed hand saw applications is extremely fast cutting in a large variety of materials Segment Part No. Max RPM Size Height 84550 14 x .125 x 1 4365 .590” Core Bits Part No. 82778 82779 82780 82781 82782 82783 82784 82785 82786 82787 82788 82789 82790 82791 82792 82793 82794 82795 82796 MMM/4055 Size Segment Max RPM Height (inch) (mm) 1” 25 mm 4,000 .315” 1¼” 32 mm 3,000 .315” 1½” 38 mm 3,000 .315” 1¾” 44 mm 2,000 .315” 2” 51 mm 2,000 .315” 2¼” 57 mm 1,300 .315” 2½” 64 mm 1,300 .315” 3” 76 mm 1,300 .315” 3½” 89 mm 1,000 .315” 4” 102 mm 1,000 .315” 4¼” 108 mm 800 .315” 4½” 114 mm 800 .315” 5” 127 mm 800 .315” 6” 152 mm 665 .315” 7” 178 mm 600 .315” 8” 203 mm 500 .315” 10” 254 mm 400 .315” 12” 305 mm 330 .315” 14” 356 mm 285 .315” REINFORCED CONCRETE & HARDER BUILDING MATERIALS Reinforced concrete, hard bricks, limestone, terrazzo, and other hard materials. CHARGER CORE BITS Laser welded segments for faster penetration in medium aggregate with reinforcement and maximum utilization of segment life. BUSINESS/OFFICE SUPPLIES 3M Post-it® Tape •Labeling and cover-up tape •Secure yet removable •Temporary labeling •Copy blockout Part No. 658, 1” x 700” roll. FFF/2886 WHITEBOARDS Single-Sided Whiteboards Whiteboard is single-sided with galvanized backing aluminum frame, marker tray, and plastic corners. Part No. WB-1824, 18”H x 24”W. Part No. WB-2436, 24”H x 36”W. Part No. WB-3648, 36”H x 48”W. Part No. WB-4872, 48”H x 72”W. Part No. WB-4896, 48”H x 96”W. www.greggdistributors.ca SP01-23 BOSCH BSH/3023 Diagnostic Equipment ESI(truck) HD DIAGNOSTIC SCAN TOOLS Increase Shop Efficiency •Code to fix at the truck - trouble shooting information in the tool •Tech stays at the vehicle •Repair info at the truck (ie. wiring diagrams, component pictures and locations, test procedures and descriptions, and DTC look-up) •Automatic Vehicle ID Single, Intuitive Interface •Works on all trucks with a common scan tool •Intuitive, easy to use •Bluetooth wireless capability Functions Mechanics Need •Read and clear fault codes •Cylinder cut-out •Cylinder compression/balance •Injector actuations •Key component actuations •Key system tests Works with Other Software •RP1210 VCI •Compatible with industry software including most OEM’s Best Aftermarket Coverage •Truck Brands such as Freightliner, International, Kenworth, Mack, Volco, Perterbilt, Sterling, Western Star •Engine Brands such as Cummins, Caterpillar, Detroit Diesel-MBE, Volvo Mack, Navistar, PACCAR, Perkinsm Deutz, MTU •Brake Systems •Transmissions •Trailer ABS •In-Depth Heavy Duty, Medium Duty •Light Duty basic Part No. 3824, Includes ruggedized 10” tablet, RP1210 data link adapter, 6,9, and 16 pin connectors, ESI (truck) diagnostics software, and external DVD drive. Part No. 3824BSC, Includes RP1210 data link adapter, 6,9, and 16 pin connectors, and ESI (truck) diagnostics software. 3824 3824BSC DYNALINE DYN/1978 Hardware & Automotive Products GATE HOOKS SCREW HOOKS •Clear zinc plated finish Part No. Length •Clear zinc plated finish Wire Diameter 65051 2”.155 650522½” .155 650533” .176 FIFTH WHEEL KING PIN STABILIZER •Stabilizes motion of unhitched trailer or RV •Threaded hitch cap allows for height adjustment •Includes chain with inserts •Folds for storage •Durable steel construction •King pin height adjusts from 35” to 55” •5,000 lb. support capacity •5” x 5½” footplate dimension Part No. 11794. Part No. 65077 65076 65075 65073 65072 65074 65071 65070 •Suits most passenger car side mirrors •Mirror size: 7½”W x 5”H •Arm adjusts to fit mirror sizes 4”H to 6”H Part No. 17715. D C 5/64” 3/4” 15/16”1-5/16” 3/32”1-1/16” 9/32”1-11/16” 7/64”2-1/16”13/32”2-1/16” 5/32”2-1/8”11/16”3-3/8” 3/16”2-5/8”27/32”3-7/8” 3/16”2-9/16”1/2”2-9/16” 7/32” 3-3/16”1”4-7/16” 1/4” 3-1/16”1-1/32”4-5/16” 65006 65014 65017 65018 65019 65020 65024 65030 65031 B A C D C A E D D A E 0.216” 15/16” 1” 1-15/16”17/32” 0.112” 1/2” 3/8” 1-1/16”11/32” 0.190” 13/16” 5/8” 1-9/16”25/64” 0.158” 11/16” 5/8” 1-5/16”21/64” 0.138”35/64” 15/32” 1-1/8”19/64” 0.112” 1/2” 13/32”15/16” 1/4” 0.250” 1-1/8” 7/8” 1-15/16”19/64” 0.138”35/64”7/16”15/16”3/16” 0.112” 1/2” 3/8” 13/16”5/32” DUAL CLIP-ON TOWING MIRROR SP01-24 GREGG DISTRIBUTORS LTD. B •Clear zinc plated B •Suits most pickup, sports utility, and van side mirrors •Outer mirror is convex for wide angle view •Mirror size: 7½”W x 5½”H •Arm adjusts to fit mirror sizes 4½”H to 7½”H Part No. 17717. C SCREW EYES Part No. CLIP-ON TOWING MIRROR B A PRONGHORN™ PCR/3308 Electrical Products LED INDICATOR PLUGS PLUG-IN GFCI & SURGE PROTECTOR PLUG •125V 15A, 1875W Maximum •Powered Red LED Light Indicator lights up in the presence of electricity for a visual confirmation that the extension cord or outlet is functioning properly •CSA Certified, UL Listed •3 pin grounding plug and receptacle •Rugged durable design •Clear body •Pack of 2 Part No. 21-1135. •125V 15A Class A ground fault circuit interrupter •4-6 mA Trip Level with 160 joules of surge protection •Manual reset and test buttons with sealed electronics •Powered Red LED Light Indicator lights up in the presence of electricity •Automatically energizes for use upon plug-in or after power loss •CSA Certified, cULus Listed •3 pin grounding plug and receptacle •Yellow body Part No. 21-1137. PRIORITY® PCR/3259 Cylinder Storage Cabinets INDUSTRIAL STORAGE CABINETS/LOCKERS •Durable steel secured storage cabinets for forklift and combustible gas cylinders •Yellow safety finish •Designed for horizontal or vertical storage of cylinders •Cylinder storage capacity is based on cylinder size •Sides are made of expanded steel mesh, while top and bottom are made of solid sheet steel •Heavy gauge construction with heavy-duty butt hinges and padlock hasp for locking doors to secure cylinders (padlock not included) •14 gauge steel top, 1½” x 1/8” angle iron frame •Vertical units include chains for securing cylinders from falling when cabinet is shifted •Magnetic catch for keeping doors securely shut when not locked •Pre-drilled holes in support legs for securing to floor •Meets CSA, NFPA, and OSHA design standards for storage of dangerous and flammable materials •Horizontal storage cabinets accommodate 20 and 33 lb LPG cylinders and canisters •4 cylinder vertical storage cabinets accept standard vertical cylinders up to 28” high •9 and 18 vertical cylinder storage cabinets accept standard vertical cylinders up to 65” high •The 8 and 16 vertical storage cabinets can be used for either LPG cylinders or compressed gas cylinders by installing an optional shelf which is included •Includes danger signs for identifying the cabinet as containing hazardous materials •Products comes unassembled and packed for efficient shipping and storage Part No. 53-0804 53-0812 Cylinder Capacity (Uniform Size) HORIZONTAL STORAGE CABINETS/LOCKERS 53-0804 4 LPG Cylinders 53-0808 8 LPG Cylinders 53-0812 12 LPG Cylinders 53-0816 16 LPG Cylinders COMBINATION STORAGE CABINET/LOCKER 8 Horizontal LPG Cylinders and 9 Vertical 53-0820 Compressed Gas Cylinders VERTICAL STORAGE CABINETS/LOCKERS 53-0824 4 LPG Cylinders 8 LPG Cylinders or 9 Compressed Gas 53-0828 Cylinders 16 LPG Cylinders or 18 Compressed Gas 53-0836 Cylinders Overall Size (W x L x H) Shelves Net Weight 31” x 30” x 35” 31” x 30” x 72” 46” x 30” x 72” 60” x 30” x 72” 1 3 3 6 121 lbs. 184 lbs. 234 lbs. 339 lbs. 60” x 30” x 72” 3 300 lbs. 31” x 30” x 35” 0 108 lbs. 31” x 30” x 72” 1 174 lbs. 60” x 30” x 72” 2 318 lbs. 53-0824 53-0816 53-0808 53-0820 53-0836 53-0828 www.greggdistributors.ca SP01-25 AVMOR® AVM/1267/1268 Floor Care PREMIERE SUPERIOR FLOOR FINISH PREMIERE offers high gloss, superior durability, excellent detergent resistance and is well suited for low, periodic and high maintenance schedules. Premiere has outstanding gloss retention and has excellent overall wear resistance. Part No. 2086334001, 20 litre pail. W-75 FLOOR FINISH W-75 is formulated to work with any maintenance method and equipment on all types of floors. It offers good gloss characteristics along with durability making it the number one choice of schoolboards and institutions where spraybuffing maintenance schedules and budgets are restricted. W-75 offers fast drying properties so down time is at a minimum and it responds well to burnishing. Part No. 2170334001, 20 litre pail. S-22 CLEANER, DESCALER, & BRIGHTENER DYNA MIST is an outstanding waterbased treatment designed for use on mops and cloths. When sprayed lightly it creates an electrostatic action that attracts and holds airborne dust, lint, grit, and other soils. Non-flammable and non-toxic. Part No. 1101278001, 4 litre jug. Carpet Care 20/20 is a special blend of carpet cleaning chemicals. This rich concentrate contains detergents, cleaning agents, and extremely effective odour counteractants. Use 20/20 with hot water extractors to safely clean all types of carpet fibres. Part No. 2013278001, 4 litre jug. SCORPION is a powerful and fast acting floor stripper containing a blend of water soluble agents, detergents, and emulsifiers that quickly penetrates and dissolves waxers and floor finishes. SCORPION works best in cold water while excellent stripping and low odour characteristics guarantees optimum performance. Part No. 2126334001, 20 litre pail. DYNA MIST DUST MOP TREATMENT (WATERBASED) S-22 is a mild mineral-based acid formulation, which is an excellent floor cleaner for hard surfaces, non-porous floors, and tiles. Ideal for removing mineral deposits such as winter salt and calcium stains. Part No. 2002257001, 1.8 litre bottle. Part No. 2002278001, 4 litre jug. 20/20 CONCENTRATED CARPET CLEANER (EXTRACTION) SCORPION LOW ODOUR FLOOR STRIPPER ROTEX CONCENTRATED NEUTRAL CLEANER ROTEX is a one-step, neutral cleaner designed to quickly remove embedded soils without any residue, leaving the floor sparkling clean. ROTEX requires no rinsing, and leaves a summer fresh fragrance. Ideal for use with auto-scrubbers. Part No. 2001257001, 1.8 litre bottle. Part No. 2001278001, 4 litre jug. EP85 SIDEKICK RESTORER EP85 SIDEKICK is a versatile, low odour restorer designed with the newest in environmentally preferable polymer technology. It can be mopped on or applied with an autoscrubber. EP85 SIDEKICK is compatible with all Avmor floor finishes and it will accommodate both low and high maintenance schedules. EP85 SIDEKICK will restore gloss and prolong the life of the floor finish. Excellent for vinyl composition, linoleum, sheet vinyl, concrete, terrazzo, quarry, Mexican tile and most resilient type flooring. Part No. 2302278001, 4 litre jug. TRAK-5 TRAFFIC SPOTTER BYE BYE FOAM TRAK-5 is the ultimate, all-purpose spotting DEFOAMING AGENT agent. It is extremely effective on heavily soiled rugs and carpets in high traffic and other hard to clean areas. TRAK-5 loosens and breaks up stains including oil, tar, lipstick, shoe polish, grease, paint, tracked-in soil, and foods. Ideal for use on upholstery. Part No. 1391278002, 4 litre jug. BYE BYE FOAM is a concentrated defoaming formulation that reduces or eliminates unwanted or excessive foam in recovery tanks, automatic scrubbers, shampooing machines, and hot water extractors. Part No. 1388278001, 4 litre jug. EP62 CARPET & FABRIC STAIN REMOVER KLINGER PORCELAIN CLEANER ZEO ALL-PURPOSE WASHROOM CLEANER BEAU CREAM CLEANSER EP62 Carpet and Fabric Stain Remover is an aqueous solution containing a blend of biodegradable agents. This product dissolves coffee, red wine and other spots and stains, quickly and effectively. Part No. 2131210001, 946 ml bottle. Washroom Care HCL 23 PROFESSIONAL BOWL CLEANER HCL 23 is a blend of acid and surfactant working in concert to remove hard mineral deposits through chemical action. Heavy duty cleaner ideally made for weekly use to remove stains and other soil from porcelain urinals and toilet bowls. Part No. 1695210001, 946 ml bottle. KLINGER is an all-purpose, mild acid-based daily cleaner for porcelain and tiles. Its thick lotion clings to all vertical surfaces as it cleans, descales, and deodorizes in just one application. Effectively removes hard water deposits, soap scum, and urine salts. Fresh mint fragrance. Part No. 2093210001, 946 ml bottle. SP01-26 GREGG DISTRIBUTORS LTD. ZEO is a concentrated, all-purpose scrubfree washroom cleaner with strong foaming action, for fast and efficient removal of soils, such as hard water deposits and soap scum. ZEO is formulated to clean and deodorize all porcelain, tiles, and acrylic surfaces. Pleasant cherry fragrance. Part No. 2124257001, 1.8 litre bottle. Part No. 2124278001, 4 litre jug. BEAU cream cleanser is a powerful deep cleaning cream that cleans all washroom surfaces. It quickly and easily removes stubborn stains and soap scum, and contains no harsh alkalis or acids. Pleasant pine fragrance. Part No. 2127210001, 946 ml bottle. AVMOR® AVM/1267/1268 Disinfectant Cleaners BALANCE PLUS DISINFECTANT CLEANER BALANCE PLUS Cleaner Disinfectant is a phosphate free concentrated cleaner disinfectant which provides effective cleaning, deodorizing, disinfection and sanitization for use in schools, nursing homes, hospitals, food processing plants and other institutions. BALANCE PLUS is effective on walls, floors, sink tops, tables, chairs, garbage cans, telephones, bed frames and other hard, non-porous surfaces. Part No. 2089257001, 1.8 litre bottle. Part No. 2089278001, 4 litre jug. BASIX NEUTRAL pH DISINFECTANT (CONCENTRATED) BASIX, a super-concentrated disinfectant sanitizer with a neutral pH, used in health care facilities and food processing establishments. Use BASIX where superior hygiene and virucidal control are required. Effective against MRSA and VRE. Part No. 2237257001, 1.8 litre bottle. Part No. 2237278001, 4 litre jug. GERMALIN CLEANER DEGREASER DISINFECTANT LEMINEE 23 CLEANER DISINFECTANT GERMALIN is a cleaner, degreaser, and disinfectant for use in health care facilities and food processing plants. It is a quality product that gives you everything you would ever want in an all-purpose, one-step cleaner. Pleasant lemon scent. Part No. 2006278001, 4 litre jug. LEMINEE 23 is a cleaner disinfectant for use in health care facilities and food processing plants. LEMINEE 23 is very effective for controlling odours caused by the growth of bacteria. Pleasant lemon scent makes it suitable for use in all areas. Part No. 2004257001, 1.8 litre bottle. Part No. 2004278001, 4 litre jug. PINE GUARD GERMICIDAL CLEANER D.O.C. is a liquid germicide with a base of phenolic compounds, which destroy a broad range of gram-positive and gram-negative bacteria. This product can be used to clean, disinfect, deodorize, and sanitize all hard, washable environmental surfaces. Light pleasant odour makes it suitable for use in all areas. Part No. 1248278001, 4 litre jug. Foodservice Care BIOMOR MULTI-PURPOSE CLEANER BIOMOR URINAL PUCKS TIGER OVEN CLEANER SOLERA DISHWASHING LIQUID Biomor Multi Purpose Cleaner and Odour Eliminator has enzymatic activity that provides outstanding breakdown of starch, carbohydrates, fats, oils and grease. It provides an effective and environmentally friendly solution to routine cleaning. Part No. 2269257001, 1.8 litre jug. TIGER is a blend of surface active agents combined with powerful alkaline emulsifiers to penetrate baked-on grease for fast and easy clean-ups. TIGER is user friendly, since it does not produce harsh odours or fumes. Lemon fragrance. Part No. 1015780002, 510 g aerosol. Biomor Urinal Pucks are designed to provide immediate and effective odour control in urinals while inoculating the drain system with bioenzymatics. The bioenzymatics degrade the organics that cause odours and backups, making a cleaner, fresher restroom experience. Part No. 2130854001. SOLERA Dishwashing liquid is ideal for household and institutional use. SOLERA is effective on very dirty dishes, pots, and utensils. With the aid of powerful grease-cutters, SOLERA leaves dishes spotless and clean. Fresh lemon scent. Part No. 1794278001, 4 litre jug. BIOMOR HD DRAIN MAINTAINER CHEF GRIDDLE, FRYER, & OVEN CLEANER SOFT HANDS LOTION HAND SOAP ATOMIC ALL-PURPOSE CLEANER Biomor HD Drain Maintenance is a proprietary blend