1. No category

CADDY ROD LOCK
®
CADDY ROD LOCK
®
CADDY ROD LOCK
®
CADDY ROD LOCK Beam Clamp
®
• Prefabricated assemblies easily lift
and lock into place, helping to
save time and money
• Easy “push-to-install” design
allows installers to simply push
the threaded rod through the
mounting hole, instantly holding
it in position
• Lock nut can be finger tightened, locking the
rod in place
• Works with slightly damaged threads and minor
burrs on the threaded rod
• Conforms with Federal Specification WW-H-171
(Type 23), Manufacturers Standardization Society
ANSI /MSS-SP-58 (Type 19 and 23)
Patent No.: 8,132,767
8,434,725
®
Material: Cast Iron
Finish: Electrogalvanized
Part
Number
Description
CRLB37EG
3/8” Rod, 1/8”–3/8” Flange
F1*
F2*
250 lb
500 lb
*Static Load 1 represents 1/8” to 3/16” (3 mm to 5 mm) flange thickness.
Static Load 2 represents 1/4” to 3/8” (6 mm to 10 mm) flange thickness.
For use on plain and electro zinc plated hardware only.
Recognizing that torque wrenches are generally not used or available on many job sites, the
setscrew should be tightened so it contacts the I-beam and then an additional 1/2 turn added.
CADDY ROD LOCK Beam Clamp,
Thick Flange
®
• Prefabricated assemblies easily lift and lock into
place, helping to save time and money
• Easy “push-to-install” design allows installers
to simply push the threaded rod through the
mounting hole, instantly holding it in position
• Lock nut can be finger tightened, locking the
rod in place
• Works with slightly damaged threads and minor
burrs on the threaded rod
• Conforms with Federal Specification WW-H-171
(Type 23), Manufacturers Standardization Society
ANSI /MSS-SP-58 (Type 19 and 23)
Patent No.: 8,132,767
8,434,725
®
Material: Cast Iron
Finish: Electrogalvanized
Part
Number
F2
F
Description
®
CADDY ROD LOCK
CRLB50EG
F1
1/2” Rod, 3/8”–3/4” Flange
F
1,100 lb
FM Approved for top mount applications only.
For use on plain and electro zinc plated hardware only.
Recognizing that torque wrenches are generally not used or available on many
job sites, the setscrew should be tightened so it contacts the I-beam and then an
additional 1/2 turn added.
®
Ph: 1-800-25-CADDY
www.erico.com
®
138
CADDY ROD LOCK
®
CADDY ROD LOCK Anchor Screw
®
• For use with concrete and solid
brick
• Prefabricated assemblies easily
lift and lock into place, helping
to save time and money
• Works with slightly damaged
threads and minor burrs on the
threaded rod
Patent No.: 8,132,767
8,434,725
Material: Steel
Finish: Electrogalvanized
F2
Part
Number
Description
CRLA37EG
3/8” Rod, 2 7/8” x 1 1/4” x 7/8”
F1
F
F
660 lb
For use on plain and electro zinc plated hardware only.
Tested in 3000 psi (20.67 MPa) concrete.
CADDY ROD LOCK Plywood Form
Preset Anchor
®
• Eliminate overhead drilling into building
structure – CADDY ROD LOCK Preset
Anchors are cast in place
• Nails hold the anchor in place during the
pour and easily break off with a strike of
a hammer once the plywood forms are
removed
• Easy “push-to-install” design allows installers
to simply push the threaded rod through
the mounting hole, instantly holding it in
position
• Works with slightly damaged threads and
minor burrs on the threaded rod
• Prefabricated assemblies easily lift and lock
into place, helping to save time and money
• Plastic flange acts as insert locator when the
forms are removed
• Suitable for use in seismic zones
®
Material: Steel
Finish: Electrogalvanized
Part
Number
Patent No.: 8,132,767
8,434,725
Patent Pending
F2
Description
F
3/8” Rod
1,407 lb
1/2” Rod
1,605 lb
F
®
CADDY ROD LOCK
CRLW37EG
CRLW50EG
F1
Ph: 1-800-25-CADDY
www.erico.com
®
139
CADDY ROD LOCK
®
CADDY ROD LOCK Nut
®
• Easy “push-to-install” design allows installers
to simply push the threaded rod through
the mounting hole, instantly holding it in
position
• Fast installation onto long threaded rods –
push the nut in place instead of threading it
up the rod
• Excellent alignment and easy fine adjustment
by spinning the nut
• Extremely useful in tight spaces where
wrenches are difficult to use
Material: Steel
Finish: Electrogalvanized
Patent No.: 8,132,767
8,434,725
Patent Pending
F2
Part
Number
Description
CRLN37EG
3/8” Rod
F1
F
F
1,350 lb
SN Series Nut
• Allows side mounting of nut to
threaded rod
• Reduces the need for threading
compared to standard nuts and
washers
• Ideal for retrofit projects, such
as trapeze installations
• Works with slightly damaged
threads and minor burrs on the threaded rod
• Reduces installation time up to 50%
Material: Steel
Finish: Electrogalvanized
F2
Part
Number
Description
SN25
1/4” Rod
500 lb
SN37
3/8” Rod
1,350 lb
SN50
1/2” Rod
2,250 lb
F
F1
F
For use on plain and electro zinc plated hardware only.
