Download Report

Dated:01/Feb/2015
HANSU CONTROLS
: PLOT-W-281(A) T.T.C. INDS AREA, MIDC, RABALE NAVI MUMBAI - 400701 MAHARASHTRA INDIA.
PHONE No. : (022) 65193145, 27690037
MOBILE No. : 9821550302,9821185228
FAX No. : 27690038
ADDRESS
E-MAIL
: [email protected], [email protected]
CST TIN No. : 27270691652 DT:22.01.09
PAN No.
: AFZPS4414A
BANK
: HDFC BANK LTD
WEBSITE
VAT TIN No.
SSI REG.
ACCOUNT No.
: 04062320000957
RTGS/NEFT/IFSC
: www.hansucontrols.com
:
: 27-021-11-06637 DT:18.12.14
Branch:
: HDFC0000406
Ghatkopar (W)
Complete Details of HP01
Group HP) SPECIFICATION & PRODUCTS FOR INDUSTRIAL WP BREAK GLASS TYPE P.B.STATION/CONTROL
STATION/LCS/LPBS (PIL BOX/MANUAL CALL POINT/BREAK GLASS) IN CAST ALUMINIUM (LM-6) ENCLOSURES :- Supply of Cast
Aluminium Pil box suitable for wall/Structure mounting. All the enclosures are cast out of superior quality aluminium alloy. All the surfaces are
carefully cleaned and levelled so as to give very smooth surface. All the enclosures are chromatised and finally epoxy powder coated by static
charge spray method by RED colour per IS5. Powder coating gives very tough durable and extremely smooth coating on the surface.All the
mating surfaces are provided with round rubber gasket in the groove so as to make it effectively dust and vermain proof.
MOUNTING :- External lugs are provided for fixing. The lugs offset such that the rear part of the unit stays away from surface.
FIXING OF ELEMENTS :- For wall mounting L & T make 1NO+1NC contact element is mounted inside.Cover is fixed bolted type.A pointed
piece is fixed on element and on smashing of glass this piece will pierce through glass and change over of contacts will take place.
CABLE ENTRIES :- Threaded cable entries are provided at the bottom.
HARDWARE :- All external hardware used will be Stainless Steel.
EARTHING :- Earthing is provided on both sides of the enclosures by 5mm screw with two plain washers and one spring washer. Earthing is
provided on both sides of the enclosures by 5mm screw with two plain washers and one spring washer.
EXTERNAL CANOPY :- Our Pil Boxes are suitable for outdoor mounting without any canopy. We also manufacture Pil Boxes with aluminium
integral canopy.
INSPECTION & TESTING :- Each Pil Box will be subjected to routine tests in accordance with relevant Indian Standards & including the
following:(1) Dimentional check as per drawing. (2) Operation test. (3) Insulation test with 500V Megger.(4) HV Test at 2KV for 60 Seconds.(5)
Earth continuity test. (6)Smashing of glass.
ADVANTAGES OF CAST ALUMINIUM PIL BOX OVER SHEET METAL FABRICATED PILBOX :- (1) Cast Aluminium Pil Box can be made
in any desired and convenient shape and thus nsuring dust,vermin and weather proofness.It is impossible to get any desired shape in sheet
metal.(2) In case of Cast aluminium all individual pieces will be exactly of same size and shape as these are cast out of same mould. Fabricated
boxes are likely to vary in shape on account of human error and other difficulties.(3) Finishing of Cast Aluminium will be superb and same is not
possible in small fabricated boxes.(4) Aluminium is light weight and non corrosive whereas sheet metal is heavy and corrosive. Cast Aluminium
has even good scrap value.
SALIENT FEATURES :- (a) Each PIL BOX is in Cast Aluminium enclosure & epoxy powder coated.(b)Elements is L & T make which is known
for quality and reliability. Even spares are available freely anywhere in India.(c) Better than IP65 Class of Protection.(d) Non deteriorating
Neoprene sponge rubber gasket.
Product Drawing
Code :- HP01
Size :- 170X165X120MM
Specification :- SUPPLY OF CAST ALU. (LM-6) INDUSTRIAL BREAK GLASS
TYPES LCS (PIL BOX) WITH INTEGRAL CANOPY AND WITH 1NO+1NC
CONTACT. (NO CONTACT BECOMES NC WHEN GLASS IS PRESSING THE
CONTACTS BUT WILL BECOME NO WHEN YOU SMASH THE GLASS. SAME
WAY NC CONTACT BECOMES NO WHEN GLASS IS PRESSING THE CONTACTS
BUT WILL BECOME NC WHEN YOU SMASH THE GLASS), WIRED TO 4NOS.
2.5SQMM CONNECTWELL TYPE TERMINALS. GLASS WILL BE PROVIDED ON
COVER SUCH THAT CONTACT ELEMENT WILL REMAIN PRESSED ALL THE
TIME. CHAIN AND HAMMAR WILL BE PROVIDED TO SMASH GLASS IN CASE
OF EMERGENCY OR FIRE. EXTERNAL LEGS ARE PROVIDED FOR
WALL/STRUCTURE MOUNTING. 2:3/4"CABLE ENTRIES WILL BE PROVIDED AT
THE BOTTOM.
Unit Rate in Respective Currencies : *
DESCRIPTION
INDIAN
US DOLLAR
RUPEE
ENCLOSURE WITH HAMMER AND CHAIN
` 1200.00
$ 20.00
WIRING DIAGRAM
Page 1 of 2
Dated:01/Feb/2015
BREAKGLASS TYPE LCS
SIDE VIEW 2
OPEN VIEW
Extra Cost for Providing : *
Sr. No.
01
02
03
04
05
06
07
08
DESCRIPTION
2.5SQMM ELMEX TYPE TERMINAL WITH CHANNEL, END STOP AND END PLATE.
4SQMM ELMEX TYPE TERMINAL WITH CHANNEL, END STOP AND END PLATE.
2.5SQMM PHOENIX MAKE TERMINAL WITH CHANNEL, END STOP AND END PLATE.
M3 STUD TYPE TERMINAL UPTO 6SQMM CABLE.
SHORTING LINK FOR A SET OF TWO TERMINALS WITH SHORTING STUD & LINK.
2.5SQMM ELMEX TERMINAL COMPLETE WITH WIRING FOR ONE TERMINAL.
SIEMENS MAKE ADDITIONAL NO CONTACT OR NC CONTACT.
LED LAMP HOLDER WITHOUT WIRING.
INDIAN RUPEE
` 12.00
` 13.00
` 16.00
` 30.00
` 10.00
` 25.00
` 70.00
` 140.00
US DOLLAR
$ 0.20
$ 0.22
$ 0.27
$ 0.50
$ 0.17
$ 0.42
$ 1.17
$ 2.33
* The prices shown above may vary with time.
Page 2 of 2