of surfactants and bio-cleaning agents. It provides long-term deep cleaning for drains, grease traps and odour control. HD Drain Maintenance is environmentally friendly. Part No. 2271277001, 3.78 litre jug. SOFT HANDS is an economical creamy high quality hand soap. It possesses excellent cleaning abilities, a soft texture, luxurious suds, and a refreshing cherry fragrance. Pink lotion. Part No. 2277278001, 4 litre jug. CHEF is an extremely effective cleaner for griddles, fryers, and ovens. It is a unique and proven formula for removing baked-on carbon, leaving no residue or lingering odour. Part No. 1154278004, 4 litre jug. ATOMIC All-Purpose cleaner is ideal for household and institutional use. This product may be used to clean hard surfaces, such as counters, walls, floors, doors, blinds, painted surfaces, and more. Leaves behind a fresh clean lemon scent. Part No. 2211286001, 5 litre jug. www.greggdistributors.ca SP01-27 AVMOR® AVM/1267/1268/1269 Cleaning Products BIOMOR ODOUR ELIMINATOR TORPEDO DRAIN CLEANER CITRANET LEMON & OPENER LAUNDRY DETERGENT TORPEDO is formulated using a blend of organic acids and inhibitors, which produce an immediate action to quickly melt grease, and other obstructions in drains. For professional use. Part No. 1428206003, 909 ml bottle. CITRANET is a super economical lemon laundry detergent formulated for all machine washable fabrics. Tough plastic reusable pail. Part No. 1982555020, 18.1 kg pail. EP69 GLASS & SURFACE CLEANER TROX PLUS LIQUID LAUNDRY DETERGENT BAN-O LIQUID DETERGENT 3 IN 1 DISINFECTING BAN-O eliminates unpleasant odours at the ALL-PURPOSE & GLASS source. BAN-O is an excellent deodorant CLEANER Biomor Odour Eliminator is a proprietary blend of surfactants and bio-cleaning agents. It has enzymatic activity that provides outstanding breakdown of starch, carbohydrates, fats, oils and grease. Biomor Odour Eliminator safely eliminates unpleasant odours including urine, vomit, smoke, perspiration, and food waste at the source. Part No. 2283210001, 946 ml spray bottle. EP69 Glass and Surface Cleaner dissolves, suspends, and removes soil from glass, plexiglass, windows, mirrors, windshields, walls, countertops, cabinets, partitions, light fixtures, stainless steel, chrome, plastic, vinyl, appliances, desks and other surfaces not harmed by water. EP69 leaves no residue. Part No. 2065257001, 1.8 litre bottle. TROX PLUS is a heavy duty, concentrated liquid laundry detergent, that cleans and freshens all washable fabrics. TROX is pH neutral and contains water additives for hard water performance. Part No. 2172278001, 4 litre jug. for use in washrooms, garbage cans, refuse disposal bins, lockers, changing rooms, and in places where offensive odours exist. Original fresh scent. Part No. 2000278001, 3.64 litre jug. Dispensers UNO-MIXX & DUO-MIXX DISPENSING UNITS The Uno-mixx and Duo-mixx dispensing units are an economical way to dispense a wide variety of automatically diluted solutions into spray bottles, buckets or other containers at the touch of a button. Dilution is controlled by drawing chemicals through metering tips of varying size and injecting this metered amount into the water flow. Features: •Versatile and easy to customize with any combination of Avmor products •Fittings allow for one or two products to be dispensed •Better chemical performance-consistant correct dilution •Time and labour savings-solutions are prepared accurately with reduced preparation time •Improved employee safety-eliminates splashing, spilling, and back strain Part No. 0000024113, Uno-mixx (1 high flow). Part No. 0000024441, Duo-mixx (1 high flow; 1 low flow). Part No. 0000024082, Duo-mixx (2 high flow). AV-MIXX WALL MOUNTED DILUTION CONTROL Av-mixx Wall Mounted Dilution Control System is convenient and makes cleaning easy. The system will save you money by eliminating chemical waste and can dilute multiple Av-mixx, EcoPure and Biomor chemicals. Part No. 0000023769. AV-MIXX ACCESSORIES Part No. 0000024006, Versatile storage rack for containers. Holds up to 6 Av-mixx products. SP01-28 GREGG DISTRIBUTORS LTD. AV-MIXX PORTABLE DILUTION Av-mixx Portable Dilution Control System makes cleaning even easier. The system will save you money by eliminating chemical waste and can dilute multiple Av-mixx, EcoPure and Biomor chemicals. Part No. 0000023809. KLEER WINDOW CLEANER KLEER’s unique formula leaves glass surfaces sparkling clean and streak-free. KLEER works instantly to cut through grease, smoke film, fingerprints, and grime. Economical. Part No. 2212210001, 946 ml bottle. Part No. 2212278001, 4 litre jug. 3 in 1 effectively cleans and disinfects nonporous hard surfaces of food related grease, dirt and other common soils. Ready-to-use, one step powerful disinfectant cleaner. Part No. 0294210001, 946 ml spray bottle. AVMOR® AVM/1269 Dispensers HYDROCAP CAP FOAMER For use with 4 litre containers only. Part No. 0000023912. HYDROCAP BUCKET FILL Hydrocap bucket fill offers a low cost, portable means of accurately diluting concentrated cleaning products. For use with 1.8 litre containers only. Part No. 0000023926. MULTI-MIXX Avmor’s Multi-Mixx dispensing system delivers the flexibility to dispense concentrated products and provides multiple dilution rates which can be configured for your precise needs. The pressure regulation on the Multi-Maxx system ensures accurate dilution regardless of water pressure - ensuring optimal product performance. Part No. 0000024451, EGap. MAINTENANCE ACCESSORIES Part No. 0000251985, Sprayer Regular Trigger. Part No. 0000252028, Sprayer Foaming Trigger. Part No. 0000252159, 946 ml White Bottle. Part No. 0000017197, Dosage Pump for 30 ml to 4 litres. Part No. 0000012745, Pail Pump For 1 x 20 litre Pails. Distributes 2 ml, 4 ml, 6 ml and 8 ml of product according to selection. 0000251985 0000252028 0000252159 0000012745 0000017197 PRISTINE™ PCR/3119 Tilt Trucks 1/2 & 1 YARD TILT TRUCKS •1/2 and 1 yard durable polyethylene tilt trucks •Seamless smooth ribbed plastic construction eases dumping and cleaning using rotation moulded polyethylene •Will not rust, dent, chip, peel, or absorb moisture •Powder coated full perimeter frame for load integrity with supporting dumping pivot point •Recessed wheels for wall and doorway protection •Easy to handle through commercial doorways and elevators •All wheels and castors are non-marking to protect floors •To improve portability: 1/2 yard has (2) 10” x 2-12” rubber (polyisoprene) rear wheels and (2) 3” x 1-3/8” TPR (thermoplastic rubber) swivel front casters; 1 yard has (2) 12” x 2” rubber (polyisoprene) rear wheels and (2) 4” x 2” TPU (thermoplastic polyurethane) swivel front casters •Counterbalance design for controlled and smooth dumping by one person •FDA compliant bottle material Part No. 60-6111 60-6112 60-6151 60-6152 Volume Capacity 1/2 Yard 1/2 Yard 1 Yard HD 1 Yard HD Weight Capacity 850 lbs. 850 lbs. 2,100 lbs. 2,100 lbs. Colour Black Blue Black Blue Overall Size (L x W x H) 65” x 28” x 38-5/8” 65” x 28” x 38-5/8” 77” x 34” x 44¾” 77” x 34” x 44¾” www.greggdistributors.ca SP01-29 MALLORY® MAL/2708 Snowbrush LARGE ARCTIC PLOW™ w/ SCRAPER •Super wide 16+ inch “Push-Pull” foam head clears snow quickly and won’t scratch paint •Scraper blade on opposite end for quick ice removal Part No. 18833. Extends to 51” LOCTITE® LCT/2477 Retaining Compounds 680™ RETAINING COMPOUND Slip Fit/High Strength. High strength, primerless, oil tolerant for slip-fitted parts. NSF/ANSI 61-certified, ABS, CFIA. Part No. 1835205, 10 ml bottle. Part No. 1835201, 50 ml bottle. Part No. 1835196, 250 ml bottle. CASTROL® CAS/1555 Motor Oils, Lubricants, & Fluids EDGE® MOTOR OIL with SYNTEC POWER TECHNOLOGY Castrol EDGE with SYNTEC Power Technology has a unique and proprietary formula that reduces volatility and provides superior protection for critical engine parts helping your vehicle operate efficiently at maximum power. Castrol EDGE with SYNTEC Power Technology delivers: •Power: 42% better rating on fighting power-robbing deposits •Protection: Superior engine protection against corrosive particles versus conventional and synthetic blend oils •Performance: Superior performance on deposit, wear and oxidation, meeting the toughest industry requirements Castrol EDGE with SYNTEC neutralizes acids in your engine that can cause rust and corrosion on vital engine parts such as cylinders, bearings and hydraulic valve lifters as well as providing stability and endurance under extreme conditions (heat, load, speed) that can cause conventional oils to break down. Best of all, EDGE can be used with confidence in every gasoline-engine passenger car, new or old, regardless of oil previously used. Part No. 2017-38, Grade SAE 0W20, 1 litre. PIONEER® JAR/2573 Winter Hard Hat Liners FR QUILTED LONG NECK HARD HAT LINERS 100% FR treated 5 oz. (170 gsm) woven cotton shell, shell fabric meets CGSB 155.20, 2000. Part No. 565A, FR treated brushed cotton lining, FR polyester filling, long neck with detachable mouthpiece. Part No. 564A, FR treated brushed cotton lining, FR polyester filling, no mouthpiece, helmet strap holes. Part No. 566A, 100% cotton flannel lining, FR polyester filling, detachable mouthpiece. SP01-30 GREGG DISTRIBUTORS LTD. 566A 565A 564A CAT® CLOTHING CAT/4043 Fleece Jacket MOMENTUM FLEECE JACKET A perfect mid-layer for those spring or summer mornings, the Momentum Fleece Jacket is a must-have on the jobsite. •Full front zip with storm flap •Overlays at front and back yoke, collar, elbows, side panels, bottom hem, and pocket openings •Chest pocket and lower pockets with zip closure •Chest pocket and lower pockets with zip closure •Contrast adjustable drawcord and cord locks at the bottom sides •Logo printed on front and back yoke •Wire management •Black Part No. 1313092-016-M, Medium. Part No. 1313092-016-L, Large. Part No. 1313092-016-XL, X-large. Part No. 1313092-016-2XL, 2X-large. CAT® FOOTWEAR CAT/4042 Industrial Footwear Thinsulate™ Insulation - Thinsulate™ Insulation is a light, thin and highly efficient way to keep your feet warm. Thinsulate Insulation dries quickly and breathes efficiently. Slip Resistant - Footwear with slip resistant soles reduces the risk of slips and falls - the hazard of low traction surfaces. Composite Safety Toe - CSA rated, are non-metallic, and undetectable in electronic security environments. Steel Toe - Caterpillar® steel toe boots are approved by the C.S.A. Puncture Resistant - Cat® puncture resistant footwear meets ASTM F2413-05 PR standards with a steel mid-plate designed to prevent objects form puncturing the sole. SRX - Superior grip when you need best-in-class performance slip resistant soles. HAULER 8” WATERPROOF CSA (COMP TOE) Upper: Waterproof Full Grain Leather Lining: Nylon Mesh Part No. Size Sock Liner: Nylex and PU Foam P-717628-77 Midsol: Molded PU P-717628-7.5 7½ Outsole: T1200 P-717628-8 8 Construction: Strobel/Cement P-717628-8.5 8½ Insulation: 200 gms. Thinsulate P-717628-9 9 Colour: Black P-717628-9.5 9½ P-717628-10 10 P-717628-10.5 10½ P-717628-11 11 P-717628-12 12 P-717628-13 13 MMM/1441 ENFORCE ESR CSA Upper: Full Grain Leather Lining: Nylon Mesh Sock Liner: Dual Density EVA Outsole: T963 Construction: Cement Colour: Black WOMEN’S SWITCH ST CSA Part No. Size P-718822-77 P-718822-7.5 7½ P-718822-8 8 P-718822-8.5 8½ P-718822-9 9 P-718822-9.5 9½ P-718822-10 10 P-718822-10.5 10½ P-718822-11 11 P-718822-12 12 P-718822-13 13 Upper: Nubuck with Nylon Mesh Lining: Nylon Mesh Sock Liner: Nylex and Molded EVA Midsol: EVA Outsole: T1000 Construction: Strobel/Cement Colour: Black Part No. Size P-306857-5 5 P-306857-5.5 5½ P-306857-6 6 P-306857-6.5 6½ P-306857-77 P-306857-7.5 7½ P-306857-8 8 P-306857-8.5 8½ P-306857-9 9 P-306857-9.5 9½ P-306857-10 10 3M Industrial Use Negative Pressure Respirators 3M™ SERIES 6500QL HALF FACEPIECE •Made of silicone for greater comfort and helps provide a softer feel on the face •3M Cool Flow Exhalation Valve for easy exhalation for cool, dry comfort; and designed to be long lasting •Quick Latch Drop-Down Mechanism allows easy on and off as you move in and out of contaminated areas •No need to remove your face shield when lowering or raising your respirator •Reusable Part No. 6501QL, Small. Part No. 6502QL, Medium. Part No. 6503QL, Large. www.greggdistributors.ca SP01-31 PIRIT® PIR3128 Heated Hose SERIES II HEATED HOSE •Cold Weather Water Hose •Thermostatically Controlled, turns on when temperatures are below 7.2°C (45° F), off when temperatures are above 10°C (50° F) •Pirit Hose has been tested to -41°C (-42°F) •Grounded Power Supply •Grounded Nickel Plated Brass Female and Male Coupling •Protective Bend Restrictors at both ends •Abrasion Resistant Cover •Knit Reinforcing •Heater wires are extruded directly into the hose walls for uniform heating and unrestricted water flow •Certifications: UL listed, MET approved, FDA approved materials Part No. PWL-03-12, 1/2” x 12 ft. Part No. PWL-03-25, 5/8” x 25 ft. Part No. PWL-03-50, 5/8” x 50 ft. Part No. PWL-03-100, 1/2” x 100 ft. 2” DIAMETER HEATED HOSE The PIRIT Heated Hose®: A hose that works in below-freezing temperatures. Maintain a discharge or sewage water line 24/7 throughout the winter or use for periodic tasks. •Thermostatically controlled. When plugged in the PIRIT Hose® automatically turns ON at 5.6°C (42°F) or lower and, when on, turns OFF at 14°C (57°F) or higher. •2” hose made with durable 150 psi PVC and quality aluminum cam-lock fittings. •Double-walled PVC Construction with woven outer layer for added strength. •Works with standard 110V GFCI outlet and draws only 315 watts. •Approved by MET Labs, a NRTL (Nationally Recognized Testing Laboratory) to UL (499) and CSA (C22.2 no.72 #E112826) safety standards for heated electronic appliances for outdoor use. For added safety, the PIRIT Hose® is grounded, end-to-end, including the nozzles. Part No. WID-2-25, 2” x 25 ft. PREDATOR™ PCR/3317 W4 - All Stainless Steel components (X5CrNi 1810, DIN 1.4301, AISI 304) Part No. W2 Part No. W4 Adjustment Range inches 38-150038-1600 21/32 to 3/4 38-150238-1602 3/4 to 13/16 38-150438-1604 25/32 to 7/8 38-150638-160613/16 to 29/32 38-150838-160829/32 to 31/32 38-151038-16101-1/32 to 1-3/32 38-151238-16121-5/32 to 1-7/32 38-151438-16141-3/16 to 1-5/16 38-151638-1616 1¼ to 1-3/8 38-151838-1618 1-11/32 to 1-15/32 38-152038-1620 1-13/32 to 1-17/32 38-152238-16221-1/2 to- 1-5/8 38-152438-1624 1-9/16 to 1-11/16 38-152638-1626 1-11/16 to 1-13/16 38-152838-1628 1-23/32 to 1-27/32 38-153038-1630 1-7/8 to 2 38-153238-16322-1/16 to 2-5/32 38-153438-16342-7/32 to 2-5/16 38-153638-1636 2-3/8 to 2-15/32 38-153838-16382-17/32 to 2-5/8 38-154038-16402-11/16 to 2-7/8 38-154238-16422-29/32 to 3-1/8 38-154438-1644 3 to 3-5/32 38-154638-1646 3-5/32 to 3-11/32 38-154838-16483-3/8 to 3-19/32 38-155038-16503-5/8 to 3-13/16 38-155238-1652 3-27/32 to 4-1/16 38-155438-1654 4-3/32 to 4-13/32 38-155638-1656 4-11/32 to 4-21/32 38-155838-1658 4-7/16 to 4¾ 38-156038-16604-13/16 to 5-1/8 mm 17 to 19 19 to 21 20 to 22 21 to 23 23 to 25 26 to 28 29 to 31 30 to 33 32 to 35 34 to 37 36 to 39 38 to 41 40 to 43 43 to 46 44 to 47 48 to 51 52 to 55 56 to 59 60 to 63 64 to 67 68 to 73 74 to 79 76 to 80 80 to 85 86 to 91 92 to 97 98 to 103 104 to 112 110 to 118 113 to 121 122 to 130 SP01-32 GREGG DISTRIBUTORS LTD. Band Band Width Thickness (A) 18 mm 0.6 mm 18 mm 0.6 mm 18 mm 0.6 mm 18 mm 0.6 mm 18 mm 0.6 mm 18 mm 0.6 mm 22 mm 0.8 mm 22 mm 0.8 mm 22 mm 0.8 mm 22 mm 0.8 mm 22 mm 0.8 mm 22 mm 0.8 mm 22 mm 0.8 mm 22 mm 0.8 mm 22 mm 0.8 mm 22 mm 0.8 mm 22 mm 0.8 mm 22 mm 0.8 mm 22 mm 0.8 mm 24 mm 0.8 mm 24 mm 0.8 mm 24 mm 0.8 mm 24 mm 0.8 mm 24 mm 0.8 mm 24 mm 0.8 mm 24 mm 0.8 mm 24 mm 0.8 mm 24 mm 0.8 mm 24 mm 0.8 mm 24 mm 0.8 mm 24 mm 0.8 mm Clamp Bolt Head Maximum Width Bolt Size Size Torque (B) (E) 20 mm M6*40 10 mm 10 Nm 20 mm M6*40 10 mm 10 Nm 20 mm M6*40 10 mm 10 Nm 20 mm M6*40 10 mm 10 Nm 20 mm M6*40 10 mm 10 Nm 20 mm M6*40 10 mm 10 Nm 24 mm M8*50 13 mm 13 Nm 24 mm M8*50 13 mm 13 Nm 24 mm M8*50 13 mm 13 Nm 24 mm M8*50 13 mm 13 Nm 24 mm M8*50 13 mm 13 Nm 24 mm M8*50 13 mm 13 Nm 24 mm M8*50 13 