®
CADDY ROD LOCK
Ph: 1-800-25-CADDY
www.erico.com
®
140
CADDY ROD LOCK
®
CADDY ROD LOCK
Bottom-Mount Duct Bracket
®
• Ideal for modular assembly – allows
attachment of brackets to sections of duct
while safely on the ground
• Slotted holes in bracket allow for horizontal
adjustment of the bracket relative to the duct
• Easy “push-to-install” design allows installers
to simply push the threaded rod through the
mounting hole, instantly holding it in position
• Ready to use out of the box and eliminates
the need for cutting and preparing sections
of strut, angle iron, or strap
• Integrated adjustment nut enables fine tuning
the system height up or down
• Lock nut can be finger tightened, locking the
rod in place
• Extremely useful in tight spaces where
wrenches are difficult to use
Material: Steel
Finish: Electrogalvanized
Patent No.: 8,132,767
8,434,725
Patent Pending
Includes self-tapping
sheet metal screws to
attach bracket to duct
F2
Part
Number
Description
CRLD37BEG
3/8” Rod
F
F1
F
650 lb
CADDY ROD LOCK
Bottom-Mount Duct Bracket, Narrow
®
Material: Steel
Finish: Electrogalvanized
Patent No.: 8,132,767
8,434,725
Patent Pending
Includes self-tapping
sheet metal screws to
attach bracket to duct
F2
Description
CRLD37BNEG
3/8” Rod
F
F
®
Part
Number
F1
CADDY ROD LOCK
• Ideal for modular assembly –
allows attachment of brackets
to sections of duct while safely
on the ground
• Non-slotted bracket allows
for attachment after the final
horizontal position of the duct
is achieved
• Easy “push-to-install” design allows installers
to simply push the threaded rod through the
mounting hole, instantly holding it in position
• Ready to use out of the box and eliminates
the need for cutting and preparing sections
of strut, angle iron, or strap
• Integrated adjustment nut enables fine tuning
the system height up or down
• Lock nut can be finger tightened, locking the
rod in place
• Extremely useful in tight spaces where
wrenches are difficult to use
Ph: 1-800-25-CADDY
www.erico.com
®
141
1,400 lb
CADDY ROD LOCK
®
CADDY ROD LOCK Top-Mount
Duct Bracket
®
• Allows duct to be mounted tight against
the ceiling to maximize overhead space and
reduce the amount of threaded rod required
• Multiple horizontal mounting slots
accommodate insulated duct in tight spaces
• Works with studs in addition to threaded
rods for a more aesthetic installation
• Slotted holes in bracket allow for horizontal
adjustment of the bracket relative to the
duct
• Easy “push-to-install” design allows installers
to simply push the threaded rod through
the mounting hole, instantly holding it in
position
• Ready to use out of the box and eliminates
the need for cutting and preparing sections
of strut, angle iron, or strap
• Integrated adjustment nut enables fine
tuning the system height up or down
• Lock nut can be finger tightened, locking
the rod in place
• Ideal for modular assembly – allows
attachment of brackets to sections of duct
while safely on the ground
• Extremely useful in tight spaces where
wrenches are difficult to use
Material: Steel
Finish: Electrogalvanized
Patent No.: 8,132,767
8,434,725
Patent Pending
Includes self-tapping
sheet metal screws to
attach bracket to duct
F2
Part
Number
Description
CRLD37TEG
3/8” Rod
F1
F
F
650 lb
®
CADDY ROD LOCK
Ph: 1-800-25-CADDY
www.erico.com