mm 13 Nm 24 mm M8*50 13 mm 13 Nm 24 mm M8*55 13 mm 13 Nm 24 mm M8*55 13 mm 16 Nm 24 mm M8*55 13 mm 16 Nm 24 mm M8*55 13 mm 16 Nm 24 mm M8*55 13 mm 16 Nm 26 mm M8*70 13 mm 30 Nm 26 mm M8*70 13 mm 30 Nm 26 mm M8*70 13 mm 30 Nm 26 mm M8*70 13 mm 30 Nm 26 mm M8*70 13 mm 30 Nm 26 mm M8*70 13 mm 30 Nm 26 mm M8*70 13 mm 30 Nm 26 mm M8*70 13 mm 30 Nm 26 mm M8*80 13 mm 30 Nm 26 mm M8*80 13 mm 30 Nm 26 mm M8*80 13 mm 30 Nm 26 mm M8*80 13 mm 30 Nm W4 W2 - Band and Band Arch: Adjustment range from 17 - 19 mm to 43 - 46 mm: Stainless steel (X5CrNi 1810, DIN 1.4301, AISI 304) Band and Band Arch: Adjustment range from 44 - 47 mm to 122 - 130 mm: Stainless steel (X8Cr17, DIN 1.4016, AISI 430) Bolt: Grade 12.9 Zinc Plated Other Components: Steel ASTM A283, Zinc Plated W2 High Tension Clamps by GROTE GRO/2426 Trailer Connectors COILED AIR ASSEMBLIES 81-0015-C-EA •Hoses are designed to withstand harsh conditions including extreme temperatures and harmful chemicals •Tightly coiled tubing provides excellent recoil memory while minimizing sagging or kinking •Working pressure of 150 psi •1/2” O.D. •Red Hose = Emergency; Blue Hose = Service •Heavy gauge steel spring provides superior cable support •Thread sealant added to all brass connectors for a leak-free seal •1/2” NPT, DOT brass fittings, standard on all models 81-0015-40C-EA Low Temperature Coiled Air •Low temperature, double-jacketed coils remain flexible in extremely cold temperatures •Operating temperature of -65°C to 104°C •Nylon Hose meets SAE J844, DOT FMVSS (49 CFR 571.106) & FMCSA (393.45) specifications •Includes a swivel fitting for the tractor-end connection •Brass handle enables a solid grip for coupling/uncoupling hoses Part No. Colour 81-0012-C-EA Red and Blue 81-0015-C-EA Red and Blue 81-0015-RC-EA Red 81-0015-BC-EA Blue 81-0015-40C-EA Red and Blue 81-0015-40RC-EA Red 81-0015-40BC-EA Blue Working Length 12 ft. 15 ft. 15 ft. 15 ft. 15 ft. 15 ft. 15 ft. Leads 6” 12” 12” 12” 12” and 40” 12” and 40” 12” and 40” Coiled Air •Nylon Hose meets SAE J844, DOT FMVSS (49 CFR 571.106) & FMCSA (393.45) specifications •Operating temperature of -40°C to 104°C •Swivel fittings included on both ends for easy hook-up Part No. Colour 81-0012-EA 81-0012-R-EA 81-0012-B-EA 81-0015-EA 81-0015-R-EA 81-0015-B-EA 81-0015-40-EA 81-0015-40R-EA 81-0015-40B-EA 81-0020-EA 81-0020-R-EA 81-0020-B-EA Red and Blue Red Blue Red and Blue Red Blue Red and Blue Red Blue Red and Blue Red Blue Working Length 12 ft. 12 ft. 12 ft. 15 ft. 15 ft. 15 ft. 15 ft. 15 ft. 15 ft. 20 ft. 20 ft. 20 ft. Leads 6” 6” 6” 12” 12” 12” 12” and 40” 12” and 40” 12” and 40” 12” 12” 12” ALUMINUM GLADHANDS – STANDARD & ANGLED •Meets or exceed SAE J318 standards •Aluminum castings with powder-coated steel clasp plates (service and emergency) •Permanent clamp screws •Polarized emergency and service gladhands •Includes a large face rubber seal •Replacement seals available in rubber or polyethylene Part No. 81-0001-EA, Universal Gladhand. Part No. 81-0001-R-EA, Emergency Gladhand, Red. Part No. 81-0001-B-EA, Service Gladhand, Blue. Part No. 81-0001-38R-EA, 38° Emergency Gladhand, Red. Part No. 81-0001-38B-EA, 38° Service Gladhand, Blue. 81-0001-38B-EA 81-0001-EA 81-0001-R-EA 81-0001-B-EA ANODIZED GLADHANDLES •Provides strain relief and prevents kinking of the air coil •Anodized coating provides superior corrosion resistance •Allows user to couple/uncouple with ease •Includes thread sealant on the male end •Sold in pairs Part No. 81-0125-PR. 81-0001-38R-EA STAINLESS STEEL FILTER SCREEN •Improved wear resistance lengthens service life •Pack of 25 Part No. 81-0115-25-PK. POWER CORD & GLADHAND SUPPORT HOLDER POGO STICKS •Provides protection and easy storage of electrical cables and air lines when not in use •High impact material designed to withstand all elements Part No. 81-0141-EA, 3 Function – 1 power cord and 2 gladhands. Part No. 81-0142-EA, 4 Function – 2 power cord and 2 gladhands. •Designed for nylon, rubber air hoses and heavy-duty ABS cables •Internal heavy duty spring •Includes a 7/16” mounting bolt, snap clip, 3 hose holder, eyebolt and nut •40” length Part No. 81-0130-EA, Chrome. Part No. 81-0131-EA, Zinc dichromate. 81-0141-EA 3.5” SNAP CLIP •Stainless steel construction •Ideal for use with a tracker bar Part No. 81-0140-EA. 81-0142-EA www.greggdistributors.ca SP01-33 BEHRINGER BEH/1377/1378 Pipe Clamps Easy to use, maintenance free. Engineering, plant, and maintenance personnel appreciate the Behringer Clamp’s rugged construction, simplicity and clean design. All systems can be quickly and effectively secured and are virtually maintenance free. Our modular clamp design assures greater flexibility in assembly, adjustment and stacking, as well as an endless variety of application configurations to suit every need. Twin Series •(*)Complete assemblies include (2) clamping halves, (1) cover plate, (1) weld plate, and (2) hex bolts Group T2 T3 T4 T5 Size Clamping Complete Clamping Cover Plates Weld Plates (inches) O.D. Assemblies* Halves T - Tube (inches) Part No. Part No. Part No. Part No. P - Pipe 1/4 x 1/4 T 3/8 x 3/8 T 1/2 x 1/2 T 1/4 x 1/4 P 5/8 x 5/8 T 3/8 x 3/8 P 3/4 x 3/4 T 1/2 x 1/2 P 7/8 x 7/8 T 1 x 1 T 3/4 x 3/4 P 1¼ x 1¼ T 1 x 1 P 1¼ x 1¼ P .250 .375 .500 .540 .625 .675 .750 .840 .875 1.00 1.05 1.25 1.32 1.66 AT2025-PPT2025-PP AT2038-PPT2038-PP AT2050-PPT2050-PP AT20540-PPT20540-PP AT2062-PPT2062-PP AT20675-PPT20675-PP AT3075-PPT3075-PP AT30840-PPT30840-PP AT3087-PPT3087-PP AT3100-PPT3100-PP AT41050-PPT41050-PP AT5125-PPT5125-PP AT51315-PPT51315-PP AT51660-PPT51660-PP TCP-T2 TCP-T2 TCP-T2 TCP-T2 TCP-T2 TCP-T2 TCP-T3 TCP-T3 TCP-T3 TCP-T3 TCP-T4 TCP-T5 TCP-T5 TCP-T5 Hex Bolts Part No. TWP-T2 TWP-T2 TWP-T2 TWP-T2 TWP-T2 TWP-T2 TWP-T3 TWP-T3 TWP-T3 TWP-T3 TWP-T4 TWP-T5 TWP-T5 TWP-T5 HEX-T2 HEX-T2 HEX-T2 HEX-T2 HEX-T2 HEX-T2 HEX-T3 HEX-T3 HEX-T3 HEX-T3 HEX-T4 HEX-T5 HEX-T5 HEX-T5 Twin Series Application: Pressures up to 1000 psi, pneumatics and low pressure hydraulics (up to 1¼” pipe). Standard Series •(*)Complete assemblies include (2) clamping halves, (1) cover plate, (1) weld plate, and (2) hex bolts Group 1 2 3 4 5 6 7 Size (inches) T - Tube P - Pipe 1/4 T 3/8 T 1/8 P 1/2 T 1/4 P 5/8 T 3/8 P 1/4 T 1/4 P 3/8 P 3/4 T 1/2 P 7/8 T 1 T 3/4 P 1-1/8 T 1¼ T 1 P 1½ T 1¼ P 1¾ T 1½ P 2 T 2¼ T 2 P 2½ P 3 T 3½ T 3 P Clamping Complete Clamping Cover Plates Weld Plates O.D. Assemblies* Halves Part No. Part No. (inches) Part No. Part No. .250 .375 .405 .500 .540 .625 .675 .250 .540 .675 .750 .840 .875 1.00 1.05 1.13 1.25 1.32 1.50 1.66 1.75 1.90 2.00 2.25 2.38 2.88 3.00 3.50 3.50 A1025-PP A1038-PP A10405-PP A2050-PP A20540-PP A2062-PP A20675-PP A3025-PP A30540-PP A30675-PP A3075-PP A30840-PP A3087-PP A3100-PP A41050-PP A41125-PP A5125-PP A51315-PP A5150-PP A51660-PP A6175-PP A61900-PP A6200-PP A7225-PP A72375-PP A72875-PP A7300-PP A7350-PP A73500-PP Stacking Bolts Part No. 1025-PP COP-1STW-1 1038-PP COP-1STW-1 10405-PPCOP-1 STW-1 2050-PP COP-2STW-2 20540-PPCOP-2 STW-2 2062-PP COP-2STW-2 20675-PPCOP-2 STW-2 3025-PP COP-3STW-3 30540-PPCOP-3 STW-3 30675-PPCOP-3 STW-3 3075-PP COP-3STW-3 30840-PPCOP-3 STW-3 3087-PP COP-3STW-3 3100-PP COP-3STW-3 41050-PPCOP-4 STW-4 41125-PPCOP-4STW-4 5125-PP COP-5STW-5 51315-PPCOP-5 STW-5 5150-PP COP-5STW-5 51660-PPCOP-5 STW-5 6175-PP COP-6STW-6 61900-PPCOP-6 STW-6 6200-PP COP-6STW-6 7225-PP COP-7STW-7 72375-PPCOP-7 STW-7 72875-PPCOP-7 STW-7 7300-PP COP-7STW-7 7350-PP COP-7STW-7 73500-PPCOP-7 STW-7 SP01-34 GREGG DISTRIBUTORS LTD. Safety Plates Hex Bolts Part No. Part No. STB-1 STB-1 STB-1 STB-2 STB-2 STB-2 STB-2 STB-3 STB-3 STB-3 STB-3 STB-3 STB-3 STB-3 STB-4 STB-4 STB-5 STB-5 STB-5 STB-5 STB-6 STB-6 STB-6 STB-7 STB-7 STB-7 STB-7 STB-7 STB-7 SAF-1 SAF-1 SAF-1 SAF-2 SAF-2 SAF-2 SAF-2 SAF-3 SAF-3 SAF-3 SAF-3 SAF-3 SAF-3 SAF-3 SAF-4 SAF-4 SAF-5 SAF-5 SAF-5 SAF-5 SAF-6 SAF-6 SAF-6 SAF-7 SAF-7 SAF-7 SAF-7 SAF-7 SAF-7 HEX-1 HEX-1 HEX-1 HEX-2 HEX-2 HEX-2 HEX-2 HEX-3 HEX-3 HEX-3 HEX-3 HEX-3 HEX-3 HEX-3 HEX-4 HEX-4 HEX-5 HEX-5 HEX-5 HEX-5 HEX-6 HEX-6 HEX-6 HEX-7 HEX-7 HEX-7 HEX-7 HEX-7 HEX-7 Clamping Halves Standard Series Application: Pressures under 1500 psi, pneumatic and low pressure hydraulic (up to 3” pipe). BEHRINGER BEH/1377/1378 Pipe Clamps Easy to use, maintenance free. Engineering, plant, and maintenance personnel appreciate the Behringer Clamp’s rugged construction, simplicity and clean design. All systems can be quickly and effectively secured and are virtually maintenance free. Our modular clamp design assures greater flexibility in assembly, adjustment and stacking, as well as an endless variety of application configurations to suit every need. Heavy Series •(*)Complete assemblies include (2) clamping halves, (1) cover plate, (1) weld plate, and (2) hex bolts Size Clamping Complete Clamping Cover Plates Weld Plates (inches) O.D. Assemblies* Halves T - Tube Part No. Part No. Part No. Part No. P - Pipe (inches) Group 1/4 T 3/8 T 1/2 T 1/4 P 5/8 T 3/8 P 3/4 T 1/2 P 1 T 3/4 P 1¼ T 1 P 1½ T 1¼ P 1¼ P 1½ P 2 P 2 T 2½ P 3 T 3½ T 4 T 4½ T 5 T 5 P 6 P H3 H4 Single Heavy Series Application: For line pressures over 1500 psi, outdoor environments, reduces pipe vibration, shock and hammer (up to 8” pipe). H5 H6 H7 H8 H9 .250 .375 .500 .540 .625 .675 .750 .840 1.00 1.05 1.25 1.32 1.50 1.66 1.66 1.90 2.38 2.00 2.88 3.00 3.50 4.00 4.50 5.00 5.56 6.63 AH3025-PP AH3038-PP AH3050-PP AH30540-PP AH3062-PP AH30675-PP AH4075-PP AH40840-PP AH4100-PP AH41050-PP AH5125-PP AH51315-PP AH5150-PP AH51660-PP AH61660-PP AH61900-PP AH62375-PP AH6200-PP AH72875-PP AH7300-PP AH7350-PP AH8400-PP AH8450-PP AH8500-PP AH95563-PP AH96625-PP Stacking Bolts Part No. Safety Plates Hex Bolts Part No. Part No. H3025-PP SCP-H3SWP-H3 STB-H3 SAF-H3 HEX-H3 H3038-PP SCP-H3SWP-H3 STB-H3 SAF-H3 HEX-H3 H3050-PP SCP-H3SWP-H3 STB-H3 SAF-H3 HEX-H3 H30540-PPSCP-H3SWP-H3 STB-H3 SAF-H3 HEX-H3 H3062-PP SCP-H3SWP-H3 STB-H3 SAF-H3 HEX-H3 H30675-PPSCP-H3SWP-H3 STB-H3 SAF-H3 HEX-H3 H4075-PP SCP-H4SWP-H4 STB-H4 SAF-H4 HEX-H4 H40840-PPSCP-H4SWP-H4 STB-H4 SAF-H4 HEX-H4 H4100-PP SCP-H4SWP-H4 STB-H4 SAF-H4 HEX-H4 H41050-PPSCP-H4SWP-H4 STB-H4 SAF-H4 HEX-H4 H5125-PP SCP-H5SWP-H5 STB-H5 SAF-H5 HEX-H5 H51315-PPSCP-H5SWP-H5 STB-H5 SAF-H5 HEX-H5 H5150-PP SCP-H5SWP-H5 STB-H5 SAF-H5 HEX-H5 H51660-PPSCP-H5SWP-H5 STB-H5 SAF-H5 HEX-H5 H61660-PPSCP-H6SWP-H6 STB-H6 SAF-H6 HEX-H6 H61900-PPSCP-H6SWP-H6 STB-H6 SAF-H6 HEX-H6 H62375-PPSCP-H6SWP-H6 STB-H6 SAF-H6 HEX-H6 H6200-PP SCP-H6SWP-H6 STB-H6 SAF-H6 HEX-H6 H72875-PPSCP-H7SWP-H7— —HEX-H7 H7300-PP SCP-H7SWP-H7— —HEX-H7 H7350-PP SCP-H7SWP-H7— —HEX-H7 H8400-PP SCP-H8SWP-H8— —HEX-H8 H8450-PP SCP-H8SWP-H8— —HEX-H8 H8500-PP SCP-H8SWP-H8— —HEX-H8 H95563-PPSCP-H9SWP-H9— —HEX-H9 H96625-PPSCP-H9SWP-H9— —HEX-H9 PROPEL™ HD PCR/3106/3107 PMS: 151C CMYK: C0 M62 Y91 K0 45% black PMS: 534C65-0115 CMYK: C100 M90 Y50 K20 Features: •Automatic valve providing overload protection •Forged steel base is welded to the cylinder shaft to ensure strength and eliminate leaks •Chrome pump piston and ram for additional rust resistance and reducing abrasion •Grab handles for carrying and positioning •Functions in upright, angled, or horizontal position •Spare seal kit included for extended life •Meets ANSI/ASME PALD 2009 and EN standards •Three piece zinc plated handle, no leak construction, high quality glide action pressure pump, hydraulic system is protected from internal damage, machined and polished cylinders, wide rugged base, heat treated saddle, and most jacks have heat treated extension screw Jack Part No. 0% black PMS: 151C 65-0123 CMYK: C0 M62 Y91 K0 45% black 65-0155 Jacks HD HYDRAULIC BOTTLE JACKS Capacity 65-0115 12 Ton 65-0117 12 Ton Low 12 Ton 65-0119 Quick Lift 65-0123 20 Ton 65-0125 20 Ton Low 20 Ton 65-0127 Quick Lift 65-0135 30 Ton 65-0155 50 Ton Minimum Height Lifting Height Adjusting Height Base Size Seal Kit Part No. 6 /16” x 4 /16” 613/16” x 411/16” 65-8115 65-8117 97/16”515/16”39/16” 79/16” x 511/16” 105/8”61/4”- 79/16” x 511/16” 73/16”33/8”19/16” 79/16” x 511/16” 65-8119 65-8123 65-8125 1013/16”611/16”23/4” 8” x 51/2” 111/16”61/4”- 715/16” x 515/16” 117/8”7” - 89/16” x 615/16” 65-8127 65-8135 65-8155 9 /8”5 /16” 615/16”33/4” 3 15 3⅛” 3” 13 11 100% black www.greggdistributors.ca SP01-35 PROPEL™ HD PCR/3106/3107 Jacks HD PNEUMATIC BOTTLE JACKS •Designed for heavy duty truck shop use, rail car, bus works, construction, mining, oil field service, mobile homes, transport and road side assistance •High performance pneumatic pump reduces lifting time •Additional manual pump feature for when there is no access to compressed air •Ductile iron base for 12 and 20 Ton, heavy duty steel base for 30 Ton and greater •Heat treated extension screw increases low height to get full use of ram •Overload and bypass safety valves prevent the jack from being used beyond its rated capacity or over extension •Self-retracting ram •Wiper seals protect hydraulic system from debris and contaminants •Long air line and air valve with integrated filter for remote use and protection from contaminants •High tenacity o-ring to reduce wear and double cylinder cleaning •Grab handles for carrying and positioning •Meets ANSI/ASME PALD 2009 and EN standard Jack Part No. 65-0312 65-0320 65-0335 65-0350 Capacity 12 Ton 20 Ton 35 Ton 50 Ton Minimum Height Adjusting Height Lifting Height 101/4”913/16”33/16” 105/16”95/8”35/16” 107/16”57/8”- 121/16”7” - Base Size 73/4” x 51/4” 83/4” x 67/16” 87/8” x 77/8” 107/8” x 73/8” 65-0335 Seal Kit Part No. 65-0350 65-8312 65-8320 65-8335 65-8350 HD JACK STANDS •High quality heavy-duty construction •Durable backed enamel finish to resist corrosion •Pin-type support column adjusts to multiple height positions •Adjustment pin is secured to stand to prevent loss •Large support saddle with locating lugs to position and centre load •#65-0405 meets ANSI/ASME PALD 2009 and EN standard •#65-0510 and 65-0512 meets ANSI/ASME PALD 2005 and EN standard Jack Part No. Capacity Sold as 65-0405 5 Ton Pair 65-0510 10 Ton Each 65-0512 12 Ton Each Style Pin Pin Pin Minimum Height Maximum Height 10½” 16½” 283/8”467/8” 3111/16” 47¾” HD LONG FLOOR JACKS •Designed for heavy-duty lifting applications, including bus and truck fleets, agriculture, industrial, and heavy construction equipment requiring access to very low hard to reach places •Long 59” body for easier lifting of vehicle with long overhangs •Foot operated pump for quick lifting •Automatic safety overload valves •Swivel casters for maneuverability •Handle mounted control lever to lock handle in 1 of 3 positions •High tenacity o-ring to reduce wear •Treated cylinder inner wall for durability and impact resistance •Thick lifting rod and large wheels for long lasting strength and durability •Meets ANSI/ASME PALD 2009 and EN standard Part No. Capacity Lifting Range 65-0717 65-0725 5 Ton 10 Ton 57/8” to 22” 61/4” to 22” Seal Kit Part No. 65-8717 65-8725 HD AIR/HYDRAULIC FLOOR JACKS •Designed for heavy-duty lifting applications, including bus and truck fleets, agriculture, industrial, and heavy construction equipment •Long “T” handle assists in positioning jack •Load release on top of handle is operable in any handle position •Handle can be secured in either vertical, horizontal or 45° position •Compact design fits easily between tandem wheels •Large wheels for maneuverability •Self retracting ram •Automatic safety overload valves and safety bypass •High tenacity O-ring to reduce wear •Treated cylinder inner wall for durability and impact resistance •Fast lifting air motor •Special treatment on cylinder for durability •Meets ANSI/ASME PALD 2009 and EN standard Part No. Capacity 65-0752 65-0765 65-0780 65-0785* 22 Ton 35 Ton 50 Ton 35/22 Ton Lifting Range 8-7/8” to 17-11/16” 10-1/8” to 21-1/8” 11-7/16” to 21¼” 8½” to 19¾” HD AIR/HYDRAULIC LONG FLOOR JACKS •Designed for heavy-duty lifting applications, including bus and truck fleets, agriculture, industrial, and heavy construction equipment requiring access to very low hard to reach places •Long 59” body for easier lifting of vehicle with long overhangs •Foot operated pump for quick lifting •Automatic safety overload valves •Swivel casters for maneuverability •Handle mounted control lever to lock handle in 1 of 3 positions •High tenacity O-ring to reduce wear •Treated cylinder inner wall for durability and impact resistance •Thick lifting rod and large wheels for long lasting strength and durability •Can be operated manually when air is not available •Meets ANSI/ASME PALD 2009 and EN standard Part No. Capacity Lifting Range 65-0735 65-0740 5 Ton 10 Ton 57/8” to 22” 61/4” to 22” Seal Kit Part No. 65-8735 65-8740 HD LOW PROFILE TRANSMISSION JACKS •Forged base •Chromed pump piston and ram for additional rust resistance and abrasion reduction •PU wheel for durability •Meets ANSI/ASME PALD 2009 and EN standard Part No. Capacity Lifting Range Seal Kit Part No. 65-0807 65-0810 65-0815 1/2 Ton 1 Ton 1-1/2 Ton 7½” to 29¾” 6-7/8” to 35¼” 8¾” to 37” 65-8807 65-8810 65-8815 Seal Kit Part No. 65-8752 65-8765 65-8780 65-8785 *35/22 Ton Two Stage has a forged base for enhanced durability 65-0807 65-0815 PMS: 151C CMYK: C0 M6 45% black SP01-36 GREGG DISTRIBUTORS LTD. PMS: 534C CMYK: C100 PROPEL™ HD PCR/3106/3107 Jacks HD HIGH LIFT TRANSMISSION JACKS PMS: 151C CMYK: C0 M62 Y91 K0 •Wide leg base with swivel wheels •Fully adjustable universal saddle •Foot operated hydraulic pump for easy control of positioning or removing transmission •High tenacity O-ring •Double acting cleaning seals •Meets ANSI/ASME PALD 2009 and EN standard 45% black PMS: 534C CMYK: C100 M90 Y50 K20 PMS: 151C CMYK: C0 M62 Y91 K0 Capacity 65-0827 65-0830* 65-0835 1/2 Ton 1/2 Ton 1 Ton *Pnemuatic 0% black 65-0830 Part No. 37-5/8” to 76½” 32¾” to 71½” 33-7/8” to 72-11/16” Cranes & Engine Stands 45% black •Deliver the lifting ability you need with the combined advantage of compact storage •Double bearing swivel casters provide smooth and easy maneuvering around the work place •Includes ram, chain, and hook 100% black 65-8827 65-8830 65-8835 Part No. 65-0850, Saddle for #65-0830 and 65-0835. 65-0835 FOLDABLE ENGINE CRANES Seal Kit Part No. Lifting Range HD FOLDABLE ENGINE CRANES HD ENGINE STAND •Heavy-duty welded construction with rugged reinforced tubular steel •Large caster wheels •Large capacity with 3 positions •Special square base frame resulting in a stable working stance •Unique quick-lift technology by double action pump •Chrome plated lifting piston and pump plunger •Special hydraulic rams equipped with a built-in bypass mechanism •Folds up to save space •Meets ANSI/ASME PALD 2005 and EN standard •Folding •Meets ANSI/ASME PALD 2005 and EN standard Part No. 65-1140, 2,000 lbs. capacity. Part No. 65-1112, 1,250 lb. capacity. PMS: 534C CMYK: C100 M90 Y50 K20 Part No. 65-1005 65-1011 Capacity Lifting Range Seal Kit Replacement Ram Boom Extends Part No. Part No. 1 Ton 1-1/8” to 82-3/16” 20-7/8” to 35” 65-900565-9414 2 Ton 0” to 92” 25¼” to 46½” 65-901165-9420 Part No. 65-1010 65-1012 Seal Kit Replacement Ram Capacity Lifting Range Part No. Part No. 1 Ton 2 Ton 0” to 96½” 65-901065-9410 0” to 98” 65-901265-9412 100% black Portable Hydraulic Equipment •Contains hydraulic equipment needed for lifting, pushing, pulling, bending, straightening, and spreading •Perfect for the auto body, frame repair, and construction industry Features: •”Quick-Lock” design for fast and easy assembly and disassembly •Thicker walled extension tubes for added strength and longer life •Blow molded case •Meets ANSI/ASME PALD 2009 and EN standard HD 4 TON PORTABLE RAM HYDRAULIC EQUIPMENT KIT •Includes: storage case, hydraulic pump, hose, ram flat base, 4”, 8”, 12”, and 16” extension tubes, 1/2 ton spreader, single acting ram with 4” stroke, tube coupling, ram toe, wedge head, serrated saddle, flex head, plunger toe, and 90° wedge head •Min Ram Height: 10-5/8”; Ram Lifting Height: 5” Part No. 65-1205. REPLACEMENT PARTS Part No. 65-9205, Seal Kit. Part No. 65-9801, 4” Extension Tube. Part No. 65-9802, 8” Extension Tube. Part No. 65-9803, 12” Extension Tube. Part No. 65-9804, 16” Extension Tube. Part No. 65-9805, Ram Flat Base. Part No. 65-9806, Ram Toe. Part No. 65-9807, Plunger Toe. Part No. 65-9808, Wedge Head. Part No. 65-9809, 90° Wedge Head. Part No. 65-9810, Tube Coupling. Part No. 65-9811, Serrated Saddle. Part No. 65-9812, Flex Head. Part No. 65-9813, 1/2 Ton Spreader. Part No. 65-9814, Single Acting Ram with 4” Stroke. Part No. 65-9815, Hydraulic Pump. Part No. 65-9816, Hose End Coupler. Part No. 65-9817, Ram End Coupler. Part No. 65-9818, 5 ft. Hose. Part No. 65-9819, Storage Case. HD 10 TON PORTABLE RAM HYDRAULIC EQUIPMENT KIT •Includes: storage case with wheels, hydraulic pump, hose, ram flat base, 5”, 10”, 14”, and 19” extension tubes, 1/2 ton spreader, single acting ram with 6” stroke, tube coupling, ram toe, wedge head, serrated saddle, flex head, plunger toe, and 90° wedge head •Min Ram Height: 14-1/8”; Ram Lifting Height: 5-5/16” Part No. 65-1211. REPLACEMENT PARTS Part No. 65-9211, Seal Kit. Part No. 65-9851, 5” Extension Tube. Part No. 65-9852, 10” Extension Tube. Part No. 65-9853, 14” Extension Tube. Part No. 65-9854, 19” Extension Tube. Part No. 65-9855, Ram Flat Base. Part No. 65-9856, Ram Toe. Part No. 65-9857, Plunger Toe. Part No. 65-9858, Wedge Head. Part No. 65-9859, 90° Wedge Head. Part No. 65-9860, Tube Coupling. Part No. 65-9861, Serrated Saddle. Part No. 65-9862, Flex Head. Part No. 65-9864, Single Acting Ram with 6” Stroke. Part No. 65-9865, Hydraulic Pump. Part No. 65-9816, Hose End Coupler. Part No. 65-9817, Ram End Coupler. Part No. 65-9818, 5 ft. Hose. Part No. 65-9869, Storage Case with Wheels. www.greggdistributors.ca SP01-37 PROPEL™ HD PCR/3106/3107 Miscellaneous Equipment HD TRUCK RAMPS 4½ Ton Features: •Detachable ramp from base for accessibility 20 Ton Features: •Stow away retractable handles and wheels for maneuverability •Meets ANSI/ASME PALD 2005 and EN standard Capacity Width Sold as 65-20174½ Ton 65-2020 20 Ton Part No. 9” 16” Pair Each 1,250 LB. WHEEL DOLLY •1,250 lb. capacity, lifts tires up to 10” wide •Ratcheting foot pedal for hands-free use •Rugged steel construction •Heavy-duty 3½” ball bearing swivel casters •Folds flat for easy storage Part No. 65-2005. Part No. 65-9110, Seal Kit. PMS: 151C 65-2017 CMYK: C0 M62 Y91 K0 45% black 65-2020 PMS: 534C CMYK: C100 M90 Y50 K20 Shop Presses Features: •Ideal for automotive, truck, fleet, and industrial repair shops •Heavy-duty welded construction •Double speed •Supplied with a full set of pressing pins with a purpose made tool shelf •V-blocks included •Meets ANSI/ASME PALD 2009 and EN standard HD 15 TON HYDRAULIC SHOP PRESS •Ram Stroke: 6¼” •Side Stroke: 6¼” •Working Range: 5-7/8” to 18” •Bed Width: 19-11/16” •Overall Size: 27½” x 21¼” x 38” •Manually operated double speed pump Part No. 65-1315. Part No. 65-9215, Seal Kit. HD 20 TON HYDRAULIC SHOP PRESS 0% black •Ram Stroke: 7¼” •Side Stroke: 6-15/16” 151C •Working Range:PMS: 1-7/16” to 36⅛” CMYK: C0 M62 Y91 K0 •Bed Width: 20-1/16” •Overall Size: 28¾” x 22” x 64” 45% black •Manually operated double speed foot and hand pump Part No. 65-1320. Part No. 65-9220, Seal Kit. Part No. 65-1323, Grid Guard, 20¼” x 20½”. HD 30 TON HYDRAULIC SHOP PRESS •Ram Stroke: 5-15/16” •Side Stroke: 7-7/8” •Working Range: 5-15/16” to 40-5/8” •Bed Width: 21-1/16” •Overall Size: 31¼” x 27½” x 72” •Manually operated double speed foot and hand pump Part No. 65-1330. Part No. 65-9230, Seal Kit. Part No. 65-1333, Grid Guard, 19-1/16” x 20½”. HD 50 TON HYDRAULIC SHOP PRESS •Ram Stroke: 7-7/8” •Side Stroke: 9-5/8” •Working Range: 2-11/16” to 41¼” •Bed Width: 28¾” •Overall Size: 40½” x 31½” x 73” •Press bed is raised and lowered by hand winch •Manually operated double speed foot and hand pump Part No. 65-1350. Part No. 65-9250, Seal Kit. Part No. 65-1353, Grid Guard, 26½” x 24-5/8”. 100% black 8 PC. HD PRESS PIN SET HD 50 TON AIR/HYDRAULIC SHOP PRESS •Ram Stroke: 7-7/8” •Side Stroke: 9-5/8” •Working Range: 2-11/16” to 41¼” •Bed Width: 28¾” •Overall Size: 40½” x 31½” x 73” •Press bed is raised and lowered by hand winch Part No. 65-1355. Part No. 65-9255, Seal Kit. Part No. 65-1353, Grid Guard, 26½” x 24-5/8”. CROSBY PMS: 534C CMYK: C100 M90 Y50 K20 •Full set of pressing pins with purpose made tool shelf and adapter •Fits all presses •Pin details: -2 Ton: 3/8” x 1” x 2” -3 Ton: 1/2” x 1” x 2-3/8” -8 Ton: 5/8” x 1” x 2-3/8” -12 Ton: 11/16” x 1” x 3-11/32” -14 Ton: 25/32” x 1” x 3-11/32” -16 Ton: 7/8” x 1” x 3-11/32” -18 Ton: 1” x 1” x 4-11/32” -20 Ton: 1-3/16” x 1” x 4-11/32” Part No. 65-1327. CFT/1725 Fittings Hoist 100% black Rings S-264 PAD EYES S-265 WELD-ON PIVOT LINK •(*) Meets the requirements of military Specification MS-51930A Part No. 1090722*, Size 0. Part No. 1090740*, Size 1. Part No. 1090768*, Size 1½. Part No. 1090786, Size 2. Part No. 1090802, Size 4. Part No. 1090820, Size 5. SP01-38 GREGG DISTRIBUTORS LTD. Part No. Working Load Limit (t) Design Factor Design Factor 4:1 5:1 12907401.2 12907683.2 12907865.3 12908028.0 129082015.0 1.0 2.5 4.2 6.4 12.0 FLUKE FLK/2268 True-RMS Digital Multimeters UTILITY MULTIMETER •VCHEK™ LoZ low impedance measurement function to simultaneously test for voltage or continuity •True-RMS for accurate AC measurements on non-linear loads •A large backlit display allows for easy visibility in low-lit areas •Record signal fluctuations using the Min/Max function •Diode test for testing general-purpose germanium, silicon, and power diodes •Integral holster with probe holders for easy storage •Auto and Manual ranging for added user functionality •Meets Measurement Category CAT III 600 V and Category IV 300 V standards for a higher level of safety Part No. 113. REMOTE DISPLAY MULTIMETER •True-RMS AC voltage and current for accurate measurements on non-linear signals •Measure up to 1000 V AC and DC •Measure up to 10 A (20 A for 30 seconds) •10,000 μF capacitance range •Frequency to 50 kHz •Built in thermometer conveniently allows you to take temperature readings without having to carry a separate instrument •Resistance, continuity and diode test •Low power wireless technology allows the display to be carried up to 10 meters (33 ft) away from the point of measurement for added flexibility. No interference with measurements •The removable magnetic display can be conveniently mounted where it is easily seen •Make measurements without holding the meter to improve visual focus on probes and augment safe electrical measurements •Use as a conventional multimeter when the display is connected •Radio transmitter automatically turns off when the display is connected to the meter •Auto power off maximizes battery life •Min/Max and Average recording to capture variations automatically •Test continuity and diodes •Easy to read display with large digits and bright backlight •Battery life approximately 400 hours Part No. 233. INSULATION MULTIMETER The Fluke 1577 Insulation Multimeter combines a digital insulation tester with a full-featured, True-RMS digital multimeter in a single compact, handheld unit, which provides maximum versatility for both troubleshooting and preventative maintenance. Like other tools that you have come to expect from Fluke, the 1577 is rugged, reliable, and easy to use. Whether you work on motors, generators, cables, or switch-gear, the Fluke 1577 Insulation Multimeter is ideally suited to help you with your tasks. Includes: remote probe, test leads, alligator clips, hard case, and user documentation. Part No. 1577. RUGGED IP67 INDUSTRIAL MULTIMETER Fluke 27 II and Fluke 28 II digital multimeters define a new standard for operating in harsh conditions with the features and accuracy to troubleshoot most electrical problems. Both meters have IP 67 (waterproof and dustproof) rating, MSHA approvals, extended operating temperature range of -15°C to 55°C (-40°C for up to 20 minutes) and 95 % humidity, and have been designed and tested to withstand a 3 m (10 ft) drop. The new Fluke 20 Series Multimeters are built to work in the toughest environments. Includes: test leads, alligator clips, temperature probe (28 II), holster, manual, CD-ROM, three AA batteries. Part No. 27-II. Part No. 28-II, TRMS Version. ELECTRICAL MULTIMETER Designed by electricians. Engineered by Fluke. Compact True-RMS meter for electrical troubleshooting. The Fluke 114 is a battery-powered, True-RMS multimeter the perfect troubleshooting tool for “go/no-go” testing. It includes a feature to prevent false readings caused by ghost voltage Part No. 114/EFSP. ELECTRONICS LOGGING MULTIMETER with TRENDCAPTURE •Compatible with Fluke Connect mobile app and all Fluke FC enabled test tools with optional ir3000 FC infrared connector (sold separately) •TrendCapture quickly graphically displays logged data session to quickly determine whether anomalies may have occurred •Zoom on trend provides unprecedented ability to view and analyze TrendCapture data; zoom in up to 14 times •Selectable AC filter (smoothing mode) helps display a steadier reading when the input signal is changing rapidly or noisy •Adjustable recording and auto hold thresholds, specify a percentage change in the readings that begins a new event •Large 50,000 count, 1/4 VGA display with white backlight •Logging function with expanded memory for unattended monitoring of signals over time •On board help screens for measurement functions •Saved measurements allow you to name and recall measurements made in the field •Multi-lingual interface •Multiple logging sessions possible without download •0.025 % basic DC accuracy •100 kHz ac bandwidth •Real time clock for automatic time stamping of saved readings •True-RMS AC voltage and current for accurate measurements on complex signals or non-linear loads. AC bandwidth specified to 100 kHz. •Measure up to 10 A (20 A for 30 seconds) •100 mF capacitance range •Temperature function •Relative mode to remove test lead resistance from low ohms or capacitance measurements •Peak capture to record transients as fast as 250 μs •Premium test leads and alligator clips and amp jack plugs included Includes: •Fluke 287 True-RMS Electronics Logging Multimeter •TL71 Test Leads •AC175 Alligator Clips •Batteries – 6 AA Installed Part No. 287. INTRINSICALLY SAFE DIGITAL MULTIMETER Now there’s one intrinsically safe digital multimeter (DMM) you can use in IIC (gas), in Zone 1 and 2 and IIIC (dust), Zone 21 and 22. Whether you work in petroleum, chemical, or pharmaceutical environments, all the test and troubleshooting power you need is packed into the most rugged intrinsically safe (IS) DMM Fluke has ever built. The Fluke 28 II Ex is also waterproof, dust-proof and drop-proof. You’ll be equipped to handle any situation, inside and outside of hazardous zones, without compromising compliance or measurement performance. IP67. Part No. 28IIEX/ETL . Digital Multimeters 77-IV DIGITAL MULTIMETER The Fluke 77-IV digital multimeter has the features needed to repair most electrical and electronic problems. This meter is simple to use and has significant improvements with more measurement functions, conformance to the latest safety standards, and a much larger display that’s easier to view. The Fluke Model 77-IV is a battery-powered, average responding-RMS indicating multimeter, with a 6000-count, 3 3/4-digit display, and a bar graph. Measures: •AC / DC voltage & current •Wide 1000 V measurement range •Average responding AC measurements •0.3% accuracy •10 Amps continuous (20A for 30 seconds) •Frequency and capacitance •Resistance and continuity •Diodes This multimeter meets the CAT III and CAT IV IEC 61010 standards. Includes: •Fluke TL75 test leads •9 V battery (installed) •Manual Part No. 77-4. www.greggdistributors.ca SP01-39 FLUKE FLK/2268 Digital Multimeters 83V INDUSTRIAL MULTIMETER The Fluke 83-5 offers accuracy and diagnostics for industrial maintenance in the tool box or on the bench. The new Fluke 83-5 has improved measurement functions, trouble-shooting features, resolution and accuracy to solve more problems on motor drives, in plant automation, power distribution and electro-mechanical equipment. Part No. 83-5. 