®
142
CADDY ROD LOCK
®
CADDY ROD LOCK L-Bracket
®
• Easy “push-to-install” design allows installers
to simply push the threaded rod through
the mounting hole, instantly holding it in
position
• Prefabricated assemblies easily lift and lock
into place, helping to save time and money
• Multiple attachment holes support the use
of either self-drilling screws or bolts, offering
installation options for concrete, wood, and
steel structures
• Lock nut can be finger tightened, locking
the rod in place
• Integrated adjustment nut enables fine
tuning the system height up or down
• Extremely useful in tight spaces where
wrenches are difficult to use
• Conforms with Federal Specification
WW-H-171 (Type 23), Manufacturers
Standardization Society ANSI /MSS-SP-58
(Type 19 and 23)
Patent No.: 8,132,767
8,434,725
Patent Pending
®
Material: Steel
Finish: Electrogalvanized
F2
Part
Number
Description
CRLL37EG
3/8” Rod
F
F1
F
700 lb
Follow fastener manufacturer’s recommended shear and pull-out strength when fastening to the
structure. Fastener not included.
Install in accordance with applicable code.
CADDY ROD LOCK Channel Nut
®
Material: Cast Iron
Finish: Electrogalvanized
Patent No.: 8,132,767
8,434,725
F2
Part
Number
Description
CRLS37EG
3/8” Rod
F
750 lb
F
®
For use on plain and electro zinc plated hardware only.
F1
CADDY ROD LOCK
• Provides fast universal
attachment of threaded rod
and hardware to standard strut
profiles
• Can be used to prefabricate
assemblies which can be
quickly pushed onto previously
installed threaded rods
• Works with slightly damaged threads
and minor burrs on the threaded rod
Ph: 1-800-25-CADDY
www.erico.com
®
143
CADDY ROD LOCK
®
CADDY ROD LOCK Strut,
Perforated
®
• CADDY ROD LOCK
technology allows for the
quick creation, installation,
and adjustment of multi-level
trapeze assemblies
• Ready to use out of the box
and eliminates the need for
cutting and preparing sections
of strut
• Easy “push-to-install” design allows
installers to simply push the threaded
rod through the mounting hole, instantly
holding it in position
• Integrated adjustment nut enables fine
tuning the system height up or down
• Lock nut can be finger tightened, locking
the rod in place
• Works with all accessories that fit standard
A or C type strut channels
®
Material: Steel
Finish: Pregalvanized, Electrogalvanized
Part
Number
Patent No.: 8,132,767
8,434,725
Patent Pending
F2
F1
F
Description
F
Strut Type: A
CRLP237L14
A Strut, 3/8” Rod, 16”
2,668 lb
CRLP237L18
A Strut, 3/8” Rod, 20”
2,075 lb
CRLP237L22
A Strut, 3/8” Rod, 24”
1,698 lb
CRLP237L26
A Strut, 3/8” Rod, 28”
1,437 lb
CRLP237L38
A Strut, 3/8” Rod, 40”
983 lb
CRLP237L50
A Strut, 3/8” Rod, 52”
642 lb
CRLP137L14
C Strut, 3/8” Rod, 16”
789 lb
CRLP137L18
C Strut, 3/8” Rod, 20”
613 lb
CRLP137L22
C Strut, 3/8” Rod, 24”
494 lb
CRLP137L26
C Strut, 3/8” Rod, 28”
354 lb
CRLP137L38
C Strut, 3/8” Rod, 40”
166 lb
Strut Type: C
Static loads are assumed to be uniformly distributed and include a hole factor of 0.92. The
load applied to CADDY ROD LOCK Strut should include a factor of safety appropriate for the
application in which the strut is being used. CADDY ROD LOCK Strut must be installed with
the open side of the channel facing up. For in-door applications only.
®
CADDY ROD LOCK
Ph: 1-800-25-CADDY
www.erico.com
®
144