5.5 DIGIT RESOLUTION DIGITAL MULTIMETER The Fluke 8808A multimeter has a broad range of functions, measuring volts, ohms and amps with a basic V dc accuracy of 0.01 %. It is remarkably easy to use, even by unskilled operators, because it makes the measurements you perform most often extremely easy and fast to do. Six setup buttons on the Fluke 8808A front panel operate like a car radio’s station presets. Simply set up the meter for a common measurement, then press shift followed by a setup button (S1 to S6) to save the setup. Now each time you perform that measurement, you simply press the appropriate setup key. It’s that easy! The setup buttons eliminate the need to follow complex work instruction sheets. Operators no longer need to press multiple buttons to set up a measurement function and range, test limits, or enter other parameters to make a measurement. Part No. 8808A. ELECTRICIAN’S MULTIMETER & VOLTAGE TESTER COMBO KIT All your electrical troubleshooting tools in one package. •179 True-RMS Digital Multimeter •1AC-II VoltAlert Non-Contact Voltage Tester •K-type temperature probe •Retractable long reach alligator clips •Sharp 12 mm stainless steel tip provides reliable contact •.5m silicone leads resist heat •ToolPak meter hanging accessory to hold meter to steel surfaces •Lightweight soft case to provide optimal protection and storage Part No. 179/1AC-II. BENCH TOP 6.5 DIGIT PRECISION MULTIMETER The Fluke 8845A Bench Top 6.5 digit Precision Multimeter has the precision and versatility to handle your most demanding measurements, on the bench or in a system. These meters are both high performance and feature rich, yet also remarkably easy to use. The Fluke 8845A Bench Top 6.5 digit Precision Multimeter performs the functions you would expect to see in a multifunction DMM, including measuring volts, ohms, and amps. Basic V dc accuracy of up to 0.0024%, 10 A current range, and a wide ohms range give you an unbeatable combination of measurement capability. You can also use the the Fluke 8845A Bench Top 6.5 digit Precision Multimeter to measure frequency and period. The functions of a counter, capacitance meter, and thermometer are built in for unparalleled versatility. Extend the meters’ utility even more with their graphical display modes, including Trendplot paperless recorder mode, statistics and histograms-features you won’t find on other multimeters. Part No. 8845A. INDUSTRIAL MULTIMETER & INFRARED THERMOMETER COMBO KIT Combo Kit includes: •179 True-RMS Digital Multimeter •80BK K-type temperature probe •Hard Point Test Lead Set •Hard Meter and Accessory Case Part No. 179/61-KIT. ELECTRONIC’S MULTIMETER & DELUXE ACCESSORY COMBO KIT Combo Kit includes: •179 True-RMS Digital Multimeter •K-type temperature probe •SureGrip Heavy Duty Hook Clips •Electronic Test Probes •SureGrip Silicone Test Leads resist heat •ToolPak meter hanging accessory to hold meter to steel surfaces •Lightweight soft case to provide optimal protection and storage Part No. 179/EDA2. 287 FlukeView® FORMS COMBO KIT Combo Kit includes: •287 True-RMS Electronics Logging Multimeter •FlukeView® Forms Software with cable •Thermocouple Probe •Test Leads with model 175 modular probe tips •Medium alligator clips •Probe caps •Soft Case •Batteries – 6 AA Installed •CD User Manual Part No. 287/FVF. SP01-40 GREGG DISTRIBUTORS LTD. 289 FlukeView® FORMS COMBO KIT Combo Kit includes: •289 True-RMS Industrial Logging Multimeter with TrendCapture •FlukeView Forms Software and cable •Integrated DMM thermocouple probe •Silicone Test Lead Set •Alligator Clips •Magnetic Meter Hanger •Durable and lightweight Soft Case Part No. 289/FVF. DIGITAL MULTIMETER with I400 CURRENT CLAMP COMBO KIT Combo Kit includes: •289V Advanced data logging Multimeter •i400 AC 400A Current Clamp •Silicone Test Leads •Alligator Clips Part No. 289/IMSK. FLUKE FLK/2268 Digital Multimeters DIGITAL MULTIMETER with FLUKE i400 CURRENT CLAMP COMBO KIT Combo Kit includes: •87V Multimeter with temperature frequency, capacitance 250 μs peak minmax •i400 AC 400A Current Clamp •Thermocouple bead probe •Test leads •Alligator Clips Part No. 87V/IMSK. True-RMS Clamp Meters CLAMP METER Measurement capability: •400A AC current measurement •600 V AC and DC voltage measurement •True-RMS AC voltage and current for accurate measurements on non-linear signals •Resistance measurement up to 4 kΩ with continuity detection •Temperature and capacitance measurement Features: •Slim, ergonomic design •Large, easy to read backlight display •CAT IV 300V/CAT III 600 V safety rating •Hold button •Soft carrying case Includes: •Test leads •Soft case •User’s manual Part No. 324. 2000 A CLAMP METERS •Reliably handle a wide range of highcurrent applications with 2000 A ac + dc True-RMS, 1400 A AC, and 2000 A DC •The large 58 mm (2.3”) jaw capacity is suitable for large or multiple conductors •CAT IV 600 V, CAT III 1000 V rating for added user protection •In-rush current measurement captures ‘power-on’ surge current with accuracy and repeatability •Accurately measure frequency up to 1 kHz for optimum troubleshooting •Quickly analyze readings using the MIN, MAX, and AVG functions •A large backlit display allows for easy visibility in low-lit areas •Use the display hold feature to capture readings even when the display cannot be viewed •Use the low-pass filter to smooth out noisy loads and stabilize readings #355 Features: High voltage measurement of 1000 V AC + DC True-RMS, 600 V AC, and 1000 V DC allows the user to perform multiple tests with only one tool. Resistance to 400K ohms coupled with a continuity beeper provide the convenience of a multimeter in a clamp meter. #355 Includes: •355 clamp meter •C43 Soft carrying case •6 AA batteries •TL224 1.5 m silicone rubber test leads •TP2 Test Probes •AC285 Alligator Clips •User manual #353 Includes: •353 clamp meter •C43 Soft carrying case •6 AA batteries •User manual Part No. 353, Amps only. Part No. 355. DETACHABLE JAW AC/DC CLAMP METER •200 A AC and DC current measurement with detachable jaw •600 V AC and DC voltage measurement •Detachable jaw makes accessing wires and viewing the display easier •Built in flashlight/torch allows for easy illumination and identification of wires •CAT III 600 V •Compact design fits in your hand and can be used while wearing protective equipment •State of the art signal processing allows for use in noisy electrical environments while providing stable readings •Large, easy to read, backlight display automatically sets the correct measurement range so you do not need to change switch positions while taking a measurement •Soft carrying case •Safety conformance: IEC/EN 61010-1:2001, CAT III 600 V Includes: •Coated instruction card •Safety information sheet •Soft carrying case •TL75 test leads •Magnetic hanging strap •Five AA Alkaline batteries Part No. 365. Clamp Meters EARTH GROUND CLAMP METER •A wide ground loop resistance range, from 0.025 Ω to 1500 Ω, to satisfy all requirements •Large jaw opening of 35 mm (1.38 in) for tests on ground conductors and/or equipotential bus bars •Measurement of ground leakage current, from 0.2 mA to 1000 mA, without needing to disconnect - ideal for system troubleshooting •Wide AC current measurement range from 0.2 A to 30 A allows one instrument for multiple applications •User-defined HI / LO Alarm limits, for rapid measurement evaluation •Handy ‘display hold’ button for capturing readings in hard-to-reach places •Time saving memory function automatically records and stores measured values •Automatic self calibration ensures correct measurement every time •Overload protection: 200 A •Carrying case and resistance test loop included •≥ 8 hours battery life (continuous operation) Includes: •Rugged carrying case with shoulder strap •Resistance test loop •9 V battery •User’s manual Part No. 1630. i1010 AC/DC CURRENT CLAMP Fluke current clamps extend the current ranges of Fluke tools. The Fluke i1010 AC/DC current clamp is highly reliable, measures 1A to 1000A and provides accurate current reading without breaking the circuit. This clamp measures both AC and DC current with a large jaw, battery-powered Hall-effect probe that gives access to difficult to reach areas. Compatible with most Fluke multimeters. Part No. I1010. i30 AC/DC CURRENT CLAMP The i30 current clamp is based on Hall Effect technology for use in measurement of both DC and AC current. Part No. I30, The i30 may be used in conjunction with multimeters, recorders and other suitable recording instruments for accurate non-intrusive current measurement. Part No. I30S, The i30s may be used in conjunction with oscilloscopes and other suitable recording instruments for accurate non-intrusive current measurement. Part No. I310S, The i310s may be used in conjunction with oscilloscopes and other suitable recording instruments for accurate non-intrusive current measurement. www.greggdistributors.ca SP01-41 FLUKE FLK/2268 Testers INSULATION RESISTANCE TESTERS •Repetitive or hard-to-reach testing is easy with the remote test probe •Live circuit detection prevents insulation test if voltage > 30 V is detected for added user protection •Auto-discharge of capacitive voltage for added user protection •AC/DC voltage: 0.1 V to 600 V •200 mA Continuity •Resistance: 0.01 Ω to 20.00 kΩ •Save battery power with auto power off •Read measurements easily with large, backlit display •CAT IV 600 V over voltage category rating for added user protection •Remote probe, test leads, probes and alligator clips included with each tester •Save both time and money with Automatic calculation of Polarization Index and Dielectric Absorption Ratio (only available on the #1507) •Make repetitive tests simple and easy with the #1507’s Compare (Pass/Fail) function (only available on the #1507) Includes: •Remote probe •Test leads •Test probes •Alligator clips •User documentation Part No. 1507, Insulation test range: 0.01 MΩ to 10 GΩ and Insulation test voltages: 50 V, 100 V, 250 V, 500 V, 1000 V. Part No. 1503, Insulation test range: 0.1 MΩ to 2000 MΩ and Insulation test voltages: 500 V, 1000 V. Part No. 1503/EX-LEAD, Insulation Tester Lead Kit. Comes with 50 ft. test lead and included items above. GEO EARTH GROUND TESTERS •One-button measurement concept •3- and 4-pole earth ground measurement •4-pole soil resistivity testing •Selective testing, no disconnection of ground conductor (1 clamp) •Stakeless testing, quick ground loop testing (2 clamps) •Measuring frequency 128 Hz Includes: •Fluke 1623 tester •2 test leads •Batteries •Users manual Part No. 1623. FLUORESCENT LIGHT TESTER •Saves time and reduces costs •Perform all 5 essential lighting tests in under 30 seconds to pinpoint problems and verify operation when done •Survives on-the-job handling: drop-tested to survive from a six ft. (2 m) ladder •Easy to use: bright indicator light plus audible alert •Built to last, Easy to maintain: the Fluke 1000FLT’s extendable test rod is all metal and very rugged. But should the need arise, this test rod is easily replaced. Includes: •Quick reference guide •4 AA alkaline batteries •H1000 holster Part No. 1000FLT. SP01-42 GREGG DISTRIBUTORS LTD. 10kV INSULATION TESTER •Test voltages to up 10 kV •CAT III 1000 V, CAT IV 600 V safety rating •Warning function alerts the user that line voltage is present and gives the voltage reading up to 600 V AC or DC for increased user safety •Selectable test voltages in 50 V steps from 250 V to 1000 V, and 100 V steps above 1000 V •Measurements can be stored in up to 99 memory locations, with each location assigned a unique, user defined, label for easy recall •Long battery life gives the user over 750 tests between charges •Automatic calculation of Dielectric Absorption (DAR) and Polarization Index (PI) with no additional setup •Guard system eliminates the effect of surface leakage current on high-resistance measurements •Large digital/analog LCD for easy viewing •Capacitance and leakage current measurement •Ramp function for breakdown testing •Resistance measurements up to 2 TΩ •Timer settings up to 99 minutes for timed tests Includes: •Test cables with alligator clips (red, black, green) •Infrared adapter with interface cable •FlukeView® Forms Basic CD-ROM •AC power cord •Soft carrying case •English manual •User’s manual on CD-ROM •Quick reference card •Software license agreement •Registration card •FlukeView® Forms installation guide •USB-IR cable installation guide •Heavy duty alligator clip leads Part No. 1555. Part No. 1555/KIT, Kit includes IP67 hard carrying case, Ruggedized Alligator clips, Certificate of calibration, and above items. EARTH GROUND TESTER •3-pole Fall-of-Potential earth testing for basic measurements •2-pole resistance measurements for added versatility •Easily capture values with single-button operation •Ensure accurate measurements with automatic ‘noise’ voltage detection •Hazardous voltage warning offers increased user protection •Clearly read and record data with a large, backlit display •Rugged holster and design for tough work environments •Portable size allows for easy transportation •Instantly be alerted to measurements outside of your set limit, when you use the adjustable limit setting •600 V Cat II Includes: •Users manual •Two measuring leads with alligator clips, 2 m (6 ft) •One battery, 9 V alkaline •One protective holster, yellow •One CD-ROM Part No. 1621. Part No. 1621-KIT, Kit includes cables, ground stakes, and above items. GEO EARTH GROUND TESTER ADVANCED The Fluke #1625-2 is different from its sibling product the #1623-2 in a number of ways. The #1625-2 offers automatic frequency control (AFC) which helps identify existing interference and chooses a measurement frequency to minimize it’s effect. It is able to measure earth ground loop resistance using only clamps. With this test method, two clamps are placed around the earth ground rod and each are connected to the tester. No earth ground stakes are used at all. A known, fixed voltage is induced by the clamp and the current is measured using the second clamp. It automatically GEO EARTH GROUND TESTER determines the resistance of the earth ground rod. BASIC The Fluke 1623-2 earth ground tester is able to measure earth Part No. 1625-2. Part No. 1625-2-KIT, Kit includes: GEO Earth Ground Tester, ground loop resistances using only clamps. With this test User’s Manual, Batteries, Quick Reference Guide, USB Cable, method, two clamps are placed around the earth ground rod and each are connected to the tester. No earth ground stakes 2 Clamps, Professional Carrying Case, 4 Earth Ground Stakes, are used at all. A known, fixed voltage is induced by one clamp and 3 Cable Reels. and the current is measured using the second clamp. Then the tester automatically determines the resistance of the earth ground rod. This test method only works if a bonded earth ground system exists for the building or structure under test, but most are. If there is only one path to ground, like at many residential applications, the Stakeless method will not provide an acceptable value and the Fall-of-Potential test method must be used. With Stakeless testing, the earth ground rod does not need to be disconnected - leaving the bonded earth ground system intact during test. Gone are the days of spending time placing and connecting stakes for each earth ground rod on your system - a major time saver. You can also perform earth ground tests in places you’ve not considered before: inside buildings, power pylons, or anywhere you don’t have access T+CAN ELECTRICAL TESTER to soil. •Safer than traditional solenoid testers •3 forms of AC/DC Part No. 1623-2. voltage detection: lights, beeper, and vibration for added user Part No. 1623-2-KIT, Kit includes: GEO Earth Ground Tester, User’s Manual, Batteries, Quick Reference Guide, USB Cable, protection and convenience •Still indicates live voltage without 2 Clamps, Professional Carrying Case, 4 Earth Ground Stakes, battery power for added user protection •Extra-heavy-duty, replaceable test leads for added and 3 Cable Reels. durability •CAT IV 600 V, CAT III 1000 V rated for added user protection •Continuity beeper, GFCI Trip, Flashlight •Replaceable test probes for added convenience •Probe storage on back for added convenience •Probe holder for easier testing •Hazardous voltage warning light for added user protection •Test lead strap included for better test lead management •AC/DC Voltage: 12V / 600V •Autooff to save battery power Includes: •User manual •Test lead wrap •Fluke TP2 test probes •2 AAA Batteries Part No. T-PLUSCAN. FLUKE FLK/2266/2268 Testers INSULATION RESISTANCE TESTER •Test voltages to up 5 kV •CAT III 1000 V, CAT IV 600 V safety rating •Warning function alerts the user that line voltage is present and gives the voltage reading up to 600 V AC or DC for increased user safety •Selectable test voltages in 50 V steps from 250 V to 1000 V, and 100 V steps above 1000 V •Measurements can be stored in up to 99 memory locations, with each location assigned a unique, user defined, label for easy recall •Long battery life gives the user over 750 tests between charges •Automatic calculation of Dielectric Absorption (DAR) and Polarization Index (PI) with no additional setup •Guard system eliminates the effect of surface leakage current on high-resistance measurements •Large digital/ analog LCD for easy viewing •Capacitance and leakage current measurement •Ramp function for breakdown testing •Resistance measurements up to 2 TΩ •Timer settings up to 99 minutes for timed tests Includes: •Test cables with alligator clips (red, black, green) •Infrared adapter with interface cable •FlukeView® Forms Basic CD-ROM •AC power cord •Soft carrying case •English manual •User’s manual on CD-ROM •Quick reference card •Software license agreement •Registration card •FlukeView® Forms installation guide •USB-IR cable installation guide Part No. 1550C. Part No. 1550C/KIT, Kit includes IP67 hard carrying case, Ruggedized Alligator clips, Certificate of calibration, and above items. ADVANCED MOTOR & DRIVE TROUBLESHOOTING KIT VOLT LIGHT The products in this kit have been specifically selected for both troubleshooting and preventative maintenance applications. Establishing preventative maintenance programs are becoming critical to maintaining the uptime of electrical equipment and can significantly reduce both planned and unplanned downtime. Unplanned downtime costs are difficult to calculate, but often significant. For some industries, it can represent 1% - 3% of revenue (potentially 30% - 40% of profits) annually. Includes: •1587 Insulation Multimeter •i400 Current Clamp •9040 Phase Rotation Indicator •Remote probe •Test leads •Alligator clips •K-type thermocouple •Hard case •User documentation Part No. 1587-MDT. Non-contact AC voltage detector and LED flashlight with exclusive dual-sensitivity, combined in one convenient, compact design. The voltage detector glows blue when it’s near AC voltage, and glows red when it’s at the source. Detects voltages from 40 V AC to 300 V AC. Voltage detector glows blue 50 Hz - 60 Hz or 2.5 - 38 cm (1 - 5”) away from source. Operating temperature 0°C to 50°C. Ultra-bright white LED with 100,000 hour bulb life. AAA battery included. Part No. LVD1. II IR THERMOMETER, ELECTRICAL TESTER & VOLTAGE DETECTOR KIT This kit is designed to help electricians and HVAC technicians solve problems quicker. Test first for overheated electrical devices using an IR thermometer; then use electrical test tools to find out more about the problem. Includes: •T5-600 •62 MAX+ IR Thermometer •1ACII Voltage Detector •Soft carrying case Part No. T5-600/62-MAX+/1AC. PHASE ROTATION INDICATOR •3 phase indication •Indication of phase rotation •Clear LCD display •No battery required Includes: •3 self-retaining test probes (black) •Alligator clip •User manual Part No. 9040. Power Quality Tools & Power Analyzers POWER QUALITY CLAMP METER •AC/DC current: Clamp-on measurement of AC current up to 1400 A RMS and DC current up to 2000 A without breaking the circuit •Highest safety rating: 600 V CAT IV power analyzer is rated for use at the service entrance •Accurate in noisy environments: Clamp meter performs even with distorted waveforms present on electronic loads with low-pass filter •Data logging: Identify intermittent faults by logging any power quality parameter for minutes, or over a month, including harmonics •Verify batteries: Direct measurement of DC ripple (%) for battery and DC systems •Troubleshoot harmonics: Analyze and log harmonics digitally or graphically •Inrush current: Capture and analyze nuisance tripping, from 3 seconds to 300 seconds •Easy to use: Easily confirm power meter setup with large backlit color display of waveforms and trends •3-Phase power: Built in capability for balanced loads Includes: •345 Power Quality Clamp Meter •Soft carrying case •Power Log software •Test leads •Alligator clips •Test probes •USB cable •International AC adapter / battery eliminator •Printed English language user manual •Multilanguage manual CD Part No. 345. 705 LOOP CALIBRATOR For a powerful loop calibrator at a very affordable price, choose the new Fluke 705 Loop Calibrator. This feature-rich solution to loop calibration, maintenance and repair offers: •A large display and simple, pushbutton interface for ease of use •Simultaneous mA and % readout for quick, easy interpretation of readings •mA accuracy of 0.02% •Push button 25% steps for fast, easy linearity checks. Save time over traditional knob type controls. •”Span Check” for fast confirmation of zero and span •Selectable slow ramp, fast ramp, and step to provide smooth outputs for valve slewing and loop functional tests •24 volt internal loop supply, so you can power and read a transmitter at the same time without carrying a DMM •Single 9V battery that is easily changed •0 - 20 mA or 4 20 mA default start up modes Includes: •Alligator Clips •Protective yellow holster with Flex-Stand™ •Instruction sheet •TL75 safety-designed test lead set •NIST- traceable calibration report and data Part No. 705. 707 LOOP CALIBRATOR This feature-rich solution combines the best features pushbutton and knob-base loop calibrator and offers: •Large display and simple, quick-click interface for easy one-handed operation •Simultaneous mA and % readout for quick, easy interpretation of readings •mA accuracy of 0.015%, superior to other loop calibrators in this price range •1 µA resolution for mA source, simulate and measure •Push button 25% steps for fast, easy linearity checks •0-100% “span check” for fast confirmation of zero and span •Selectable slow ramp, fast ramp, and step ramp to provide smooth outputs for valve slewing and loop functional tests •24 volt internal loop supply, so you can power and read a transmitter at the same time without carrying a DMM •Measures V DC to 28 V •Single 9V battery that is easily changed without braking calibration seal •0 - 20 mA or 4 - 20 mA default start up modes •Innovative output adjustment dial with 1 µA and 100 resolution •HART ™ mode connects 250 Ω resistor in series with 24 V loop for compatibility with HART communicators Includes: •Alligator Clips •Protective yellow holster with Flex-Stand™ •Instruction sheet •TL75 safetydesigned test lead set •NISTtraceable calibration report and data Part No. 707. www.greggdistributors.ca SP01-43 FLUKE FLK/2266 Power Quality Tools & Power Analyzers PRECISION LOOP CALIBRATOR The Fluke 709 Precision Loop Calibrator is built around a user friendly interface with a Quick-Set rotary encoder knob. The protective holster easily fits into a technician’s hand and the large backlit display is easy to read, even in dark, cramped worked areas. The 709 offers: •Best-in-class accuracy at 0.01% reading •Small rugged design operates on (6) standard AAA batteries •Intuitive user interface with Quick-Set knob for fast setup, easy use •Built in selectable 250 Ω resistor for HART communication •24 V DC loop power with mA Measure Mode (-25% to 125%) •Resolution of 1 µA on mA ranges and 1 mV on voltages ranges •Simple two wire connection for all measurements •Auto Shutdown to conserve battery life (adjustable up to 30 minutes) •Variable step & ramp time in seconds •Adjustable span selection (0 to 20 mA or 4 to 20 mA) •Valve Test (simulate defined mA values with % keys) Includes: •Alligator Clip Set •420i Test Leads •Soft Case •Six AAA batteries (installed) •Product Manual CD-ROM •Quick Reference Guide •Safety Information Part No. 709. VOLT/mA CALIBRATOR •Measure loop current (0-20 mA, 4-20 mA) signals with very high accuracy of 0.015% and 1 mA resolution •Measure voltage output process signals from PLCs, transmitters •Source or simulate 24 mA loop current •Source voltage to 100 mV or 10V •24V loop supply with simultaneous current measurement •Enhanced voltage and current measure and source accuracy •Improved battery life •250 ohm HART resistor with loop power •Holster features test lead storage •Compatible with toolpack magnetic hanging system •Step and linear ramp output function •Configurable zero and span settings Includes: •Protective Yellow Holster with Test Lead Storage •Instructions Sheet (14 languages) •Single 9V alkaline battery •Test Leads and Alligator Clips •NIST- traceable calibration report and data Part No. 715. RTD PROCESS CALIBRATOR THERMOCOUPLE CALIBRATOR MILLIAMP PROCESS CLAMP METER ProcessMeter™ •Measure temperature from RTD output •Simulate RTD output •Operates with seven types of RTDs •Measure additional RTDs using Ohms measurement function •Simulate additional RTDs using Ohms source function •ºF or ºC selectable •Four shrouded banana jacks •Compatible with Rosemount® pulsed RTD transmitters (pulses > 10ms) •Holster features test lead storage •Compatible with toolpack magnetic hanging system Includes: •Protective Yellow Holster with test lead storage •Instructions Sheet (14 languages) •Single 9V alkaline battery •Test Leads and Alligator Clips •NIST-traceable calibration report and data Part No. 712 . •Best in class 0.2 % accuracy •0.01 mA resolution and sensitivity •Measure 4 to 20 mA signals without ”breaking the loop” •Measure mA signals for PLC and control system analog I/O •Dual backlit display with both mA measurement and percent of 4 to 20 mA span •Measurement Spotlight illuminates hard to see wires in dark enclosures •Detachable clamp with extension cable for measurements in tight locations •Measure 10 to 50 mA signals in older control systems using the 99.9 mA range •Automatically change the 4 to 20 mA output for remote testing •Power saving features, auto-off, backlight timeout extend battery life •Hold function captures and displays changing measurements •Measure 4 to 20 mA signals with in-circuit measurement •Simultaneous mA in-circuit measurement with 24V loop power for powering and testing transmitters •Source 4 to 20 mA signals for testing control system I/O or I/Ps •mA output linear ramp or 25% step output •Automatically change the 4 to 20 mA output for remote testing Includes: •Four AA alkaline batteries (installed) •Soft carrying case •Test leads •AC 72 detachable clip •Mini hook test leads •Instruction sheet •Hanging tool with hook and loop strap Part No. 772. Vibration Meters VIBRATION METER •Innovative sensor design helps minimize measurement variations caused by device angle or contact pressure •Consistent data quality at both low and high frequency ranges •Four-level scale indicates severity of problems for overall vibration and bearing condition •Exportable data via USB •Trending in Microsoft® Excel using built-in templates •Overall vibration measurement (10 Hz to 1,000 Hz) for acceleration, velocity and displacement units of measurement for a wide variety of machines •Crest Factor+ provides reliable bearing assessment using direct sensor tip measurements between 4,000 Hz and 20,000 Hz •Colored lighting system (green, red) and on-screen comments indicate how much pressure needs to be applied to take measurements •Temperature measurement with Infrared Temperature Sensor increases diagnostic capabilities •On-board memory holds up to 3,500 measurements •Audio output for listening to bearing tones directly •External accelerometer support for hard to reach locations •Flashlight for viewing measurement locations in dark areas •Large screen with high resolution for easy navigation and viewing Includes: •USB cable •Storage case •Belt holster •Quick reference guide •CD-ROM •Two (2) AA batteries Part No. 805. SP01-44 GREGG DISTRIBUTORS LTD. •Measure temperature from TC output •Simulate TC output •Operable with nine types of thermocouples •Calibrate linear TC transmitter with mV source function •Selectable ºF or ºC •Thermocouple mini-jack termination •Holster features test lead storage •Compatible with toolpack magnetic hanging system Includes: •Protective Yellow Holster with test lead storage •Instructions Sheet (14 languages) •Single 9V alkaline battery •NIST-traceable calibration report and data Part No. 714 . The Fluke 787 ProcessMeter™ puts a complete troubleshooting solution in the palm of your hand. Get in touch with more information, faster and easier with the newest member of the Fluke 80 Series, the 787 ProcessMeter. The 787 gives you the measurement capabilities you expect from our rugged, reliable DMMs plus the ability to source, simulate, or measure DC current with 1 microamp resolution and accuracy of 0.05%. Put it all together and you have the ideal tool for troubleshooting and calibrating current loop applications. So if you’re tired of always tracking down a calibrator, lugging around two tools and switching back and forth, get the single best solution for doubling your power. The 787 ProcessMeter from Fluke. Includes: •Alligator Clips •Protective Yellow Holster with Flex-Stand™ •One 9V alkaline battery •Quick Reference Guide •Safety-Designed Test lead Set Part No. 787. FLUKE FLK/2266/2267 Vibration Meters HANDHELD VIBRATION TESTER Take a vibration expert along Control unplanned downtime, prevent recurring problems, set repair priorities and manage your resources with an entirely new approach to vibration testing. The Fluke 810 helps you locate and diagnose common mechanical problems and prioritize repair actions with no prior machine history. Features: •On-board identification and location of the most common mechanical faults (bearings, misalignment, unbalance, looseness) focus maintenance efforts on root cause, reducing unplanned downtime •Fault severity scale with four severity levels helps you prioritize maintenance work •Repair recommendations advise technicians on corrective action •On-board context sensitive help provides real-time tips and guidance to new users •2 GB expandable on-board memory provides enough space for your machinery’s data •Self-test function ensures optimal performance and more time on the job •Laser tachometer for accurate machine running speed promotes confident diagnoses •Tri-axial accelerometer reduces measurement time by 2/3 over single axis accelerometers •Viewer PC Software expands data storage and tracking capacity Use the Fluke 810 Vibration Tester to: •Troubleshoot problem equipment and understand the root cause of failure •Survey equipment before and after planned maintenance and confirm the repair •Commission new equipment and ensure proper installation •Provide quantifiable proof of equipment condition and drive investment in repair or replacement •Prioritize and plan repair activities and operate more efficiently •Anticipate equipment failures before they happen and take control of spare parts inventories •Train new or less-experienced technicians and build confidence and skill across the team Includes: •Vibration Tester with diagnostic technology •Tri-axial accelerometer, magnet mount, mounting pad kit with adhesive, accelerometer quick-disconnect cable •Laser tachometer and storage pouch •Smart battery pack with cable and adapters •Shoulder strap and adjustable hand strap •Viewer PC software •Mini USB to USB cable •Getting Started Guide, illustrated quick reference guide, Users Manual CD-ROM •Carrying case Part No. 810. Part No. 810S, Replacement vibration sensor. Thermometers 60 SERIES HANDHELD INFRARED THERMOMETERS These handheld portable tools enable professionals to monitor the status of electrical motors and electrical panels, research heating and ventilation problems and diagnose car malfunctions with ease. INFRARED & CONTACT THERMOMETER •IR thermometer for quick measurements up close, or at a distance, without a ladder •Contact thermometry capability, compatible with all standard mini-connector type K thermocouples, preserves your investment in thermocouples •Fabric hook-and-loop fastener pipe probe for superheat and Part No. 61, Features: •Bright laser beam provides easy target- sub-cooling and other contact and ambient measurements ing •Display clearly supplies data at a glance •Shock-absorb- •Single-point laser sighting •Temperature range of -40 °C ing holster increases ruggedness •0.2 °C (0. 5 °F) resolution to 550 ° C (-40 °F to 1022 °F) covers most industrial and up to 275 °C (525 °F) •Backlight illuminates the screen in the residential applications •Easy emissivity adjustment (Lo, Med, dark •Automatic sleep mode after 7 seconds extends battery Hi) for measuring pipes and other shiny materials more aclife •Alkaline batteries provide 4000 typical measurements curately •Lightweight (just 12 ounces/340 grams) and portable •Very easy to use •Efficient – no need to shut down equipment Part No. 63, Features: •High-resolution optics •High accuracy: when making IR measurements •MIN, MAX, and DIF functions 1 % and repeatability: 0.5 % •MAX temperature display •Laser help you quickly identify problems •Scan large areas or small targeting •Backlit display •Expanded measurement range up objects quickly and efficiently to 535 °C (999 °F) Includes: •561 IR thermometer •K-Type thermocouple •Fabric hook-and-loop fastener pipe probe •Hard carrying case •2 AA batteries •Users manual Part No. 561. 61 INFRARED & CONTACT THERMOMETERS •Easily access advanced features with the soft-key buttons and dot-matrix display •Compatibility with all standard miniconnector Type-K thermocouples allow you to preserve your thermocouple investments •Confidently measure a wide variety of surfaces, with the adjustable emissivity feature, including a built-in material table •Capture multiple points of data (up to 99 with the 568, and 20 with the 566), for downloading and recalling later •Easily adapt to lighting conditions with 2 levels of backlight •Audible and visual alarms instantly alert you to measurements outside of your set limits •Quickly identify problems with the MIN, MAX, AVG, and DIF functions •Make contact thermometer measurements right away with the included TypeK thermocouple bead probe •Confidently troubleshoot equipment with 1 % measurement accuracy •Versatile interface with 6 languages from which to choose Includes: •Thermocouple K bead probe •Durable hard case •2 AA batteries •Getting Started guide in 6 languages •User’s Manual on CD in 6 languages •2-year warranty Part No. 566, Temperature range: -40 °C to 650 °C (-40 °F to 1202 °F); Distance to Measurement Spot Size: 30:1. Part No. 568, Temperature range: -40 °C to 800 °C (-40 °F to 1472 °F); Distance to Measurement Spot Size: 50:1. 63 DIGITAL THERMOMETERS •Relative time clock on MIN, MAX, and AVG provides a time reference for major events •Electronic Offset function allows compensation of thermocouple errors to maximize overall accuracy •J, K, T, E, N, R, and S type thermocouple (temperature sensors). •Readout in °C, °F, or Kelvin (K) •Splash and dust resistant case protected by impact absorbing holster •User-friendly front panel is easy to set up and operate •Sleep mode increases battery life; typical 1000-hour battery life •Battery door allows easy battery replacement without breaking the calibration seal Part No. 51-2, Single Input. Part No. 52-2, Double Input. www.greggdistributors.ca SP01-45 FLUKE FLK/2267 Thermometers DATA LOGGING DIGITAL THERMOMETERS INTRINSICALLY SAFE IR THERMOMETER HIGH-TEMPERATURE INFRARED THERMOMETER FoodPro FOOD SAFETY THERMOMETER FoodPro PLUS FOOD SAFETY THERMOMETER VISUAL IR THERMOMETER •Relative time clock on MIN, MAX, and AVG provides a time reference for major events •Electronic Offset function allows compensation of thermocouple errors to maximize overall accuracy •Measures J, K, T, and E-types of thermocouples •Readout in °C, °F, or Kelvin (K) •Splash and dust resistant case protected by impact absorbing holster •User-friendly front panel is easy to set up and operate •Sleep mode increases battery life; typical 1000-hour battery life •Battery door allows easy battery replacement without breaking the calibration seal •Additional thermocouple types R, S, and N (for a total of 7 different types) •Recall function allows logged data to be easily reviewed on the meter display •USB communication port allows data to be exported to optional FlukeView Forms® Temperature PC software for further analysis and graphing •Data Logging up to 500 points of data with user adjustable recording interval Part No. 53-2-B, Single Input. Part No. 54-2-B, Double Input. The easy-to-use and highly accurate Fluke FoodPro noncontact thermometer instantly measures surface temperature, allowing users to make rapid and frequent non-contact temperature measurements without risk of cross contamination. •Infrared temperature range from -35 to 275 ºC •HACCP check lights for instant recognition of safe/unsafe temperatures •LED target illumination highlights the entire measurement spot for accurate targeting •Hand washable (IP54 sealed) Includes: •AA battery •Quick Start guide Part No. FP. VISUAL IR THERMOMETER ELECTRICAL COMBO KIT Get extra value along with the complete solution with the VT04 Visual IR Thermometer Electrical Combo Kit. Troubleshoot and solve problems more efficiently. Get a VT04, Fluke 376 Clamp Meter and Fluke 117 Digital Multimeter today and save. Includes: •VT04 Visual IR Thermometer •376 AC/DC TrueRMS Clamp Meter •117 Electricians’ Multimeter Part No. VT04-ELEC-KIT. SP01-46 GREGG DISTRIBUTORS LTD. •Meets intrinsically safe certifications in Class I Div 1 and Div 2 or Zone 1 and 2 hazardous environments from recognized safety agencies around the world •Measure -40 °C to 800 °C /-40 °F to 1472 °F •Conductive Case for carrying the IR thermometer safely into hazardous area •Easily access advanced features with the soft-key buttons and graphical display •Measure small objects from further away, with a distance-to-spot ratio of 50:1 •Compatible with mini-connector K-type thermocouple (KTC) probe •Confidently measure a wide variety of surfaces with the adjustable emissivity feature, including a built-in material table •Capture up to 99 points of data •Troubleshoot equipment with ± 1 % measurement accuracy •Versatile interface with five languages from which to choose Part No. 568EX/ETL. The Fluke FoodPro Plus combines an infrared non-contact thermometer for surface scans with a probe thermometer for internal temperature readings. An integrated countdown timer with alarm monitors line checks as well as cooking and cooling intervals. Includes all of the FoodPro features, plus the following: •Built-in fold-out probe for measuring internal food temperatures •Probe temperature range -40 to 200 ºC •Countdown timer to monitor cooking, cooling and HACCP exposure times •Backlit display for clear readings in poorly lit areas •MAX temperature displayed for quick reference Includes: •Built-in contact probe •9 V alkaline battery •Quick start guide •Operator’s guide •Soft carry pouch Part No. FP-PLUS. Part No. FP-PROBE, Replacement probe. VISUAL IR THERMOMETER HVAC COMBO KIT Save money and equip yourself with the VT04, Fluke 902 Clamp Meter and Fluke 116 Digital Multimeter. Together, these tools equip HVAC technicians to troubleshoot and diagnose the most stubborn issues Includes: •VT04 Visual IR Thermometer •902 True-RMS HVAC Clamp Meter •116 Digital Multimeter Designed Specifically for HVAC Professionals Part No. VT04-HVAC-KIT. •Measure -30°C to 900°C (-22°F to 1652°F) •60:1 distance to spot ratio with dual laser sighting for fast, accurate targeting •Multi-language interface (user select) •Current Temperature plus MAX, MIN, DIF, AVG temperature displays •Compatible with standard mini-connector K-type thermocouples, including ones you already own and have installed •Adjustable emissivity and predefined emissivity table •Infrared and thermocouple temperature on backlit display •Last reading Hold (20 seconds) •High and low temperature alarm •Data storage and review (99 data sets) •Tripod mount •12 or 24 hour clock •USB 2.0 computer interface cable •FlukeView® Forms documenting software Includes: •K-type thermocouple bead probe •Durable hard case •USB 2.0 computer interface cable Part No. 572-2. •Visual image and infrared heat map blending - Identify the exact location of the potential issue by blending the visual image with the heat map overlay at 0%, 25%, 50%, 75%, and 100% infrared with one button •NEAR and FAR mode - Align the visual and thermal lenses to correctly identify the location of the issue •Center measurement box - See the exact area of temperature measurement right on the screen •Temperature alarms and automated monitoring features - Identify intermittent problems by monitoring equipment over time or get alerts when a temperature is outside the expected range •Hot and cold markers - Instantly identify hottest and coldest spots within the field of view •Save in .bmp or .is2 format - Choose .bmp when all you want is the image, or use .is2 format that can be edited in SmartView® software •SmartView® reporting software - Optimize the image blending and palette and quickly create professional reports •Pocket-size design - Handy when you need it; easily fits in your tool bag or pocket •Intuitive interface - Get to work as soon as you take it out of the box Includes: •VT04A Visual IR Thermometer •Soft case •Micro-SD card •Micro-SD conversion adapter to standard •AA batteries (4) •Printed quick reference guides Part No. VT04A. VISUAL IR THERMOMETER HVAC COMBO KIT The VT04 and Fluke 1507 Insulation Resistance Tester are ideal companions for troubleshooting and preventive maintenance applications Includes: •VT04 Visual IR Thermometer •1507 Insulation Resistance Tester Part No. VT04-MAINT-KIT. FLUKE FLK/2267 Thermometers IR THERMOMETER, CLAMP METER & VOLTAGE DETECTOR KIT This kit is designed to help electricians and HVAC technicians solve problems quicker. Test first for overheated electrical devices using an IR thermometer; then use the clamp meter and voltage detector to find out more about the problem Includes: •Fluke 62 MAX+ IR Thermometer •Fluke 323 True-RMS Clamp Meter •Fluke 1AC II VoltAlert Voltage Detector •C115 Soft Case Part No. 62-MAXPLUS-323/1AC. LASER DISTANCE METER/INFRARED THERMOMETER COMBO KIT The most rugged Fluke 62 MAX+ IR thermometer teamed with the easy to use 414D Laser Distance Meter has everything you need to configure layout and to troubleshoot electrical/HVAC problems quickly. •Use the IR thermometer to test for overheating in electrical devices and HVAC components •Use the laser distance meter to determine distance, area, and volume for space configuration. Includes: •414D Laser Distance Meter •62 MAX+ IR Thermometer Part No. 414D/62-MAXPLUS. Laser Distance Meters IP54 LASER DISTANCE METER •Measures up to 100 m (330 ft) •Higher accuracy: +/-1 mm (0.04 in) •4-line display shows you even more data at a glance •Inclination sensor assists with height tracking, leveling, and indirect horizontal distance measurements when line-of-sight is blocked by an obstacle •Corner angle feature, allows you to determine the angle of a corner •Compass provides a “heading” for your distance measurements •Stores 20 complete displays for quick recall •Backlight •Tripod mode allows you to mount the meter to a tripod when measuring long distances •Full Pythagoras function for height measurements •Audible keypad feedback •Stake Out feature helps you mark out defined lengths such as when constructing wooden frames •Automated End-piece Correction for measuring from an edge or corner •A built-in sensor detects the position of this bracket and automatically changes the reference point •Minimum/Maximum function •Enhanced environmental protection: IP54-rated as dust and water spray resistant •Improved battery life of 5000 measurements with auto shut-off feature Part No. 424D. Thermal Imagers Ti100 THERMAL IMAGER Fluke Ti100 general purpose thermal imager includes a 160x120 9Hz infrared detector with 0.10°C thermal sensitivity •Focus-free infrared: The Ti100 offers the highest performing one-handed, focus-free infrared system available. From four feet (1.2 M) and beyond you’ll always be in good focus no matter what you’re inspecting. •Laser pointer: A laser pointer allows you to accurately point to an area of concern to a colleague or customer. •Built rugged: The new Fluke imagers are the most rugged and reliable, lightweight professional point-and-shoot thermal imagers on the market. They’ve been put through a battery of tests, including two-meter drops, vibration, extreme temperature and humidity, and electromagnetic/radio frequency interference testing to ensure they survive in your environment. •One-hand operation: The Ti100 has been designed for simple, one-handed operation. Its lightweight, slim profile makes it easy to operate in either landscape or portrait format - your choice. All so you’ll have one hand free to steady yourself or hold another tool. Part No. TI100/9HZ. Ti110 THERMAL IMAGER Fluke Ti110 thermal imager industrial/commercial applications features a 160x120 30Hz infrared sensor with 0.10°C thermal sensitivity and the industry’s first IR Fusion image blending in a point-and-shoot camera •Exclusive IR-OptiFlex focus system - ensures that images are in good focus from 1.2 meters (4 ft.) and beyond for optimum image clarity and scanning convenience. For shorter distances change to manual mode with the touch of a finger •Compatible with Fluke Connect •IR-PhotoNotes annotation system - Quickly identify and keep track of inspection locations by adding digital images of important information surrounding areas •Detect issues faster with precisely blended visual and infrared images with patented IR-Fusion technology with AutoBlend mode •Multi-mode video recording - focus-free video in visible light and infrared with full IR-Fusion •Easily communicate the location of problems with the Electronic 8-Point Cardinal Compass Includes: AC power adapter, lithium ion smart battery, USB cable, SD memory card, hard carrying case, soft transport bag, adjustable hand strap (left- or right-handed use), printed users manual, SmartView® software and warranty registration card. Part No. TI110/30HZ. www.greggdistributors.ca SP01-47 FLUKE FLK/2264/2265 Thermal Imagers Ti200 & Ti300 THERMAL IMAGER •Equipped with new LaserSharp™ Auto Focus •Features wireless connectivity compatible with Fluke Connect. •Detect and communicate issues faster with patented Fluke IR-Fusion® technology with AutoBlend™ mode •Faster communication with wireless image transfer directly to your PC, Apple® iPhone® or iPad® •One-handed, easy-to-use user interface •Ruggedized high resolution 640x480 capacitive touch screen for quick menu navigation •Capture additional digital images to show location or additional site details with IR-PhotoNotes™ Annotation System •Standard and radiometric video recording* •Streaming video (USB and HDMI) •Text* and voice recording and annotation gets additional details saved with the image file •High-temperature measurement •Included SmartView® and SmartView Mobile App Analysis and Reporting Software Includes: •Thermal imager with standard infrared lens •AC power supply and battery pack charger (including mains adapters) •Two, rugged lithium ion smart battery packs •Micro SD memory card with SD adapter •3m USB cable •3m HDMI video cable •SmartView® software with free software upgrades for life •Rugged, hard carrying case •Soft transport bag •Adjustable hand strap •Printed user’s manual •CD user’s manual •Warranty registration card Part No. TI200/60HZ, 60Hz 200X150. Part No. TI300/60HZ, 60Hz 200X180. Ti9 THERMAL IMAGER Fluke Ti9 9Hz entry-level thermal imager for general purpose applications. Features a 160x120 infrared detector with 0.20°C thermal sensitivity and a temperature measurement range of -20°C to 250°C (-4°F to 482°F). •Superior resolution to view more essential details •Small details are visible in a perfectly focused image •Large widescreen full VGA color LCD display •Temperature range supports basic electrical and mechanical applications •Intuitive, three-button menu, simply navigate with the push of a thumb •Adjustable focus •Just point, shoot and the image is captured. It is that easy. •Withstands dust and water, IP54 rating •Withstands a drop test of 2 meters •Protective lens cover Part No. TI9-9HZ. THERMAL IMAGING SCANNER Fluke TiS thermal imaging scanner for rapid visual temperature analysis. Features a 120x120 infrared detector with 0.1° 9Hz thermal sensitivity The Fluke TiS Thermal Imaging Scanner, for building diagnostics, is the most affordable thermal imaging camera that meets the proposed RESNET infrared inspection standard. Now Fluke quality, durability, and performance are available in a thermal imager engineered for the value-conscious building professional. The Fluke TiS is an entry level thermal imager for quick, easy, and accurate problem identification and troubleshooting designed specifically for the building inspection professional. Includes: •TiS Thermal Imaging Scanner with standard infrared lens •AC power supply/battery charger (including mains adapters) •SD memory card •Multi-format USB memory card reader for downloading images •SmartView® software with free software upgrades for life •Rugged, hard carrying case •Soft transport bag •Adjustable hand strap •Users manual on CD •Warranty registration card •Interactive training DVD Part No. TIS-9HZ. Test Tools - Fluke Connect Wireless System FC WIRELESS AC/DC CURRENT MODULE FC WIRELESS DC VOLTAGE MODULE FC CONNECTOR This fully functional DC voltage meter that wirelessly relays DC voltage measurements to other Fluke Connect enabled master units. The Fluke v3001 FC is capable of measuring up to 1000V DC while logging up to 65,000 readings. The V3001 FC includes a set of TL222 Test Leads, AC220 Alligator Clips and a magnetic hanging strap. Part No. V3001FC. Fluke Connect ir3000 FC Connector allows you to wirelessly transfer data from your existing Fluke Connect Tools to your smart phone. •Fits over the IR port of your existing Fluke Connect Tools •Upgradable by USB •Immediately enables you to graph, save and share the tool’s reading with your team from your smart phone Part No. IR3000FC. A3000 FC KIT A3001 FC KIT T3000 FC KIT The Fluke A3002 FC current module wirelessly relays measurements from a current clamp accessory to Fluke Connect enabled master units. The A3002 FC was designed to be used with the i410 or i1010 AC/DC current clamps (not included). Capable of measuring up to 400A AC/DC when used with the i410 current clamp, and either 600A AC or 1000A DC when combined with the i1010 current clamp. Internal logging feature allows for up to 65,000 readings to be stored. The A3002 FC can be utilized as a standalone unit or combined with other Fluke Connect modules, allowing you to completely customize your wireless test tool suite. Part No. A3002FC. Fluke Connect Enabled Kit for measuring and testing AC Current. Includes the A3000 FC Clamp Meter and 3000 FC Multimeter. Part No. A3000FC-KIT. SP01-48 GREGG DISTRIBUTORS LTD. Fluke Connect Enabled Kit with iFlex clamp module for measuring and testing AC Current. Includes the A3001 iFlex Module and 3000 FC Multimeter Part No. A3001FC-KIT. Fluke Connect Enabled Kit with wireless K-Type temperature module. Includes the T3000 K-Type temperature module and 3000 FC Multimeter. Part No. T3000FC-KIT. FLUKE FLK/2263/2264 Test Tools - Fluke Connect Wireless System V3000 FC KIT V3001 FC KIT V3003 FC KIT AIRBORNE PARTICLE COUNTER CARBON MONOXIDE METER ASPIRATOR KIT Fluke Connect Enabled Kit with wireless AC Voltage module. Includes the V3000 module and 3000 FC Multimeter. Part No. V3000FC-KIT. Fluke Connect Enabled Kit with wireless DC Voltage module. Includes the V3001 module and 3000 FC Multimeter. Part No. V3001FC-KIT. Fluke Connect Enabled Kit with wireless DC and AC Voltage modules. Includes V3000 and V3001 Voltage modules, as well as the 3000 FC Multimeter. Part No. V3003FC-KIT. Indoor Air Quality Tools The new Fluke 985 Particle Counter is the preferred choice for HVAC and IAQ professionals. From filter testing to IAQ investigations, the Fluke 985 is the portable solution for determining airborne particle concentrations •Six channels and particle size range of 0.3 - 10.0 µm: Assures accurate measurements even for critical locations requiring ISO Class 5 - 9 certification •Ultra-lightweight and ergonomic design: Promises easy single-hand operation in tight or awkward spaces with less operator fatigue •Long battery life: Ten hours of standard-use battery life to last a full work day •Large 3.5 QVGC Color display: Easy navigation and viewing with the intuitive icons and large font options •10,000 record storage: Quick access to historical data •On-screen data presentation: Data can be viewed in a traditional tabular or trend graph view at the user’s preference •Personalized setting and configurations: Customizable settings for the display, sample methods, and alarm settings for sample count •Data export options: Download data to a PC using a USB memory stick, USB cable or Ethernet connection. No special software is required to download or view data •Option password control: Confirms security when required •USB/Ethernet charge cradle: Assures device is always ready to go when needed Part No. 985. •Rugged case and electronics •Large LCD displays CO levels from 0 to 1000 ppm •Bright back-light allows easy screen viewing under dim lighting conditions •Beeper triggers with increasing frequency as CO levels rise •MAX Hold function stores and displays the maximum CO level •Automatic sensor zeroing and self-test sequence upon start-up •CO level beeper can be silenced if desired •Automatic power-off after 20 minutes extends battery life •Easy to replace battery •Replaceable sensor extends tool life •C50 soft carrying case, battery and instruction sheet •Stabilized electrochemical CO specific sensor •Typical three year sensor life; one year calibration cycle •Battery life typical 500 hours with alkaline battery Part No. CO-220. •Sample flue gas with your Fluke #CO-220 using the #CO-205 Aspirator Kit •Draw flue gas samples up to 370°C (700°F) reliably for measurement with the Fluke #CO-210 Carbon Monoxide probe or Fluke #CO-220 Carbon Monoxide meter •The #CO-205 aspirator accessory kit contains all the components necessary to provide a clean sample for the Fluke family of gas measuring devices Part No. CO-205. HVAC/R REFRIGERANT LEAK DETECTOR FLASHLIGHT The compact, easy-to-use, Fluke #RLD2 UV flashlight uncovers refrigerant leaks instantly. Use the UV light to find the leakage area, then, use the laser pointer to pinpoint the exact leak location. With 100,000 hours of life, and four operating modes, this versatile leak detector is a must have for HVAC Technicians. Features and benefits of the #RLD2: •Six UV LEDs (395 nm wavelength) detect leak detection dyes •Laser pointer clearly locates center of the UV field for accuracy •Three LED flashlight with 100,000 hour LED life •Operating temperature 0°C to 50°C •Four operating modes: flashlight, UV light, laser light, UV/laser light combination •Convenient detachable key chain carabiner and AAA battery included Part No. RLD2. www.greggdistributors.ca SP01-49 FLUKE FLK/2262 Accessories INTEGRATED DMM TEMPERATURE PROBE TYPE K MALE MINICONNECTORS TYPE-K VELCRO THERMOCOUPLE TEMPERATURE PROBE TYPE K PIPE CLAMP KIT SureGrip™ AIR TEMPERATURE PROBE SureGrip™ PIERCING TEMPERATURE PROBE SureGrip™ TAPERED TEMPERATURE PROBE SURFACE PROBE •Type-K thermocouple with tapered tip for use in air, non-caustic gas and surface applications •Measurement range:-40 to 816°C Part No. 80PK-26. •Designed for measuring the temperature of flat or slightly convex surfaces, this K type probe is ideal for hot rollers and plates. •Measurement range: 0 to 260°C Part No. 80PK-3A. SureGrip™ PIERCING TEMPERATURE PROBE EXTENSION WIRE KIT THERMOCOUPLE MODULE 3 PC. ALLIGATOR CLIP SET •Operates with T-type thermometers •Measurement range : -196 to 350°C Part No. 80PT-25. •Extending and repairing T-type thermocouple wires •Kit includes 3 meters of thermocouple wire and 1 pair of male/female mini-connectors •Maximum continuous exposure temperature: 260°C •Designed for T-type thermometers Part No. 80PT-EXT. ALLIGATOR CLIPS & ADAPTERS HEAVY DUTY INSULATION PIERCING TEST CLIP LED PROBE LIGHT MINI HAT LIGHT Type-K thermocouple with standard banana jack •Convenient one piece construction •Compatible with DMMs with temperature measurement functions •Measurement range:-40 to 260°C Part No. 80BK-A. •Designed with SureGrip, a superior gripping surface made from thermoplastic rubber. •Type-K thermocouple for use in air and noncaustic gas measurements •Bead protected by perforated baffle •Measurement range:-40 to 816°C Part No. 80PK-24. Includes #AC285, a pair of red and black extra large alligator clips plus adaptors to securely attach the #AC285 alligator clips to Fluke fused test probes #FTP-1 and #FTPL-1. Part No. AC285-FTP. •Isothermal screw terminal for K wire •Suitable for up to 20 gauge thermocouple wire •Color-coded to industry standards (K-yellow) •Two male mini-connectors per package •Pack of 2 Part No. 80CK-M. •K-type probe designed for use in soft or semi-hard materials, and can be used in liquid or gel. Ideal for food service applications •Designed with SureGrip, a superior gripping surface made from thermoplastic rubber. •Measurement range : -40 to 350°C Part No. 80PK-25. Plunger style insulation piercing clip with insulation jaws. The stainless steel tip pierces insulated wires for otherwise inaccessible test points. Recommended for use with TL224 test leads. Compatible with all test leads with standard 4 mm, shrouded banana plug. Pierces insulated wires from 30 AWG (0.25 mm square) to 14 AWG (1.5 mm square). Small pin allows self-healing of the insulation. CAT IV 600V, CAT III 1000 V, 5 A rating. UL listed Part No. AC89. SP01-50 GREGG DISTRIBUTORS LTD. Kit Includes: •80PK-8 for pipe diameters of 6 mm to 32 mm •80PK-10 for pipe diameters of 32 mm to 64 mm •Soft carrying case Designed to be compatible with any temperature measuring instrument that accepts Type-K Part No. 80PK-18. thermocouples, has a miniature thermocouple connector, and has cold reference junction compensation. Designed for hands free measurement of HVAC temperature measuring applications. Use multiple probes and leave in place for route based routine maintenance. Part No. 80PK-11. •Converts a DMM to a thermometer •For use with type-K thermocouples in low voltage applications (below 24 V AC, 60 V DC) •Measurement range: -50 to 1000°C (probe dependent) Part No. 80TK. •Small, rugged light easily attaches to any Fluke test probe •Bright white LED illuminates contact area •Frees both hands for work •120 hours of battery life •Uses 2 3-volt watch batteries Part No. L200. Set of three (one red, one gray, one black) safety designed insulated Probe Tip Alligator Clips. Designed for use with STL 120 Shielded Test Leads and TL75 Test Leads. Accepts standard 0.08’’ (2 mm)-pin tip sized test probes. Nickel-plated steel jaw contact material with standard jaw opening of 5/16’’ (8 mm). •Maximum Voltage: 600Vrms CAT III per IEC 1010-2-031 •Maximum Current: 10A Part No. AC120. •Rugged, high intensity Xenon worklight allows you to work with both hands •Attaches to a baseball hat -- includes hat clip •Electrically and thermally non-conductive •Withstands 6 ft. drops to concrete •Waterproof •Rugged ABS case won’t crack or chip •Bright xenon lamp in a pre-focused optical quality reflector Part No. L205. FLUKE FLK/2262 Accessories DELUXE LED HAT LIGHT • Attach it to a hard hat, a baseball hat, or even a panel door for all the light you need •3 super bright white LEDs •360° Rotating clip •Special hard-hat attachment included •40-hour battery life •Water resistant •Durable polymer construction •Rubber shielded Bezel •Also includes a neck lanyard Part No. L206. PROBE LIGHT KIT Special value combo pairs the new L200 Probe Light with one of the most popular test leads by Fluke and a handy carrying case. •Small, rugged light easily attaches to any Fluke test probe •Flexible silicone test leads are heat and cold resistant •Zippered case has two inside pockets •Probe light frees both hands for work •120 hours of battery life •Uses (2) 3V watch batteries Part No. L211. SureGrip™ KIT with PROBE LIGHT AND PROBE EXTENDER Includes: •Probe Light •20 cm Test Probe Extenders •SureGrip Test Probes •SureGrip Silicon Test Lead Set •Foldable soft pouch with six pockets and hook-and-loop Part No. L215. 3 PK. TEST LEAD WRAP •Durable nylon hook and loop fastener •8” length •Sold in packs of 3 Part No. LEADWRAP. Hard hat not included. INDUCTIVE PICK-UP/ EXTERNAL TRIGGER •Provides RPM readings Part No. RPM80. FUSES Part No. 871173, 5 pk. 630 mA 250V. Part No. 871202, 5 pk. 3A 600V. Part No. 892583, 15A 600V. SLIP-N-GRIP® SNG/3177 Car Accessories DISPENSER RACKS Part No. FB-P9833-89, Floor Dispenser Rack. Part No. FB-P9933-31, Expandable Wall Rack. Part No. FB-P9943-54, Wall Dispenser Rack. Part No. FB-P9943-82, Adhesive Floor Mat Rack. CHP/1633 FLOOR RACK START-UP KIT This sturdy rack comes with everything you need to start keeping vehicles clean with genuine Slip-N-Grip® vehicle service products. Each kit contains: •Sturdy Slip-N-Grip® dispensing rack with casters •250 Seat Covers •250 Paper Floor Mats •500 Plastic Floor Mats •500 Parts Bags •250 Steering Wheel Covers •100 Tire/Trash Bags Part No. FK-P9943-76. WALL RACK START-UP KIT Sturdy Slip-N-Grip® dispensing rack includes: •Shelf •500 Plastic Floor Mats •500 Parts Bags •250 Seat Covers •250 Steering Wheel Covers Part No. FK-P9943-94. CHAPIN® Industrial Sprayers INDUSTRIAL CLEANER/DEGREASER SPRAYER •Wide mouth for no-mess filling and cleaning •Curved poly extension wand with adjustable poly cone nozzle •Durable poly tank with automatic pressure relief valve Part No. 22350XP, 2 gallon. Part No. 22360XP, 3 gallon. www.greggdistributors.ca SP01-51 21 L OCA TIO NS: ALBERTA EDMONTON - MAIN 16215-118 Avenue, T5V 1C7 Ph: 780-4-GREGGS (447-3447) Fax: 780-451-2528 GRANDE PRAIRIE 11140 - 97 Avenue, T8V 3J8 Ph: 780-513-4000 Fax: 780-513-6000 HIGH LEVEL EDMONTON - EAST 10207 - 96 Street, T0H 1Z0 3611 - 76 Avenue, T6B 2S8 Ph: 780-926-2521 Fax: 780-926-3514 Ph: 780-450-2233 Fax: 780-450-2266 RAINBOW LAKE EDMONTON - SOUTH 2 Rainbow Drive, Box 823, T0H 2Y0 3911 - 92 Street, T6E 6R8 Ph: 780-956-2588 Fax: 780-956-2589 Ph: 780-409-2000 Fax: 780-409-2100 RED DEER NISKU 5141 - 76A Street Close, T4P 3M2 1405 - 5 Street, T9E 8C7 Ph: 403-341-3100 Fax: 403-341-3210 Ph: 780-979-9988 Fax: 780-979-9989 SPIRIT RIVER ATHABASCA 5202 Highway 49, Box 579, T0H 3G0 5006 - 52 Street, T9S 1V3 Ph: 780-864-3333 Fax: 780-864-3330 Ph: 780-675-3110 Fax: 780-675-4774 STRATHMORE CALGARY - MAIN 1020 Westridge Road, T1P 1H8 5755 - 11 Street S.E., T2H 1M7 Ph: 403-934-3710 Fax: 403-934-5453 Ph: 403-253-6463 Fax: 403-253-5926 BRITISH COLUMBIA CALGARY - FOOTHILLS 6130 - 51 Street S.E., T2C 4M9 FORT ST. JOHN Ph: 403-203-1928 Fax: 403-236-1912 9404 - 111 Street, V1J 7J5 Ph: 250-785-8000 Fax: 250-785-8022 CLAIRMONT 9802 - 84 Avenue, T0H 0W0 LANGLEY Ph: 780-567-2238 Fax: 780-567-2239 19632 - 96 Avenue, V1M 3B9 Ph: 604-888-9588 Fax: 604-888-4688 DRAYTON VALLEY 6105 - 50 Avenue, Box 5055, T7A 1R3 NANAIMO Ph: 780-621-0056 Fax: 780-621-0057 1935 Boxwood Road, V9S 5X9 Ph: 250-754-1935 Fax: 250-754-1165 FAIRVIEW 9402 - 113 Street, Box 2020, T0H 1L0 SASKATCHEWAN Ph: 780-835-5115 Fax: 780-835-3535 SASKATOON FORT McMURRAY 3066 Faithfull Avenue, S7K 8H2 325 MacAlpine Crescent, T9H 4Y4 Ph: (306) 343-6655 Fax: (306) 343-6656 Ph: 780-715-4000 Fax: 780-743-8833 www.greggdistributors.ca Items may not be exactly as illustrated. Quantities on some items may be limited. Errors are subject to correction. ©2015 Gregg Distributors Ltd. All rights reserved.
© Copyright 2024